Merge branch 'pci/host-rockchip' into next

* pci/host-rockchip:
  PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
  PCI: rockchip: Split out rockchip_cfg_atu()
  PCI: rockchip: Clean up bit definitions for PCIE_RC_CONFIG_LCS
  PCI: rockchip: Correct the use of FTS mask
  PCI: rockchip: Remove the pointer to L1 substate cap
  PCI: rockchip: Specify the link capability
  PCI: rockchip: Fix negotiated lanes calculation
  PCI: rockchip: Add Kconfig COMPILE_TEST
  PCI: rockchip: Mark RC as common clock architecture
  PCI: rockchip: Provide captured slot power limit and scale
  PCI: rockchip: Add three new resets as required properties
  PCI: Don't attempt to claim shadow copies of ROM
  PCI: designware: Check for iATU unroll support after initializing host
  PCI: qcom: Fix pp->dev usage before assignment
  PCI: designware-plat: Update author email address
  PCI: layerscape: Fix drvdata usage before assignment
  PCI: designware-plat: Change maintainer to Jose Abreu

Documentation/devicetree/bindings/pci/rockchip-pcie.txt

@@ -26,13 +26,16 @@ Required properties:
 	- "sys"
 	- "legacy"
 	- "client"
-- resets: Must contain five entries for each entry in reset-names.
+- resets: Must contain seven entries for each entry in reset-names.
 	   See ../reset/reset.txt for details.
 - reset-names: Must include the following names
 	- "core"
 	- "mgmt"
 	- "mgmt-sticky"
 	- "pipe"
+	- "pm"
+	- "aclk"
+	- "pclk"
 - pinctrl-names : The pin control state names
 - pinctrl-0: The "default" pinctrl state
 - #interrupt-cells: specifies the number of cells needed to encode an
@@ -86,8 +89,10 @@ pcie0: pcie@f8000000 {
 	reg = <0x0 0xf8000000 0x0 0x2000000>, <0x0 0xfd000000 0x0 0x1000000>;
 	reg-names = "axi-base", "apb-base";
 	resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>,
-		 <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>;
-	reset-names = "core", "mgmt", "mgmt-sticky", "pipe";
+		 <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE> ,
+		 <&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, <&cru SRST_A_PCIE>;
+	reset-names = "core", "mgmt", "mgmt-sticky", "pipe",
+		      "pm", "pclk", "aclk";
 	phys = <&pcie_phy>;
 	phy-names = "pcie-phy";
 	pinctrl-names = "default";

MAINTAINERS

@@ -9300,7 +9300,7 @@ S:	Maintained
 F:	drivers/pci/host/*designware*
 
 PCI DRIVER FOR SYNOPSYS PROTOTYPING DEVICE
-M:	Joao Pinto <jpinto@synopsys.com>
+M:	Jose Abreu <Jose.Abreu@synopsys.com>
 L:	linux-pci@vger.kernel.org
 S:	Maintained
 F:	Documentation/devicetree/bindings/pci/designware-pcie.txt

drivers/pci/host/Kconfig

@@ -278,7 +278,7 @@ config PCIE_ARTPEC6
 
 config PCIE_ROCKCHIP
 	bool "Rockchip PCIe controller"
-	depends on ARCH_ROCKCHIP
+	depends on ARCH_ROCKCHIP || COMPILE_TEST
 	depends on OF
 	depends on PCI_MSI_IRQ_DOMAIN
 	select MFD_SYSCON

drivers/pci/host/pci-layerscape.c

@@ -255,6 +255,7 @@ static int __init ls_pcie_probe(struct platform_device *pdev)
 
 	pp = &pcie->pp;
 	pp->dev = dev;
+	pcie->drvdata = match->data;
 	pp->ops = pcie->drvdata->ops;
 
 	dbi_base = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs");
@@ -262,7 +263,6 @@ static int __init ls_pcie_probe(struct platform_device *pdev)
 	if (IS_ERR(pcie->pp.dbi_base))
 		return PTR_ERR(pcie->pp.dbi_base);
 
-	pcie->drvdata = match->data;
 	pcie->lut = pcie->pp.dbi_base + pcie->drvdata->lut_offset;
 
 	if (!ls_pcie_is_bridge(pcie))

drivers/pci/host/pcie-designware-plat.c

@@ -3,7 +3,7 @@
  *
  * Copyright (C) 2015-2016 Synopsys, Inc. (www.synopsys.com)
  *
- * Authors: Joao Pinto <jpinto@synopsys.com>
+ * Authors: Joao Pinto <jpmpinto@gmail.com>
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as

drivers/pci/host/pcie-designware.c

@@ -637,8 +637,6 @@ int dw_pcie_host_init(struct pcie_port *pp)
 		}
 	}
 
-	pp->iatu_unroll_enabled = dw_pcie_iatu_unroll_enabled(pp);
-
 	if (pp->ops->host_init)
 		pp->ops->host_init(pp);
 
@@ -809,6 +807,11 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
 {
 	u32 val;
 
+	/* get iATU unroll support */
+	pp->iatu_unroll_enabled = dw_pcie_iatu_unroll_enabled(pp);
+	dev_dbg(pp->dev, "iATU unroll: %s\n",
+		pp->iatu_unroll_enabled ? "enabled" : "disabled");
+
 	/* set the number of lanes */
 	val = dw_pcie_readl_rc(pp, PCIE_PORT_LINK_CONTROL);
 	val &= ~PORT_LINK_MODE_MASK;

drivers/pci/host/pcie-qcom.c

@@ -699,11 +699,11 @@ static int qcom_pcie_probe(struct platform_device *pdev)
 	if (IS_ERR(pcie->phy))
 		return PTR_ERR(pcie->phy);
 
+	pp->dev = dev;
 	ret = pcie->ops->get_resources(pcie);
 	if (ret)
 		return ret;
 
-	pp->dev = dev;
 	pp->root_bus_nr = -1;
 	pp->ops = &qcom_pcie_dw_ops;
 

drivers/pci/setup-res.c

@@ -141,6 +141,14 @@ int pci_claim_resource(struct pci_dev *dev, int resource)
 		return -EINVAL;
 	}
 
+	/*
+	 * If we have a shadow copy in RAM, the PCI device doesn't respond
+	 * to the shadow range, so we don't need to claim it, and upstream
+	 * bridges don't need to route the range to the device.
+	 */
+	if (res->flags & IORESOURCE_ROM_SHADOW)
+		return 0;
+
 	root = pci_find_parent_resource(dev, res);
 	if (!root) {
 		dev_info(&dev->dev, "can't claim BAR %d %pR: no compatible bridge window\n",