Input: ad7879 - move header to platform_data directory

The header file is used by the SPI and I2C variant of the driver.
Therefore, move it to a more generic place under platform_data.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

arch/blackfin/mach-bf527/boards/ezbrd.c

@@ -279,7 +279,7 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 #endif
 
 #if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
-#include <linux/spi/ad7879.h>
+#include <linux/platform_data/ad7879.h>
 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 	.model			= 7879,	/* Model = AD7879 */
 	.x_plate_ohms		= 620,	/* 620 Ohm from the touch datasheet */

arch/blackfin/mach-bf527/boards/ezkit.c

@@ -477,7 +477,7 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 #endif
 
 #if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
-#include <linux/spi/ad7879.h>
+#include <linux/platform_data/ad7879.h>
 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 	.model			= 7879,	/* Model = AD7879 */
 	.x_plate_ohms		= 620,	/* 620 Ohm from the touch datasheet */

arch/blackfin/mach-bf527/boards/tll6527m.c

@@ -29,7 +29,7 @@
 #include <asm/dpmc.h>
 
 #if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
-#include <linux/spi/ad7879.h>
+#include <linux/platform_data/ad7879.h>
 #define LCD_BACKLIGHT_GPIO 0x40
 /* TLL6527M uses TLL7UIQ35 / ADI LCD EZ Extender. AD7879 AUX GPIO is used for
  * LCD Backlight Enable

arch/blackfin/mach-bf537/boards/stamp.c

@@ -776,7 +776,7 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 #endif
 
 #if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
-#include <linux/spi/ad7879.h>
+#include <linux/platform_data/ad7879.h>
 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 	.model			= 7879,	/* Model = AD7879 */
 	.x_plate_ohms		= 620,	/* 620 Ohm from the touch datasheet */

arch/blackfin/mach-bf538/boards/ezkit.c

@@ -521,7 +521,7 @@ static struct bfin5xx_spi_chip spi_flash_chip_info = {
 #endif	/* CONFIG_SPI_BFIN5XX */
 
 #if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
-#include <linux/spi/ad7879.h>
+#include <linux/platform_data/ad7879.h>
 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 	.model			= 7879,	/* Model = AD7879 */
 	.x_plate_ohms		= 620,	/* 620 Ohm from the touch datasheet */

drivers/input/touchscreen/ad7879.c

@@ -31,7 +31,7 @@
 #include <linux/i2c.h>
 #include <linux/gpio.h>
 
-#include <linux/spi/ad7879.h>
+#include <linux/platform_data/ad7879.h>
 #include <linux/module.h>
 #include "ad7879.h"
 
@@ -170,10 +170,10 @@ static int ad7879_report(struct ad7879 *ts)
 	 * filter.  The combination of these two techniques provides a robust
 	 * solution, discarding the spurious noise in the signal and keeping
 	 * only the data of interest.  The size of both filters is
-	 * programmable. (dev.platform_data, see linux/spi/ad7879.h) Other
-	 * user-programmable conversion controls include variable acquisition
-	 * time, and first conversion delay. Up to 16 averages can be taken
-	 * per conversion.
+	 * programmable. (dev.platform_data, see linux/platform_data/ad7879.h)
+	 * Other user-programmable conversion controls include variable
+	 * acquisition time, and first conversion delay. Up to 16 averages can
+	 * be taken per conversion.
 	 */
 
 	if (likely(x && z1)) {

include/linux/spi/ad7879.h → include/linux/platform_data/ad7879.h

-/* linux/spi/ad7879.h */
+/* linux/platform_data/ad7879.h */
 
 /* Touchscreen characteristics vary between boards and models.  The
  * platform_data for the device's "struct device" holds this information.