media: staging: improve comments usage in atomisp-ov5693

- Fix "Block comments use a trailing */ on a separate line" checkpatch
  issue
- Fix "Block comments use * on subsequent lines" checkpatch issue
Signed-off-by: Riccardo Schirone <sirmy15@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

drivers/staging/media/atomisp/i2c/ov5693/atomisp-ov5693.c

@@ -213,7 +213,8 @@ static int vcm_dw_i2c_write(struct i2c_client *client, u16 data)
 	return ret == num_msg ? 0 : -EIO;
 }
 
-/* Theory: per datasheet, the two VCMs both allow for a 2-byte read.
+/*
+ * Theory: per datasheet, the two VCMs both allow for a 2-byte read.
  * The DW9714 doesn't actually specify what this does (it has a
  * two-byte write-only protocol, but specifies the read sequence as
  * legal), but it returns the same data (zeroes) always, after an
@@ -224,7 +225,8 @@ static int vcm_dw_i2c_write(struct i2c_client *client, u16 data)
  * these) in AD5823 are not pairwise repetitions of the same 16 bit
  * word.  So all we have to do is sequentially read two bytes at a
  * time and see if we detect a difference in any of the first four
- * pairs.  */
+ * pairs.
+ */
 static int vcm_detect(struct i2c_client *client)
 {
 	int i, ret;
@@ -238,8 +240,10 @@ static int vcm_detect(struct i2c_client *client)
 		msg.buf = (u8 *)&data;
 		ret = i2c_transfer(client->adapter, &msg, 1);
 
-		/* DW9714 always fails the first read and returns
-		 * zeroes for subsequent ones */
+		/*
+		 * DW9714 always fails the first read and returns
+		 * zeroes for subsequent ones
+		 */
 		if (i == 0 && ret == -EREMOTEIO) {
 			data0 = 0;
 			continue;
@@ -533,9 +537,11 @@ static long __ov5693_set_exposure(struct v4l2_subdev *sd, int coarse_itg,
 
 	hts = ov5693_res[dev->fmt_idx].pixels_per_line;
 	vts = ov5693_res[dev->fmt_idx].lines_per_frame;
-	/*If coarse_itg is larger than 1<<15, can not write to reg directly.
-	  The way is to write coarse_itg/2 to the reg, meanwhile write 2*hts
-	  to the reg. */
+	/*
+	 * If coarse_itg is larger than 1<<15, can not write to reg directly.
+	 * The way is to write coarse_itg/2 to the reg, meanwhile write 2*hts
+	 * to the reg.
+	 */
 	if (coarse_itg > (1 << 15)) {
 		hts = hts * 2;
 		coarse_itg = (int)coarse_itg / 2;
@@ -880,8 +886,10 @@ static long ov5693_ioctl(struct v4l2_subdev *sd, unsigned int cmd, void *arg)
 	return 0;
 }
 
-/* This returns the exposure time being used. This should only be used
-   for filling in EXIF data, not for actual image processing. */
+/*
+ * This returns the exposure time being used. This should only be used
+ * for filling in EXIF data, not for actual image processing.
+ */
 static int ov5693_q_exposure(struct v4l2_subdev *sd, s32 *value)
 {
 	struct i2c_client *client = v4l2_get_subdevdata(sd);
@@ -1298,11 +1306,13 @@ static int power_ctrl(struct v4l2_subdev *sd, bool flag)
 	if (!dev || !dev->platform_data)
 		return -ENODEV;
 
-	/* This driver assumes "internal DVDD, PWDNB tied to DOVDD".
+	/*
+	 * This driver assumes "internal DVDD, PWDNB tied to DOVDD".
 	 * In this set up only gpio0 (XSHUTDN) should be available
 	 * but in some products (for example ECS) gpio1 (PWDNB) is
 	 * also available. If gpio1 is available we emulate it being
-	 * tied to DOVDD here. */
+	 * tied to DOVDD here.
+	 */
 	if (flag) {
 		ret = dev->platform_data->v2p8_ctrl(sd, 1);
 		dev->platform_data->gpio1_ctrl(sd, 1);
@@ -1941,10 +1951,12 @@ static int ov5693_probe(struct i2c_client *client)
 	struct acpi_device *adev;
 	unsigned int i;
 
-	/* Firmware workaround: Some modules use a "secondary default"
+	/*
+	 * Firmware workaround: Some modules use a "secondary default"
 	 * address of 0x10 which doesn't appear on schematics, and
 	 * some BIOS versions haven't gotten the memo.  Work around
-	 * via config. */
+	 * via config.
+	 */
 	i2c = gmin_get_var_int(&client->dev, "I2CAddr", -1);
 	if (i2c != -1) {
 		dev_info(&client->dev,