x86: Fix a handful of typos

Fix a couple of typos in code comments.

 [ bp: While at it: s/IRQ's/IRQs/. ]
Signed-off-by: Martin Molnar <martin.molnar.programming@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lkml.kernel.org/r/0819a044-c360-44a4-f0b6-3f5bafe2d35c@gmail.com

arch/x86/kernel/irqinit.c

@@ -84,7 +84,7 @@ void __init init_IRQ(void)
 	 * On cpu 0, Assign ISA_IRQ_VECTOR(irq) to IRQ 0..15.
 	 * If these IRQ's are handled by legacy interrupt-controllers like PIC,
 	 * then this configuration will likely be static after the boot. If
-	 * these IRQ's are handled by more mordern controllers like IO-APIC,
+	 * these IRQs are handled by more modern controllers like IO-APIC,
 	 * then this vector space can be freed and re-used dynamically as the
 	 * irq's migrate etc.
 	 */

arch/x86/kernel/nmi.c

@@ -403,9 +403,9 @@ static void default_do_nmi(struct pt_regs *regs)
 	 * a 'real' unknown NMI.  For example, while processing
 	 * a perf NMI another perf NMI comes in along with a
 	 * 'real' unknown NMI.  These two NMIs get combined into
-	 * one (as descibed above).  When the next NMI gets
+	 * one (as described above).  When the next NMI gets
 	 * processed, it will be flagged by perf as handled, but
-	 * noone will know that there was a 'real' unknown NMI sent
+	 * no one will know that there was a 'real' unknown NMI sent
 	 * also.  As a result it gets swallowed.  Or if the first
 	 * perf NMI returns two events handled then the second
 	 * NMI will get eaten by the logic below, again losing a

arch/x86/kernel/reboot.c

@@ -531,7 +531,7 @@ static void emergency_vmx_disable_all(void)
 
 	/*
 	 * We need to disable VMX on all CPUs before rebooting, otherwise
-	 * we risk hanging up the machine, because the CPU ignore INIT
+	 * we risk hanging up the machine, because the CPU ignores INIT
 	 * signals when VMX is enabled.
 	 *
 	 * We can't take any locks and we may be on an inconsistent

arch/x86/kernel/smpboot.c

@@ -1434,7 +1434,7 @@ early_param("possible_cpus", _setup_possible_cpus);
 /*
  * cpu_possible_mask should be static, it cannot change as cpu's
  * are onlined, or offlined. The reason is per-cpu data-structures
- * are allocated by some modules at init time, and dont expect to
+ * are allocated by some modules at init time, and don't expect to
  * do this dynamically on cpu arrival/departure.
  * cpu_present_mask on the other hand can change dynamically.
  * In case when cpu_hotplug is not compiled, then we resort to current

arch/x86/kernel/tsc.c

@@ -477,7 +477,7 @@ static unsigned long pit_calibrate_tsc(u32 latch, unsigned long ms, int loopmin)
  * transition from one expected value to another with a fairly
  * high accuracy, and we didn't miss any events. We can thus
  * use the TSC value at the transitions to calculate a pretty
- * good value for the TSC frequencty.
+ * good value for the TSC frequency.
  */
 static inline int pit_verify_msb(unsigned char val)
 {

arch/x86/kernel/tsc_sync.c

@@ -295,7 +295,7 @@ static cycles_t check_tsc_warp(unsigned int timeout)
  * But as the TSC is per-logical CPU and can potentially be modified wrongly
  * by the bios, TSC sync test for smaller duration should be able
  * to catch such errors. Also this will catch the condition where all the
- * cores in the socket doesn't get reset at the same time.
+ * cores in the socket don't get reset at the same time.
  */
 static inline unsigned int loop_timeout(int cpu)
 {