[PATCH] ia64: make madt parsing quieter

We already get this info in other forms from other boot messages, so kill the 
printing of the MADT entries as they're parsed.  This patch significantly 
reduces the amount of output from a boot of a 512p system.
Signed-off-by: Jesse Barnes <jbarnes@sgi.com>
Signed-off-by: David Mosberger <davidm@hpl.hp.com>

arch/ia64/kernel/acpi.c

@@ -171,8 +171,6 @@ acpi_parse_lapic_addr_ovr (
 	if (BAD_MADT_ENTRY(lapic, end))
 		return -EINVAL;
 
-	acpi_table_print_madt_entry(header);
-
 	if (lapic->address) {
 		iounmap((void *) ipi_base_addr);
 		ipi_base_addr = (unsigned long) ioremap(lapic->address, 0);
@@ -191,25 +189,13 @@ acpi_parse_lsapic (acpi_table_entry_header *header, const unsigned long end)
 	if (BAD_MADT_ENTRY(lsapic, end))
 		return -EINVAL;
 
-	acpi_table_print_madt_entry(header);
-
-	printk(KERN_INFO "CPU %d (0x%04x)", total_cpus, (lsapic->id << 8) | lsapic->eid);
-
-	if (!lsapic->flags.enabled)
-		printk(" disabled");
-	else {
-		printk(" enabled");
+	if (lsapic->flags.enabled) {
 #ifdef CONFIG_SMP
 		smp_boot_data.cpu_phys_id[available_cpus] = (lsapic->id << 8) | lsapic->eid;
-		if (hard_smp_processor_id()
-		    == (unsigned int) smp_boot_data.cpu_phys_id[available_cpus])
-			printk(" (BSP)");
 #endif
 		++available_cpus;
 	}
 
-	printk("\n");
-
 	total_cpus++;
 	return 0;
 }
@@ -225,8 +211,6 @@ acpi_parse_lapic_nmi (acpi_table_entry_header *header, const unsigned long end)
 	if (BAD_MADT_ENTRY(lacpi_nmi, end))
 		return -EINVAL;
 
-	acpi_table_print_madt_entry(header);
-
 	/* TBD: Support lapic_nmi entries */
 	return 0;
 }
@@ -242,8 +226,6 @@ acpi_parse_iosapic (acpi_table_entry_header *header, const unsigned long end)
 	if (BAD_MADT_ENTRY(iosapic, end))
 		return -EINVAL;
 
-	acpi_table_print_madt_entry(header);
-
 	iosapic_init(iosapic->address, iosapic->global_irq_base);
 
 	return 0;
@@ -262,8 +244,6 @@ acpi_parse_plat_int_src (
 	if (BAD_MADT_ENTRY(plintsrc, end))
 		return -EINVAL;
 
-	acpi_table_print_madt_entry(header);
-
 	/*
 	 * Get vector assignment for this interrupt, set attributes,
 	 * and program the IOSAPIC routing table.
@@ -292,8 +272,6 @@ acpi_parse_int_src_ovr (
 	if (BAD_MADT_ENTRY(p, end))
 		return -EINVAL;
 
-	acpi_table_print_madt_entry(header);
-
 	iosapic_override_isa_irq(p->bus_irq, p->global_irq,
 				 (p->flags.polarity == 1) ? IOSAPIC_POL_HIGH : IOSAPIC_POL_LOW,
 				 (p->flags.trigger == 1) ? IOSAPIC_EDGE : IOSAPIC_LEVEL);
@@ -311,8 +289,6 @@ acpi_parse_nmi_src (acpi_table_entry_header *header, const unsigned long end)
 	if (BAD_MADT_ENTRY(nmi_src, end))
 		return -EINVAL;
 
-	acpi_table_print_madt_entry(header);
-
 	/* TBD: Support nimsrc entries */
 	return 0;
 }