Commit 5177b324 authored by Rafael J. Wysocki's avatar Rafael J. Wysocki Committed by Jeff Garzik

skge: adapt skge to use reworked PCI PM

Adapt the skge driver to the reworked PCI PM

* Use device_set_wakeup_enable() and friends as needed
* Remove an open-coded reference to the standard PCI PM registers
* Use pci_prepare_to_sleep() and pci_back_from_sleep() in the
  ->suspend() and ->resume() callbacks
* Use the observation that it is sufficient to call pci_enable_wake()
  once, unless it fails

Tested on Asus L5D (Yukon-Lite rev 7).
Signed-off-by: default avatarRafael J. Wysocki <rjw@sisk.pl>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarJeff Garzik <jgarzik@redhat.com>
parent c8db3fec
......@@ -149,24 +149,6 @@ static u32 wol_supported(const struct skge_hw *hw)
return WAKE_MAGIC | WAKE_PHY;
}
static u32 pci_wake_enabled(struct pci_dev *dev)
{
int pm = pci_find_capability(dev, PCI_CAP_ID_PM);
u16 value;
/* If device doesn't support PM Capabilities, but request is to disable
* wake events, it's a nop; otherwise fail */
if (!pm)
return 0;
pci_read_config_word(dev, pm + PCI_PM_PMC, &value);
value &= PCI_PM_CAP_PME_MASK;
value >>= ffs(PCI_PM_CAP_PME_MASK) - 1; /* First bit of mask */
return value != 0;
}
static void skge_wol_init(struct skge_port *skge)
{
struct skge_hw *hw = skge->hw;
......@@ -254,10 +236,14 @@ static int skge_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
struct skge_port *skge = netdev_priv(dev);
struct skge_hw *hw = skge->hw;
if (wol->wolopts & ~wol_supported(hw))
if ((wol->wolopts & ~wol_supported(hw))
|| !device_can_wakeup(&hw->pdev->dev))
return -EOPNOTSUPP;
skge->wol = wol->wolopts;
device_set_wakeup_enable(&hw->pdev->dev, skge->wol);
return 0;
}
......@@ -3856,7 +3842,7 @@ static struct net_device *skge_devinit(struct skge_hw *hw, int port,
skge->speed = -1;
skge->advertising = skge_supported_modes(hw);
if (pci_wake_enabled(hw->pdev))
if (device_may_wakeup(&hw->pdev->dev))
skge->wol = wol_supported(hw) & WAKE_MAGIC;
hw->dev[port] = dev;
......@@ -4081,8 +4067,8 @@ static int skge_suspend(struct pci_dev *pdev, pm_message_t state)
}
skge_write32(hw, B0_IMSK, 0);
pci_enable_wake(pdev, pci_choose_state(pdev, state), wol);
pci_set_power_state(pdev, pci_choose_state(pdev, state));
pci_prepare_to_sleep(pdev);
return 0;
}
......@@ -4095,7 +4081,7 @@ static int skge_resume(struct pci_dev *pdev)
if (!hw)
return 0;
err = pci_set_power_state(pdev, PCI_D0);
err = pci_back_from_sleep(pdev);
if (err)
goto out;
......@@ -4103,8 +4089,6 @@ static int skge_resume(struct pci_dev *pdev)
if (err)
goto out;
pci_enable_wake(pdev, PCI_D0, 0);
err = skge_reset(hw);
if (err)
goto out;
......@@ -4145,8 +4129,8 @@ static void skge_shutdown(struct pci_dev *pdev)
wol |= skge->wol;
}
pci_enable_wake(pdev, PCI_D3hot, wol);
pci_enable_wake(pdev, PCI_D3cold, wol);
if (pci_enable_wake(pdev, PCI_D3cold, wol))
pci_enable_wake(pdev, PCI_D3hot, wol);
pci_disable_device(pdev);
pci_set_power_state(pdev, PCI_D3hot);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment