GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder

Move the 2 drivers from arch/mips/lantiq/xway/ to the subsystem and make them
buildable.

The following 2 patches will convert the drivers to OF.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3838/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

arch/mips/lantiq/xway/Makefile

-obj-y := prom.o sysctrl.o clk.o reset.o gpio.o gpio_stp.o gpio_ebu.o dma.o
+obj-y := prom.o sysctrl.o clk.o reset.o gpio.o dma.o

drivers/gpio/Kconfig

@@ -96,6 +96,14 @@ config GPIO_EP93XX
 	depends on ARCH_EP93XX
 	select GPIO_GENERIC
 
+config GPIO_MM_LANTIQ
+	bool "Lantiq Memory mapped GPIOs"
+	depends on LANTIQ && SOC_XWAY
+	help
+	  This enables support for memory mapped GPIOs on the External Bus Unit
+	  (EBU) found on Lantiq SoCs. The gpios are output only as they are
+	  created by attaching a 16bit latch to the bus.
+
 config GPIO_MPC5200
 	def_bool y
 	depends on PPC_MPC52xx
@@ -306,6 +314,16 @@ config GPIO_STMPE
 	  This enables support for the GPIOs found on the STMPE I/O
 	  Expanders.
 
+config GPIO_STP_XWAY
+	bool "XWAY STP GPIOs"
+	depends on SOC_XWAY
+	help
+	  This enables support for the Serial To Parallel (STP) unit found on
+	  XWAY SoC. The STP allows the SoC to drive a shift registers cascade,
+	  that can be up to 24 bit. This peripheral is aimed at driving leds.
+	  Some of the gpios/leds can be auto updated by the soc with dsl and
+	  phy status.
+
 config GPIO_TC3589X
 	bool "TC3589X GPIOs"
 	depends on MFD_TC3589X

drivers/gpio/Makefile

@@ -30,6 +30,7 @@ obj-$(CONFIG_GPIO_MC33880)	+= gpio-mc33880.o
 obj-$(CONFIG_GPIO_MC9S08DZ60)	+= gpio-mc9s08dz60.o
 obj-$(CONFIG_GPIO_MCP23S08)	+= gpio-mcp23s08.o
 obj-$(CONFIG_GPIO_ML_IOH)	+= gpio-ml-ioh.o
+obj-$(CONFIG_GPIO_MM_LANTIQ)	+= gpio-mm-lantiq.o
 obj-$(CONFIG_GPIO_MPC5200)	+= gpio-mpc5200.o
 obj-$(CONFIG_GPIO_MPC8XXX)	+= gpio-mpc8xxx.o
 obj-$(CONFIG_GPIO_MSM_V1)	+= gpio-msm-v1.o
@@ -49,6 +50,7 @@ obj-$(CONFIG_ARCH_SA1100)	+= gpio-sa1100.o
 obj-$(CONFIG_GPIO_SCH)		+= gpio-sch.o
 obj-$(CONFIG_GPIO_SODAVILLE)	+= gpio-sodaville.o
 obj-$(CONFIG_GPIO_STMPE)	+= gpio-stmpe.o
+obj-$(CONFIG_GPIO_STP_XWAY)	+= gpio-stp-xway.o
 obj-$(CONFIG_GPIO_SX150X)	+= gpio-sx150x.o
 obj-$(CONFIG_GPIO_TC3589X)	+= gpio-tc3589x.o
 obj-$(CONFIG_ARCH_TEGRA)	+= gpio-tegra.o