Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2018-01-12

This series contains updates to ixgbe, fm10k and net core.

Alex updates the driver to remove a duplicate MAC address check and
verifies that we have not run out of resources to configure a MAC rule
in our filter table.  Also do not assume that dev->num_tc was populated
and configured with the driver, since it can be configured via mqprio
without any hardware coordination.  Fixed the recording of stats for
MACVLAN in ixgbe and fm10k instead of recording the receive queue on
MACVLAN offloaded frames.  When handling a MACVLAN offload, we should
be stopping/starting traffic on our own queues instead of the upper
devices transmit queues.  Fixed possible race conditions with the
MACVLAN cleanup with the interface cleanup on shutdown.  With the
recent fixes to ixgbe, we can cap the number of queues regardless of
accel_priv being in use or not, since the actual number of queues are
being reported via real_num_tx_queues.

Tony fixes up the kernel documentation for ixgbe and ixgbevf to resolve
warnings when W=1 is used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/intel/fm10k/fm10k_main.c

@@ -446,13 +446,13 @@ static void fm10k_type_trans(struct fm10k_ring *rx_ring,
 
 	skb->protocol = eth_type_trans(skb, dev);
 
+	/* Record Rx queue, or update macvlan statistics */
 	if (!l2_accel)
-		return;
-
-	/* update MACVLAN statistics */
-	macvlan_count_rx(netdev_priv(dev), skb->len + ETH_HLEN, 1,
-			 !!(rx_desc->w.hdr_info &
-			    cpu_to_le16(FM10K_RXD_HDR_INFO_XC_MASK)));
+		skb_record_rx_queue(skb, rx_ring->queue_index);
+	else
+		macvlan_count_rx(netdev_priv(dev), skb->len + ETH_HLEN, true,
+				 (skb->pkt_type == PACKET_BROADCAST) ||
+				 (skb->pkt_type == PACKET_MULTICAST));
 }
 
 /**
@@ -479,8 +479,6 @@ static unsigned int fm10k_process_skb_fields(struct fm10k_ring *rx_ring,
 
 	FM10K_CB(skb)->fi.w.vlan = rx_desc->w.vlan;
 
-	skb_record_rx_queue(skb, rx_ring->queue_index);
-
 	FM10K_CB(skb)->fi.d.glort = rx_desc->d.glort;
 
 	if (rx_desc->w.vlan) {

drivers/net/ethernet/intel/ixgbe/ixgbe.h

@@ -674,6 +674,7 @@ struct ixgbe_adapter {
 	struct ieee_ets *ixgbe_ieee_ets;
 	struct ixgbe_dcb_config dcb_cfg;
 	struct ixgbe_dcb_config temp_dcb_cfg;
+	u8 hw_tcs;
 	u8 dcb_set_bitmap;
 	u8 dcbx_cap;
 	enum ixgbe_fc_mode last_lfc_mode;

drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c

@@ -431,6 +431,7 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw)
 /**
  *  ixgbe_start_mac_link_82598 - Configures MAC link settings
  *  @hw: pointer to hardware structure
+ *  @autoneg_wait_to_complete: true when waiting for completion is needed
  *
  *  Configures link settings based on values in the ixgbe_hw struct.
  *  Restarts the link.  Performs autonegotiation if needed.
@@ -1054,7 +1055,7 @@ static s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset,
  *  ixgbe_read_i2c_sff8472_82598 - Reads 8 bit word over I2C interface.
  *  @hw: pointer to hardware structure
  *  @byte_offset: byte offset at address 0xA2
- *  @eeprom_data: value read
+ *  @sff8472_data: value read
  *
  *  Performs 8 byte read operation to SFP module's SFF-8472 data over I2C
  **/

drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c

@@ -221,7 +221,7 @@ static s32 prot_autoc_read_82599(struct ixgbe_hw *hw, bool *locked,
 /**
  * prot_autoc_write_82599 - Hides MAC differences needed for AUTOC write
  * @hw: pointer to hardware structure
- * @reg_val: value to write to AUTOC
+ * @autoc: value to write to AUTOC
  * @locked: bool to indicate whether the SW/FW lock was already taken by
  *	     previous proc_autoc_read_82599.
  *
@@ -1310,10 +1310,11 @@ do { \
 
 /**
  *  ixgbe_atr_compute_sig_hash_82599 - Compute the signature hash
- *  @stream: input bitstream to compute the hash on
+ *  @input: input bitstream to compute the hash on
+ *  @common: compressed common input dword
  *
  *  This function is almost identical to the function above but contains
- *  several optomizations such as unwinding all of the loops, letting the
+ *  several optimizations such as unwinding all of the loops, letting the
  *  compiler work out all of the conditional ifs since the keys are static
  *  defines, and computing two keys at once since the hashed dword stream
  *  will be the same for both keys.
@@ -1446,7 +1447,7 @@ do { \
 
 /**
  *  ixgbe_atr_compute_perfect_hash_82599 - Compute the perfect filter hash
- *  @atr_input: input bitstream to compute the hash on
+ *  @input: input bitstream to compute the hash on
  *  @input_mask: mask for the input bitstream
  *
  *  This function serves two main purposes.  First it applies the input_mask
@@ -2078,6 +2079,7 @@ static s32 ixgbe_reset_pipeline_82599(struct ixgbe_hw *hw)
  *  ixgbe_read_i2c_byte_82599 - Reads 8 bit word over I2C
  *  @hw: pointer to hardware structure
  *  @byte_offset: byte offset to read
+ *  @dev_addr: address to read from
  *  @data: value read
  *
  *  Performs byte read operation to SFP module's EEPROM over I2C interface at
@@ -2131,6 +2133,7 @@ static s32 ixgbe_read_i2c_byte_82599(struct ixgbe_hw *hw, u8 byte_offset,
  *  ixgbe_write_i2c_byte_82599 - Writes 8 bit word over I2C
  *  @hw: pointer to hardware structure
  *  @byte_offset: byte offset to write
+ *  @dev_addr: address to write to
  *  @data: value to write
  *
  *  Performs byte write operation to SFP module's EEPROM over I2C interface at

drivers/net/ethernet/intel/ixgbe/ixgbe_common.c

@@ -1613,6 +1613,7 @@ static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data,
 /**
  *  ixgbe_shift_in_eeprom_bits - Shift data bits in from the EEPROM
  *  @hw: pointer to hardware structure
+ *  @count: number of bits to shift
  **/
 static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count)
 {
@@ -1667,7 +1668,7 @@ static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec)
 /**
  *  ixgbe_lower_eeprom_clk - Lowers the EEPROM's clock input.
  *  @hw: pointer to hardware structure
- *  @eecd: EECD's current value
+ *  @eec: EEC's current value
  **/
 static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec)
 {
@@ -2037,7 +2038,7 @@ static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr)
 /**
  *  ixgbe_set_mta - Set bit-vector in multicast table
  *  @hw: pointer to hardware structure
- *  @hash_value: Multicast address hash value
+ *  @mc_addr: Multicast address
  *
  *  Sets the bit-vector in the multicast table.
  **/
@@ -3086,6 +3087,8 @@ s32 ixgbe_init_uta_tables_generic(struct ixgbe_hw *hw)
  *  ixgbe_find_vlvf_slot - find the vlanid or the first empty slot
  *  @hw: pointer to hardware structure
  *  @vlan: VLAN id to write to VLAN filter
+ *  @vlvf_bypass: true to find vlanid only, false returns first empty slot if
+ *		  vlanid not found
  *
  *  return the VLVF index where this VLAN id should be placed
  *
@@ -3476,7 +3479,7 @@ void ixgbe_set_mac_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf)
  *  ixgbe_set_vlan_anti_spoofing - Enable/Disable VLAN anti-spoofing
  *  @hw: pointer to hardware structure
  *  @enable: enable or disable switch for VLAN anti-spoofing
- *  @pf: Virtual Function pool - VF Pool to set for VLAN anti-spoofing
+ *  @vf: Virtual Function pool - VF Pool to set for VLAN anti-spoofing
  *
  **/
 void ixgbe_set_vlan_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf)

drivers/net/ethernet/intel/ixgbe/ixgbe_dcb.c

@@ -39,6 +39,10 @@
  * are the smallest unit programmable into the underlying
  * hardware. The IEEE 802.1Qaz specification do not use bandwidth
  * groups so this is much simplified from the CEE case.
+ * @bw: bandwidth index by traffic class
+ * @refill: refill credits index by traffic class
+ * @max: max credits by traffic class
+ * @max_frame: maximum frame size
  */
 static s32 ixgbe_ieee_credits(__u8 *bw, __u16 *refill,
 			      __u16 *max, int max_frame)
@@ -72,8 +76,10 @@ static s32 ixgbe_ieee_credits(__u8 *bw, __u16 *refill,
 
 /**
  * ixgbe_dcb_calculate_tc_credits - Calculates traffic class credits
- * @ixgbe_dcb_config: Struct containing DCB settings.
- * @direction: Configuring either Tx or Rx.
+ * @hw: pointer to hardware structure
+ * @dcb_config: Struct containing DCB settings
+ * @max_frame: Maximum frame size
+ * @direction: Configuring either Tx or Rx
  *
  * This function calculates the credits allocated to each traffic class.
  * It should be called only after the rules are checked by

drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_82598.c

@@ -34,7 +34,9 @@
 /**
  * ixgbe_dcb_config_rx_arbiter_82598 - Config Rx data arbiter
  * @hw: pointer to hardware structure
- * @dcb_config: pointer to ixgbe_dcb_config structure
+ * @refill: refill credits index by traffic class
+ * @max: max credits index by traffic class
+ * @prio_type: priority type indexed by traffic class
  *
  * Configure Rx Data Arbiter and credits for each traffic class.
  */
@@ -91,7 +93,10 @@ s32 ixgbe_dcb_config_rx_arbiter_82598(struct ixgbe_hw *hw,
 /**
  * ixgbe_dcb_config_tx_desc_arbiter_82598 - Config Tx Desc. arbiter
  * @hw: pointer to hardware structure
- * @dcb_config: pointer to ixgbe_dcb_config structure
+ * @refill: refill credits index by traffic class
+ * @max: max credits index by traffic class
+ * @bwg_id: bandwidth grouping indexed by traffic class
+ * @prio_type: priority type indexed by traffic class
  *
  * Configure Tx Descriptor Arbiter and credits for each traffic class.
  */
@@ -137,7 +142,10 @@ s32 ixgbe_dcb_config_tx_desc_arbiter_82598(struct ixgbe_hw *hw,
 /**
  * ixgbe_dcb_config_tx_data_arbiter_82598 - Config Tx data arbiter
  * @hw: pointer to hardware structure
- * @dcb_config: pointer to ixgbe_dcb_config structure
+ * @refill: refill credits index by traffic class
+ * @max: max credits index by traffic class
+ * @bwg_id: bandwidth grouping indexed by traffic class
+ * @prio_type: priority type indexed by traffic class
  *
  * Configure Tx Data Arbiter and credits for each traffic class.
  */
@@ -184,7 +192,7 @@ s32 ixgbe_dcb_config_tx_data_arbiter_82598(struct ixgbe_hw *hw,
 /**
  * ixgbe_dcb_config_pfc_82598 - Config priority flow control
  * @hw: pointer to hardware structure
- * @dcb_config: pointer to ixgbe_dcb_config structure
+ * @pfc_en: enabled pfc bitmask
  *
  * Configure Priority Flow Control for each traffic class.
  */
@@ -269,7 +277,11 @@ static s32 ixgbe_dcb_config_tc_stats_82598(struct ixgbe_hw *hw)
 /**
  * ixgbe_dcb_hw_config_82598 - Config and enable DCB
  * @hw: pointer to hardware structure
- * @dcb_config: pointer to ixgbe_dcb_config structure
+ * @pfc_en: enabled pfc bitmask
+ * @refill: refill credits index by traffic class
+ * @max: max credits index by traffic class
+ * @bwg_id: bandwidth grouping indexed by traffic class
+ * @prio_type: priority type indexed by traffic class
  *
  * Configure dcb settings and enable dcb mode.
  */

drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_82599.c

@@ -38,6 +38,7 @@
  * @max: max credits index by traffic class
  * @bwg_id: bandwidth grouping indexed by traffic class
  * @prio_type: priority type indexed by traffic class
+ * @prio_tc: priority to tc assignments indexed by priority
  *
  * Configure Rx Packet Arbiter and credits for each traffic class.
  */
@@ -148,6 +149,7 @@ s32 ixgbe_dcb_config_tx_desc_arbiter_82599(struct ixgbe_hw *hw,
  * @max: max credits index by traffic class
  * @bwg_id: bandwidth grouping indexed by traffic class
  * @prio_type: priority type indexed by traffic class
+ * @prio_tc: priority to tc assignments indexed by priority
  *
  * Configure Tx Packet Arbiter and credits for each traffic class.
  */
@@ -344,11 +346,12 @@ static s32 ixgbe_dcb_config_tc_stats_82599(struct ixgbe_hw *hw)
 /**
  * ixgbe_dcb_hw_config_82599 - Configure and enable DCB
  * @hw: pointer to hardware structure
+ * @pfc_en: enabled pfc bitmask
  * @refill: refill credits index by traffic class
  * @max: max credits index by traffic class
  * @bwg_id: bandwidth grouping indexed by traffic class
  * @prio_type: priority type indexed by traffic class
- * @pfc_en: enabled pfc bitmask
+ * @prio_tc: priority to tc assignments indexed by priority
  *
  * Configure dcb settings and enable dcb mode.
  */

drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_nl.c

@@ -571,7 +571,7 @@ static int ixgbe_dcbnl_ieee_setets(struct net_device *dev,
 	if (max_tc > adapter->dcb_cfg.num_tcs.pg_tcs)
 		return -EINVAL;
 
-	if (max_tc != netdev_get_num_tc(dev)) {
+	if (max_tc != adapter->hw_tcs) {
 		err = ixgbe_setup_tc(dev, max_tc);
 		if (err)
 			return err;

drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c

@@ -249,7 +249,7 @@ void ixgbe_dbg_adapter_init(struct ixgbe_adapter *adapter)
 
 /**
  * ixgbe_dbg_adapter_exit - clear out the adapter's debugfs entries
- * @pf: the pf that is stopping
+ * @adapter: the adapter that is exiting
  **/
 void ixgbe_dbg_adapter_exit(struct ixgbe_adapter *adapter)
 {

drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c

@@ -3117,7 +3117,7 @@ static int ixgbe_get_ts_info(struct net_device *dev,
 static unsigned int ixgbe_max_channels(struct ixgbe_adapter *adapter)
 {
 	unsigned int max_combined;
-	u8 tcs = netdev_get_num_tc(adapter->netdev);
+	u8 tcs = adapter->hw_tcs;
 
 	if (!(adapter->flags & IXGBE_FLAG_MSIX_ENABLED)) {
 		/* We only support one q_vector without MSI-X */
@@ -3174,7 +3174,7 @@ static void ixgbe_get_channels(struct net_device *dev,
 		return;
 
 	/* same thing goes for being DCB enabled */
-	if (netdev_get_num_tc(dev) > 1)
+	if (adapter->hw_tcs > 1)
 		return;
 
 	/* if ATR is disabled we can exit */
@@ -3220,7 +3220,7 @@ static int ixgbe_set_channels(struct net_device *dev,
 
 #endif
 	/* use setup TC to update any traffic class queue mapping */
-	return ixgbe_setup_tc(dev, netdev_get_num_tc(dev));
+	return ixgbe_setup_tc(dev, adapter->hw_tcs);
 }
 
 static int ixgbe_get_module_info(struct net_device *dev,

drivers/net/ethernet/intel/ixgbe/ixgbe_fcoe.c

@@ -150,6 +150,7 @@ int ixgbe_fcoe_ddp_put(struct net_device *netdev, u16 xid)
  * @xid: the exchange id requesting ddp
  * @sgl: the scatter-gather list for this request
  * @sgc: the number of scatter-gather items
+ * @target_mode: 1 to setup target mode, 0 to setup initiator mode
  *
  * Returns : 1 for success and 0 for no ddp
  */
@@ -1063,7 +1064,7 @@ int ixgbe_fcoe_get_hbainfo(struct net_device *netdev,
 
 /**
  * ixgbe_fcoe_get_tc - get the current TC that fcoe is mapped to
- * @adapter - pointer to the device adapter structure
+ * @adapter: pointer to the device adapter structure
  *
  * Return : TC that FCoE is mapped to
  */

drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c

@@ -46,8 +46,8 @@ static bool ixgbe_cache_ring_dcb_sriov(struct ixgbe_adapter *adapter)
 #endif /* IXGBE_FCOE */
 	struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ];
 	int i;
-	u16 reg_idx;
-	u8 tcs = netdev_get_num_tc(adapter->netdev);
+	u16 reg_idx, pool;
+	u8 tcs = adapter->hw_tcs;
 
 	/* verify we have DCB queueing enabled before proceeding */
 	if (tcs <= 1)
@@ -58,12 +58,16 @@ static bool ixgbe_cache_ring_dcb_sriov(struct ixgbe_adapter *adapter)
 		return false;
 
 	/* start at VMDq register offset for SR-IOV enabled setups */
+	pool = 0;
 	reg_idx = vmdq->offset * __ALIGN_MASK(1, ~vmdq->mask);
-	for (i = 0; i < adapter->num_rx_queues; i++, reg_idx++) {
+	for (i = 0, pool = 0; i < adapter->num_rx_queues; i++, reg_idx++) {
 		/* If we are greater than indices move to next pool */
-		if ((reg_idx & ~vmdq->mask) >= tcs)
+		if ((reg_idx & ~vmdq->mask) >= tcs) {
+			pool++;
 			reg_idx = __ALIGN_MASK(reg_idx, ~vmdq->mask);
+		}
 		adapter->rx_ring[i]->reg_idx = reg_idx;
+		adapter->rx_ring[i]->netdev = pool ? NULL : adapter->netdev;
 	}
 
 	reg_idx = vmdq->offset * __ALIGN_MASK(1, ~vmdq->mask);
@@ -92,6 +96,7 @@ static bool ixgbe_cache_ring_dcb_sriov(struct ixgbe_adapter *adapter)
 		for (i = fcoe->offset; i < adapter->num_rx_queues; i++) {
 			reg_idx = __ALIGN_MASK(reg_idx, ~vmdq->mask) + fcoe_tc;
 			adapter->rx_ring[i]->reg_idx = reg_idx;
+			adapter->rx_ring[i]->netdev = adapter->netdev;
 			reg_idx++;
 		}
 
@@ -111,9 +116,8 @@ static bool ixgbe_cache_ring_dcb_sriov(struct ixgbe_adapter *adapter)
 static void ixgbe_get_first_reg_idx(struct ixgbe_adapter *adapter, u8 tc,
 				    unsigned int *tx, unsigned int *rx)
 {
-	struct net_device *dev = adapter->netdev;
 	struct ixgbe_hw *hw = &adapter->hw;
-	u8 num_tcs = netdev_get_num_tc(dev);
+	u8 num_tcs = adapter->hw_tcs;
 
 	*tx = 0;
 	*rx = 0;
@@ -168,10 +172,9 @@ static void ixgbe_get_first_reg_idx(struct ixgbe_adapter *adapter, u8 tc,
  **/
 static bool ixgbe_cache_ring_dcb(struct ixgbe_adapter *adapter)
 {
-	struct net_device *dev = adapter->netdev;
+	u8 num_tcs = adapter->hw_tcs;
 	unsigned int tx_idx, rx_idx;
 	int tc, offset, rss_i, i;
-	u8 num_tcs = netdev_get_num_tc(dev);
 
 	/* verify we have DCB queueing enabled before proceeding */
 	if (num_tcs <= 1)
@@ -184,6 +187,7 @@ static bool ixgbe_cache_ring_dcb(struct ixgbe_adapter *adapter)
 		for (i = 0; i < rss_i; i++, tx_idx++, rx_idx++) {
 			adapter->tx_ring[offset + i]->reg_idx = tx_idx;
 			adapter->rx_ring[offset + i]->reg_idx = rx_idx;
+			adapter->rx_ring[offset + i]->netdev = adapter->netdev;
 			adapter->tx_ring[offset + i]->dcb_tc = tc;
 			adapter->rx_ring[offset + i]->dcb_tc = tc;
 		}
@@ -208,14 +212,15 @@ static bool ixgbe_cache_ring_sriov(struct ixgbe_adapter *adapter)
 #endif /* IXGBE_FCOE */
 	struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ];
 	struct ixgbe_ring_feature *rss = &adapter->ring_feature[RING_F_RSS];
+	u16 reg_idx, pool;
 	int i;
-	u16 reg_idx;
 
 	/* only proceed if VMDq is enabled */
 	if (!(adapter->flags & IXGBE_FLAG_VMDQ_ENABLED))
 		return false;
 
 	/* start at VMDq register offset for SR-IOV enabled setups */
+	pool = 0;
 	reg_idx = vmdq->offset * __ALIGN_MASK(1, ~vmdq->mask);
 	for (i = 0; i < adapter->num_rx_queues; i++, reg_idx++) {
 #ifdef IXGBE_FCOE
@@ -224,15 +229,20 @@ static bool ixgbe_cache_ring_sriov(struct ixgbe_adapter *adapter)
 			break;
 #endif
 		/* If we are greater than indices move to next pool */
-		if ((reg_idx & ~vmdq->mask) >= rss->indices)
+		if ((reg_idx & ~vmdq->mask) >= rss->indices) {
+			pool++;
 			reg_idx = __ALIGN_MASK(reg_idx, ~vmdq->mask);
+		}
 		adapter->rx_ring[i]->reg_idx = reg_idx;
+		adapter->rx_ring[i]->netdev = pool ? NULL : adapter->netdev;
 	}
 
 #ifdef IXGBE_FCOE
 	/* FCoE uses a linear block of queues so just assigning 1:1 */
-	for (; i < adapter->num_rx_queues; i++, reg_idx++)
+	for (; i < adapter->num_rx_queues; i++, reg_idx++) {
 		adapter->rx_ring[i]->reg_idx = reg_idx;
+		adapter->rx_ring[i]->netdev = adapter->netdev;
+	}
 
 #endif
 	reg_idx = vmdq->offset * __ALIGN_MASK(1, ~vmdq->mask);
@@ -269,8 +279,10 @@ static bool ixgbe_cache_ring_rss(struct ixgbe_adapter *adapter)
 {
 	int i, reg_idx;
 
-	for (i = 0; i < adapter->num_rx_queues; i++)
+	for (i = 0; i < adapter->num_rx_queues; i++) {
 		adapter->rx_ring[i]->reg_idx = i;
+		adapter->rx_ring[i]->netdev = adapter->netdev;
+	}
 	for (i = 0, reg_idx = 0; i < adapter->num_tx_queues; i++, reg_idx++)
 		adapter->tx_ring[i]->reg_idx = reg_idx;
 	for (i = 0; i < adapter->num_xdp_queues; i++, reg_idx++)
@@ -340,7 +352,7 @@ static bool ixgbe_set_dcb_sriov_queues(struct ixgbe_adapter *adapter)
 #ifdef IXGBE_FCOE
 	u16 fcoe_i = 0;
 #endif
-	u8 tcs = netdev_get_num_tc(adapter->netdev);
+	u8 tcs = adapter->hw_tcs;
 
 	/* verify we have DCB queueing enabled before proceeding */
 	if (tcs <= 1)
@@ -440,7 +452,7 @@ static bool ixgbe_set_dcb_queues(struct ixgbe_adapter *adapter)
 	int tcs;
 
 	/* Map queue offset and counts onto allocated tx queues */
-	tcs = netdev_get_num_tc(dev);
+	tcs = adapter->hw_tcs;
 
 	/* verify we have DCB queueing enabled before proceeding */
 	if (tcs <= 1)
@@ -607,6 +619,10 @@ static bool ixgbe_set_sriov_queues(struct ixgbe_adapter *adapter)
 	}
 
 #endif
+	/* populate TC0 for use by pool 0 */
+	netdev_set_tc_queue(adapter->netdev, 0,
+			    adapter->num_rx_queues_per_pool, 0);
+
 	return true;
 }
 
@@ -839,7 +855,7 @@ static int ixgbe_alloc_q_vector(struct ixgbe_adapter *adapter,
 	int node = NUMA_NO_NODE;
 	int cpu = -1;
 	int ring_count, size;
-	u8 tcs = netdev_get_num_tc(adapter->netdev);
+	u8 tcs = adapter->hw_tcs;
 
 	ring_count = txr_count + rxr_count + xdp_count;
 	size = sizeof(struct ixgbe_q_vector) +
@@ -922,11 +938,7 @@ static int ixgbe_alloc_q_vector(struct ixgbe_adapter *adapter,
 
 		/* apply Tx specific ring traits */
 		ring->count = adapter->tx_ring_count;
-		if (adapter->num_rx_pools > 1)
-			ring->queue_index =
-				txr_idx % adapter->num_rx_queues_per_pool;
-		else
-			ring->queue_index = txr_idx;
+		ring->queue_index = txr_idx;
 
 		/* assign ring to adapter */
 		adapter->tx_ring[txr_idx] = ring;
@@ -996,11 +1008,7 @@ static int ixgbe_alloc_q_vector(struct ixgbe_adapter *adapter,
 #endif /* IXGBE_FCOE */
 		/* apply Rx specific ring traits */
 		ring->count = adapter->rx_ring_count;
-		if (adapter->num_rx_pools > 1)
-			ring->queue_index =
-				rxr_idx % adapter->num_rx_queues_per_pool;
-		else
-			ring->queue_index = rxr_idx;
+		ring->queue_index = rxr_idx;
 
 		/* assign ring to adapter */
 		adapter->rx_ring[rxr_idx] = ring;
@@ -1176,7 +1184,7 @@ static void ixgbe_set_interrupt_capability(struct ixgbe_adapter *adapter)
 	 */
 
 	/* Disable DCB unless we only have a single traffic class */
-	if (netdev_get_num_tc(adapter->netdev) > 1) {
+	if (adapter->hw_tcs > 1) {
 		e_dev_warn("Number of DCB TCs exceeds number of available queues. Disabling DCB support.\n");
 		netdev_reset_tc(adapter->netdev);
 
@@ -1188,6 +1196,7 @@ static void ixgbe_set_interrupt_capability(struct ixgbe_adapter *adapter)
 		adapter->dcb_cfg.pfc_mode_enable = false;
 	}
 
+	adapter->hw_tcs = 0;
 	adapter->dcb_cfg.num_tcs.pg_tcs = 1;
 	adapter->dcb_cfg.num_tcs.pfc_tcs = 1;
 

drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c

@@ -378,7 +378,7 @@ static s32 ixgbe_get_phy_id(struct ixgbe_hw *hw)
 
 /**
  *  ixgbe_get_phy_type_from_id - Get the phy type
- *  @hw: pointer to hardware structure
+ *  @phy_id: hardware phy id
  *
  **/
 static enum ixgbe_phy_type ixgbe_get_phy_type_from_id(u32 phy_id)
@@ -489,6 +489,7 @@ s32 ixgbe_reset_phy_generic(struct ixgbe_hw *hw)
  *  the SWFW lock
  *  @hw: pointer to hardware structure
  *  @reg_addr: 32 bit address of PHY register to read
+ *  @device_type: 5 bit device type
  *  @phy_data: Pointer to read data from PHY register
  **/
 s32 ixgbe_read_phy_reg_mdi(struct ixgbe_hw *hw, u32 reg_addr, u32 device_type,
@@ -564,6 +565,7 @@ s32 ixgbe_read_phy_reg_mdi(struct ixgbe_hw *hw, u32 reg_addr, u32 device_type,
  *  using the SWFW lock - this function is needed in most cases
  *  @hw: pointer to hardware structure
  *  @reg_addr: 32 bit address of PHY register to read
+ *  @device_type: 5 bit device type
  *  @phy_data: Pointer to read data from PHY register
  **/
 s32 ixgbe_read_phy_reg_generic(struct ixgbe_hw *hw, u32 reg_addr,
@@ -763,6 +765,7 @@ s32 ixgbe_setup_phy_link_generic(struct ixgbe_hw *hw)
  *  ixgbe_setup_phy_link_speed_generic - Sets the auto advertised capabilities
  *  @hw: pointer to hardware structure
  *  @speed: new link speed
+ *  @autoneg_wait_to_complete: unused
  **/
 s32 ixgbe_setup_phy_link_speed_generic(struct ixgbe_hw *hw,
 				       ixgbe_link_speed speed,
@@ -861,6 +864,8 @@ s32 ixgbe_get_copper_link_capabilities_generic(struct ixgbe_hw *hw,
 /**
  *  ixgbe_check_phy_link_tnx - Determine link and speed status
  *  @hw: pointer to hardware structure
+ *  @speed: link speed
+ *  @link_up: status of link
  *
  *  Reads the VS1 register to determine if link is up and the current speed for
  *  the PHY.
@@ -1667,7 +1672,7 @@ s32 ixgbe_read_i2c_eeprom_generic(struct ixgbe_hw *hw, u8 byte_offset,
  *  ixgbe_read_i2c_sff8472_generic - Reads 8 bit word over I2C interface
  *  @hw: pointer to hardware structure
  *  @byte_offset: byte offset at address 0xA2
- *  @eeprom_data: value read
+ *  @sff8472_data: value read
  *
  *  Performs byte read operation to SFP module's SFF-8472 data over I2C
  **/
@@ -1714,6 +1719,7 @@ static bool ixgbe_is_sfp_probe(struct ixgbe_hw *hw, u8 offset, u8 addr)
  *  ixgbe_read_i2c_byte_generic_int - Reads 8 bit word over I2C
  *  @hw: pointer to hardware structure
  *  @byte_offset: byte offset to read
+ *  @dev_addr: device address
  *  @data: value read
  *  @lock: true if to take and release semaphore
  *
@@ -1804,6 +1810,7 @@ static s32 ixgbe_read_i2c_byte_generic_int(struct ixgbe_hw *hw, u8 byte_offset,
  *  ixgbe_read_i2c_byte_generic - Reads 8 bit word over I2C
  *  @hw: pointer to hardware structure
  *  @byte_offset: byte offset to read
+ *  @dev_addr: device address
  *  @data: value read
  *
  *  Performs byte read operation to SFP module's EEPROM over I2C interface at
@@ -1820,6 +1827,7 @@ s32 ixgbe_read_i2c_byte_generic(struct ixgbe_hw *hw, u8 byte_offset,
  *  ixgbe_read_i2c_byte_generic_unlocked - Reads 8 bit word over I2C
  *  @hw: pointer to hardware structure
  *  @byte_offset: byte offset to read
+ *  @dev_addr: device address
  *  @data: value read
  *
  *  Performs byte read operation to SFP module's EEPROM over I2C interface at
@@ -1836,6 +1844,7 @@ s32 ixgbe_read_i2c_byte_generic_unlocked(struct ixgbe_hw *hw, u8 byte_offset,
  *  ixgbe_write_i2c_byte_generic_int - Writes 8 bit word over I2C
  *  @hw: pointer to hardware structure
  *  @byte_offset: byte offset to write
+ *  @dev_addr: device address
  *  @data: value to write
  *  @lock: true if to take and release semaphore
  *
@@ -1904,6 +1913,7 @@ static s32 ixgbe_write_i2c_byte_generic_int(struct ixgbe_hw *hw, u8 byte_offset,
  *  ixgbe_write_i2c_byte_generic - Writes 8 bit word over I2C
  *  @hw: pointer to hardware structure
  *  @byte_offset: byte offset to write
+ *  @dev_addr: device address
  *  @data: value to write
  *
  *  Performs byte write operation to SFP module's EEPROM over I2C interface at
@@ -1920,6 +1930,7 @@ s32 ixgbe_write_i2c_byte_generic(struct ixgbe_hw *hw, u8 byte_offset,
  *  ixgbe_write_i2c_byte_generic_unlocked - Writes 8 bit word over I2C
  *  @hw: pointer to hardware structure
  *  @byte_offset: byte offset to write
+ *  @dev_addr: device address
  *  @data: value to write
  *
  *  Performs byte write operation to SFP module's EEPROM over I2C interface at

drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c

@@ -166,7 +166,7 @@
 
 /**
  * ixgbe_ptp_setup_sdp_x540
- * @hw: the hardware private structure
+ * @adapter: private adapter structure
  *
  * this function enables or disables the clock out feature on SDP0 for
  * the X540 device. It will create a 1second periodic output that can
@@ -299,7 +299,7 @@ static u64 ixgbe_ptp_read_82599(const struct cyclecounter *cc)
  * ixgbe_ptp_convert_to_hwtstamp - convert register value to hw timestamp
  * @adapter: private adapter structure
  * @hwtstamp: stack timestamp structure
- * @systim: unsigned 64bit system time value
+ * @timestamp: unsigned 64bit system time value
  *
  * We need to convert the adapter's RX/TXSTMP registers into a hwtstamp value
  * which can be used by the stack's ptp functions.
@@ -1015,7 +1015,7 @@ static int ixgbe_ptp_set_timestamp_mode(struct ixgbe_adapter *adapter,
 /**
  * ixgbe_ptp_set_ts_config - user entry point for timestamp mode
  * @adapter: pointer to adapter struct
- * @ifreq: ioctl data
+ * @ifr: ioctl data
  *
  * Set hardware to requested mode. If unsupported, return an error with no
  * changes. Otherwise, store the mode for future reference.
@@ -1338,7 +1338,7 @@ void ixgbe_ptp_init(struct ixgbe_adapter *adapter)
 
 /**
  * ixgbe_ptp_suspend - stop PTP work items
- * @ adapter: pointer to adapter struct
+ * @adapter: pointer to adapter struct
  *
  * this function suspends PTP activity, and prevents more PTP work from being
  * generated, but does not destroy the PTP clock device.

drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c

@@ -78,12 +78,9 @@ static int __ixgbe_enable_sriov(struct ixgbe_adapter *adapter,
 	struct ixgbe_hw *hw = &adapter->hw;
 	int i;
 
-	adapter->flags |= IXGBE_FLAG_SRIOV_ENABLED;
-
 	/* Enable VMDq flag so device will be set in VM mode */
-	adapter->flags |= IXGBE_FLAG_VMDQ_ENABLED;
-	if (!adapter->ring_feature[RING_F_VMDQ].limit)
-		adapter->ring_feature[RING_F_VMDQ].limit = 1;
+	adapter->flags |= IXGBE_FLAG_SRIOV_ENABLED |
+			  IXGBE_FLAG_VMDQ_ENABLED;
 
 	/* Allocate memory for per VF control structures */
 	adapter->vfinfo = kcalloc(num_vfs, sizeof(struct vf_data_storage),
@@ -314,7 +311,7 @@ static int ixgbe_pci_sriov_enable(struct pci_dev *dev, int num_vfs)
 	 * than we have available pools. The PCI bus driver already checks for
 	 * other values out of range.
 	 */
-	num_tc = netdev_get_num_tc(adapter->netdev);
+	num_tc = adapter->hw_tcs;
 	num_rx_pools = adapter->num_rx_pools;
 	limit = (num_tc > 4) ? IXGBE_MAX_VFS_8TC :
 		(num_tc > 1) ? IXGBE_MAX_VFS_4TC : IXGBE_MAX_VFS_1TC;
@@ -716,7 +713,7 @@ static inline void ixgbe_vf_reset_event(struct ixgbe_adapter *adapter, u32 vf)
 {
 	struct ixgbe_hw *hw = &adapter->hw;
 	struct vf_data_storage *vfinfo = &adapter->vfinfo[vf];
-	u8 num_tcs = netdev_get_num_tc(adapter->netdev);
+	u8 num_tcs = adapter->hw_tcs;
 
 	/* remove VLAN filters beloning to this VF */
 	ixgbe_clear_vf_vlans(adapter, vf);
@@ -924,7 +921,7 @@ static int ixgbe_set_vf_vlan_msg(struct ixgbe_adapter *adapter,
 {
 	u32 add = (msgbuf[0] & IXGBE_VT_MSGINFO_MASK) >> IXGBE_VT_MSGINFO_SHIFT;
 	u32 vid = (msgbuf[1] & IXGBE_VLVF_VLANID_MASK);
-	u8 tcs = netdev_get_num_tc(adapter->netdev);
+	u8 tcs = adapter->hw_tcs;
 
 	if (adapter->vfinfo[vf].pf_vlan || tcs) {
 		e_warn(drv,
@@ -1012,7 +1009,7 @@ static int ixgbe_get_vf_queues(struct ixgbe_adapter *adapter,
 	struct net_device *dev = adapter->netdev;
 	struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ];
 	unsigned int default_tc = 0;
-	u8 num_tcs = netdev_get_num_tc(dev);
+	u8 num_tcs = adapter->hw_tcs;
 
 	/* verify the PF is supporting the correct APIs */
 	switch (adapter->vfinfo[vf].vf_api) {

drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c

@@ -1642,10 +1642,12 @@ static s32 ixgbe_supported_sfp_modules_X550em(struct ixgbe_hw *hw, bool *linear)
 }
 
 /**
- *  ixgbe_setup_mac_link_sfp_x550em - Configure the KR PHY for SFP.
- *  @hw: pointer to hardware structure
+ * ixgbe_setup_mac_link_sfp_x550em - Configure the KR PHY for SFP.
+ * @hw: pointer to hardware structure
+ * @speed: the link speed to force
+ * @autoneg_wait_to_complete: unused
  *
- *  Configures the extern PHY and the integrated KR PHY for SFP support.
+ * Configures the extern PHY and the integrated KR PHY for SFP support.
  */
 static s32
 ixgbe_setup_mac_link_sfp_x550em(struct ixgbe_hw *hw,
@@ -1737,6 +1739,8 @@ static s32 ixgbe_setup_sfi_x550a(struct ixgbe_hw *hw, ixgbe_link_speed *speed)
 /**
  * ixgbe_setup_mac_link_sfp_n - Setup internal PHY for native SFP
  * @hw: pointer to hardware structure
+ * @speed: link speed
+ * @autoneg_wait_to_complete: unused
  *
  * Configure the the integrated PHY for native SFP support.
  */
@@ -1784,6 +1788,8 @@ ixgbe_setup_mac_link_sfp_n(struct ixgbe_hw *hw, ixgbe_link_speed speed,
 /**
  * ixgbe_setup_mac_link_sfp_x550a - Setup internal PHY for SFP
  * @hw: pointer to hardware structure
+ * @speed: link speed
+ * @autoneg_wait_to_complete: unused
  *
  * Configure the the integrated PHY for SFP support.
  */
@@ -1859,7 +1865,7 @@ ixgbe_setup_mac_link_sfp_x550a(struct ixgbe_hw *hw, ixgbe_link_speed speed,
  * ixgbe_setup_mac_link_t_X550em - Sets the auto advertised link speed
  * @hw: pointer to hardware structure
  * @speed: new link speed
- * @autoneg_wait_to_complete: true when waiting for completion is needed
+ * @autoneg_wait: true when waiting for completion is needed
  *
  * Setup internal/external PHY link speed based on link speed, then set
  * external PHY auto advertised link speed.
@@ -1943,6 +1949,8 @@ static s32 ixgbe_check_link_t_X550em(struct ixgbe_hw *hw,
 /**
  * ixgbe_setup_sgmii - Set up link for sgmii
  * @hw: pointer to hardware structure
+ * @speed: unused
+ * @autoneg_wait_to_complete: unused
  */
 static s32
 ixgbe_setup_sgmii(struct ixgbe_hw *hw, __always_unused ixgbe_link_speed speed,
@@ -2014,6 +2022,8 @@ ixgbe_setup_sgmii(struct ixgbe_hw *hw, __always_unused ixgbe_link_speed speed,
 /**
  * ixgbe_setup_sgmii_fw - Set up link for sgmii with firmware-controlled PHYs
  * @hw: pointer to hardware structure
+ * @speed: the link speed to force
+ * @autoneg_wait: true when waiting for completion is needed
  */
 static s32 ixgbe_setup_sgmii_fw(struct ixgbe_hw *hw, ixgbe_link_speed speed,
 				bool autoneg_wait)
@@ -3735,6 +3745,7 @@ static void ixgbe_release_swfw_sync_x550em_a(struct ixgbe_hw *hw, u32 mask)
  * ixgbe_read_phy_reg_x550a - Reads specified PHY register
  * @hw: pointer to hardware structure
  * @reg_addr: 32 bit address of PHY register to read
+ * @device_type: 5 bit device type
  * @phy_data: Pointer to read data from PHY register
  *
  * Reads a value from a specified PHY register using the SWFW lock and PHY

drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c

@@ -554,7 +554,6 @@ static void ixgbevf_process_skb_fields(struct ixgbevf_ring *rx_ring,
  * ixgbevf_is_non_eop - process handling of non-EOP buffers
  * @rx_ring: Rx ring being processed
  * @rx_desc: Rx descriptor for current buffer
- * @skb: current socket buffer containing buffer in progress
  *
  * This function updates next to clean.  If the buffer is an EOP buffer
  * this function exits returning false, otherwise it will place the
@@ -2741,7 +2740,7 @@ void ixgbevf_update_stats(struct ixgbevf_adapter *adapter)
 
 /**
  * ixgbevf_service_timer - Timer Call-back
- * @data: pointer to adapter cast into an unsigned long
+ * @t: pointer to timer_list struct
  **/
 static void ixgbevf_service_timer(struct timer_list *t)
 {
@@ -2884,7 +2883,7 @@ static void ixgbevf_watchdog_link_is_down(struct ixgbevf_adapter *adapter)
 
 /**
  * ixgbevf_watchdog_subtask - worker thread to bring link up
- * @work: pointer to work_struct containing our data
+ * @adapter: board private structure
  **/
 static void ixgbevf_watchdog_subtask(struct ixgbevf_adapter *adapter)
 {
@@ -4364,6 +4363,7 @@ static void __exit ixgbevf_exit_module(void)
 /**
  * ixgbevf_get_hw_dev_name - return device name string
  * used by hardware layer to print debugging information
+ * @hw: pointer to private hardware struct
  **/
 char *ixgbevf_get_hw_dev_name(struct ixgbe_hw *hw)
 {

drivers/net/ethernet/intel/ixgbevf/vf.c

@@ -146,6 +146,7 @@ static s32 ixgbevf_reset_hw_vf(struct ixgbe_hw *hw)
 /**
  * Hyper-V variant; the VF/PF communication is through the PCI
  * config space.
+ * @hw: pointer to private hardware struct
  */
 static s32 ixgbevf_hv_reset_hw_vf(struct ixgbe_hw *hw)
 {
@@ -303,7 +304,7 @@ static s32 ixgbevf_hv_set_uc_addr_vf(struct ixgbe_hw *hw, u32 index, u8 *addr)
 
 /**
  * ixgbevf_get_reta_locked - get the RSS redirection table (RETA) contents.
- * @adapter: pointer to the port handle
+ * @hw: pointer to hardware structure
  * @reta: buffer to fill with RETA contents.
  * @num_rx_queues: Number of Rx queues configured for this port
  *
@@ -536,6 +537,8 @@ static s32 ixgbevf_update_mc_addr_list_vf(struct ixgbe_hw *hw,
 
 /**
  * Hyper-V variant - just a stub.
+ * @hw: unused
+ * @netdev: unused
  */
 static s32 ixgbevf_hv_update_mc_addr_list_vf(struct ixgbe_hw *hw,
 					     struct net_device *netdev)
@@ -584,6 +587,8 @@ static s32 ixgbevf_update_xcast_mode(struct ixgbe_hw *hw, int xcast_mode)
 
 /**
  * Hyper-V variant - just a stub.
+ * @hw: unused
+ * @xcast_mode: unused
  */
 static s32 ixgbevf_hv_update_xcast_mode(struct ixgbe_hw *hw, int xcast_mode)
 {
@@ -626,6 +631,10 @@ static s32 ixgbevf_set_vfta_vf(struct ixgbe_hw *hw, u32 vlan, u32 vind,
 
 /**
  * Hyper-V variant - just a stub.
+ * @hw: unused
+ * @vlan: unused
+ * @vind: unused
+ * @vlan_on: unused
  */
 static s32 ixgbevf_hv_set_vfta_vf(struct ixgbe_hw *hw, u32 vlan, u32 vind,
 				  bool vlan_on)
@@ -655,7 +664,7 @@ static s32 ixgbevf_setup_mac_link_vf(struct ixgbe_hw *hw,
  *  @hw: pointer to hardware structure
  *  @speed: pointer to link speed
  *  @link_up: true is link is up, false otherwise
- *  @autoneg_wait_to_complete: true when waiting for completion is needed
+ *  @autoneg_wait_to_complete: unused
  *
  *  Reads the links register to determine if link is up and the current speed
  **/
@@ -740,6 +749,10 @@ static s32 ixgbevf_check_mac_link_vf(struct ixgbe_hw *hw,
 
 /**
  * Hyper-V variant; there is no mailbox communication.
+ * @hw: pointer to private hardware struct
+ * @speed: pointer to link speed
+ * @link_up: true is link is up, false otherwise
+ * @autoneg_wait_to_complete: unused
  */
 static s32 ixgbevf_hv_check_mac_link_vf(struct ixgbe_hw *hw,
 					ixgbe_link_speed *speed,

net/core/dev.c

@@ -3420,8 +3420,7 @@ struct netdev_queue *netdev_pick_tx(struct net_device *dev,
 		else
 			queue_index = __netdev_pick_tx(dev, skb);
 
-		if (!accel_priv)
-			queue_index = netdev_cap_txqueue(dev, queue_index);
+		queue_index = netdev_cap_txqueue(dev, queue_index);
 	}
 
 	skb_set_queue_mapping(skb, queue_index);