iio:pressure: device settings are set immediately during probe

This patch set pressure settings right after probe start. This is
done in preparation of regmap that needs different configuration
based on multiread bit value.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

drivers/iio/pressure/st_pressure_i2c.c

@@ -78,18 +78,13 @@ static const struct i2c_device_id st_press_id_table[] = {
 MODULE_DEVICE_TABLE(i2c, st_press_id_table);
 
 static int st_press_i2c_probe(struct i2c_client *client,
-						const struct i2c_device_id *id)
+			      const struct i2c_device_id *id)
 {
-	struct iio_dev *indio_dev;
+	const struct st_sensor_settings *settings;
 	struct st_sensor_data *press_data;
+	struct iio_dev *indio_dev;
 	int ret;
 
-	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*press_data));
-	if (!indio_dev)
-		return -ENOMEM;
-
-	press_data = iio_priv(indio_dev);
-
 	if (client->dev.of_node) {
 		st_sensors_of_name_probe(&client->dev, st_press_of_match,
 					 client->name, sizeof(client->name));
@@ -99,10 +94,24 @@ static int st_press_i2c_probe(struct i2c_client *client,
 			return -ENODEV;
 
 		strlcpy(client->name, st_press_id_table[ret].name,
-				sizeof(client->name));
+			sizeof(client->name));
 	} else if (!id)
 		return -ENODEV;
 
+	settings = st_press_get_settings(client->name);
+	if (!settings) {
+		dev_err(&client->dev, "device name %s not recognized.\n",
+			client->name);
+		return -ENODEV;
+	}
+
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*press_data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	press_data = iio_priv(indio_dev);
+	press_data->sensor_settings = (struct st_sensor_settings *)settings;
+
 	st_sensors_i2c_configure(indio_dev, client, press_data);
 
 	ret = st_press_common_probe(indio_dev);

drivers/iio/pressure/st_pressure_spi.c

@@ -61,18 +61,28 @@ MODULE_DEVICE_TABLE(of, st_press_of_match);
 
 static int st_press_spi_probe(struct spi_device *spi)
 {
-	struct iio_dev *indio_dev;
+	const struct st_sensor_settings *settings;
 	struct st_sensor_data *press_data;
+	struct iio_dev *indio_dev;
 	int err;
 
+	st_sensors_of_name_probe(&spi->dev, st_press_of_match,
+				 spi->modalias, sizeof(spi->modalias));
+
+	settings = st_press_get_settings(spi->modalias);
+	if (!settings) {
+		dev_err(&spi->dev, "device name %s not recognized.\n",
+			spi->modalias);
+		return -ENODEV;
+	}
+
 	indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*press_data));
-	if (indio_dev == NULL)
+	if (!indio_dev)
 		return -ENOMEM;
 
 	press_data = iio_priv(indio_dev);
+	press_data->sensor_settings = (struct st_sensor_settings *)settings;
 
-	st_sensors_of_name_probe(&spi->dev, st_press_of_match,
-				 spi->modalias, sizeof(spi->modalias));
 	st_sensors_spi_configure(indio_dev, spi, press_data);
 
 	err = st_press_common_probe(indio_dev);