Commit 573cfde7 authored by Nick Kossifidis's avatar Nick Kossifidis Committed by John W. Linville

ath5k: Fix fast channel switching

Fast channel change fixes:

a) Always set OFDM timings
b) Don't re-activate PHY
c) Enable only NF calibration, not AGC

https://bugzilla.kernel.org/show_bug.cgi?id=27382Signed-off-by: default avatarNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
parent 28bec7b8
......@@ -282,6 +282,34 @@ int ath5k_hw_phy_disable(struct ath5k_hw *ah)
return 0;
}
/*
* Wait for synth to settle
*/
static void ath5k_hw_wait_for_synth(struct ath5k_hw *ah,
struct ieee80211_channel *channel)
{
/*
* On 5211+ read activation -> rx delay
* and use it (100ns steps).
*/
if (ah->ah_version != AR5K_AR5210) {
u32 delay;
delay = ath5k_hw_reg_read(ah, AR5K_PHY_RX_DELAY) &
AR5K_PHY_RX_DELAY_M;
delay = (channel->hw_value & CHANNEL_CCK) ?
((delay << 2) / 22) : (delay / 10);
if (ah->ah_bwmode == AR5K_BWMODE_10MHZ)
delay = delay << 1;
if (ah->ah_bwmode == AR5K_BWMODE_5MHZ)
delay = delay << 2;
/* XXX: /2 on turbo ? Let's be safe
* for now */
udelay(100 + delay);
} else {
mdelay(1);
}
}
/**********************\
* RF Gain optimization *
......@@ -3238,6 +3266,13 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,
/* Failed */
if (i >= 100)
return -EIO;
/* Set channel and wait for synth */
ret = ath5k_hw_channel(ah, channel);
if (ret)
return ret;
ath5k_hw_wait_for_synth(ah, channel);
}
/*
......@@ -3252,13 +3287,53 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,
if (ret)
return ret;
/* Write OFDM timings on 5212*/
if (ah->ah_version == AR5K_AR5212 &&
channel->hw_value & CHANNEL_OFDM) {
ret = ath5k_hw_write_ofdm_timings(ah, channel);
if (ret)
return ret;
/* Spur info is available only from EEPROM versions
* greater than 5.3, but the EEPROM routines will use
* static values for older versions */
if (ah->ah_mac_srev >= AR5K_SREV_AR5424)
ath5k_hw_set_spur_mitigation_filter(ah,
channel);
}
/* If we used fast channel switching
* we are done, release RF bus and
* fire up NF calibration.
*
* Note: Only NF calibration due to
* channel change, not AGC calibration
* since AGC is still running !
*/
if (fast) {
/*
* Release RF Bus grant
*/
AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_RFBUS_REQ,
AR5K_PHY_RFBUS_REQ_REQUEST);
/*
* Start NF calibration
*/
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL,
AR5K_PHY_AGCCTL_NF);
return ret;
}
/*
* For 5210 we do all initialization using
* initvals, so we don't have to modify
* any settings (5210 also only supports
* a/aturbo modes)
*/
if ((ah->ah_version != AR5K_AR5210) && !fast) {
if (ah->ah_version != AR5K_AR5210) {
/*
* Write initial RF gain settings
......@@ -3277,22 +3352,6 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,
if (ret)
return ret;
/* Write OFDM timings on 5212*/
if (ah->ah_version == AR5K_AR5212 &&
channel->hw_value & CHANNEL_OFDM) {
ret = ath5k_hw_write_ofdm_timings(ah, channel);
if (ret)
return ret;
/* Spur info is available only from EEPROM versions
* greater than 5.3, but the EEPROM routines will use
* static values for older versions */
if (ah->ah_mac_srev >= AR5K_SREV_AR5424)
ath5k_hw_set_spur_mitigation_filter(ah,
channel);
}
/*Enable/disable 802.11b mode on 5111
(enable 2111 frequency converter + CCK)*/
if (ah->ah_radio == AR5K_RF5111) {
......@@ -3323,47 +3382,20 @@ int ath5k_hw_phy_init(struct ath5k_hw *ah, struct ieee80211_channel *channel,
*/
ath5k_hw_reg_write(ah, AR5K_PHY_ACT_ENABLE, AR5K_PHY_ACT);
ath5k_hw_wait_for_synth(ah, channel);
/*
* On 5211+ read activation -> rx delay
* and use it.
* Perform ADC test to see if baseband is ready
* Set tx hold and check adc test register
*/
if (ah->ah_version != AR5K_AR5210) {
u32 delay;
delay = ath5k_hw_reg_read(ah, AR5K_PHY_RX_DELAY) &
AR5K_PHY_RX_DELAY_M;
delay = (channel->hw_value & CHANNEL_CCK) ?
((delay << 2) / 22) : (delay / 10);
if (ah->ah_bwmode == AR5K_BWMODE_10MHZ)
delay = delay << 1;
if (ah->ah_bwmode == AR5K_BWMODE_5MHZ)
delay = delay << 2;
/* XXX: /2 on turbo ? Let's be safe
* for now */
udelay(100 + delay);
} else {
mdelay(1);
}
if (fast)
/*
* Release RF Bus grant
*/
AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_RFBUS_REQ,
AR5K_PHY_RFBUS_REQ_REQUEST);
else {
/*
* Perform ADC test to see if baseband is ready
* Set tx hold and check adc test register
*/
phy_tst1 = ath5k_hw_reg_read(ah, AR5K_PHY_TST1);
ath5k_hw_reg_write(ah, AR5K_PHY_TST1_TXHOLD, AR5K_PHY_TST1);
for (i = 0; i <= 20; i++) {
if (!(ath5k_hw_reg_read(ah, AR5K_PHY_ADC_TEST) & 0x10))
break;
udelay(200);
}
ath5k_hw_reg_write(ah, phy_tst1, AR5K_PHY_TST1);
phy_tst1 = ath5k_hw_reg_read(ah, AR5K_PHY_TST1);
ath5k_hw_reg_write(ah, AR5K_PHY_TST1_TXHOLD, AR5K_PHY_TST1);
for (i = 0; i <= 20; i++) {
if (!(ath5k_hw_reg_read(ah, AR5K_PHY_ADC_TEST) & 0x10))
break;
udelay(200);
}
ath5k_hw_reg_write(ah, phy_tst1, AR5K_PHY_TST1);
/*
* Start automatic gain control calibration
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment