Commit 5a2cc190 authored by Jeff Kirsher's avatar Jeff Kirsher

mlx4: Move the Mellanox driver

Moves the Mellanox driver into drivers/net/ethernet/mellanox/ and
make the necessary Kconfig and Makefile changes.

CC: Roland Dreier <roland@kernel.org>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
parent f844a0ea
......@@ -1554,30 +1554,6 @@ config PASEMI_MAC
This driver supports the on-chip 1/10Gbit Ethernet controller on
PA Semi's PWRficient line of chips.
config MLX4_EN
tristate "Mellanox Technologies 10Gbit Ethernet support"
depends on PCI && INET
select MLX4_CORE
select INET_LRO
help
This driver supports Mellanox Technologies ConnectX Ethernet
devices.
config MLX4_CORE
tristate
depends on PCI
default n
config MLX4_DEBUG
bool "Verbose debugging output" if (MLX4_CORE && EXPERT)
depends on MLX4_CORE
default y
---help---
This option causes debugging code to be compiled into the
mlx4_core driver. The output can be turned on via the
debug_level module parameter (which can also be set after
the driver is loaded through sysfs).
config TEHUTI
tristate "Tehuti Networks 10G Ethernet"
depends on PCI
......
......@@ -157,7 +157,6 @@ obj-$(CONFIG_BFIN_MAC) += bfin_mac.o
obj-$(CONFIG_DM9000) += dm9000.o
obj-$(CONFIG_PASEMI_MAC) += pasemi_mac_driver.o
pasemi_mac_driver-objs := pasemi_mac.o pasemi_mac_ethtool.o
obj-$(CONFIG_MLX4_CORE) += mlx4/
obj-$(CONFIG_ENC28J60) += enc28j60.o
obj-$(CONFIG_ETHOC) += ethoc.o
obj-$(CONFIG_GRETH) += greth.o
......
......@@ -20,6 +20,7 @@ source "drivers/net/ethernet/chelsio/Kconfig"
source "drivers/net/ethernet/emulex/Kconfig"
source "drivers/net/ethernet/intel/Kconfig"
source "drivers/net/ethernet/i825xx/Kconfig"
source "drivers/net/ethernet/mellanox/Kconfig"
source "drivers/net/ethernet/qlogic/Kconfig"
source "drivers/net/ethernet/racal/Kconfig"
source "drivers/net/ethernet/sfc/Kconfig"
......
......@@ -11,6 +11,7 @@ obj-$(CONFIG_NET_VENDOR_CHELSIO) += chelsio/
obj-$(CONFIG_NET_VENDOR_EMULEX) += emulex/
obj-$(CONFIG_NET_VENDOR_INTEL) += intel/
obj-$(CONFIG_NET_VENDOR_I825XX) += i825xx/
obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/
obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
obj-$(CONFIG_NET_VENDOR_RACAL) += racal/
obj-$(CONFIG_SFC) += sfc/
......
#
# Mellanox driver configuration
#
config NET_VENDOR_MELLANOX
bool "Mellanox devices"
depends on PCI && INET
---help---
If you have a network (Ethernet) card belonging to this class, say Y
and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
Note that the answer to this question doesn't directly affect the
kernel: saying N will just cause the configurator to skip all
the questions about Mellanox cards. If you say Y, you will be asked
for your specific card in the following questions.
if NET_VENDOR_MELLANOX
source "drivers/net/ethernet/mellanox/mlx4/Kconfig"
endif # NET_VENDOR_MELLANOX
#
# Makefile for the Mellanox device drivers.
#
obj-$(CONFIG_MLX4_CORE) += mlx4/
#
# Mellanox driver configuration
#
config MLX4_EN
tristate "Mellanox Technologies 10Gbit Ethernet support"
depends on PCI && INET
select MLX4_CORE
select INET_LRO
---help---
This driver supports Mellanox Technologies ConnectX Ethernet
devices.
config MLX4_CORE
tristate
depends on PCI
default n
config MLX4_DEBUG
bool "Verbose debugging output" if (MLX4_CORE && EXPERT)
depends on MLX4_CORE
default y
---help---
This option causes debugging code to be compiled into the
mlx4_core driver. The output can be turned on via the
debug_level module parameter (which can also be set after
the driver is loaded through sysfs).
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment