Commit 5d4c3cfb authored by Eugen Hristev's avatar Eugen Hristev Committed by Alexandre Belloni

ARM: dts: at91: sama5d27_wlsom1: add SAMA5D27 wlsom1 and wlsom1-ek

This is the addition of a new Evaluation Kit the SAMA5D27-WLSOM1-EK.
It's based on the Microchip WireLess SoM which contains the
SAMA5D27 LPDDR2 2Gbits SiP.

[nicolas.ferre@microchip.com]: initial implementation
Signed-off-by: default avatarNicolas Ferre <nicolas.ferre@microchip.com>
[eugen.hristev@microchip.com]: ported to new kernel version,
[eugen.hristev@microchip.com]: addition of peripherals (adc, pmic, qspi, uart)
Signed-off-by: default avatarEugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/1573543139-8533-4-git-send-email-eugen.hristev@microchip.comSigned-off-by: default avatarAlexandre Belloni <alexandre.belloni@bootlin.com>
parent c963e34f
...@@ -49,6 +49,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \ ...@@ -49,6 +49,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox3-hs.dtb \ at91-kizbox3-hs.dtb \
at91-nattis-2-natte-2.dtb \ at91-nattis-2-natte-2.dtb \
at91-sama5d27_som1_ek.dtb \ at91-sama5d27_som1_ek.dtb \
at91-sama5d27_wlsom1_ek.dtb \
at91-sama5d2_ptc_ek.dtb \ at91-sama5d2_ptc_ek.dtb \
at91-sama5d2_xplained.dtb \ at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \ at91-sama5d3_xplained.dtb \
......
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* at91-sama5d27_wlsom1.dtsi - Device Tree file for SAMA5D27 WLSOM1
*
* Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
*
* Author: Nicolas Ferre <nicolas.ferre@microcihp.com>
* Author: Eugen Hristev <eugen.hristev@microcihp.com>
*/
#include "sama5d2.dtsi"
#include "sama5d2-pinfunc.h"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/mfd/atmel-flexcom.h>
#include <dt-bindings/pinctrl/at91.h>
/ {
model = "Microchip SAMA5D27 WLSOM1";
compatible = "microchip,sama5d27-wlsom1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
clocks {
slow_xtal {
clock-frequency = <32768>;
};
main_xtal {
clock-frequency = <24000000>;
};
};
};
&flx1 {
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
uart6: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(13))>,
<&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(14))>;
dma-names = "tx", "rx";
clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
clock-names = "usart";
pinctrl-0 = <&pinctrl_flx1_default>;
pinctrl-names = "default";
};
};
&i2c0 {
pinctrl-0 = <&pinctrl_i2c0_default>;
pinctrl-names = "default";
status = "okay";
};
&i2c1 {
dmas = <0>, <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1_default>;
status = "okay";
mcp16502@5b {
compatible = "microchip,mcp16502";
reg = <0x5b>;
status = "okay";
lpm-gpios = <&pioBU 0 GPIO_ACTIVE_LOW>;
regulators {
vdd_3v3: VDD_IO {
regulator-name = "VDD_IO";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <3700000>;
regulator-initial-mode = <2>;
regulator-allowed-modes = <2>, <4>;
regulator-always-on;
regulator-state-standby {
regulator-on-in-suspend;
regulator-mode = <4>;
};
regulator-state-mem {
regulator-off-in-suspend;
regulator-mode = <4>;
};
};
vddio_ddr: VDD_DDR {
regulator-name = "VDD_DDR";
regulator-min-microvolt = <600000>;
regulator-max-microvolt = <1850000>;
regulator-initial-mode = <2>;
regulator-allowed-modes = <2>, <4>;
regulator-always-on;
regulator-state-standby {
regulator-on-in-suspend;
regulator-suspend-microvolt = <1200000>;
regulator-changeable-in-suspend;
regulator-mode = <4>;
};
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <1200000>;
regulator-changeable-in-suspend;
regulator-mode = <4>;
};
};
vdd_core: VDD_CORE {
regulator-name = "VDD_CORE";
regulator-min-microvolt = <600000>;
regulator-max-microvolt = <1850000>;
regulator-initial-mode = <2>;
regulator-allowed-modes = <2>, <4>;
regulator-always-on;
regulator-state-standby {
regulator-on-in-suspend;
regulator-mode = <4>;
};
regulator-state-mem {
regulator-off-in-suspend;
regulator-mode = <4>;
};
};
vdd_ddr: VDD_OTHER {
regulator-name = "VDD_OTHER";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <2>;
regulator-allowed-modes = <2>, <4>;
regulator-always-on;
regulator-state-standby {
regulator-on-in-suspend;
regulator-suspend-microvolt = <1800000>;
regulator-changeable-in-suspend;
regulator-mode = <4>;
};
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <1800000>;
regulator-changeable-in-suspend;
regulator-mode = <4>;
};
};
LDO1 {
regulator-name = "LDO1";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <3700000>;
regulator-always-on;
regulator-state-standby {
regulator-on-in-suspend;
};
regulator-state-mem {
regulator-off-in-suspend;
};
};
LDO2 {
regulator-name = "LDO2";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <3700000>;
regulator-always-on;
regulator-state-standby {
regulator-on-in-suspend;
};
regulator-state-mem {
regulator-off-in-suspend;
};
};
};
};
};
&macb0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_macb0_default>;
phy-mode = "rmii";
ethernet-phy@0 {
reg = <0x0>;
interrupt-parent = <&pioA>;
interrupts = <PIN_PB24 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_macb0_phy_irq>;
};
};
&pmc {
atmel,osc-bypass;
};
&qspi1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_qspi1_default>;
status = "disabled";
qspi1_flash: spi_flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <80000000>;
spi-rx-bus-width = <4>;
spi-tx-bus-width = <4>;
m25p,fast-read;
status = "disabled";
at91bootstrap@0 {
label = "at91bootstrap";
reg = <0x0 0x40000>;
};
bootloader@40000 {
label = "bootloader";
reg = <0x40000 0xc0000>;
};
bootloaderenvred@100000 {
label = "bootloader env redundant";
reg = <0x100000 0x40000>;
};
bootloaderenv@140000 {
label = "bootloader env";
reg = <0x140000 0x40000>;
};
dtb@180000 {
label = "device tree";
reg = <0x180000 0x80000>;
};
kernel@200000 {
label = "kernel";
reg = <0x200000 0x600000>;
};
};
};
&pioA {
pinctrl_flx1_default: flx1_usart_default {
pinmux = <PIN_PA24__FLEXCOM1_IO0>,
<PIN_PA23__FLEXCOM1_IO1>,
<PIN_PA25__FLEXCOM1_IO3>,
<PIN_PA26__FLEXCOM1_IO4>;
bias-disable;
};
pinctrl_i2c0_default: i2c0_default {
pinmux = <PIN_PD21__TWD0>,
<PIN_PD22__TWCK0>;
bias-disable;
};
pinctrl_i2c1_default: i2c1_default {
pinmux = <PIN_PD19__TWD1>,
<PIN_PD20__TWCK1>;
bias-disable;
};
pinctrl_macb0_default: macb0_default {
pinmux = <PIN_PB14__GTXCK>,
<PIN_PB15__GTXEN>,
<PIN_PB16__GRXDV>,
<PIN_PB17__GRXER>,
<PIN_PB18__GRX0>,
<PIN_PB19__GRX1>,
<PIN_PB20__GTX0>,
<PIN_PB21__GTX1>,
<PIN_PB22__GMDC>,
<PIN_PB23__GMDIO>;
bias-disable;
};
pinctrl_macb0_phy_irq: macb0_phy_irq {
pinmux = <PIN_PB24__GPIO>;
bias-disable;
};
pinctrl_qspi1_default: qspi1_default {
pinmux = <PIN_PB5__QSPI1_SCK>,
<PIN_PB6__QSPI1_CS>,
<PIN_PB7__QSPI1_IO0>,
<PIN_PB8__QSPI1_IO1>,
<PIN_PB9__QSPI1_IO2>,
<PIN_PB10__QSPI1_IO3>;
bias-pull-up;
};
};
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* at91-sama5d27_wlsom1_ek.dts - Device Tree file for SAMA5D27 WLSOM1 EK
*
* Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
*
* Author: Nicolas Ferre <nicolas.ferre@microcihp.com>
*/
/dts-v1/;
#include "at91-sama5d27_wlsom1.dtsi"
/ {
model = "Microchip SAMA5D27 WLSOM1 EK";
compatible = "microchip,sama5d27-wlsom1-ek", "microchip,sama5d27-wlsom1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
aliases {
serial0 = &uart0; /* DBGU */
serial1 = &uart6; /* BT */
serial2 = &uart5; /* mikro BUS 2 */
serial3 = &uart3; /* mikro BUS 1 */
i2c1 = &i2c1;
};
chosen {
stdout-path = "serial0:115200n8";
};
gpio_keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_key_gpio_default>;
status = "okay";
sw4 {
label = "USER BUTTON";
gpios = <&pioA PIN_PB2 GPIO_ACTIVE_LOW>;
linux,code = <0x104>;
wakeup-source;
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_led_gpio_default>;
status = "okay";
red {
label = "red";
gpios = <&pioA PIN_PA6 GPIO_ACTIVE_HIGH>;
};
green {
label = "green";
gpios = <&pioA PIN_PA7 GPIO_ACTIVE_HIGH>;
};
blue {
label = "blue";
gpios = <&pioA PIN_PA8 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
};
&adc {
vddana-supply = <&vdd_3v3>;
vref-supply = <&vdd_3v3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_adc_default>;
status = "okay";
};
&flx0 {
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
status = "okay";
uart5: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(11))>,
<&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(12))>;
dma-names = "tx", "rx";
clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
clock-names = "usart";
pinctrl-0 = <&pinctrl_flx0_default>;
pinctrl-names = "default";
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "okay";
};
};
&flx1 {
status = "okay";
uart6: serial@200 {
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "okay";
};
};
&macb0 {
status = "okay";
};
&pioA {
/*
* There is no real pinmux for ADC, if the pin
* is not requested by another peripheral then
* the muxing is done when channel is enabled.
* Requesting pins for ADC is GPIO is
* encouraged to prevent conflicts and to
* disable bias in order to be in the same
* state when the pin is not muxed to the adc.
*/
pinctrl_adc_default: adc_default {
pinmux = <PIN_PD25__GPIO>,
<PIN_PD26__GPIO>;
bias-disable;
};
pinctrl_flx0_default: flx0_usart_default {
pinmux = <PIN_PB28__FLEXCOM0_IO0>,
<PIN_PB29__FLEXCOM0_IO1>;
bias-disable;
};
pinctrl_key_gpio_default: key_gpio_default {
pinmux = <PIN_PB2__GPIO>;
bias-pull-up;
};
pinctrl_led_gpio_default: led_gpio_default {
pinmux = <PIN_PA6__GPIO>,
<PIN_PA7__GPIO>,
<PIN_PA8__GPIO>;
bias-pull-down;
};
pinctrl_sdmmc0_default: sdmmc0_default {
cmd_data {
pinmux = <PIN_PA1__SDMMC0_CMD>,
<PIN_PA2__SDMMC0_DAT0>,
<PIN_PA3__SDMMC0_DAT1>,
<PIN_PA4__SDMMC0_DAT2>,
<PIN_PA5__SDMMC0_DAT3>;
bias-disable;
};
ck_cd_vddsel {
pinmux = <PIN_PA0__SDMMC0_CK>,
<PIN_PA11__SDMMC0_VDDSEL>,
<PIN_PA12__SDMMC0_WP>,
<PIN_PA13__SDMMC0_CD>;
bias-disable;
};
};
pinctrl_uart0_default: uart0_default {
pinmux = <PIN_PB26__URXD0>,
<PIN_PB27__UTXD0>;
bias-disable;
};
pinctrl_uart3_default: uart3_default {
pinmux = <PIN_PB11__URXD3>,
<PIN_PB12__UTXD3>;
bias-disable;
};
pinctrl_pwm0_default: pwm0_default {
pinmux = <PIN_PA31__PWML0>,
<PIN_PA30__PWMH0>;
bias-disable;
};
pinctrl_usb_default: usb_default {
pinmux = <PIN_PA10__GPIO>;
bias-disable;
};
};
&pwm0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm0_default>;
status = "okay";
};
&qspi1 {
status = "okay";
qspi1_flash: spi_flash@0 {
status = "okay";
};
};
&sdmmc0 {
bus-width = <4>;
mmc-ddr-3_3v;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc0_default>;
status = "okay";
};
&shutdown_controller {
atmel,shdwc-debouncer = <976>;
atmel,wakeup-rtc-timer;
input@0 {
reg = <0>;
atmel,wakeup-type = "low";
};
};
&tcb0 {
timer0: timer@0 {
compatible = "atmel,tcb-timer";
reg = <0>;
};
timer1: timer@1 {
compatible = "atmel,tcb-timer";
reg = <1>;
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0_default>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3_default>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "okay";
};
&usb1 {
num-ports = <3>;
atmel,vbus-gpio = <0
&pioA PIN_PA10 GPIO_ACTIVE_HIGH
0
>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb_default>;
status = "okay";
};
&usb2 {
phy_type = "hsic";
status = "okay";
};
&watchdog {
status = "okay";
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment