[ARM] msm: Update list of proc_comm enums.

Signed-off-by: Dima Zavin <dima@android.com>

arch/arm/mach-msm/proc_comm.h

@@ -62,19 +62,104 @@ enum {
 	PCOM_RESET_CHIP_IMM,
 	PCOM_PM_VID_EN,
 	PCOM_VREG_PULLDOWN,
+	PCOM_GET_MODEM_VERSION,
+	PCOM_CLK_REGIME_SEC_RESET,
+	PCOM_CLK_REGIME_SEC_RESET_ASSERT,
+	PCOM_CLK_REGIME_SEC_RESET_DEASSERT,
+	PCOM_CLK_REGIME_SEC_PLL_REQUEST_WRP,
+	PCOM_CLK_REGIME_SEC_ENABLE,
+	PCOM_CLK_REGIME_SEC_DISABLE,
+	PCOM_CLK_REGIME_SEC_IS_ON,
+	PCOM_CLK_REGIME_SEC_SEL_CLK_INV,
+	PCOM_CLK_REGIME_SEC_SEL_CLK_SRC,
+	PCOM_CLK_REGIME_SEC_SEL_CLK_DIV,
+	PCOM_CLK_REGIME_SEC_ICODEC_CLK_ENABLE,
+	PCOM_CLK_REGIME_SEC_ICODEC_CLK_DISABLE,
+	PCOM_CLK_REGIME_SEC_SEL_SPEED,
+	PCOM_CLK_REGIME_SEC_CONFIG_GP_CLK_WRP,
+	PCOM_CLK_REGIME_SEC_CONFIG_MDH_CLK_WRP,
+	PCOM_CLK_REGIME_SEC_USB_XTAL_ON,
+	PCOM_CLK_REGIME_SEC_USB_XTAL_OFF,
+	PCOM_CLK_REGIME_SEC_SET_QDSP_DME_MODE,
+	PCOM_CLK_REGIME_SEC_SWITCH_ADSP_CLK,
+	PCOM_CLK_REGIME_SEC_GET_MAX_ADSP_CLK_KHZ,
+	PCOM_CLK_REGIME_SEC_GET_I2C_CLK_KHZ,
+	PCOM_CLK_REGIME_SEC_MSM_GET_CLK_FREQ_KHZ,
+	PCOM_CLK_REGIME_SEC_SEL_VFE_SRC,
+	PCOM_CLK_REGIME_SEC_MSM_SEL_CAMCLK,
+	PCOM_CLK_REGIME_SEC_MSM_SEL_LCDCLK,
+	PCOM_CLK_REGIME_SEC_VFE_RAIL_OFF,
+	PCOM_CLK_REGIME_SEC_VFE_RAIL_ON,
+	PCOM_CLK_REGIME_SEC_GRP_RAIL_OFF,
+	PCOM_CLK_REGIME_SEC_GRP_RAIL_ON,
+	PCOM_CLK_REGIME_SEC_VDC_RAIL_OFF,
+	PCOM_CLK_REGIME_SEC_VDC_RAIL_ON,
+	PCOM_CLK_REGIME_SEC_LCD_CTRL,
+	PCOM_CLK_REGIME_SEC_REGISTER_FOR_CPU_RESOURCE,
+	PCOM_CLK_REGIME_SEC_DEREGISTER_FOR_CPU_RESOURCE,
+	PCOM_CLK_REGIME_SEC_RESOURCE_REQUEST_WRP,
+	PCOM_CLK_REGIME_MSM_SEC_SEL_CLK_OWNER,
+	PCOM_CLK_REGIME_SEC_DEVMAN_REQUEST_WRP,
+	PCOM_GPIO_CONFIG,
+	PCOM_GPIO_CONFIGURE_GROUP,
+	PCOM_GPIO_TLMM_SET_PORT,
+	PCOM_GPIO_TLMM_CONFIG_EX,
+	PCOM_SET_FTM_BOOT_COUNT,
+	PCOM_RESERVED0,
+	PCOM_RESERVED1,
+	PCOM_CUSTOMER_CMD1,
+	PCOM_CUSTOMER_CMD2,
+	PCOM_CUSTOMER_CMD3,
+	PCOM_CLK_REGIME_ENTER_APPSBL_CHG_MODE,
+	PCOM_CLK_REGIME_EXIT_APPSBL_CHG_MODE,
+	PCOM_CLK_REGIME_SEC_RAIL_DISABLE,
+	PCOM_CLK_REGIME_SEC_RAIL_ENABLE,
+	PCOM_CLK_REGIME_SEC_RAIL_CONTROL,
+	PCOM_SET_SW_WATCHDOG_STATE,
+	PCOM_PM_MPP_CONFIG_DIGITAL_INPUT,
+	PCOM_PM_MPP_CONFIG_I_SINK,
+	PCOM_RESERVED_101,
+	PCOM_MSM_HSUSB_PHY_RESET,
+	PCOM_GET_BATT_MV_LEVEL,
+	PCOM_CHG_USB_IS_PC_CONNECTED,
+	PCOM_CHG_USB_IS_CHARGER_CONNECTED,
+	PCOM_CHG_USB_IS_DISCONNECTED,
+	PCOM_CHG_USB_IS_AVAILABLE,
+	PCOM_CLK_REGIME_SEC_MSM_SEL_FREQ,
+	PCOM_CLK_REGIME_SEC_SET_PCLK_AXI_POLICY,
+	PCOM_CLKCTL_RPC_RESET_ASSERT,
+	PCOM_CLKCTL_RPC_RESET_DEASSERT,
+	PCOM_CLKCTL_RPC_RAIL_ON,
+	PCOM_CLKCTL_RPC_RAIL_OFF,
+	PCOM_CLKCTL_RPC_RAIL_ENABLE,
+	PCOM_CLKCTL_RPC_RAIL_DISABLE,
+	PCOM_CLKCTL_RPC_RAIL_CONTROL,
+	PCOM_CLKCTL_RPC_MIN_MSMC1,
 	PCOM_NUM_CMDS,
 };
 
 enum {
-	 PCOM_INVALID_STATUS = 0x0,
-	 PCOM_READY,
-	 PCOM_CMD_RUNNING,
-	 PCOM_CMD_SUCCESS,
-	 PCOM_CMD_FAIL,
+	PCOM_INVALID_STATUS = 0x0,
+	PCOM_READY,
+	PCOM_CMD_RUNNING,
+	PCOM_CMD_SUCCESS,
+	PCOM_CMD_FAIL,
+	PCOM_CMD_FAIL_FALSE_RETURNED,
+	PCOM_CMD_FAIL_CMD_OUT_OF_BOUNDS_SERVER,
+	PCOM_CMD_FAIL_CMD_OUT_OF_BOUNDS_CLIENT,
+	PCOM_CMD_FAIL_CMD_UNREGISTERED,
+	PCOM_CMD_FAIL_CMD_LOCKED,
+	PCOM_CMD_FAIL_SERVER_NOT_YET_READY,
+	PCOM_CMD_FAIL_BAD_DESTINATION,
+	PCOM_CMD_FAIL_SERVER_RESET,
+	PCOM_CMD_FAIL_SMSM_NOT_INIT,
+	PCOM_CMD_FAIL_PROC_COMM_BUSY,
+	PCOM_CMD_FAIL_PROC_COMM_NOT_INIT,
+
 };
 
 /* List of VREGs that support the Pull Down Resistor setting. */
-enum {
+enum vreg_pdown_id {
 	PM_VREG_PDOWN_MSMA_ID,
 	PM_VREG_PDOWN_MSMP_ID,
 	PM_VREG_PDOWN_MSME1_ID,	/* Not supported in Panoramix */
@@ -131,6 +216,11 @@ enum {
 	PM_VREG_PDOWN_XO_ID = PM_VREG_PDOWN_TCXO_ID
 };
 
+enum {
+        PCOM_CLKRGM_APPS_RESET_USB_PHY  = 34,
+        PCOM_CLKRGM_APPS_RESET_USBH     = 37,
+};
+
 /* gpio info for PCOM_RPC_GPIO_TLMM_CONFIG_EX */
 
 #define GPIO_ENABLE	0