Merge tag 'renesas-sh7372-soc-removal-for-v4.1' of...

Merge tag 'renesas-sh7372-soc-removal-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/multiplatform

Pull "Renesas ARM Based SoC sh7372 SoC Removal Updates for v4.1" from Simon Horman:

* Remove the sh7372 SoC and its mackerel board

* tag 'renesas-sh7372-soc-removal-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  Documentation: Remove ZBOOT MMC/SDHI utility and docs
  ARM: shmobile: sh7372 dtsi: Remove Legacy DTSI file
  ARM: shmobile: sh7372: Remove DT binding documentation
  ARM: shmobile: sh7372: Remove Legacy C SoC code
  ARM: shmobile: sh7372: Remove ZBOOT MMC/SDHI support
  ARM: shmobile: mackerel: Remove from MAINTAINERS
  ARM: shmobile: mackerel: Remove defconfig
  ARM: shmobile: mackerel: Remove mach-type entry
  ARM: shmobile: mackerel: Remove DT binding documentation
  ARM: shmobile: mackerel dts: Remove Legacy DTS file
  ARM: shmobile: mackerel: Remove Legacy C board code
  ARM: shmobile: mackerel: Remove ZBOOT code

[arnd: The sh7372 platform is rather dated and is believed to
 have no active users on modern kernels. It stands in the way
 of converting all of mach-shmobile to be multiplatform capable,
 as adding pinctrl and common-clock support for it would be more
 work than it's  worth. As always, should any legitimate upstream
 users show up in the future, we will revert this removal]

Documentation/Makefile

-subdir-y := accounting arm auxdisplay blackfin connector \
+subdir-y := accounting auxdisplay blackfin connector \
 	filesystems filesystems ia64 laptops mic misc-devices \
 	networking pcmcia prctl ptp spi timers vDSO video4linux \
 	watchdog

Documentation/arm/Makefile

-subdir-y := SH-Mobile

Documentation/arm/SH-Mobile/Makefile

-# List of programs to build
-hostprogs-y := vrl4
-
-# Tell kbuild to always build the programs
-always := $(hostprogs-y)
-
-HOSTCFLAGS_vrl4.o += -I$(objtree)/usr/include -I$(srctree)/tools/include

Documentation/arm/SH-Mobile/vrl4.c

-/*
- * vrl4 format generator
- *
- * Copyright (C) 2010 Simon Horman
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-
-/*
- * usage: vrl4 < zImage > out
- *	  dd if=out of=/dev/sdx bs=512 seek=1 # Write the image to sector 1
- *
- * Reads a zImage from stdin and writes a vrl4 image to stdout.
- * In practice this means writing a padded vrl4 header to stdout followed
- * by the zImage.
- *
- * The padding places the zImage at ALIGN bytes into the output.
- * The vrl4 uses ALIGN + START_BASE as the start_address.
- * This is where the mask ROM will jump to after verifying the header.
- *
- * The header sets copy_size to min(sizeof(zImage), MAX_BOOT_PROG_LEN) + ALIGN.
- * That is, the mask ROM will load the padded header (ALIGN bytes)
- * And then MAX_BOOT_PROG_LEN bytes of the image, or the entire image,
- * whichever is smaller.
- *
- * The zImage is not modified in any way.
- */
-
-#define _BSD_SOURCE
-#include <endian.h>
-#include <unistd.h>
-#include <stdint.h>
-#include <stdio.h>
-#include <errno.h>
-#include <tools/endian.h>
-
-struct hdr {
-	uint32_t magic1;
-	uint32_t reserved1;
-	uint32_t magic2;
-	uint32_t reserved2;
-	uint16_t copy_size;
-	uint16_t boot_options;
-	uint32_t reserved3;
-	uint32_t start_address;
-	uint32_t reserved4;
-	uint32_t reserved5;
-	char     reserved6[308];
-};
-
-#define DECLARE_HDR(h)					\
-	struct hdr (h) = {				\
-		.magic1 =	htole32(0xea000000),	\
-		.reserved1 =	htole32(0x56),		\
-		.magic2 =	htole32(0xe59ff008),	\
-		.reserved3 =	htole16(0x1) }
-
-/* Align to 512 bytes, the MMCIF sector size */
-#define ALIGN_BITS	9
-#define ALIGN		(1 << ALIGN_BITS)
-
-#define START_BASE	0xe55b0000
-
-/*
- * With an alignment of 512 the header uses the first sector.
- * There is a 128 sector (64kbyte) limit on the data loaded by the mask ROM.
- * So there are 127 sectors left for the boot programme. But in practice
- * Only a small portion of a zImage is needed, 16 sectors should be more
- * than enough.
- *
- * Note that this sets how much of the zImage is copied by the mask ROM.
- * The entire zImage is present after the header and is loaded
- * by the code in the boot program (which is the first portion of the zImage).
- */
-#define	MAX_BOOT_PROG_LEN (16 * 512)
-
-#define ROUND_UP(x)	((x + ALIGN - 1) & ~(ALIGN - 1))
-
-static ssize_t do_read(int fd, void *buf, size_t count)
-{
-	size_t offset = 0;
-	ssize_t l;
-
-	while (offset < count) {
-		l = read(fd, buf + offset, count - offset);
-		if (!l)
-			break;
-		if (l < 0) {
-			if (errno == EAGAIN || errno == EWOULDBLOCK)
-				continue;
-			perror("read");
-			return -1;
-		}
-		offset += l;
-	}
-
-	return offset;
-}
-
-static ssize_t do_write(int fd, const void *buf, size_t count)
-{
-	size_t offset = 0;
-	ssize_t l;
-
-	while (offset < count) {
-		l = write(fd, buf + offset, count - offset);
-		if (l < 0) {
-			if (errno == EAGAIN || errno == EWOULDBLOCK)
-				continue;
-			perror("write");
-			return -1;
-		}
-		offset += l;
-	}
-
-	return offset;
-}
-
-static ssize_t write_zero(int fd, size_t len)
-{
-	size_t i = len;
-
-	while (i--) {
-		const char x = 0;
-		if (do_write(fd, &x, 1) < 0)
-			return -1;
-	}
-
-	return len;
-}
-
-int main(void)
-{
-	DECLARE_HDR(hdr);
-	char boot_program[MAX_BOOT_PROG_LEN];
-	size_t aligned_hdr_len, alligned_prog_len;
-	ssize_t prog_len;
-
-	prog_len = do_read(0, boot_program, sizeof(boot_program));
-	if (prog_len <= 0)
-		return -1;
-
-	aligned_hdr_len = ROUND_UP(sizeof(hdr));
-	hdr.start_address = htole32(START_BASE + aligned_hdr_len);
-	alligned_prog_len = ROUND_UP(prog_len);
-	hdr.copy_size = htole16(aligned_hdr_len + alligned_prog_len);
-
-	if (do_write(1, &hdr, sizeof(hdr)) < 0)
-		return -1;
-	if (write_zero(1, aligned_hdr_len - sizeof(hdr)) < 0)
-		return -1;
-
-	if (do_write(1, boot_program, prog_len) < 0)
-		return 1;
-
-	/* Write out the rest of the kernel */
-	while (1) {
-		prog_len = do_read(0, boot_program, sizeof(boot_program));
-		if (prog_len < 0)
-			return 1;
-		if (prog_len == 0)
-			break;
-		if (do_write(1, boot_program, prog_len) < 0)
-			return 1;
-	}
-
-	return 0;
-}

Documentation/arm/SH-Mobile/zboot-rom-mmcif.txt

-ROM-able zImage boot from MMC
------------------------------
-
-An ROM-able zImage compiled with ZBOOT_ROM_MMCIF may be written to MMC and
-SuperH Mobile ARM will to boot directly from the MMCIF hardware block.
-
-This is achieved by the mask ROM loading the first portion of the image into
-MERAM and then jumping to it. This portion contains loader code which
-copies the entire image to SDRAM and jumps to it. From there the zImage
-boot code proceeds as normal, uncompressing the image into its final
-location and then jumping to it.
-
-This code has been tested on an AP4EB board using the developer 1A eMMC
-boot mode which is configured using the following jumper settings.
-The board used for testing required a patched mask ROM in order for
-this mode to function.
-
-   8 7 6 5 4 3 2 1
-   x|x|x|x|x| |x|
-S4 -+-+-+-+-+-+-+-
-    | | | | |x| |x on
-
-The zImage must be written to the MMC card at sector 1 (512 bytes) in
-vrl4 format. A utility vrl4 is supplied to accomplish this.
-
-e.g.
-	vrl4 < zImage | dd of=/dev/sdX bs=512 seek=1
-
-A dual-voltage MMC 4.0 card was used for testing.

Documentation/arm/SH-Mobile/zboot-rom-sdhi.txt

-ROM-able zImage boot from eSD
------------------------------
-
-An ROM-able zImage compiled with ZBOOT_ROM_SDHI may be written to eSD and
-SuperH Mobile ARM will to boot directly from the SDHI hardware block.
-
-This is achieved by the mask ROM loading the first portion of the image into
-MERAM and then jumping to it. This portion contains loader code which
-copies the entire image to SDRAM and jumps to it. From there the zImage
-boot code proceeds as normal, uncompressing the image into its final
-location and then jumping to it.
-
-This code has been tested on an mackerel board using the developer 1A eSD
-boot mode which is configured using the following jumper settings.
-
-   8 7 6 5 4 3 2 1
-   x|x|x|x| |x|x|
-S4 -+-+-+-+-+-+-+-
-    | | | |x| | |x on
-
-The eSD card needs to be present in SDHI slot 1 (CN7).
-As such S1 and S33 also need to be configured as per
-the notes in arch/arm/mach-shmobile/board-mackerel.c.
-
-A partial zImage must be written to physical partition #1 (boot)
-of the eSD at sector 0 in vrl4 format. A utility vrl4 is supplied to
-accomplish this.
-
-e.g.
-	vrl4 < zImage | dd of=/dev/sdX bs=512 count=17
-
-A full copy of _the same_ zImage should be written to physical partition #1
-(boot) of the eSD at sector 0. This should _not_ be in vrl4 format.
-
-	vrl4 < zImage | dd of=/dev/sdX bs=512
-
-Note: The commands above assume that the physical partition has been
-switched. No such facility currently exists in the Linux Kernel.
-
-Physical partitions are described in the eSD specification.  At the time of
-writing they are not the same as partitions that are typically configured
-using fdisk and visible through /proc/partitions

Documentation/devicetree/bindings/arm/shmobile.txt

@@ -7,8 +7,6 @@ SoCs:
     compatible = "renesas,emev2"
   - RZ/A1H (R7S72100)
     compatible = "renesas,r7s72100"
-  - SH-Mobile AP4 (R8A73720/SH7372)
-    compatible = "renesas,sh7372"
   - SH-Mobile AG5 (R8A73A00/SH73A0)
     compatible = "renesas,sh73a0"
   - R-Mobile APE6 (R8A73A40)
@@ -61,8 +59,6 @@ Boards:
     compatible = "renesas,kzm9g-reference", "renesas,sh73a0"
   - Lager (RTP0RC7790SEB00010S)
     compatible = "renesas,lager", "renesas,r8a7790"
-  - Mackerel (R0P7372LC0016RL, AP4 EVM 2nd)
-    compatible = "renesas,mackerel"
   - Marzen
     compatible = "renesas,marzen", "renesas,r8a7779"
 

MAINTAINERS

@@ -1418,7 +1418,6 @@ F:	arch/arm/configs/ape6evm_defconfig
 F:	arch/arm/configs/armadillo800eva_defconfig
 F:	arch/arm/configs/bockw_defconfig
 F:	arch/arm/configs/kzm9g_defconfig
-F:	arch/arm/configs/mackerel_defconfig
 F:	arch/arm/configs/marzen_defconfig
 F:	arch/arm/configs/shmobile_defconfig
 F:	arch/arm/include/debug/renesas-scif.S

arch/arm/Kconfig

@@ -1847,35 +1847,6 @@ config ZBOOT_ROM
 	  Say Y here if you intend to execute your compressed kernel image
 	  (zImage) directly from ROM or flash.  If unsure, say N.
 
-choice
-	prompt "Include SD/MMC loader in zImage (EXPERIMENTAL)"
-	depends on ZBOOT_ROM && ARCH_SH7372
-	default ZBOOT_ROM_NONE
-	help
-	  Include experimental SD/MMC loading code in the ROM-able zImage.
-	  With this enabled it is possible to write the ROM-able zImage
-	  kernel image to an MMC or SD card and boot the kernel straight
-	  from the reset vector. At reset the processor Mask ROM will load
-	  the first part of the ROM-able zImage which in turn loads the
-	  rest the kernel image to RAM.
-
-config ZBOOT_ROM_NONE
-	bool "No SD/MMC loader in zImage (EXPERIMENTAL)"
-	help
-	  Do not load image from SD or MMC
-
-config ZBOOT_ROM_MMCIF
-	bool "Include MMCIF loader in zImage (EXPERIMENTAL)"
-	help
-	  Load image from MMCIF hardware block.
-
-config ZBOOT_ROM_SH_MOBILE_SDHI
-	bool "Include SuperH Mobile SDHI loader in zImage (EXPERIMENTAL)"
-	help
-	  Load image from SDHI hardware block
-
-endchoice
-
 config ARM_APPENDED_DTB
 	bool "Use appended device tree blob to zImage (EXPERIMENTAL)"
 	depends on OF

arch/arm/Kconfig.debug

@@ -821,12 +821,11 @@ choice
 		  via SCIF2 on Renesas R-Car E2 (R8A7794).
 
 	config DEBUG_RMOBILE_SCIFA0
-		bool "Kernel low-level debugging messages via SCIFA0 on R8A73A4/SH7372"
-		depends on ARCH_R8A73A4 || ARCH_SH7372
+		bool "Kernel low-level debugging messages via SCIFA0 on R8A73A4"
+		depends on ARCH_R8A73A4
 		help
 		  Say Y here if you want kernel low-level debugging support
-		  via SCIFA0 on Renesas R-Mobile APE6 (R8A73A4) or SH-Mobile
-		  AP4 (SH7372).
+		  via SCIFA0 on Renesas R-Mobile APE6 (R8A73A4).
 
 	config DEBUG_RMOBILE_SCIFA1
 		bool "Kernel low-level debugging messages via SCIFA1 on R8A7740"

arch/arm/boot/compressed/Makefile

@@ -6,21 +6,6 @@
 
 OBJS		=
 
-# Ensure that MMCIF loader code appears early in the image
-# to minimise that number of bocks that have to be read in
-# order to load it.
-ifeq ($(CONFIG_ZBOOT_ROM_MMCIF),y)
-OBJS		+= mmcif-sh7372.o
-endif
-
-# Ensure that SDHI loader code appears early in the image
-# to minimise that number of bocks that have to be read in
-# order to load it.
-ifeq ($(CONFIG_ZBOOT_ROM_SH_MOBILE_SDHI),y)
-OBJS		+= sdhi-shmobile.o
-OBJS		+= sdhi-sh7372.o
-endif
-
 AFLAGS_head.o += -DTEXT_OFFSET=$(TEXT_OFFSET)
 HEAD	= head.o
 OBJS	+= misc.o decompress.o

arch/arm/boot/compressed/head-shmobile.S

@@ -25,36 +25,6 @@
 	/* load board-specific initialization code */
 #include <mach/zboot.h>
 
-#if defined(CONFIG_ZBOOT_ROM_MMCIF) || defined(CONFIG_ZBOOT_ROM_SH_MOBILE_SDHI)
-	/* Load image from MMC/SD */
-	adr	sp, __tmp_stack + 256
-	ldr	r0, __image_start
-	ldr	r1, __image_end
-	subs	r1, r1, r0
-	ldr	r0, __load_base
-	bl	mmc_loader
-
-	/* Jump to loaded code */
-	ldr	r0, __loaded
-	ldr	r1, __image_start
-	sub	r0, r0, r1
-	ldr	r1, __load_base
-	add	pc, r0, r1
-
-__image_start:
-	.long	_start
-__image_end:
-	.long	_got_end
-__load_base:
-	.long	MEMORY_START + 0x02000000 @ Load at 32Mb into SDRAM
-__loaded:
-	.long	__continue
-	.align
-__tmp_stack:
-	.space	256
-__continue:
-#endif /* CONFIG_ZBOOT_ROM_MMC || CONFIG_ZBOOT_ROM_SH_MOBILE_SDHI */
-
 	adr	r0, dtb_info
 	ldmia	r0, {r1, r3, r4, r5, r7}
 

arch/arm/boot/compressed/mmcif-sh7372.c

-/*
- * sh7372 MMCIF loader
- *
- * Copyright (C) 2010 Magnus Damm
- * Copyright (C) 2010 Simon Horman
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-
-#include <linux/mmc/sh_mmcif.h>
-#include <linux/mmc/boot.h>
-#include <mach/mmc.h>
-
-#define MMCIF_BASE      (void __iomem *)0xe6bd0000
-
-#define PORT84CR	(void __iomem *)0xe6050054
-#define PORT85CR	(void __iomem *)0xe6050055
-#define PORT86CR	(void __iomem *)0xe6050056
-#define PORT87CR	(void __iomem *)0xe6050057
-#define PORT88CR	(void __iomem *)0xe6050058
-#define PORT89CR	(void __iomem *)0xe6050059
-#define PORT90CR	(void __iomem *)0xe605005a
-#define PORT91CR	(void __iomem *)0xe605005b
-#define PORT92CR	(void __iomem *)0xe605005c
-#define PORT99CR	(void __iomem *)0xe6050063
-
-#define SMSTPCR3	(void __iomem *)0xe615013c
-
-/* SH7372 specific MMCIF loader
- *
- * loads the zImage from an MMC card starting from block 1.
- *
- * The image must be start with a vrl4 header and
- * the zImage must start at offset 512 of the image. That is,
- * at block 2 (=byte 1024) on the media
- *
- * Use the following line to write the vrl4 formated zImage
- * to an MMC card
- * # dd if=vrl4.out of=/dev/sdx bs=512 seek=1
- */
-asmlinkage void mmc_loader(unsigned char *buf, unsigned long len)
-{
-	mmc_init_progress();
-	mmc_update_progress(MMC_PROGRESS_ENTER);
-
-	/* Initialise MMC
-	 * registers: PORT84CR-PORT92CR
-	 *            (MMCD0_0-MMCD0_7,MMCCMD0 Control)
-	 * value: 0x04 - select function 4
-	 */
-	 __raw_writeb(0x04, PORT84CR);
-	 __raw_writeb(0x04, PORT85CR);
-	 __raw_writeb(0x04, PORT86CR);
-	 __raw_writeb(0x04, PORT87CR);
-	 __raw_writeb(0x04, PORT88CR);
-	 __raw_writeb(0x04, PORT89CR);
-	 __raw_writeb(0x04, PORT90CR);
-	 __raw_writeb(0x04, PORT91CR);
-	 __raw_writeb(0x04, PORT92CR);
-
-	/* Initialise MMC
-	 * registers: PORT99CR (MMCCLK0 Control)
-	 * value: 0x10 | 0x04 - enable output | select function 4
-	 */
-	__raw_writeb(0x14, PORT99CR);
-
-	/* Enable clock to MMC hardware block */
-	__raw_writel(__raw_readl(SMSTPCR3) & ~(1 << 12), SMSTPCR3);
-
-	mmc_update_progress(MMC_PROGRESS_INIT);
-
-	/* setup MMCIF hardware */
-	sh_mmcif_boot_init(MMCIF_BASE);
-
-	mmc_update_progress(MMC_PROGRESS_LOAD);
-
-	/* load kernel via MMCIF interface */
-	sh_mmcif_boot_do_read(MMCIF_BASE, 2, /* Kernel is at block 2 */
-			      (len + SH_MMCIF_BBS - 1) / SH_MMCIF_BBS, buf);
-
-
-	/* Disable clock to MMC hardware block */
-	__raw_writel(__raw_readl(SMSTPCR3) | (1 << 12), SMSTPCR3);
-
-	mmc_update_progress(MMC_PROGRESS_DONE);
-}

arch/arm/boot/compressed/sdhi-sh7372.c

-/*
- * SuperH Mobile SDHI
- *
- * Copyright (C) 2010 Magnus Damm
- * Copyright (C) 2010 Kuninori Morimoto
- * Copyright (C) 2010 Simon Horman
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Parts inspired by u-boot
- */
-
-#include <linux/io.h>
-#include <mach/mmc.h>
-#include <linux/mmc/boot.h>
-#include <linux/mmc/tmio.h>
-
-#include "sdhi-shmobile.h"
-
-#define PORT179CR       0xe60520b3
-#define PORT180CR       0xe60520b4
-#define PORT181CR       0xe60520b5
-#define PORT182CR       0xe60520b6
-#define PORT183CR       0xe60520b7
-#define PORT184CR       0xe60520b8
-
-#define SMSTPCR3        0xe615013c
-
-#define CR_INPUT_ENABLE 0x10
-#define CR_FUNCTION1    0x01
-
-#define SDHI1_BASE	(void __iomem *)0xe6860000
-#define SDHI_BASE	SDHI1_BASE
-
-/*  SuperH Mobile SDHI loader
- *
- * loads the zImage from an SD card starting from block 0
- * on physical partition 1
- *
- * The image must be start with a vrl4 header and
- * the zImage must start at offset 512 of the image. That is,
- * at block 1 (=byte 512) of physical partition 1
- *
- * Use the following line to write the vrl4 formated zImage
- * to an SD card
- * # dd if=vrl4.out of=/dev/sdx bs=512
- */
-asmlinkage void mmc_loader(unsigned short *buf, unsigned long len)
-{
-	int high_capacity;
-
-	mmc_init_progress();
-
-	mmc_update_progress(MMC_PROGRESS_ENTER);
-        /* Initialise SDHI1 */
-        /* PORT184CR: GPIO_FN_SDHICMD1 Control */
-        __raw_writeb(CR_FUNCTION1, PORT184CR);
-        /* PORT179CR: GPIO_FN_SDHICLK1 Control */
-        __raw_writeb(CR_INPUT_ENABLE|CR_FUNCTION1, PORT179CR);
-        /* PORT181CR: GPIO_FN_SDHID1_3 Control */
-        __raw_writeb(CR_FUNCTION1, PORT183CR);
-        /* PORT182CR: GPIO_FN_SDHID1_2 Control */
-        __raw_writeb(CR_FUNCTION1, PORT182CR);
-        /* PORT183CR: GPIO_FN_SDHID1_1 Control */
-        __raw_writeb(CR_FUNCTION1, PORT181CR);
-        /* PORT180CR: GPIO_FN_SDHID1_0 Control */
-        __raw_writeb(CR_FUNCTION1, PORT180CR);
-
-        /* Enable clock to SDHI1 hardware block */
-        __raw_writel(__raw_readl(SMSTPCR3) & ~(1 << 13), SMSTPCR3);
-
-	/* setup SDHI hardware */
-	mmc_update_progress(MMC_PROGRESS_INIT);
-	high_capacity = sdhi_boot_init(SDHI_BASE);
-	if (high_capacity < 0)
-		goto err;
-
-	mmc_update_progress(MMC_PROGRESS_LOAD);
-	/* load kernel */
-	if (sdhi_boot_do_read(SDHI_BASE, high_capacity,
-			      0, /* Kernel is at block 1 */
-			      (len + TMIO_BBS - 1) / TMIO_BBS, buf))
-		goto err;
-
-        /* Disable clock to SDHI1 hardware block */
-        __raw_writel(__raw_readl(SMSTPCR3) | (1 << 13), SMSTPCR3);
-
-	mmc_update_progress(MMC_PROGRESS_DONE);
-
-	return;
-err:
-	for(;;);
-}

arch/arm/boot/compressed/sdhi-shmobile.h

-#ifndef SDHI_MOBILE_H
-#define SDHI_MOBILE_H
-
-#include <linux/compiler.h>
-
-int sdhi_boot_do_read(void __iomem *base, int high_capacity,
-		      unsigned long offset, unsigned short count,
-		      unsigned short *buf);
-int sdhi_boot_init(void __iomem *base);
-
-#endif

arch/arm/boot/dts/Makefile

@@ -470,7 +470,6 @@ dtb-$(CONFIG_ARCH_SHMOBILE_LEGACY) += \
 	r8a7778-bockw.dtb \
 	r8a7778-bockw-reference.dtb \
 	r8a7779-marzen.dtb \
-	sh7372-mackerel.dtb \
 	sh73a0-kzm9g.dtb \
 	sh73a0-kzm9g-reference.dtb
 dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \

arch/arm/boot/dts/sh7372-mackerel.dts

-/*
- * Device Tree Source for the mackerel board
- *
- * Copyright (C) 2012 Renesas Solutions Corp.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-/dts-v1/;
-#include "sh7372.dtsi"
-
-/ {
-	model = "Mackerel (AP4 EVM 2nd)";
-	compatible = "renesas,mackerel";
-
-	chosen {
-		bootargs = "console=tty0, console=ttySC0,115200 earlyprintk=sh-sci.0,115200 root=/dev/nfs nfsroot=,tcp,v3 ip=dhcp mem=240m rw";
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x40000000 0x10000000>;
-	};
-};

arch/arm/boot/dts/sh7372.dtsi

-/*
- * Device Tree Source for the sh7372 SoC
- *
- * Copyright (C) 2012 Renesas Solutions Corp.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-/include/ "skeleton.dtsi"
-
-/ {
-	compatible = "renesas,sh7372";
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu@0 {
-			compatible = "arm,cortex-a8";
-			device_type = "cpu";
-			reg = <0x0>;
-			clock-frequency = <800000000>;
-		};
-	};
-
-	pfc: pfc@e6050000 {
-		compatible = "renesas,pfc-sh7372";
-		reg = <0xe6050000 0x8000>,
-		      <0xe605801c 0x1c>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-};

arch/arm/configs/mackerel_defconfig

-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=16
-# CONFIG_UTS_NS is not set
-# CONFIG_IPC_NS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_PID_NS is not set
-# CONFIG_NET_NS is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_SHMOBILE_LEGACY=y
-CONFIG_ARCH_SH7372=y
-CONFIG_MACH_MACKEREL=y
-CONFIG_MEMORY_SIZE=0x10000000
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-CONFIG_FORCE_MAX_ZONEORDER=15
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_KEXEC=y
-CONFIG_VFP=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-CONFIG_PM=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_IPV6 is not set
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-# CONFIG_FIRMWARE_IN_KERNEL is not set
-CONFIG_MTD=y
-CONFIG_MTD_CONCAT=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_ARM_INTEGRATOR=y
-CONFIG_MTD_BLOCK2MTD=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-# CONFIG_SCSI_LOWLEVEL is not set
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_SMSC911X=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_SERIAL_SH_SCI=y
-CONFIG_SERIAL_SH_SCI_NR_UARTS=8
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-CONFIG_I2C_SH_MOBILE=y
-# CONFIG_HWMON is not set
-# CONFIG_MFD_SUPPORT is not set
-CONFIG_REGULATOR=y
-CONFIG_FB=y
-CONFIG_FB_MODE_HELPERS=y
-CONFIG_FB_SH_MOBILE_LCDC=y
-CONFIG_FB_SH_MOBILE_HDMI=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_LOGO=y
-# CONFIG_LOGO_LINUX_MONO is not set
-# CONFIG_LOGO_LINUX_CLUT224 is not set
-# CONFIG_SND_SUPPORT_OLD_API is not set
-# CONFIG_SND_VERBOSE_PROCFS is not set
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_ARM is not set
-CONFIG_SND_SOC_SH4_FSI=y
-CONFIG_USB=y
-CONFIG_USB_RENESAS_USBHS_HCD=y
-CONFIG_USB_RENESAS_USBHS=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_RENESAS_USBHS_UDC=y
-CONFIG_MMC=y
-CONFIG_MMC_SDHI=y
-CONFIG_MMC_SH_MMCIF=y
-CONFIG_DMADEVICES=y
-CONFIG_SH_DMAE=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT2_FS_XATTR=y
-CONFIG_EXT2_FS_POSIX_ACL=y
-CONFIG_EXT2_FS_SECURITY=y
-CONFIG_EXT2_FS_XIP=y
-CONFIG_EXT3_FS=y
-# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
-CONFIG_EXT3_FS_POSIX_ACL=y
-CONFIG_EXT3_FS_SECURITY=y
-# CONFIG_DNOTIFY is not set
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-# CONFIG_MISC_FILESYSTEMS is not set
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_V4_1=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_737=y
-CONFIG_NLS_CODEPAGE_775=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_CODEPAGE_852=y
-CONFIG_NLS_CODEPAGE_855=y
-CONFIG_NLS_CODEPAGE_857=y
-CONFIG_NLS_CODEPAGE_860=y
-CONFIG_NLS_CODEPAGE_861=y
-CONFIG_NLS_CODEPAGE_862=y
-CONFIG_NLS_CODEPAGE_863=y
-CONFIG_NLS_CODEPAGE_864=y
-CONFIG_NLS_CODEPAGE_865=y
-CONFIG_NLS_CODEPAGE_866=y
-CONFIG_NLS_CODEPAGE_869=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_ISO8859_2=y
-CONFIG_NLS_ISO8859_3=y
-CONFIG_NLS_ISO8859_4=y
-CONFIG_NLS_ISO8859_5=y
-CONFIG_NLS_ISO8859_6=y
-CONFIG_NLS_ISO8859_7=y
-CONFIG_NLS_ISO8859_9=y
-CONFIG_NLS_ISO8859_13=y
-CONFIG_NLS_ISO8859_14=y
-CONFIG_NLS_ISO8859_15=y
-CONFIG_NLS_KOI8_R=y
-CONFIG_NLS_KOI8_U=y
-CONFIG_NLS_UTF8=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_ENABLE_MUST_CHECK is not set
-# CONFIG_ARM_UNWIND is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ANSI_CPRNG=y

arch/arm/mach-shmobile/Kconfig

@@ -92,13 +92,6 @@ if ARCH_SHMOBILE_LEGACY
 
 comment "Renesas ARM SoCs System Type"
 
-config ARCH_SH7372
-	bool "SH-Mobile AP4 (SH7372)"
-	select ARCH_RMOBILE
-	select ARCH_WANT_OPTIONAL_GPIOLIB
-	select ARM_CPU_SUSPEND if PM || CPU_IDLE
-	select SH_INTC
-
 config ARCH_SH73A0
 	bool "SH-Mobile AG5 (R8A73A00)"
 	select ARCH_RMOBILE
@@ -154,15 +147,6 @@ config MACH_APE6EVM_REFERENCE
 
 	   This is intended to aid developers
 
-config MACH_MACKEREL
-	bool "mackerel board"
-	depends on ARCH_SH7372
-	select ARCH_REQUIRE_GPIOLIB
-	select REGULATOR_FIXED_VOLTAGE if REGULATOR
-	select SMSC_PHY if SMSC911X
-	select SND_SOC_AK4642 if SND_SIMPLE_CARD
-	select USE_OF
-
 config MACH_ARMADILLO800EVA
 	bool "Armadillo-800 EVA board"
 	depends on ARCH_R8A7740

arch/arm/mach-shmobile/Makefile

@@ -6,7 +6,6 @@
 obj-y				:= timer.o console.o
 
 # CPU objects
-obj-$(CONFIG_ARCH_SH7372)	+= setup-sh7372.o intc-sh7372.o pm-sh7372.o
 obj-$(CONFIG_ARCH_SH73A0)	+= setup-sh73a0.o intc-sh73a0.o pm-sh73a0.o
 obj-$(CONFIG_ARCH_R8A73A4)	+= setup-r8a73a4.o
 obj-$(CONFIG_ARCH_R8A7740)	+= setup-r8a7740.o pm-r8a7740.o
@@ -21,7 +20,6 @@ obj-$(CONFIG_ARCH_R7S72100)	+= setup-r7s72100.o
 # Clock objects
 ifndef CONFIG_COMMON_CLK
 obj-y				+= clock.o
-obj-$(CONFIG_ARCH_SH7372)	+= clock-sh7372.o
 obj-$(CONFIG_ARCH_SH73A0)	+= clock-sh73a0.o
 obj-$(CONFIG_ARCH_R8A73A4)	+= clock-r8a73a4.o
 obj-$(CONFIG_ARCH_R8A7740)	+= clock-r8a7740.o
@@ -51,16 +49,12 @@ obj-$(CONFIG_CPU_FREQ)		+= cpufreq.o
 obj-$(CONFIG_PM_RCAR)		+= pm-rcar.o
 obj-$(CONFIG_PM_RMOBILE)	+= pm-rmobile.o
 
-# special sh7372 handling for IRQ objects and low level sleep code
-obj-$(CONFIG_ARCH_SH7372)	+= entry-intc.o sleep-sh7372.o
-
 # Board objects
 ifdef CONFIG_ARCH_SHMOBILE_MULTI
 obj-$(CONFIG_MACH_MARZEN)	+= board-marzen-reference.o
 else
 obj-$(CONFIG_MACH_APE6EVM)	+= board-ape6evm.o
 obj-$(CONFIG_MACH_APE6EVM_REFERENCE)	+= board-ape6evm-reference.o
-obj-$(CONFIG_MACH_MACKEREL)	+= board-mackerel.o
 obj-$(CONFIG_MACH_BOCKW)	+= board-bockw.o
 obj-$(CONFIG_MACH_BOCKW_REFERENCE)	+= board-bockw-reference.o
 obj-$(CONFIG_MACH_MARZEN)	+= board-marzen.o

arch/arm/mach-shmobile/Makefile.boot

@@ -7,7 +7,6 @@ loadaddr-$(CONFIG_MACH_BOCKW) += 0x60008000
 loadaddr-$(CONFIG_MACH_BOCKW_REFERENCE) += 0x60008000
 loadaddr-$(CONFIG_MACH_KZM9G) += 0x41008000
 loadaddr-$(CONFIG_MACH_KZM9G_REFERENCE) += 0x41008000
-loadaddr-$(CONFIG_MACH_MACKEREL) += 0x40008000
 loadaddr-$(CONFIG_MACH_MARZEN) += 0x60008000
 
 __ZRELADDR	:= $(sort $(loadaddr-y))

arch/arm/mach-shmobile/common.h

@@ -21,7 +21,6 @@ extern void shmobile_smp_scu_cpu_die(unsigned int cpu);
 extern int shmobile_smp_scu_cpu_kill(unsigned int cpu);
 struct clk;
 extern int shmobile_clk_init(void);
-extern void shmobile_handle_irq_intc(struct pt_regs *);
 extern struct platform_suspend_ops shmobile_suspend_ops;
 struct cpuidle_driver;
 extern void shmobile_cpuidle_set_driver(struct cpuidle_driver *drv);

arch/arm/mach-shmobile/entry-intc.S

-/*
- * ARM Interrupt demux handler using INTC
- *
- * Copyright (C) 2010 Magnus Damm
- * Copyright (C) 2008 Renesas Solutions Corp.
- *
- * This file is licensed under  the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <asm/entry-macro-multi.S>
-
-#define INTCA_BASE	0xe6980000
-#define INTFLGA_OFFS	0x00000018 /* accept pending interrupt */
-#define INTEVTA_OFFS	0x00000020 /* vector number of accepted interrupt */
-#define INTLVLA_OFFS	0x00000030 /* priority level of accepted interrupt */
-#define INTLVLB_OFFS	0x00000034 /* previous priority level */
-
-	.macro  get_irqnr_preamble, base, tmp
-	ldr     \base, =INTCA_BASE
-	.endm
-
-	.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-	/* The single INTFLGA read access below results in the following:
-	 *
-	 * 1. INTLVLB is updated with old priority value from INTLVLA
-	 * 2. Highest priority interrupt is accepted
-	 * 3. INTLVLA is updated to contain priority of accepted interrupt
-	 * 4. Accepted interrupt vector is stored in INTFLGA and INTEVTA
-	 */
-	ldr     \irqnr, [\base, #INTFLGA_OFFS]
-
-	/* Restore INTLVLA with the value saved in INTLVLB.
-	 * This is required to support interrupt priorities properly.
-	 */
-	ldrb	\tmp, [\base, #INTLVLB_OFFS]
-	strb    \tmp, [\base, #INTLVLA_OFFS]
-
-	/* Handle invalid vector number case */
-	cmp	\irqnr, #0
-	beq	1000f
-
-	/* Convert vector to irq number, same as the evt2irq() macro */
-	lsr	\irqnr, \irqnr, #0x5
-	subs	\irqnr, \irqnr, #16
-
-1000:
-	.endm
-
-	.macro  test_for_ipi, irqnr, irqstat, base, tmp
-	.endm
-
-	arch_irq_handler shmobile_handle_irq_intc

arch/arm/mach-shmobile/include/mach/head-mackerel.txt

-LIST "partner-jet-setup.txt"
-LIST "(C) Copyright 2010 Renesas Solutions Corp"
-LIST "Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>"
-
-LIST "RWT Setting"
-EW 0xE6020004, 0xA500
-EW 0xE6030004, 0xA500
-
-LIST "GPIO Setting"
-EB 0xE6051013, 0xA2
-
-LIST "CPG"
-ED 0xE61500C0, 0x00000002
-
-WAIT 1, 0xFE40009C
-
-LIST "FRQCR"
-ED 0xE6150000, 0x2D1305C3
-ED 0xE61500E0, 0x9E40358E
-ED 0xE6150004, 0x80331050
-
-WAIT 1, 0xFE40009C
-
-ED 0xE61500E4, 0x00002000
-
-WAIT 1, 0xFE40009C
-
-LIST "PLL"
-ED 0xE6150028, 0x00004000
-
-WAIT 1, 0xFE40009C
-
-ED 0xE615002C, 0x93000040
-
-WAIT 1, 0xFE40009C
-
-LIST "SUB/USBClk"
-ED 0xE6150080, 0x00000180
-
-LIST "BSC"
-ED 0xFEC10000, 0x00E0001B
-
-LIST "SBSC1"
-ED 0xFE400354, 0x01AD8000
-ED 0xFE400354, 0x01AD8001
-
-WAIT 5, 0xFE40009C
-
-ED 0xFE400008, 0xBCC90151
-ED 0xFE400040, 0x41774113
-ED 0xFE400044, 0x2712E229
-ED 0xFE400048, 0x20C18505
-ED 0xFE40004C, 0x00110209
-ED 0xFE400010, 0x00000087
-
-WAIT 30, 0xFE40009C
-
-ED 0xFE400084, 0x0000003F
-EB 0xFE500000, 0x00
-
-WAIT 5, 0xFE40009C
-
-ED 0xFE400084, 0x0000FF0A
-EB 0xFE500000, 0x00
-
-WAIT 1, 0xFE40009C
-
-ED 0xFE400084, 0x00002201
-EB 0xFE500000, 0x00
-ED 0xFE400084, 0x00000302
-EB 0xFE500000, 0x00
-EB 0xFE5C0000, 0x00
-ED 0xFE400008, 0xBCC90159
-ED 0xFE40008C, 0x88800004
-ED 0xFE400094, 0x00000004
-ED 0xFE400028, 0xA55A0032
-ED 0xFE40002C, 0xA55A000C
-ED 0xFE400020, 0xA55A2048
-ED 0xFE400008, 0xBCC90959
-
-LIST "Change CPGA setting"
-ED 0xE61500E0, 0x9E40352E
-ED 0xE6150004, 0x80331050
-
-WAIT 1, 0xFE40009C
-
-ED 0xFE400354, 0x01AD8002
-
-LIST "SCIF0 - Serial port for earlyprintk"
-EB 0xE6053098, 0xe1
-EW 0xE6C40000, 0x0000
-EB 0xE6C40004, 0x19
-EW 0xE6C40008, 0x0030

arch/arm/mach-shmobile/include/mach/mmc-mackerel.h

-#ifndef MMC_MACKEREL_H
-#define MMC_MACKEREL_H
-
-#define PORT0CR      (void __iomem *)0xe6051000
-#define PORT1CR      (void __iomem *)0xe6051001
-#define PORT2CR      (void __iomem *)0xe6051002
-#define PORT159CR    (void __iomem *)0xe605009f
-
-#define PORTR031_000DR (void __iomem *)0xe6055000
-#define PORTL159_128DR (void __iomem *)0xe6054010
-
-static inline void mmc_init_progress(void)
-{
-       /* Initialise LEDS0-3
-        * registers: PORT0CR-PORT2CR,PORT159CR (LED0-LED3 Control)
-        * value:     0x10 - enable output
-        */
-       __raw_writeb(0x10, PORT0CR);
-       __raw_writeb(0x10, PORT1CR);
-       __raw_writeb(0x10, PORT2CR);
-       __raw_writeb(0x10, PORT159CR);
-}
-
-static inline void mmc_update_progress(int n)
-{
-	unsigned a = 0, b = 0;
-
-	if (n < 3)
-		a = 1 << n;
-	else
-		b = 1 << 31;
-
-	__raw_writel((__raw_readl(PORTR031_000DR) & ~0x7) | a,
-		     PORTR031_000DR);
-	__raw_writel((__raw_readl(PORTL159_128DR) & ~(1 << 31)) | b,
-		     PORTL159_128DR);
-}
-#endif /* MMC_MACKEREL_H */

arch/arm/mach-shmobile/include/mach/mmc.h

-#ifndef MMC_H
-#define MMC_H
-
-/**************************************************
- *
- *		board specific settings
- *
- **************************************************/
-
-#ifdef CONFIG_MACH_MACKEREL
-#include "mach/mmc-mackerel.h"
-#else
-#error "unsupported board."
-#endif
-
-#endif /* MMC_H */

arch/arm/mach-shmobile/include/mach/sdhi-sh7372.h

-#ifndef SDHI_SH7372_H
-#define SDHI_SH7372_H
-
-#define SDGENCNTA       0xfe40009c
-
-/* The countdown of SDGENCNTA is controlled by
- * ZB3D2CLK which runs at 149.5MHz.
- * That is 149.5ticks/us. Approximate this as 150ticks/us.
- */
-static void udelay(int us)
-{
-	__raw_writel(us * 150, SDGENCNTA);
-	while(__raw_readl(SDGENCNTA)) ;
-}
-
-static void msleep(int ms)
-{
-	udelay(ms * 1000);
-}
-
-#endif

arch/arm/mach-shmobile/include/mach/sdhi.h

-#ifndef SDHI_H
-#define SDHI_H
-
-/**************************************************
- *
- *		CPU specific settings
- *
- **************************************************/
-
-#ifdef CONFIG_ARCH_SH7372
-#include "mach/sdhi-sh7372.h"
-#else
-#error "unsupported CPU."
-#endif
-
-#endif /* SDHI_H */

arch/arm/mach-shmobile/include/mach/zboot.h

@@ -9,10 +9,7 @@
  *
  **************************************************/
 
-#ifdef CONFIG_MACH_MACKEREL
-#define MEMORY_START	0x40000000
-#include "mach/head-mackerel.txt"
-#elif defined(CONFIG_MACH_KZM9G) || defined(CONFIG_MACH_KZM9G_REFERENCE)
+#if defined(CONFIG_MACH_KZM9G) || defined(CONFIG_MACH_KZM9G_REFERENCE)
 #define MEMORY_START	0x43000000
 #include "mach/head-kzm9g.txt"
 #else

arch/arm/tools/mach-types

@@ -526,7 +526,6 @@ ag5evm			MACH_AG5EVM		AG5EVM			3189
 ics_if_voip		MACH_ICS_IF_VOIP	ICS_IF_VOIP		3206
 wlf_cragg_6410		MACH_WLF_CRAGG_6410	WLF_CRAGG_6410		3207
 trimslice		MACH_TRIMSLICE		TRIMSLICE		3209
-mackerel		MACH_MACKEREL		MACKEREL		3211
 kaen			MACH_KAEN		KAEN			3217
 nokia_rm680		MACH_NOKIA_RM680	NOKIA_RM680		3220
 msm8960_sim		MACH_MSM8960_SIM	MSM8960_SIM		3230