Commit 60ff189c authored by Roger Shimizu's avatar Roger Shimizu Committed by Gregory CLEMENT

ARM: dts: kirkwood: split lswvl dts to linkstation lsvl and lswvl

LS-WVL/VL are both kirkwood-6282 based NAS devices, which share
many MPP pins. However they are slightly different:
  - LS-WVL is 2-Bay NAS, and LS-VL is only 1-Bay.
  - There're two red LED indicator on LS-WVL to show when HDD fails,
    which is similar to LS-WXL, but there's no such on LS-VL.

So after the split, common part goes into .dtsi file:
  - kirkwood-linkstation-6282.dtsi
while all rest part goes into device specific .dts file:
  - kirkwood-linkstation-lsvl.dts
  - kirkwood-linkstation-lswvl.dts
Signed-off-by: default avatarRoger Shimizu <rogershimizu@gmail.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarGregory CLEMENT <gregory.clement@free-electrons.com>
parent b05465ff
...@@ -19,10 +19,11 @@ SoC. Currently known SoC compatibles are: ...@@ -19,10 +19,11 @@ SoC. Currently known SoC compatibles are:
And in addition, the compatible shall be extended with the specific And in addition, the compatible shall be extended with the specific
board. Currently known boards are: board. Currently known boards are:
"buffalo,linkstation-lsvl"
"buffalo,linkstation-lswsxl" "buffalo,linkstation-lswsxl"
"buffalo,linkstation-lswxl" "buffalo,linkstation-lswxl"
"buffalo,linkstation-lswvl"
"buffalo,lschlv2" "buffalo,lschlv2"
"buffalo,lswvl"
"buffalo,lsxhl" "buffalo,lsxhl"
"buffalo,lsxl" "buffalo,lsxl"
"cloudengines,pogo02" "cloudengines,pogo02"
......
...@@ -189,10 +189,11 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ ...@@ -189,10 +189,11 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
kirkwood-is2.dtb \ kirkwood-is2.dtb \
kirkwood-km_kirkwood.dtb \ kirkwood-km_kirkwood.dtb \
kirkwood-laplug.dtb \ kirkwood-laplug.dtb \
kirkwood-linkstation-lsvl.dtb \
kirkwood-linkstation-lswsxl.dtb \ kirkwood-linkstation-lswsxl.dtb \
kirkwood-linkstation-lswvl.dtb \
kirkwood-linkstation-lswxl.dtb \ kirkwood-linkstation-lswxl.dtb \
kirkwood-lschlv2.dtb \ kirkwood-lschlv2.dtb \
kirkwood-lswvl.dtb \
kirkwood-lsxhl.dtb \ kirkwood-lsxhl.dtb \
kirkwood-mplcec4.dtb \ kirkwood-mplcec4.dtb \
kirkwood-mv88f6281gtw-ge.dtb \ kirkwood-mv88f6281gtw-ge.dtb \
......
/* /*
* Device Tree file for Buffalo Linkstation LS-WVL/VL * Device Tree common file for kirkwood-6282 based Buffalo Linkstation
* *
* Copyright (C) 2015, 2016 * Copyright (C) 2015, 2016
* Roger Shimizu <rogershimizu@gmail.com> * Roger Shimizu <rogershimizu@gmail.com>
...@@ -43,44 +43,17 @@ ...@@ -43,44 +43,17 @@
* OTHER DEALINGS IN THE SOFTWARE. * OTHER DEALINGS IN THE SOFTWARE.
*/ */
/dts-v1/;
#include "kirkwood.dtsi" #include "kirkwood.dtsi"
#include "kirkwood-6282.dtsi" #include "kirkwood-6282.dtsi"
#include "kirkwood-linkstation.dtsi"
/ { / {
model = "Buffalo Linkstation LS-WVL/VL";
compatible = "buffalo,lswvl", "buffalo,lsvl", "marvell,kirkwood-88f6282", "marvell,kirkwood";
memory { /* 256 MB */
device_type = "memory";
reg = <0x00000000 0x10000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8 earlyprintk";
stdout-path = &uart0;
};
mbus {
pcie-controller {
status = "okay";
pcie@1,0 {
status = "okay";
};
};
};
ocp@f1000000 { ocp@f1000000 {
pinctrl: pin-controller@10000 { pinctrl: pin-controller@10000 {
pmx_power_hdd0: pmx-power-hdd0 { pmx_power_hdd0: pmx-power-hdd0 {
marvell,pins = "mpp8"; marvell,pins = "mpp8";
marvell,function = "gpio"; marvell,function = "gpio";
}; };
pmx_power_hdd1: pmx-power-hdd1 {
marvell,pins = "mpp9";
marvell,function = "gpio";
};
pmx_usb_vbus: pmx-usb-vbus { pmx_usb_vbus: pmx-usb-vbus {
marvell,pins = "mpp12"; marvell,pins = "mpp12";
marvell,function = "gpio"; marvell,function = "gpio";
...@@ -93,14 +66,6 @@ pmx_fan_low: pmx-fan-low { ...@@ -93,14 +66,6 @@ pmx_fan_low: pmx-fan-low {
marvell,pins = "mpp17"; marvell,pins = "mpp17";
marvell,function = "gpio"; marvell,function = "gpio";
}; };
pmx_led_hdderr0: pmx-led-hdderr0 {
marvell,pins = "mpp34";
marvell,function = "gpio";
};
pmx_led_hdderr1: pmx-led-hdderr1 {
marvell,pins = "mpp35";
marvell,function = "gpio";
};
pmx_led_alarm: pmx-led-alarm { pmx_led_alarm: pmx-led-alarm {
marvell,pins = "mpp36"; marvell,pins = "mpp36";
marvell,function = "gpio"; marvell,function = "gpio";
...@@ -138,120 +103,48 @@ pmx_power_auto_switch: pmx-power-auto-switch { ...@@ -138,120 +103,48 @@ pmx_power_auto_switch: pmx-power-auto-switch {
marvell,function = "gpio"; marvell,function = "gpio";
}; };
}; };
serial@12000 {
status = "okay";
};
sata@80000 {
status = "okay";
nr-ports = <2>;
};
spi@10600 {
status = "okay";
m25p40@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "st,m25p40", "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
mode = <0>;
partition@0 {
reg = <0x0 0x60000>;
label = "uboot";
read-only;
};
partition@60000 {
reg = <0x60000 0x10000>;
label = "dtb";
read-only;
};
partition@70000 {
reg = <0x70000 0x10000>;
label = "uboot_env";
};
};
};
}; };
gpio_keys { gpio_keys {
compatible = "gpio-keys"; function-button {
#address-cells = <1>;
#size-cells = <0>;
pinctrl-0 = <&pmx_button_function &pmx_power_switch
&pmx_power_auto_switch>;
pinctrl-names = "default";
button@1 {
label = "Function Button";
linux,code = <KEY_OPTION>;
gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
}; };
button@2 { power-on-switch {
label = "Power-on Switch";
linux,code = <KEY_RESERVED>;
linux,input-type = <5>;
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
}; };
button@3 { power-auto-switch {
label = "Power-auto Switch";
linux,code = <KEY_ESC>;
linux,input-type = <5>;
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
}; };
}; };
gpio_leds { gpio_leds {
compatible = "gpio-leds"; red-alarm-led {
pinctrl-0 = <&pmx_led_function_red &pmx_led_alarm label = "linkstation:red:alarm";
&pmx_led_info &pmx_led_power
&pmx_led_function_blue
&pmx_led_hdderr0
&pmx_led_hdderr1>;
pinctrl-names = "default";
led@1 {
label = "lswvl:red:alarm";
gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
}; };
led@2 { red-function-led {
label = "lswvl:red:func"; label = "linkstation:red:function";
gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
}; };
led@3 { amber-info-led {
label = "lswvl:amber:info"; label = "linkstation:amber:info";
gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
}; };
led@4 { blue-function-led {
label = "lswvl:blue:func"; label = "linkstation:blue:function";
gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
}; };
led@5 { blue-power-led {
label = "lswvl:blue:power"; label = "linkstation:blue:power";
gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
default-state = "keep"; default-state = "keep";
}; };
led@6 {
label = "lswvl:red:hdderr0";
gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
};
led@7 {
label = "lswvl:red:hdderr1";
gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
};
}; };
gpio_fan { gpio_fan {
...@@ -270,50 +163,14 @@ gpio_fan { ...@@ -270,50 +163,14 @@ gpio_fan {
alarm-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; alarm-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
}; };
restart_poweroff {
compatible = "restart-poweroff";
};
regulators { regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
pinctrl-0 = <&pmx_power_hdd0 &pmx_power_hdd1 &pmx_usb_vbus>;
pinctrl-names = "default";
usb_power: regulator@1 { usb_power: regulator@1 {
compatible = "regulator-fixed";
reg = <1>;
regulator-name = "USB Power";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
regulator-always-on;
regulator-boot-on;
gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>; gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
}; };
hdd_power0: regulator@2 { hdd_power0: regulator@2 {
compatible = "regulator-fixed";
reg = <2>;
regulator-name = "HDD0 Power";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
regulator-always-on;
regulator-boot-on;
gpio = <&gpio0 8 GPIO_ACTIVE_HIGH>; gpio = <&gpio0 8 GPIO_ACTIVE_HIGH>;
}; };
hdd_power1: regulator@3 {
compatible = "regulator-fixed";
reg = <3>;
regulator-name = "HDD1 Power";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
regulator-always-on;
regulator-boot-on;
gpio = <&gpio0 9 GPIO_ACTIVE_HIGH>;
};
}; };
}; };
......
/*
* Device Tree file for Buffalo Linkstation LS-VL
*
* Copyright (C) 2015, 2016
* Roger Shimizu <rogershimizu@gmail.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "kirkwood-linkstation-6282.dtsi"
/ {
model = "Buffalo Linkstation LS-VL";
compatible = "buffalo,lsvl", "marvell,kirkwood-88f6282", "marvell,kirkwood";
memory { /* 256 MB */
device_type = "memory";
reg = <0x00000000 0x10000000>;
};
};
/*
* Device Tree file for Buffalo Linkstation LS-WVL
*
* Copyright (C) 2015, 2016
* Roger Shimizu <rogershimizu@gmail.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "kirkwood-linkstation-6282.dtsi"
/ {
model = "Buffalo Linkstation LS-WVL";
compatible = "buffalo,lswvl","marvell,kirkwood-88f6282", "marvell,kirkwood";
memory { /* 256 MB */
device_type = "memory";
reg = <0x00000000 0x10000000>;
};
ocp@f1000000 {
pinctrl: pin-controller@10000 {
pmx_power_hdd1: pmx-power-hdd1 {
marvell,pins = "mpp9";
marvell,function = "gpio";
};
pmx_led_hdderr0: pmx-led-hdderr0 {
marvell,pins = "mpp34";
marvell,function = "gpio";
};
pmx_led_hdderr1: pmx-led-hdderr1 {
marvell,pins = "mpp35";
marvell,function = "gpio";
};
};
sata@80000 {
nr-ports = <2>;
};
};
gpio_leds {
pinctrl-0 = <&pmx_led_function_red &pmx_led_alarm
&pmx_led_info &pmx_led_power
&pmx_led_function_blue
&pmx_led_hdderr0
&pmx_led_hdderr1>;
red-hdderr0-led {
label = "linkstation:red:hdderr0";
gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
};
red-hdderr1-led {
label = "linkstation:red:hdderr1";
gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
};
};
regulators {
pinctrl-0 = <&pmx_power_hdd0 &pmx_power_hdd1 &pmx_usb_vbus>;
hdd_power1: regulator@3 {
compatible = "regulator-fixed";
reg = <3>;
regulator-name = "HDD1 Power";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
regulator-always-on;
regulator-boot-on;
gpio = <&gpio0 9 GPIO_ACTIVE_HIGH>;
};
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment