ide/Kconfig: couple of fixes

* Don't ask to enable no longer existing config options
  ("Use DMA by default when available" and "Special UDMA Feature").

* PIIX host driver doesn't support Victory66 chipset.

* "ide0=cmd640_vlb" -> "cmd640.probe_vlb"

* "ide=doubler" -> "gayle.doubler"

* Amiga IDE doubler support is a feature for gayle host driver
  not a separate host driver.

* Remove Andre's mail.
Signed-off-by: default avatarBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
parent e7f379d5
#
# IDE ATA ATAPI Block device driver configuration
#
# Andre Hedrick <andre@linux-ide.org>
#
# Select HAVE_IDE if IDE is supported
config HAVE_IDE
......@@ -335,7 +333,7 @@ config BLK_DEV_CMD640
This driver will work automatically in PCI based systems (most new
systems have PCI slots). But if your system uses VESA local bus
(VLB) instead of PCI, you must also supply a kernel boot parameter
to enable the CMD640 bugfix/support: "ide0=cmd640_vlb". (Try "man
to enable the CMD640 bugfix/support: "cmd640.probe_vlb". (Try "man
bootparam" or see the documentation of your boot loader about how to
pass options to the kernel.)
......@@ -457,8 +455,7 @@ config BLK_DEV_ALI15X3
onboard chipsets. It also tests for Simplex mode and enables
normal dual channel support.
If you say Y here, you also need to say Y to "Use DMA by default
when available", above. Please read the comments at the top of
Please read the comments at the top of
<file:drivers/ide/pci/alim15x3.c>.
If unsure, say N.
......@@ -505,9 +502,6 @@ config BLK_DEV_CY82C693
This driver adds detection and support for the CY82C693 chipset
used on Digital's PC-Alpha 164SX boards.
If you say Y here, you need to say Y to "Use DMA by default
when available" as well.
config BLK_DEV_CS5520
tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)"
depends on EXPERIMENTAL
......@@ -598,13 +592,12 @@ config BLK_DEV_SC1200
National SCx200 series of embedded x86 "Geode" systems.
config BLK_DEV_PIIX
tristate "Intel PIIXn chipsets support"
tristate "Intel PIIX/ICH chipsets support"
select BLK_DEV_IDEDMA_PCI
help
This driver adds explicit support for Intel PIIX and ICH chips
and also for the Efar Victory66 (slc90e66) chip. This allows
the kernel to change PIO, DMA and UDMA speeds and to configure
the chip to optimum performance.
This driver adds explicit support for Intel PIIX and ICH chips.
This allows the kernel to change PIO, DMA and UDMA speeds and to
configure the chip to optimum performance.
config BLK_DEV_IT8213
tristate "IT8213 IDE support"
......@@ -642,11 +635,7 @@ config BLK_DEV_PDC202XX_OLD
happen if the BIOS revisions of all installed cards (three-max) do
not match, the driver attempts to do dynamic tuning of the chipset
at boot-time for max-speed. Ultra33 BIOS 1.25 or newer is required
for more than one card. This card may require that you say Y to
"Special UDMA Feature".
If you say Y here, you need to say Y to "Use DMA by default when
available" as well.
for more than one card.
Please read the comments at the top of
<file:drivers/ide/pci/pdc202xx_old.c>.
......@@ -695,9 +684,6 @@ config BLK_DEV_SIS5513
ATA100: SiS635, SiS645, SiS650, SiS730, SiS735, SiS740,
SiS745, SiS750
If you say Y here, you need to say Y to "Use DMA by default when
available" as well.
Please read the comments at the top of <file:drivers/ide/pci/sis5513.c>.
config BLK_DEV_SL82C105
......@@ -719,9 +705,6 @@ config BLK_DEV_SLC90E66
and it will handle timing cycles. Since this is an improved
look-a-like to the PIIX4 it should be a nice addition.
If you say Y here, you need to say Y to "Use DMA by default when
available" as well.
Please read the comments at the top of
<file:drivers/ide/pci/slc90e66.c>.
......@@ -873,17 +856,17 @@ config BLK_DEV_IDEDOUBLER
bool "Amiga IDE Doubler support (EXPERIMENTAL)"
depends on BLK_DEV_GAYLE && EXPERIMENTAL
---help---
This driver provides support for the so-called `IDE doublers' (made
This feature provides support for the so-called `IDE doublers' (made
by various manufacturers, e.g. Eyetech) that can be connected to
the on-board IDE interface of some Amiga models. Using such an IDE
doubler, you can connect up to four instead of two IDE devices to
the Amiga's on-board IDE interface.
Note that the normal Amiga Gayle IDE driver may not work correctly
if you have an IDE doubler and don't enable this driver!
if you have an IDE doubler and don't enable this feature!
Say Y if you have an IDE doubler. The driver is enabled at kernel
runtime using the "ide=doubler" kernel boot parameter.
Say Y if you have an IDE doubler. The feature is enabled at kernel
runtime using the "gayle.doubler" kernel boot parameter.
config BLK_DEV_BUDDHA
tristate "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment