USB: ehci tdi : let's tdi_reset set host mode

tdi_reset is already taking care of setting host mode for tdi devices.
Don't duplicate code in platform driver.

Make ehci_halt a nop if the controller is not in host mode (otherwise it 
will fail), and let's ehci_reset do the tdi_reset.
We need to move hcd->has_tt flags before ehci_halt, in order ehci_halt 
knows we are a tdi device.


Before the setup routine was doing :
- put controller in host mode
- ehci_halt
- ehci_init
- hcd->has_tt = 1;
- ehci_reset

Now we do :
- hcd->has_tt = 1;
- ehci_halt
- ehci_init
- ehci_reset

PS : now we handle correctly the device -> host transition.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/usb/host/ehci-fsl.c

@@ -233,8 +233,6 @@ static void mpc83xx_usb_setup(struct usb_hcd *hcd)
 			mpc83xx_setup_phy(ehci, pdata->phy_mode, 1);
 	}
 
-	/* put controller in host mode. */
-	ehci_writel(ehci, 0x00000003, non_ehci + FSL_SOC_USB_USBMODE);
 #ifdef CONFIG_PPC_85xx
 	out_be32(non_ehci + FSL_SOC_USB_PRICTRL, 0x00000008);
 	out_be32(non_ehci + FSL_SOC_USB_AGECNTTHRSH, 0x00000080);
@@ -270,6 +268,8 @@ static int ehci_fsl_setup(struct usb_hcd *hcd)
 	/* cache this readonly data; minimize chip reads */
 	ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
 
+	hcd->has_tt = 1;
+
 	retval = ehci_halt(ehci);
 	if (retval)
 		return retval;
@@ -279,8 +279,6 @@ static int ehci_fsl_setup(struct usb_hcd *hcd)
 	if (retval)
 		return retval;
 
-	hcd->has_tt = 1;
-
 	ehci->sbrn = 0x20;
 
 	ehci_reset(ehci);

drivers/usb/host/ehci-fsl.h

@@ -27,7 +27,6 @@
 #define	PORT_PTS_SERIAL		(3<<30)
 #define PORT_PTS_PTW		(1<<28)
 #define FSL_SOC_USB_PORTSC2	0x188
-#define FSL_SOC_USB_USBMODE	0x1a8
 #define FSL_SOC_USB_SNOOP1	0x400	/* NOTE: big-endian */
 #define FSL_SOC_USB_SNOOP2	0x404	/* NOTE: big-endian */
 #define FSL_SOC_USB_AGECNTTHRSH	0x408	/* NOTE: big-endian */

drivers/usb/host/ehci-hcd.c

@@ -194,6 +194,17 @@ static int handshake (struct ehci_hcd *ehci, void __iomem *ptr,
 	return -ETIMEDOUT;
 }
 
+/* check TDI/ARC silicon is in host mode */
+static int tdi_in_host_mode (struct ehci_hcd *ehci)
+{
+	u32 __iomem	*reg_ptr;
+	u32		tmp;
+
+	reg_ptr = (u32 __iomem *)(((u8 __iomem *)ehci->regs) + USBMODE);
+	tmp = ehci_readl(ehci, reg_ptr);
+	return (tmp & 3) == USBMODE_CM_HC;
+}
+
 /* force HC to halt state from unknown (EHCI spec section 2.3) */
 static int ehci_halt (struct ehci_hcd *ehci)
 {
@@ -202,6 +213,10 @@ static int ehci_halt (struct ehci_hcd *ehci)
 	/* disable any irqs left enabled by previous code */
 	ehci_writel(ehci, 0, &ehci->regs->intr_enable);
 
+	if (ehci_is_TDI(ehci) && tdi_in_host_mode(ehci) == 0) {
+		return 0;
+	}
+
 	if ((temp & STS_HALT) != 0)
 		return 0;
 

drivers/usb/host/ehci-mxc.c

@@ -26,9 +26,6 @@
 #include <mach/mxc_ehci.h>
 
 #define ULPI_VIEWPORT_OFFSET	0x170
-#define PORTSC_OFFSET		0x184
-#define USBMODE_OFFSET		0x1a8
-#define USBMODE_CM_HOST		3
 
 struct ehci_mxc_priv {
 	struct clk *usbclk, *ahbclk;
@@ -51,6 +48,8 @@ static int ehci_mxc_setup(struct usb_hcd *hcd)
 	/* cache this readonly data; minimize chip reads */
 	ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
 
+	hcd->has_tt = 1;
+
 	retval = ehci_halt(ehci);
 	if (retval)
 		return retval;
@@ -60,8 +59,6 @@ static int ehci_mxc_setup(struct usb_hcd *hcd)
 	if (retval)
 		return retval;
 
-	hcd->has_tt = 1;
-
 	ehci->sbrn = 0x20;
 
 	ehci_reset(ehci);
@@ -191,12 +188,8 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
 		clk_enable(priv->ahbclk);
 	}
 
-	/* set USBMODE to host mode */
-	temp = readl(hcd->regs + USBMODE_OFFSET);
-	writel(temp | USBMODE_CM_HOST, hcd->regs + USBMODE_OFFSET);
-
 	/* set up the PORTSCx register */
-	writel(pdata->portsc, hcd->regs + PORTSC_OFFSET);
+	ehci_writel(ehci, pdata->portsc, &ehci->regs->port_status[0]);
 	mdelay(10);
 
 	/* setup specific usb hw */