net: Add MOXA ART SoCs ethernet driver

The MOXA UC-711X hardware(s) has an ethernet controller that seem
to be developed internally. The IC used is "RTL8201CP".

Since there is no public documentation, this driver is mostly the
one published by MOXA that has been heavily cleaned up / ported
from linux 2.6.9.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/moxa,moxart-mac.txt

+MOXA ART Ethernet Controller
+
+Required properties:
+
+- compatible : Must be "moxa,moxart-mac"
+- reg : Should contain register location and length
+- interrupts : Should contain the mac interrupt number
+
+Example:
+
+	mac0: mac@90900000 {
+		compatible = "moxa,moxart-mac";
+		reg =	<0x90900000 0x100>;
+		interrupts = <25 0>;
+	};
+
+	mac1: mac@92000000 {
+		compatible = "moxa,moxart-mac";
+		reg =	<0x92000000 0x100>;
+		interrupts = <27 0>;
+	};

drivers/net/ethernet/Kconfig

@@ -90,6 +90,7 @@ source "drivers/net/ethernet/marvell/Kconfig"
 source "drivers/net/ethernet/mellanox/Kconfig"
 source "drivers/net/ethernet/micrel/Kconfig"
 source "drivers/net/ethernet/microchip/Kconfig"
+source "drivers/net/ethernet/moxa/Kconfig"
 source "drivers/net/ethernet/myricom/Kconfig"
 
 config FEALNX

drivers/net/ethernet/Makefile

@@ -42,6 +42,7 @@ obj-$(CONFIG_NET_VENDOR_MARVELL) += marvell/
 obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/
 obj-$(CONFIG_NET_VENDOR_MICREL) += micrel/
 obj-$(CONFIG_NET_VENDOR_MICROCHIP) += microchip/
+obj-$(CONFIG_NET_VENDOR_MOXART) += moxa/
 obj-$(CONFIG_NET_VENDOR_MYRI) += myricom/
 obj-$(CONFIG_FEALNX) += fealnx.o
 obj-$(CONFIG_NET_VENDOR_NATSEMI) += natsemi/

drivers/net/ethernet/moxa/Kconfig

+#
+# MOXART device configuration
+#
+
+config NET_VENDOR_MOXART
+	bool "MOXA ART devices"
+	default y
+	depends on (ARM && ARCH_MOXART)
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about MOXA ART devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_MOXART
+
+config ARM_MOXART_ETHER
+	tristate "MOXART Ethernet support"
+	depends on ARM && ARCH_MOXART
+	select NET_CORE
+	---help---
+	  If you wish to compile a kernel for a hardware with MOXA ART SoC and
+	  want to use the internal ethernet then you should answer Y to this.
+
+
+endif # NET_VENDOR_MOXART

drivers/net/ethernet/moxa/Makefile

+#
+# Makefile for the MOXART network device drivers.
+#
+
+obj-$(CONFIG_ARM_MOXART_ETHER) += moxart_ether.o