Commit 6e897d03 authored by Bill Kuzeja's avatar Bill Kuzeja Committed by Greg Kroah-Hartman

scsi: qla2xxx: Fix scsi scan hang triggered if adapter fails during init

commit a5dd506e upstream.

A system can get hung task timeouts if a qlogic board fails during
initialization (if the board breaks again or fails the init). The hang
involves the scsi scan.

In a nutshell, since commit beb9e315 ("qla2xxx: Prevent removal and
board_disable race"):

...it is possible to have freed ha (base_vha->hw) early by a call to
qla2x00_remove_one when pdev->enable_cnt equals zero:

       if (!atomic_read(&pdev->enable_cnt)) {
               scsi_host_put(base_vha->host);
               kfree(ha);
               pci_set_drvdata(pdev, NULL);
               return;

Almost always, the scsi_host_put above frees the vha structure
(attached to the end of the Scsi_Host we're putting) since it's the last
put, and life is good.  However, if we are entering this routine because
the adapter has broken sometime during initialization AND a scsi scan is
already in progress (and has done its own scsi_host_get), vha will not
be freed. What's worse, the scsi scan will access the freed ha structure
through qla2xxx_scan_finished:

        if (time > vha->hw->loop_reset_delay * HZ)
                return 1;

The scsi scan keeps checking to see if a scan is complete by calling
qla2xxx_scan_finished. There is a timeout value that limits the length
of time a scan can take (hw->loop_reset_delay, usually set to 5
seconds), but this definition is in the data structure (hw) that can get
freed early.

This can yield unpredictable results, the worst of which is that the
scsi scan can hang indefinitely. This happens when the freed structure
gets reused and loop_reset_delay gets overwritten with garbage, which
the scan obliviously uses as its timeout value.

The fix for this is simple: at the top of qla2xxx_scan_finished, check
for the UNLOADING bit in the vha structure (_vha is not freed at this
point).  If UNLOADING is set, we exit the scan for this adapter
immediately. After this last reference to the ha structure, we'll exit
the scan for this adapter, and continue on.

This problem is hard to hit, but I have run into it doing negative
testing many times now (with a test specifically designed to bring it
out), so I can verify that this fix works. My testing has been against a
RHEL7 driver variant, but the bug and patch are equally relevant to to
the upstream driver.

Fixes: beb9e315 ("qla2xxx: Prevent removal and board_disable race")
Signed-off-by: default avatarBill Kuzeja <william.kuzeja@stratus.com>
Acked-by: default avatarHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: default avatarMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 29cf142c
......@@ -2257,6 +2257,8 @@ qla2xxx_scan_finished(struct Scsi_Host *shost, unsigned long time)
{
scsi_qla_host_t *vha = shost_priv(shost);
if (test_bit(UNLOADING, &vha->dpc_flags))
return 1;
if (!vha->host)
return 1;
if (time > vha->hw->loop_reset_delay * HZ)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment