Commit 72edd84a authored by Lennert Buytenhek's avatar Lennert Buytenhek Committed by Russell King

[ARM] 3827/1: iop3xx: add common gpio module

Implement the gpio_line_{config,get,set} API for iop3xx.
Signed-off-by: default avatarLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: default avatarRussell King <rmk+kernel@arm.linux.org.uk>
parent 610300e8
......@@ -2,7 +2,7 @@
# Makefile for the linux kernel.
#
obj-y := i2c.o pci.o setup.o time.o
obj-y := gpio.o i2c.o pci.o setup.o time.o
obj-m :=
obj-n :=
obj- :=
/*
* arch/arm/plat-iop/gpio.c
* GPIO handling for Intel IOP3xx processors.
*
* Copyright (C) 2006 Lennert Buytenhek <buytenh@wantstofly.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or (at
* your option) any later version.
*/
#include <linux/device.h>
#include <asm/hardware/iop3xx.h>
void gpio_line_config(int line, int direction)
{
unsigned long flags;
local_irq_save(flags);
if (direction == GPIO_IN) {
*IOP3XX_GPOE |= 1 << line;
} else if (direction == GPIO_OUT) {
*IOP3XX_GPOE &= ~(1 << line);
}
local_irq_restore(flags);
}
EXPORT_SYMBOL(gpio_line_config);
int gpio_line_get(int line)
{
return !!(*IOP3XX_GPID & (1 << line));
}
EXPORT_SYMBOL(gpio_line_get);
void gpio_line_set(int line, int value)
{
unsigned long flags;
local_irq_save(flags);
if (value == GPIO_LOW) {
*IOP3XX_GPOD &= ~(1 << line);
} else if (value == GPIO_HIGH) {
*IOP3XX_GPOD |= 1 << line;
}
local_irq_restore(flags);
}
EXPORT_SYMBOL(gpio_line_set);
......@@ -82,14 +82,16 @@ iop3xx_i2c_enable(struct i2c_algo_iop3xx_data *iop3xx_adap)
/*
* Every time unit enable is asserted, GPOD needs to be cleared
* on IOP32X to avoid data corruption on the bus.
* on IOP3XX to avoid data corruption on the bus.
*/
#ifdef CONFIG_ARCH_IOP32X
#define IOP321_GPOD_I2C0 0x00c0 /* clear these bits to enable ch0 */
#define IOP321_GPOD_I2C1 0x0030 /* clear these bits to enable ch1 */
*IOP321_GPOD &= (iop3xx_adap->id == 0) ? ~IOP321_GPOD_I2C0 :
~IOP321_GPOD_I2C1;
#ifdef CONFIG_PLAT_IOP
if (iop3xx_adap->id == 0) {
gpio_line_set(IOP3XX_GPIO_LINE(7), GPIO_LOW);
gpio_line_set(IOP3XX_GPIO_LINE(6), GPIO_LOW);
} else {
gpio_line_set(IOP3XX_GPIO_LINE(5), GPIO_LOW);
gpio_line_set(IOP3XX_GPIO_LINE(4), GPIO_LOW);
}
#endif
/* NB SR bits not same position as CR IE bits :-( */
iop3xx_adap->SR_enabled =
......
......@@ -216,6 +216,7 @@
* Peripherals that are shared between the iop32x and iop33x but
* located at different addresses.
*/
#define IOP3XX_GPIO_REG(reg) (IOP3XX_PERIPHERAL_VIRT_BASE + 0x07c0 + (reg))
#define IOP3XX_TIMER_REG(reg) (IOP3XX_PERIPHERAL_VIRT_BASE + 0x07e0 + (reg))
#include <asm/hardware/iop3xx.h>
......
......@@ -221,6 +221,7 @@
* Peripherals that are shared between the iop32x and iop33x but
* located at different addresses.
*/
#define IOP3XX_GPIO_REG(reg) (IOP3XX_PERIPHERAL_VIRT_BASE + 0x1780 + (reg))
#define IOP3XX_TIMER_REG(reg) (IOP3XX_PERIPHERAL_VIRT_BASE + 0x07d0 + (reg))
#include <asm/hardware/iop3xx.h>
......
......@@ -15,6 +15,22 @@
#ifndef __IOP3XX_H
#define __IOP3XX_H
/*
* IOP3XX GPIO handling
*/
#define GPIO_IN 0
#define GPIO_OUT 1
#define GPIO_LOW 0
#define GPIO_HIGH 1
#define IOP3XX_GPIO_LINE(x) (x)
#ifndef __ASSEMBLY__
extern void gpio_line_config(int line, int direction);
extern int gpio_line_get(int line);
extern void gpio_line_set(int line, int value);
#endif
/*
* IOP3XX processor registers
*/
......@@ -81,6 +97,11 @@
#define IOP3XX_PCIXSR (volatile u32 *)IOP3XX_REG_ADDR(0x01e4)
#define IOP3XX_PCIIRSR (volatile u32 *)IOP3XX_REG_ADDR(0x01ec)
/* General Purpose I/O */
#define IOP3XX_GPOE (volatile u32 *)IOP3XX_GPIO_REG(0x0004)
#define IOP3XX_GPID (volatile u32 *)IOP3XX_GPIO_REG(0x0008)
#define IOP3XX_GPOD (volatile u32 *)IOP3XX_GPIO_REG(0x000c)
/* Timers */
#define IOP3XX_TU_TMR0 (volatile u32 *)IOP3XX_TIMER_REG(0x0000)
#define IOP3XX_TU_TMR1 (volatile u32 *)IOP3XX_TIMER_REG(0x0004)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment