arm64: dts: renesas: hihope-common: Add USB 2.0 support

Add USB 2.0 support to the HiHope RZ/G2M.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arch/arm64/boot/dts/renesas/hihope-common.dtsi

@@ -35,6 +35,17 @@ reg_3p3v: regulator1 {
 		regulator-always-on;
 	};
 
+	vbus0_usb2: regulator-vbus0-usb2 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB20_VBUS0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	vccq_sdhi0: regulator-vccq-sdhi0 {
 		compatible = "regulator-gpio";
 
@@ -49,6 +60,14 @@ vccq_sdhi0: regulator-vccq-sdhi0 {
 	};
 };
 
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
 &extal_clk {
 	clock-frequency = <16666666>;
 };
@@ -57,6 +76,28 @@ &extalr_clk {
 	clock-frequency = <32768>;
 };
 
+&gpio6 {
+	usb1-reset {
+		gpio-hog;
+		gpios = <10 GPIO_ACTIVE_LOW>;
+		output-low;
+		line-name = "usb1-reset";
+	};
+};
+
+&hsusb {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
 &pcie_bus_clk {
 	clock-frequency = <100000000>;
 };
@@ -92,6 +133,23 @@ sdhi3_pins: sd3 {
 		function = "sdhi3";
 		power-source = <1800>;
 	};
+
+	usb0_pins: usb0 {
+		groups = "usb0";
+		function = "usb0";
+	};
+
+	usb1_pins: usb1 {
+		mux {
+			groups = "usb1";
+			function = "usb1";
+		};
+
+		ovc {
+			pins = "GP_6_27";
+			bias-pull-up;
+		};
+	};
 };
 
 &rwdt {
@@ -135,5 +193,23 @@ &sdhi3 {
 	mmc-hs200-1_8v;
 	non-removable;
 	fixed-emmc-driver-type = <1>;
+};
+
+&usb_extal_clk {
+	clock-frequency = <50000000>;
+};
+
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+
+	vbus-supply = <&vbus0_usb2>;
+	status = "okay";
+};
+
+&usb2_phy1 {
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+
 	status = "okay";
 };