Merge branch 'for-4.12/dax' into libnvdimm-for-next

Documentation/DocBook/rapidio.tmpl

@@ -128,9 +128,6 @@
      </sect1>
      <sect1 id="Device_model_support"><title>Device model support</title>
 !Idrivers/rapidio/rio-driver.c
-     </sect1>
-     <sect1 id="Sysfs_support"><title>Sysfs support</title>
-!Idrivers/rapidio/rio-sysfs.c
      </sect1>
      <sect1 id="PPC32_support"><title>PPC32 support</title>
 !Iarch/powerpc/sysdev/fsl_rio.c

Documentation/devicetree/bindings/auxdisplay/hit,hd44780.txt

+DT bindings for the Hitachi HD44780 Character LCD Controller
+
+The Hitachi HD44780 Character LCD Controller is commonly used on character LCDs
+that can display one or more lines of text. It exposes an M6800 bus interface,
+which can be used in either 4-bit or 8-bit mode.
+
+Required properties:
+  - compatible: Must contain "hit,hd44780",
+  - data-gpios: Must contain an array of either 4 or 8 GPIO specifiers,
+    referring to the GPIO pins connected to the data signal lines DB0-DB7
+    (8-bit mode) or DB4-DB7 (4-bit mode) of the LCD Controller's bus interface,
+  - enable-gpios: Must contain a GPIO specifier, referring to the GPIO pin
+    connected to the "E" (Enable) signal line of the LCD Controller's bus
+    interface,
+  - rs-gpios: Must contain a GPIO specifier, referring to the GPIO pin
+    connected to the "RS" (Register Select) signal line of the LCD Controller's
+    bus interface,
+  - display-height: Height of the display, in character cells,
+  - display-width: Width of the display, in character cells.
+
+Optional properties:
+  - rw-gpios: Must contain a GPIO specifier, referring to the GPIO pin
+    connected to the "RW" (Read/Write) signal line of the LCD Controller's bus
+    interface,
+  - backlight-gpios: Must contain a GPIO specifier, referring to the GPIO pin
+    used for enabling the LCD's backlight,
+  - internal-buffer-width: Internal buffer width (default is 40 for displays
+    with 1 or 2 lines, and display-width for displays with more than 2 lines).
+
+Example:
+
+	auxdisplay {
+		compatible = "hit,hd44780";
+
+		data-gpios = <&hc595 0 GPIO_ACTIVE_HIGH>,
+			     <&hc595 1 GPIO_ACTIVE_HIGH>,
+			     <&hc595 2 GPIO_ACTIVE_HIGH>,
+			     <&hc595 3 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
+		rs-gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
+
+		display-height = <2>;
+		display-width = <16>;
+	};

Documentation/devicetree/bindings/fpga/fpga-region.txt

@@ -186,6 +186,7 @@ Optional properties:
 	otherwise full reconfiguration is done.
 - external-fpga-config : boolean, set if the FPGA has already been configured
 	prior to OS boot up.
+- encrypted-fpga-config : boolean, set if the bitstream is encrypted
 - region-unfreeze-timeout-us : The maximum time in microseconds to wait for
 	bridges to successfully become enabled after the region has been
 	programmed.

Documentation/devicetree/bindings/fpga/lattice-ice40-fpga-mgr.txt

+Lattice iCE40 FPGA Manager
+
+Required properties:
+- compatible:		Should contain "lattice,ice40-fpga-mgr"
+- reg:			SPI chip select
+- spi-max-frequency:	Maximum SPI frequency (>=1000000, <=25000000)
+- cdone-gpios:		GPIO input connected to CDONE pin
+- reset-gpios:		Active-low GPIO output connected to CRESET_B pin. Note
+			that unless the GPIO is held low during startup, the
+			FPGA will enter Master SPI mode and drive SCK with a
+			clock signal potentially jamming other devices on the
+			bus until the firmware is loaded.
+
+Example:
+	fpga: fpga@0 {
+		compatible = "lattice,ice40-fpga-mgr";
+		reg = <0>;
+		spi-max-frequency = <1000000>;
+		cdone-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+	};

Documentation/w1/slaves/00-INDEX

@@ -2,7 +2,11 @@
 	- This file
 w1_therm
 	- The Maxim/Dallas Semiconductor ds18*20 temperature sensor.
+w1_ds2413
+	- The Maxim/Dallas Semiconductor ds2413 dual channel addressable switch.
 w1_ds2423
 	- The Maxim/Dallas Semiconductor ds2423 counter device.
+w1_ds2438
+	- The Maxim/Dallas Semiconductor ds2438 smart battery monitor.
 w1_ds28e04
 	- The Maxim/Dallas Semiconductor ds28e04 eeprom.

Documentation/w1/slaves/w1_ds2413

+Kernel driver w1_ds2413
+=======================
+
+Supported chips:
+  * Maxim DS2413 1-Wire Dual Channel Addressable Switch
+
+supported family codes:
+        W1_FAMILY_DS2413        0x3A
+
+Author: Mariusz Bialonczyk <manio@skyboo.net>
+
+Description
+-----------
+
+The DS2413 chip has two open-drain outputs (PIO A and PIO B).
+Support is provided through the sysfs files "output" and "state".
+
+Reading state
+-------------
+The "state" file provides one-byte value which is in the same format as for
+the chip PIO_ACCESS_READ command (refer the datasheet for details):
+
+Bit 0:   PIOA Pin State
+Bit 1:   PIOA Output Latch State
+Bit 2:   PIOB Pin State
+Bit 3:   PIOB Output Latch State
+Bit 4-7: Complement of Bit 3 to Bit 0 (verified by the kernel module)
+
+This file is readonly.
+
+Writing output
+--------------
+You can set the PIO pins using the "output" file.
+It is writable, you can write one-byte value to this sysfs file.
+Similarly the byte format is the same as for the PIO_ACCESS_WRITE command:
+
+Bit 0:   PIOA
+Bit 1:   PIOB
+Bit 2-7: No matter (driver will set it to "1"s)
+
+
+The chip has some kind of basic protection against transmission errors.
+When reading the state, there is a four complement bits.
+The driver is checking this complement, and when it is wrong then it is
+returning I/O error.
+
+When writing output, the master must repeat the PIO Output Data byte in
+its inverted form and it is waiting for a confirmation.
+If the write is unsuccessful for three times, the write also returns
+I/O error.

Documentation/w1/slaves/w1_ds2438

+Kernel driver w1_ds2438
+=======================
+
+Supported chips:
+  * Maxim DS2438 Smart Battery Monitor
+
+supported family codes:
+        W1_FAMILY_DS2438        0x26
+
+Author: Mariusz Bialonczyk <manio@skyboo.net>
+
+Description
+-----------
+
+The DS2438 chip provides several functions that are desirable to carry in
+a battery pack. It also has a 40 bytes of nonvolatile EEPROM.
+Because the ability of temperature, current and voltage measurement, the chip
+is also often used in weather stations and applications such as: rain gauge,
+wind speed/direction measuring, humidity sensing, etc.
+
+Current support is provided through the following sysfs files (all files
+except "iad" are readonly):
+
+"iad"
+-----
+This file controls the 'Current A/D Control Bit' (IAD) in the
+Status/Configuration Register.
+Writing a zero value will clear the IAD bit and disables the current
+measurements.
+Writing value "1" is setting the IAD bit (enables the measurements).
+The IAD bit is enabled by default in the DS2438.
+
+When writing to sysfs file bits 2-7 are ignored, so it's safe to write ASCII.
+An I/O error is returned when there is a problem setting the new value.
+
+"page0"
+-------
+This file provides full 8 bytes of the chip Page 0 (00h).
+This page contains the most frequently accessed information of the DS2438.
+Internally when this file is read, the additional CRC byte is also obtained
+from the slave device. If it is correct, the 8 bytes page data are passed
+to userspace, otherwise an I/O error is returned.
+
+"temperature"
+-------------
+Opening and reading this file initiates the CONVERT_T (temperature conversion)
+command of the chip, afterwards the temperature is read from the device
+registers and provided as an ASCII decimal value.
+
+Important: The returned value has to be divided by 256 to get a real
+temperature in degrees Celsius.
+
+"vad", "vdd"
+------------
+Opening and reading this file initiates the CONVERT_V (voltage conversion)
+command of the chip.
+
+Depending on a sysfs filename a different input for the A/D will be selected:
+vad: general purpose A/D input (VAD)
+vdd: battery input (VDD)
+
+After the voltage conversion the value is returned as decimal ASCII.
+Note: The value is in mV, so to get a volts the value has to be divided by 10.

MAINTAINERS

@@ -5109,7 +5109,6 @@ F:	include/uapi/linux/firewire*.h
 F:	tools/firewire/
 
 FIRMWARE LOADER (request_firmware)
-M:	Ming Lei <ming.lei@canonical.com>
 M:	Luis R. Rodriguez <mcgrof@kernel.org>
 L:	linux-kernel@vger.kernel.org
 S:	Maintained

arch/arm/mach-ep93xx/ts72xx.c

@@ -210,6 +210,28 @@ static struct ep93xx_eth_data __initdata ts72xx_eth_data = {
 	.phy_id		= 1,
 };
 
+#if IS_ENABLED(CONFIG_FPGA_MGR_TS73XX)
+
+/* Relative to EP93XX_CS1_PHYS_BASE */
+#define TS73XX_FPGA_LOADER_BASE		0x03c00000
+
+static struct resource ts73xx_fpga_resources[] = {
+	{
+		.start	= EP93XX_CS1_PHYS_BASE + TS73XX_FPGA_LOADER_BASE,
+		.end	= EP93XX_CS1_PHYS_BASE + TS73XX_FPGA_LOADER_BASE + 1,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device ts73xx_fpga_device = {
+	.name	= "ts73xx-fpga-mgr",
+	.id	= -1,
+	.resource = ts73xx_fpga_resources,
+	.num_resources = ARRAY_SIZE(ts73xx_fpga_resources),
+};
+
+#endif
+
 static void __init ts72xx_init_machine(void)
 {
 	ep93xx_init_devices();
@@ -218,6 +240,10 @@ static void __init ts72xx_init_machine(void)
 	platform_device_register(&ts72xx_wdt_device);
 
 	ep93xx_register_eth(&ts72xx_eth_data, 1);
+#if IS_ENABLED(CONFIG_FPGA_MGR_TS73XX)
+	if (board_is_ts7300())
+		platform_device_register(&ts73xx_fpga_device);
+#endif
 }
 
 MACHINE_START(TS72XX, "Technologic Systems TS-72xx SBC")

arch/powerpc/platforms/Kconfig

@@ -284,6 +284,7 @@ config CPM2
 config AXON_RAM
 	tristate "Axon DDR2 memory device driver"
 	depends on PPC_IBM_CELL_BLADE && BLOCK
+	select DAX
 	default m
 	help
 	  It registers one block device per Axon's DDR2 memory bank found

arch/powerpc/sysdev/axonram.c

@@ -25,6 +25,7 @@
 
 #include <linux/bio.h>
 #include <linux/blkdev.h>
+#include <linux/dax.h>
 #include <linux/device.h>
 #include <linux/errno.h>
 #include <linux/fs.h>
@@ -62,6 +63,7 @@ static int azfs_major, azfs_minor;
 struct axon_ram_bank {
 	struct platform_device	*device;
 	struct gendisk		*disk;
+	struct dax_device	*dax_dev;
 	unsigned int		irq_id;
 	unsigned long		ph_addr;
 	unsigned long		io_addr;
@@ -137,25 +139,32 @@ axon_ram_make_request(struct request_queue *queue, struct bio *bio)
 	return BLK_QC_T_NONE;
 }
 
-/**
- * axon_ram_direct_access - direct_access() method for block device
- * @device, @sector, @data: see block_device_operations method
- */
+static const struct block_device_operations axon_ram_devops = {
+	.owner		= THIS_MODULE,
+};
+
 static long
-axon_ram_direct_access(struct block_device *device, sector_t sector,
-		       void **kaddr, pfn_t *pfn, long size)
+__axon_ram_direct_access(struct axon_ram_bank *bank, pgoff_t pgoff, long nr_pages,
+		       void **kaddr, pfn_t *pfn)
 {
-	struct axon_ram_bank *bank = device->bd_disk->private_data;
-	loff_t offset = (loff_t)sector << AXON_RAM_SECTOR_SHIFT;
+	resource_size_t offset = pgoff * PAGE_SIZE;
 
 	*kaddr = (void *) bank->io_addr + offset;
 	*pfn = phys_to_pfn_t(bank->ph_addr + offset, PFN_DEV);
-	return bank->size - offset;
+	return (bank->size - offset) / PAGE_SIZE;
 }
 
-static const struct block_device_operations axon_ram_devops = {
-	.owner		= THIS_MODULE,
-	.direct_access	= axon_ram_direct_access
+static long
+axon_ram_dax_direct_access(struct dax_device *dax_dev, pgoff_t pgoff, long nr_pages,
+		       void **kaddr, pfn_t *pfn)
+{
+	struct axon_ram_bank *bank = dax_get_private(dax_dev);
+
+	return __axon_ram_direct_access(bank, pgoff, nr_pages, kaddr, pfn);
+}
+
+static const struct dax_operations axon_ram_dax_ops = {
+	.direct_access = axon_ram_dax_direct_access,
 };
 
 /**
@@ -219,6 +228,7 @@ static int axon_ram_probe(struct platform_device *device)
 		goto failed;
 	}
 
+
 	bank->disk->major = azfs_major;
 	bank->disk->first_minor = azfs_minor;
 	bank->disk->fops = &axon_ram_devops;
@@ -227,6 +237,13 @@ static int axon_ram_probe(struct platform_device *device)
 	sprintf(bank->disk->disk_name, "%s%d",
 			AXON_RAM_DEVICE_NAME, axon_ram_bank_id);
 
+	bank->dax_dev = alloc_dax(bank, bank->disk->disk_name,
+			&axon_ram_dax_ops);
+	if (!bank->dax_dev) {
+		rc = -ENOMEM;
+		goto failed;
+	}
+
 	bank->disk->queue = blk_alloc_queue(GFP_KERNEL);
 	if (bank->disk->queue == NULL) {
 		dev_err(&device->dev, "Cannot register disk queue\n");
@@ -278,6 +295,8 @@ static int axon_ram_probe(struct platform_device *device)
 				del_gendisk(bank->disk);
 			put_disk(bank->disk);
 		}
+		kill_dax(bank->dax_dev);
+		put_dax(bank->dax_dev);
 		device->dev.platform_data = NULL;
 		if (bank->io_addr != 0)
 			iounmap((void __iomem *) bank->io_addr);
@@ -300,6 +319,8 @@ axon_ram_remove(struct platform_device *device)
 
 	device_remove_file(&device->dev, &dev_attr_ecc);
 	free_irq(bank->irq_id, device);
+	kill_dax(bank->dax_dev);
+	put_dax(bank->dax_dev);
 	del_gendisk(bank->disk);
 	put_disk(bank->disk);
 	iounmap((void __iomem *) bank->io_addr);

arch/x86/hyperv/hv_init.c

@@ -25,7 +25,7 @@
 #include <linux/vmalloc.h>
 #include <linux/mm.h>
 #include <linux/clockchips.h>
-
+#include <linux/hyperv.h>
 
 #ifdef CONFIG_X86_64
 

arch/x86/include/asm/pmem.h

@@ -44,11 +44,6 @@ static inline void arch_memcpy_to_pmem(void *dst, const void *src, size_t n)
 		BUG();
 }
 
-static inline int arch_memcpy_from_pmem(void *dst, const void *src, size_t n)
-{
-	return memcpy_mcsafe(dst, src, n);
-}
-
 /**
  * arch_wb_cache_pmem - write back a cache range with CLWB
  * @vaddr:	virtual start address

arch/x86/include/asm/string_64.h

@@ -79,6 +79,7 @@ int strcmp(const char *cs, const char *ct);
 #define memset(s, c, n) __memset(s, c, n)
 #endif
 
+#define __HAVE_ARCH_MEMCPY_MCSAFE 1
 __must_check int memcpy_mcsafe_unrolled(void *dst, const void *src, size_t cnt);
 DECLARE_STATIC_KEY_FALSE(mcsafe_key);
 

arch/x86/include/uapi/asm/hyperv.h

@@ -124,7 +124,7 @@
   * Recommend using hypercall for address space switches rather
   * than MOV to CR3 instruction
   */
-#define HV_X64_MWAIT_RECOMMENDED		(1 << 0)
+#define HV_X64_AS_SWITCH_RECOMMENDED		(1 << 0)
 /* Recommend using hypercall for local TLB flushes rather
  * than INVLPG or MOV to CR3 instructions */
 #define HV_X64_LOCAL_TLB_FLUSH_RECOMMENDED	(1 << 1)
@@ -147,6 +147,11 @@
  */
 #define HV_X64_RELAXED_TIMING_RECOMMENDED	(1 << 5)
 
+/*
+ * Virtual APIC support
+ */
+#define HV_X64_DEPRECATING_AEOI_RECOMMENDED	(1 << 9)
+
 /*
  * Crash notification flag.
  */

block/Kconfig

@@ -6,6 +6,7 @@ menuconfig BLOCK
        default y
        select SBITMAP
        select SRCU
+       select DAX
        help
 	 Provide block layer support for the kernel.
 

block/partition-generic.c

@@ -16,7 +16,6 @@
 #include <linux/kmod.h>
 #include <linux/ctype.h>
 #include <linux/genhd.h>
-#include <linux/dax.h>
 #include <linux/blktrace_api.h>
 
 #include "partitions/check.h"
@@ -631,24 +630,12 @@ int invalidate_partitions(struct gendisk *disk, struct block_device *bdev)
 	return 0;
 }
 
-static struct page *read_pagecache_sector(struct block_device *bdev, sector_t n)
-{
-	struct address_space *mapping = bdev->bd_inode->i_mapping;
-
-	return read_mapping_page(mapping, (pgoff_t)(n >> (PAGE_SHIFT-9)),
-				 NULL);
-}
-
 unsigned char *read_dev_sector(struct block_device *bdev, sector_t n, Sector *p)
 {
+	struct address_space *mapping = bdev->bd_inode->i_mapping;
 	struct page *page;
 
-	/* don't populate page cache for dax capable devices */
-	if (IS_DAX(bdev->bd_inode))
-		page = read_dax_sector(bdev, n);
-	else
-		page = read_pagecache_sector(bdev, n);
-
+	page = read_mapping_page(mapping, (pgoff_t)(n >> (PAGE_SHIFT-9)), NULL);
 	if (!IS_ERR(page)) {
 		if (PageError(page))
 			goto fail;

drivers/Makefile

@@ -71,7 +71,7 @@ obj-$(CONFIG_PARPORT)		+= parport/
 obj-$(CONFIG_NVM)		+= lightnvm/
 obj-y				+= base/ block/ misc/ mfd/ nfc/
 obj-$(CONFIG_LIBNVDIMM)		+= nvdimm/
-obj-$(CONFIG_DEV_DAX)		+= dax/
+obj-$(CONFIG_DAX)		+= dax/
 obj-$(CONFIG_DMA_SHARED_BUFFER) += dma-buf/
 obj-$(CONFIG_NUBUS)		+= nubus/
 obj-y				+= macintosh/

drivers/acpi/nfit/core.c

@@ -1849,8 +1849,7 @@ static int acpi_nfit_blk_single_io(struct nfit_blk *nfit_blk,
 				mmio_flush_range((void __force *)
 					mmio->addr.aperture + offset, c);
 
-			memcpy_from_pmem(iobuf + copied,
-					mmio->addr.aperture + offset, c);
+			memcpy(iobuf + copied, mmio->addr.aperture + offset, c);
 		}
 
 		copied += c;

drivers/android/Kconfig

@@ -22,7 +22,7 @@ config ANDROID_BINDER_IPC
 config ANDROID_BINDER_DEVICES
 	string "Android Binder devices"
 	depends on ANDROID_BINDER_IPC
-	default "binder"
+	default "binder,hwbinder"
 	---help---
 	  Default value for the binder.devices parameter.
 

drivers/auxdisplay/Kconfig

@@ -13,8 +13,22 @@ menuconfig AUXDISPLAY
 
 	  If you say N, all options in this submenu will be skipped and disabled.
 
+config CHARLCD
+	tristate "Character LCD core support" if COMPILE_TEST
+
 if AUXDISPLAY
 
+config HD44780
+	tristate "HD44780 Character LCD support"
+	depends on GPIOLIB || COMPILE_TEST
+	select CHARLCD
+	---help---
+	  Enable support for Character LCDs using a HD44780 controller.
+	  The LCD is accessible through the /dev/lcd char device (10, 156).
+	  This code can either be compiled as a module, or linked into the
+	  kernel and started at boot.
+	  If you don't understand what all this is about, say N.
+
 config KS0108
 	tristate "KS0108 LCD Controller"
 	depends on PARPORT_PC

drivers/auxdisplay/Makefile

@@ -2,7 +2,9 @@
 # Makefile for the kernel auxiliary displays device drivers.
 #
 
+obj-$(CONFIG_CHARLCD)		+= charlcd.o
 obj-$(CONFIG_KS0108)		+= ks0108.o
 obj-$(CONFIG_CFAG12864B)	+= cfag12864b.o cfag12864bfb.o
 obj-$(CONFIG_IMG_ASCII_LCD)	+= img-ascii-lcd.o
+obj-$(CONFIG_HD44780)		+= hd44780.o
 obj-$(CONFIG_HT16K33)		+= ht16k33.o

drivers/auxdisplay/hd44780.c

+/*
+ * HD44780 Character LCD driver for Linux
+ *
+ * Copyright (C) 2000-2008, Willy Tarreau <w@1wt.eu>
+ * Copyright (C) 2016-2017 Glider bvba
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/slab.h>
+
+#include <misc/charlcd.h>
+
+
+enum hd44780_pin {
+	/* Order does matter due to writing to GPIO array subsets! */
+	PIN_DATA0,	/* Optional */
+	PIN_DATA1,	/* Optional */
+	PIN_DATA2,	/* Optional */
+	PIN_DATA3,	/* Optional */
+	PIN_DATA4,
+	PIN_DATA5,
+	PIN_DATA6,
+	PIN_DATA7,
+	PIN_CTRL_RS,
+	PIN_CTRL_RW,	/* Optional */
+	PIN_CTRL_E,
+	PIN_CTRL_BL,   /* Optional */
+	PIN_NUM
+};
+
+struct hd44780 {
+	struct gpio_desc *pins[PIN_NUM];
+};
+
+static void hd44780_backlight(struct charlcd *lcd, int on)
+{
+	struct hd44780 *hd = lcd->drvdata;
+
+	if (hd->pins[PIN_CTRL_BL])
+		gpiod_set_value_cansleep(hd->pins[PIN_CTRL_BL], on);
+}
+
+static void hd44780_strobe_gpio(struct hd44780 *hd)
+{
+	/* Maintain the data during 20 us before the strobe */
+	udelay(20);
+
+	gpiod_set_value_cansleep(hd->pins[PIN_CTRL_E], 1);
+
+	/* Maintain the strobe during 40 us */
+	udelay(40);
+
+	gpiod_set_value_cansleep(hd->pins[PIN_CTRL_E], 0);
+}
+
+/* write to an LCD panel register in 8 bit GPIO mode */
+static void hd44780_write_gpio8(struct hd44780 *hd, u8 val, unsigned int rs)
+{
+	int values[10];	/* for DATA[0-7], RS, RW */
+	unsigned int i, n;
+
+	for (i = 0; i < 8; i++)
+		values[PIN_DATA0 + i] = !!(val & BIT(i));
+	values[PIN_CTRL_RS] = rs;
+	n = 9;
+	if (hd->pins[PIN_CTRL_RW]) {
+		values[PIN_CTRL_RW] = 0;
+		n++;
+	}
+
+	/* Present the data to the port */
+	gpiod_set_array_value_cansleep(n, &hd->pins[PIN_DATA0], values);
+
+	hd44780_strobe_gpio(hd);
+}
+
+/* write to an LCD panel register in 4 bit GPIO mode */
+static void hd44780_write_gpio4(struct hd44780 *hd, u8 val, unsigned int rs)
+{
+	int values[10];	/* for DATA[0-7], RS, RW, but DATA[0-3] is unused */
+	unsigned int i, n;
+
+	/* High nibble + RS, RW */
+	for (i = 4; i < 8; i++)
+		values[PIN_DATA0 + i] = !!(val & BIT(i));
+	values[PIN_CTRL_RS] = rs;
+	n = 5;
+	if (hd->pins[PIN_CTRL_RW]) {
+		values[PIN_CTRL_RW] = 0;
+		n++;
+	}
+
+	/* Present the data to the port */
+	gpiod_set_array_value_cansleep(n, &hd->pins[PIN_DATA4],
+				       &values[PIN_DATA4]);
+
+	hd44780_strobe_gpio(hd);
+
+	/* Low nibble */
+	for (i = 0; i < 4; i++)
+		values[PIN_DATA4 + i] = !!(val & BIT(i));
+
+	/* Present the data to the port */
+	gpiod_set_array_value_cansleep(n, &hd->pins[PIN_DATA4],
+				       &values[PIN_DATA4]);
+
+	hd44780_strobe_gpio(hd);
+}
+
+/* Send a command to the LCD panel in 8 bit GPIO mode */
+static void hd44780_write_cmd_gpio8(struct charlcd *lcd, int cmd)
+{
+	struct hd44780 *hd = lcd->drvdata;
+
+	hd44780_write_gpio8(hd, cmd, 0);
+
+	/* The shortest command takes at least 120 us */
+	udelay(120);
+}
+
+/* Send data to the LCD panel in 8 bit GPIO mode */
+static void hd44780_write_data_gpio8(struct charlcd *lcd, int data)
+{
+	struct hd44780 *hd = lcd->drvdata;
+
+	hd44780_write_gpio8(hd, data, 1);
+
+	/* The shortest data takes at least 45 us */
+	udelay(45);
+}
+
+static const struct charlcd_ops hd44780_ops_gpio8 = {
+	.write_cmd	= hd44780_write_cmd_gpio8,
+	.write_data	= hd44780_write_data_gpio8,
+	.backlight	= hd44780_backlight,
+};
+
+/* Send a command to the LCD panel in 4 bit GPIO mode */
+static void hd44780_write_cmd_gpio4(struct charlcd *lcd, int cmd)
+{
+	struct hd44780 *hd = lcd->drvdata;
+
+	hd44780_write_gpio4(hd, cmd, 0);
+
+	/* The shortest command takes at least 120 us */
+	udelay(120);
+}
+
+/* Send 4-bits of a command to the LCD panel in raw 4 bit GPIO mode */
+static void hd44780_write_cmd_raw_gpio4(struct charlcd *lcd, int cmd)
+{
+	int values[10];	/* for DATA[0-7], RS, RW, but DATA[0-3] is unused */
+	struct hd44780 *hd = lcd->drvdata;
+	unsigned int i, n;
+
+	/* Command nibble + RS, RW */
+	for (i = 0; i < 4; i++)
+		values[PIN_DATA4 + i] = !!(cmd & BIT(i));
+	values[PIN_CTRL_RS] = 0;
+	n = 5;
+	if (hd->pins[PIN_CTRL_RW]) {
+		values[PIN_CTRL_RW] = 0;
+		n++;
+	}
+
+	/* Present the data to the port */
+	gpiod_set_array_value_cansleep(n, &hd->pins[PIN_DATA4],
+				       &values[PIN_DATA4]);
+
+	hd44780_strobe_gpio(hd);
+}
+
+/* Send data to the LCD panel in 4 bit GPIO mode */
+static void hd44780_write_data_gpio4(struct charlcd *lcd, int data)
+{
+	struct hd44780 *hd = lcd->drvdata;
+
+	hd44780_write_gpio4(hd, data, 1);
+
+	/* The shortest data takes at least 45 us */
+	udelay(45);
+}
+
+static const struct charlcd_ops hd44780_ops_gpio4 = {
+	.write_cmd	= hd44780_write_cmd_gpio4,
+	.write_cmd_raw4	= hd44780_write_cmd_raw_gpio4,
+	.write_data	= hd44780_write_data_gpio4,
+	.backlight	= hd44780_backlight,
+};
+
+static int hd44780_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	unsigned int i, base;
+	struct charlcd *lcd;
+	struct hd44780 *hd;
+	int ifwidth, ret;
+
+	/* Required pins */
+	ifwidth = gpiod_count(dev, "data");
+	if (ifwidth < 0)
+		return ifwidth;
+
+	switch (ifwidth) {
+	case 4:
+		base = PIN_DATA4;
+		break;
+	case 8:
+		base = PIN_DATA0;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	lcd = charlcd_alloc(sizeof(struct hd44780));
+	if (!lcd)
+		return -ENOMEM;
+
+	hd = lcd->drvdata;
+
+	for (i = 0; i < ifwidth; i++) {
+		hd->pins[base + i] = devm_gpiod_get_index(dev, "data", i,
+							  GPIOD_OUT_LOW);
+		if (IS_ERR(hd->pins[base + i])) {
+			ret = PTR_ERR(hd->pins[base + i]);
+			goto fail;
+		}
+	}
+
+	hd->pins[PIN_CTRL_E] = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW);
+	if (IS_ERR(hd->pins[PIN_CTRL_E])) {
+		ret = PTR_ERR(hd->pins[PIN_CTRL_E]);
+		goto fail;
+	}
+
+	hd->pins[PIN_CTRL_RS] = devm_gpiod_get(dev, "rs", GPIOD_OUT_HIGH);
+	if (IS_ERR(hd->pins[PIN_CTRL_RS])) {
+		ret = PTR_ERR(hd->pins[PIN_CTRL_RS]);
+		goto fail;
+	}
+
+	/* Optional pins */
+	hd->pins[PIN_CTRL_RW] = devm_gpiod_get_optional(dev, "rw",
+							GPIOD_OUT_LOW);
+	if (IS_ERR(hd->pins[PIN_CTRL_RW])) {
+		ret = PTR_ERR(hd->pins[PIN_CTRL_RW]);
+		goto fail;
+	}
+
+	hd->pins[PIN_CTRL_BL] = devm_gpiod_get_optional(dev, "backlight",
+							GPIOD_OUT_LOW);
+	if (IS_ERR(hd->pins[PIN_CTRL_BL])) {
+		ret = PTR_ERR(hd->pins[PIN_CTRL_BL]);
+		goto fail;
+	}
+
+	/* Required properties */
+	ret = device_property_read_u32(dev, "display-height", &lcd->height);
+	if (ret)
+		goto fail;
+	ret = device_property_read_u32(dev, "display-width", &lcd->width);
+	if (ret)
+		goto fail;
+
+	/*
+	 * On displays with more than two rows, the internal buffer width is
+	 * usually equal to the display width
+	 */
+	if (lcd->height > 2)
+		lcd->bwidth = lcd->width;
+
+	/* Optional properties */
+	device_property_read_u32(dev, "internal-buffer-width", &lcd->bwidth);
+
+	lcd->ifwidth = ifwidth;
+	lcd->ops = ifwidth == 8 ? &hd44780_ops_gpio8 : &hd44780_ops_gpio4;
+
+	ret = charlcd_register(lcd);
+	if (ret)
+		goto fail;
+
+	platform_set_drvdata(pdev, lcd);
+	return 0;
+
+fail:
+	kfree(lcd);
+	return ret;
+}
+
+static int hd44780_remove(struct platform_device *pdev)
+{
+	struct charlcd *lcd = platform_get_drvdata(pdev);
+
+	charlcd_unregister(lcd);
+	return 0;
+}
+
+static const struct of_device_id hd44780_of_match[] = {
+	{ .compatible = "hit,hd44780" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, hd44780_of_match);
+
+static struct platform_driver hd44780_driver = {
+	.probe = hd44780_probe,
+	.remove = hd44780_remove,
+	.driver		= {
+		.name	= "hd44780",
+		.of_match_table = hd44780_of_match,
+	},
+};
+
+module_platform_driver(hd44780_driver);
+MODULE_DESCRIPTION("HD44780 Character LCD driver");
+MODULE_AUTHOR("Geert Uytterhoeven <geert@linux-m68k.org>");
+MODULE_LICENSE("GPL");

drivers/block/Kconfig

@@ -339,6 +339,7 @@ config BLK_DEV_SX8
 
 config BLK_DEV_RAM
 	tristate "RAM block device support"
+	select DAX if BLK_DEV_RAM_DAX
 	---help---
 	  Saying Y here will allow you to use a portion of your RAM memory as
 	  a block device, so that you can make file systems on it, read and

drivers/block/brd.c

@@ -21,6 +21,7 @@
 #include <linux/slab.h>
 #ifdef CONFIG_BLK_DEV_RAM_DAX
 #include <linux/pfn_t.h>
+#include <linux/dax.h>
 #endif
 
 #include <linux/uaccess.h>
@@ -41,6 +42,9 @@ struct brd_device {
 
 	struct request_queue	*brd_queue;
 	struct gendisk		*brd_disk;
+#ifdef CONFIG_BLK_DEV_RAM_DAX
+	struct dax_device	*dax_dev;
+#endif
 	struct list_head	brd_list;
 
 	/*
@@ -375,30 +379,38 @@ static int brd_rw_page(struct block_device *bdev, sector_t sector,
 }
 
 #ifdef CONFIG_BLK_DEV_RAM_DAX
-static long brd_direct_access(struct block_device *bdev, sector_t sector,
-			void **kaddr, pfn_t *pfn, long size)
+static long __brd_direct_access(struct brd_device *brd, pgoff_t pgoff,
+		long nr_pages, void **kaddr, pfn_t *pfn)
 {
-	struct brd_device *brd = bdev->bd_disk->private_data;
 	struct page *page;
 
 	if (!brd)
 		return -ENODEV;
-	page = brd_insert_page(brd, sector);
+	page = brd_insert_page(brd, PFN_PHYS(pgoff) / 512);
 	if (!page)
 		return -ENOSPC;
 	*kaddr = page_address(page);
 	*pfn = page_to_pfn_t(page);
 
-	return PAGE_SIZE;
+	return 1;
 }
-#else
-#define brd_direct_access NULL
+
+static long brd_dax_direct_access(struct dax_device *dax_dev,
+		pgoff_t pgoff, long nr_pages, void **kaddr, pfn_t *pfn)
+{
+	struct brd_device *brd = dax_get_private(dax_dev);
+
+	return __brd_direct_access(brd, pgoff, nr_pages, kaddr, pfn);
+}
+
+static const struct dax_operations brd_dax_ops = {
+	.direct_access = brd_dax_direct_access,
+};
 #endif
 
 static const struct block_device_operations brd_fops = {
 	.owner =		THIS_MODULE,
 	.rw_page =		brd_rw_page,
-	.direct_access =	brd_direct_access,
 };
 
 /*
@@ -469,9 +481,6 @@ static struct brd_device *brd_alloc(int i)
 	blk_queue_max_discard_sectors(brd->brd_queue, UINT_MAX);
 	brd->brd_queue->limits.discard_zeroes_data = 1;
 	queue_flag_set_unlocked(QUEUE_FLAG_DISCARD, brd->brd_queue);
-#ifdef CONFIG_BLK_DEV_RAM_DAX
-	queue_flag_set_unlocked(QUEUE_FLAG_DAX, brd->brd_queue);
-#endif
 	disk = brd->brd_disk = alloc_disk(max_part);
 	if (!disk)
 		goto out_free_queue;
@@ -484,8 +493,21 @@ static struct brd_device *brd_alloc(int i)
 	sprintf(disk->disk_name, "ram%d", i);
 	set_capacity(disk, rd_size * 2);
 
+#ifdef CONFIG_BLK_DEV_RAM_DAX
+	queue_flag_set_unlocked(QUEUE_FLAG_DAX, brd->brd_queue);
+	brd->dax_dev = alloc_dax(brd, disk->disk_name, &brd_dax_ops);
+	if (!brd->dax_dev)
+		goto out_free_inode;
+#endif
+
+
 	return brd;
 
+#ifdef CONFIG_BLK_DEV_RAM_DAX
+out_free_inode:
+	kill_dax(brd->dax_dev);
+	put_dax(brd->dax_dev);
+#endif
 out_free_queue:
 	blk_cleanup_queue(brd->brd_queue);
 out_free_dev:
@@ -525,6 +547,10 @@ static struct brd_device *brd_init_one(int i, bool *new)
 static void brd_del_one(struct brd_device *brd)
 {
 	list_del(&brd->brd_list);
+#ifdef CONFIG_BLK_DEV_RAM_DAX
+	kill_dax(brd->dax_dev);
+	put_dax(brd->dax_dev);
+#endif
 	del_gendisk(brd->brd_disk);
 	brd_free(brd);
 }

drivers/char/hpet.c

@@ -575,7 +575,7 @@ static inline unsigned long hpet_time_div(struct hpets *hpets,
 }
 
 static int
-hpet_ioctl_common(struct hpet_dev *devp, int cmd, unsigned long arg,
+hpet_ioctl_common(struct hpet_dev *devp, unsigned int cmd, unsigned long arg,
 		  struct hpet_info *info)
 {
 	struct hpet_timer __iomem *timer;

drivers/char/virtio_console.c

@@ -2302,7 +2302,7 @@ static int __init init(void)
 
 	pdrvdata.debugfs_dir = debugfs_create_dir("virtio-ports", NULL);
 	if (!pdrvdata.debugfs_dir)
-		pr_warning("Error creating debugfs dir for virtio-ports\n");
+		pr_warn("Error creating debugfs dir for virtio-ports\n");
 	INIT_LIST_HEAD(&pdrvdata.consoles);
 	INIT_LIST_HEAD(&pdrvdata.portdevs);
 

drivers/dax/Kconfig

-menuconfig DEV_DAX
+menuconfig DAX
 	tristate "DAX: direct access to differentiated memory"
+	select SRCU
 	default m if NVDIMM_DAX
+
+if DAX
+
+config DEV_DAX
+	tristate "Device DAX: direct access mapping device"
 	depends on TRANSPARENT_HUGEPAGE
-	select SRCU
 	help
 	  Support raw access to differentiated (persistence, bandwidth,
 	  latency...) memory via an mmap(2) capable character
@@ -11,7 +16,6 @@ menuconfig DEV_DAX
 	  baseline memory pool.  Mappings of a /dev/daxX.Y device impose
 	  restrictions that make the mapping behavior deterministic.
 
-if DEV_DAX
 
 config DEV_DAX_PMEM
 	tristate "PMEM DAX: direct access to persistent memory"

drivers/dax/Makefile

-obj-$(CONFIG_DEV_DAX) += dax.o
+obj-$(CONFIG_DAX) += dax.o
+obj-$(CONFIG_DEV_DAX) += device_dax.o
 obj-$(CONFIG_DEV_DAX_PMEM) += dax_pmem.o
 
+dax-y := super.o
 dax_pmem-y := pmem.o
+device_dax-y := device.o

drivers/dax/dax-private.h

@@ -38,22 +38,18 @@ struct dax_region {
 };
 
 /**
- * struct dax_dev - subdivision of a dax region
+ * struct dev_dax - instance data for a subdivision of a dax region
  * @region - parent region
- * @inode - inode
- * @dev - device backing the character device
- * @cdev - core chardev data
- * @alive - !alive + srcu grace period == no new mappings can be established
+ * @dax_dev - core dax functionality
+ * @dev - device core
  * @id - child id in the region
  * @num_resources - number of physical address extents in this device
  * @res - array of physical address ranges
  */
-struct dax_dev {
+struct dev_dax {
 	struct dax_region *region;
-	struct inode *inode;
+	struct dax_device *dax_dev;
 	struct device dev;
-	struct cdev cdev;
-	bool alive;
 	int id;
 	int num_resources;
 	struct resource res[0];

drivers/dax/dax.h

 /*
- * Copyright(c) 2016 Intel Corporation. All rights reserved.
+ * Copyright(c) 2016 - 2017 Intel Corporation. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of version 2 of the GNU General Public License as
@@ -12,14 +12,7 @@
  */
 #ifndef __DAX_H__
 #define __DAX_H__
-struct device;
-struct dax_dev;
-struct resource;
-struct dax_region;
-void dax_region_put(struct dax_region *dax_region);
-struct dax_region *alloc_dax_region(struct device *parent,
-		int region_id, struct resource *res, unsigned int align,
-		void *addr, unsigned long flags);
-struct dax_dev *devm_create_dax_dev(struct dax_region *dax_region,
-		struct resource *res, int count);
+struct dax_device;
+struct dax_device *inode_dax(struct inode *inode);
+struct inode *dax_inode(struct dax_device *dax_dev);
 #endif /* __DAX_H__ */

drivers/dax/device-dax.h

+/*
+ * Copyright(c) 2016 Intel Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ */
+#ifndef __DEVICE_DAX_H__
+#define __DEVICE_DAX_H__
+struct device;
+struct dev_dax;
+struct resource;
+struct dax_region;
+void dax_region_put(struct dax_region *dax_region);
+struct dax_region *alloc_dax_region(struct device *parent,
+		int region_id, struct resource *res, unsigned int align,
+		void *addr, unsigned long flags);
+struct dev_dax *devm_create_dev_dax(struct dax_region *dax_region,
+		struct resource *res, int count);
+#endif /* __DEVICE_DAX_H__ */

drivers/dax/pmem.c

@@ -16,7 +16,7 @@
 #include <linux/pfn_t.h>
 #include "../nvdimm/pfn.h"
 #include "../nvdimm/nd.h"
-#include "dax.h"
+#include "device-dax.h"
 
 struct dax_pmem {
 	struct device *dev;
@@ -61,8 +61,8 @@ static int dax_pmem_probe(struct device *dev)
 	int rc;
 	void *addr;
 	struct resource res;
-	struct dax_dev *dax_dev;
 	struct nd_pfn_sb *pfn_sb;
+	struct dev_dax *dev_dax;
 	struct dax_pmem *dax_pmem;
 	struct nd_region *nd_region;
 	struct nd_namespace_io *nsio;
@@ -130,12 +130,12 @@ static int dax_pmem_probe(struct device *dev)
 		return -ENOMEM;
 
 	/* TODO: support for subdividing a dax region... */
-	dax_dev = devm_create_dax_dev(dax_region, &res, 1);
+	dev_dax = devm_create_dev_dax(dax_region, &res, 1);
 
-	/* child dax_dev instances now own the lifetime of the dax_region */
+	/* child dev_dax instances now own the lifetime of the dax_region */
 	dax_region_put(dax_region);
 
-	return PTR_ERR_OR_ZERO(dax_dev);
+	return PTR_ERR_OR_ZERO(dev_dax);
 }
 
 static struct nd_device_driver dax_pmem_driver = {

drivers/fpga/Kconfig

@@ -20,6 +20,12 @@ config FPGA_REGION
 	  FPGA Regions allow loading FPGA images under control of
 	  the Device Tree.
 
+config FPGA_MGR_ICE40_SPI
+	tristate "Lattice iCE40 SPI"
+	depends on OF && SPI
+	help
+	  FPGA manager driver support for Lattice iCE40 FPGAs over SPI.
+
 config FPGA_MGR_SOCFPGA
 	tristate "Altera SOCFPGA FPGA Manager"
 	depends on ARCH_SOCFPGA || COMPILE_TEST
@@ -33,6 +39,13 @@ config FPGA_MGR_SOCFPGA_A10
 	help
 	  FPGA manager driver support for Altera Arria10 SoCFPGA.
 
+config FPGA_MGR_TS73XX
+	tristate "Technologic Systems TS-73xx SBC FPGA Manager"
+	depends on ARCH_EP93XX && MACH_TS72XX
+	help
+	  FPGA manager driver support for the Altera Cyclone II FPGA
+	  present on the TS-73xx SBC boards.
+
 config FPGA_MGR_ZYNQ_FPGA
 	tristate "Xilinx Zynq FPGA"
 	depends on ARCH_ZYNQ || COMPILE_TEST

drivers/fpga/Makefile

@@ -6,8 +6,10 @@
 obj-$(CONFIG_FPGA)			+= fpga-mgr.o
 
 # FPGA Manager Drivers
+obj-$(CONFIG_FPGA_MGR_ICE40_SPI)	+= ice40-spi.o
 obj-$(CONFIG_FPGA_MGR_SOCFPGA)		+= socfpga.o
 obj-$(CONFIG_FPGA_MGR_SOCFPGA_A10)	+= socfpga-a10.o
+obj-$(CONFIG_FPGA_MGR_TS73XX)		+= ts73xx-fpga.o
 obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA)	+= zynq-fpga.o
 
 # FPGA Bridge Drivers

drivers/fpga/fpga-bridge.c

@@ -27,7 +27,7 @@ static DEFINE_IDA(fpga_bridge_ida);
 static struct class *fpga_bridge_class;
 
 /* Lock for adding/removing bridges to linked lists*/
-spinlock_t bridge_list_lock;
+static spinlock_t bridge_list_lock;
 
 static int fpga_bridge_of_node_match(struct device *dev, const void *data)
 {
@@ -146,11 +146,9 @@ EXPORT_SYMBOL_GPL(fpga_bridge_put);
 int fpga_bridges_enable(struct list_head *bridge_list)
 {
 	struct fpga_bridge *bridge;
-	struct list_head *node;
 	int ret;
 
-	list_for_each(node, bridge_list) {
-		bridge = list_entry(node, struct fpga_bridge, node);
+	list_for_each_entry(bridge, bridge_list, node) {
 		ret = fpga_bridge_enable(bridge);
 		if (ret)
 			return ret;
@@ -172,11 +170,9 @@ EXPORT_SYMBOL_GPL(fpga_bridges_enable);
 int fpga_bridges_disable(struct list_head *bridge_list)
 {
 	struct fpga_bridge *bridge;
-	struct list_head *node;
 	int ret;
 
-	list_for_each(node, bridge_list) {
-		bridge = list_entry(node, struct fpga_bridge, node);
+	list_for_each_entry(bridge, bridge_list, node) {
 		ret = fpga_bridge_disable(bridge);
 		if (ret)
 			return ret;
@@ -196,13 +192,10 @@ EXPORT_SYMBOL_GPL(fpga_bridges_disable);
  */
 void fpga_bridges_put(struct list_head *bridge_list)
 {
-	struct fpga_bridge *bridge;
-	struct list_head *node, *next;
+	struct fpga_bridge *bridge, *next;
 	unsigned long flags;
 
-	list_for_each_safe(node, next, bridge_list) {
-		bridge = list_entry(node, struct fpga_bridge, node);
-
+	list_for_each_entry_safe(bridge, next, bridge_list, node) {
 		fpga_bridge_put(bridge);
 
 		spin_lock_irqsave(&bridge_list_lock, flags);

drivers/fpga/fpga-mgr.c

@@ -361,7 +361,7 @@ static struct attribute *fpga_mgr_attrs[] = {
 };
 ATTRIBUTE_GROUPS(fpga_mgr);
 
-struct fpga_manager *__fpga_mgr_get(struct device *dev)
+static struct fpga_manager *__fpga_mgr_get(struct device *dev)
 {
 	struct fpga_manager *mgr;
 	int ret = -ENODEV;

drivers/fpga/fpga-region.c

@@ -337,8 +337,9 @@ static int child_regions_with_firmware(struct device_node *overlay)
  * The overlay must add either firmware-name or external-fpga-config property
  * to the FPGA Region.
  *
- *   firmware-name        : program the FPGA
- *   external-fpga-config : FPGA is already programmed
+ *   firmware-name         : program the FPGA
+ *   external-fpga-config  : FPGA is already programmed
+ *   encrypted-fpga-config : FPGA bitstream is encrypted
  *
  * The overlay can add other FPGA regions, but child FPGA regions cannot have a
  * firmware-name property since those regions don't exist yet.
@@ -373,6 +374,9 @@ static int fpga_region_notify_pre_apply(struct fpga_region *region,
 	if (of_property_read_bool(nd->overlay, "external-fpga-config"))
 		info->flags |= FPGA_MGR_EXTERNAL_CONFIG;
 
+	if (of_property_read_bool(nd->overlay, "encrypted-fpga-config"))
+		info->flags |= FPGA_MGR_ENCRYPTED_BITSTREAM;
+
 	of_property_read_string(nd->overlay, "firmware-name", &firmware_name);
 
 	of_property_read_u32(nd->overlay, "region-unfreeze-timeout-us",

drivers/fpga/ice40-spi.c

+/*
+ * FPGA Manager Driver for Lattice iCE40.
+ *
+ *  Copyright (c) 2016 Joel Holdsworth
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This driver adds support to the FPGA manager for configuring the SRAM of
+ * Lattice iCE40 FPGAs through slave SPI.
+ */
+
+#include <linux/fpga/fpga-mgr.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/spi/spi.h>
+#include <linux/stringify.h>
+
+#define ICE40_SPI_MAX_SPEED 25000000 /* Hz */
+#define ICE40_SPI_MIN_SPEED 1000000 /* Hz */
+
+#define ICE40_SPI_RESET_DELAY 1 /* us (>200ns) */
+#define ICE40_SPI_HOUSEKEEPING_DELAY 1200 /* us */
+
+#define ICE40_SPI_NUM_ACTIVATION_BYTES DIV_ROUND_UP(49, 8)
+
+struct ice40_fpga_priv {
+	struct spi_device *dev;
+	struct gpio_desc *reset;
+	struct gpio_desc *cdone;
+};
+
+static enum fpga_mgr_states ice40_fpga_ops_state(struct fpga_manager *mgr)
+{
+	struct ice40_fpga_priv *priv = mgr->priv;
+
+	return gpiod_get_value(priv->cdone) ? FPGA_MGR_STATE_OPERATING :
+		FPGA_MGR_STATE_UNKNOWN;
+}
+
+static int ice40_fpga_ops_write_init(struct fpga_manager *mgr,
+				     struct fpga_image_info *info,
+				     const char *buf, size_t count)
+{
+	struct ice40_fpga_priv *priv = mgr->priv;
+	struct spi_device *dev = priv->dev;
+	struct spi_message message;
+	struct spi_transfer assert_cs_then_reset_delay = {
+		.cs_change   = 1,
+		.delay_usecs = ICE40_SPI_RESET_DELAY
+	};
+	struct spi_transfer housekeeping_delay_then_release_cs = {
+		.delay_usecs = ICE40_SPI_HOUSEKEEPING_DELAY
+	};
+	int ret;
+
+	if ((info->flags & FPGA_MGR_PARTIAL_RECONFIG)) {
+		dev_err(&dev->dev,
+			"Partial reconfiguration is not supported\n");
+		return -ENOTSUPP;
+	}
+
+	/* Lock the bus, assert CRESET_B and SS_B and delay >200ns */
+	spi_bus_lock(dev->master);
+
+	gpiod_set_value(priv->reset, 1);
+
+	spi_message_init(&message);
+	spi_message_add_tail(&assert_cs_then_reset_delay, &message);
+	ret = spi_sync_locked(dev, &message);
+
+	/* Come out of reset */
+	gpiod_set_value(priv->reset, 0);
+
+	/* Abort if the chip-select failed */
+	if (ret)
+		goto fail;
+
+	/* Check CDONE is de-asserted i.e. the FPGA is reset */
+	if (gpiod_get_value(priv->cdone)) {
+		dev_err(&dev->dev, "Device reset failed, CDONE is asserted\n");
+		ret = -EIO;
+		goto fail;
+	}
+
+	/* Wait for the housekeeping to complete, and release SS_B */
+	spi_message_init(&message);
+	spi_message_add_tail(&housekeeping_delay_then_release_cs, &message);
+	ret = spi_sync_locked(dev, &message);
+
+fail:
+	spi_bus_unlock(dev->master);
+
+	return ret;
+}
+
+static int ice40_fpga_ops_write(struct fpga_manager *mgr,
+				const char *buf, size_t count)
+{
+	struct ice40_fpga_priv *priv = mgr->priv;
+
+	return spi_write(priv->dev, buf, count);
+}
+
+static int ice40_fpga_ops_write_complete(struct fpga_manager *mgr,
+					 struct fpga_image_info *info)
+{
+	struct ice40_fpga_priv *priv = mgr->priv;
+	struct spi_device *dev = priv->dev;
+	const u8 padding[ICE40_SPI_NUM_ACTIVATION_BYTES] = {0};
+
+	/* Check CDONE is asserted */
+	if (!gpiod_get_value(priv->cdone)) {
+		dev_err(&dev->dev,
+			"CDONE was not asserted after firmware transfer\n");
+		return -EIO;
+	}
+
+	/* Send of zero-padding to activate the firmware */
+	return spi_write(dev, padding, sizeof(padding));
+}
+
+static const struct fpga_manager_ops ice40_fpga_ops = {
+	.state = ice40_fpga_ops_state,
+	.write_init = ice40_fpga_ops_write_init,
+	.write = ice40_fpga_ops_write,
+	.write_complete = ice40_fpga_ops_write_complete,
+};
+
+static int ice40_fpga_probe(struct spi_device *spi)
+{
+	struct device *dev = &spi->dev;
+	struct ice40_fpga_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(&spi->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = spi;
+
+	/* Check board setup data. */
+	if (spi->max_speed_hz > ICE40_SPI_MAX_SPEED) {
+		dev_err(dev, "SPI speed is too high, maximum speed is "
+			__stringify(ICE40_SPI_MAX_SPEED) "\n");
+		return -EINVAL;
+	}
+
+	if (spi->max_speed_hz < ICE40_SPI_MIN_SPEED) {
+		dev_err(dev, "SPI speed is too low, minimum speed is "
+			__stringify(ICE40_SPI_MIN_SPEED) "\n");
+		return -EINVAL;
+	}
+
+	if (spi->mode & SPI_CPHA) {
+		dev_err(dev, "Bad SPI mode, CPHA not supported\n");
+		return -EINVAL;
+	}
+
+	/* Set up the GPIOs */
+	priv->cdone = devm_gpiod_get(dev, "cdone", GPIOD_IN);
+	if (IS_ERR(priv->cdone)) {
+		ret = PTR_ERR(priv->cdone);
+		dev_err(dev, "Failed to get CDONE GPIO: %d\n", ret);
+		return ret;
+	}
+
+	priv->reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(priv->reset)) {
+		ret = PTR_ERR(priv->reset);
+		dev_err(dev, "Failed to get CRESET_B GPIO: %d\n", ret);
+		return ret;
+	}
+
+	/* Register with the FPGA manager */
+	return fpga_mgr_register(dev, "Lattice iCE40 FPGA Manager",
+				 &ice40_fpga_ops, priv);
+}
+
+static int ice40_fpga_remove(struct spi_device *spi)
+{
+	fpga_mgr_unregister(&spi->dev);
+	return 0;
+}
+
+static const struct of_device_id ice40_fpga_of_match[] = {
+	{ .compatible = "lattice,ice40-fpga-mgr", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, ice40_fpga_of_match);
+
+static struct spi_driver ice40_fpga_driver = {
+	.probe = ice40_fpga_probe,
+	.remove = ice40_fpga_remove,
+	.driver = {
+		.name = "ice40spi",
+		.of_match_table = of_match_ptr(ice40_fpga_of_match),
+	},
+};
+
+module_spi_driver(ice40_fpga_driver);
+
+MODULE_AUTHOR("Joel Holdsworth <joel@airwebreathe.org.uk>");
+MODULE_DESCRIPTION("Lattice iCE40 FPGA Manager");
+MODULE_LICENSE("GPL v2");

drivers/fpga/ts73xx-fpga.c

+/*
+ * Technologic Systems TS-73xx SBC FPGA loader
+ *
+ * Copyright (C) 2016 Florian Fainelli <f.fainelli@gmail.com>
+ *
+ * FPGA Manager Driver for the on-board Altera Cyclone II FPGA found on
+ * TS-7300, heavily based on load_fpga.c in their vendor tree.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/string.h>
+#include <linux/iopoll.h>
+#include <linux/fpga/fpga-mgr.h>
+
+#define TS73XX_FPGA_DATA_REG		0
+#define TS73XX_FPGA_CONFIG_REG		1
+
+#define TS73XX_FPGA_WRITE_DONE		0x1
+#define TS73XX_FPGA_WRITE_DONE_TIMEOUT	1000	/* us */
+#define TS73XX_FPGA_RESET		0x2
+#define TS73XX_FPGA_RESET_LOW_DELAY	30	/* us */
+#define TS73XX_FPGA_RESET_HIGH_DELAY	80	/* us */
+#define TS73XX_FPGA_LOAD_OK		0x4
+#define TS73XX_FPGA_CONFIG_LOAD		0x8
+
+struct ts73xx_fpga_priv {
+	void __iomem	*io_base;
+	struct device	*dev;
+};
+
+static enum fpga_mgr_states ts73xx_fpga_state(struct fpga_manager *mgr)
+{
+	return FPGA_MGR_STATE_UNKNOWN;
+}
+
+static int ts73xx_fpga_write_init(struct fpga_manager *mgr,
+				  struct fpga_image_info *info,
+				  const char *buf, size_t count)
+{
+	struct ts73xx_fpga_priv *priv = mgr->priv;
+
+	/* Reset the FPGA */
+	writeb(0, priv->io_base + TS73XX_FPGA_CONFIG_REG);
+	udelay(TS73XX_FPGA_RESET_LOW_DELAY);
+	writeb(TS73XX_FPGA_RESET, priv->io_base + TS73XX_FPGA_CONFIG_REG);
+	udelay(TS73XX_FPGA_RESET_HIGH_DELAY);
+
+	return 0;
+}
+
+static int ts73xx_fpga_write(struct fpga_manager *mgr, const char *buf,
+			     size_t count)
+{
+	struct ts73xx_fpga_priv *priv = mgr->priv;
+	size_t i = 0;
+	int ret;
+	u8 reg;
+
+	while (count--) {
+		ret = readb_poll_timeout(priv->io_base + TS73XX_FPGA_CONFIG_REG,
+					 reg, !(reg & TS73XX_FPGA_WRITE_DONE),
+					 1, TS73XX_FPGA_WRITE_DONE_TIMEOUT);
+		if (ret < 0)
+			return ret;
+
+		writeb(buf[i], priv->io_base + TS73XX_FPGA_DATA_REG);
+		i++;
+	}
+
+	return 0;
+}
+
+static int ts73xx_fpga_write_complete(struct fpga_manager *mgr,
+				      struct fpga_image_info *info)
+{
+	struct ts73xx_fpga_priv *priv = mgr->priv;
+	u8 reg;
+
+	usleep_range(1000, 2000);
+	reg = readb(priv->io_base + TS73XX_FPGA_CONFIG_REG);
+	reg |= TS73XX_FPGA_CONFIG_LOAD;
+	writeb(reg, priv->io_base + TS73XX_FPGA_CONFIG_REG);
+
+	usleep_range(1000, 2000);
+	reg = readb(priv->io_base + TS73XX_FPGA_CONFIG_REG);
+	reg &= ~TS73XX_FPGA_CONFIG_LOAD;
+	writeb(reg, priv->io_base + TS73XX_FPGA_CONFIG_REG);
+
+	reg = readb(priv->io_base + TS73XX_FPGA_CONFIG_REG);
+	if ((reg & TS73XX_FPGA_LOAD_OK) != TS73XX_FPGA_LOAD_OK)
+		return -ETIMEDOUT;
+
+	return 0;
+}
+
+static const struct fpga_manager_ops ts73xx_fpga_ops = {
+	.state		= ts73xx_fpga_state,
+	.write_init	= ts73xx_fpga_write_init,
+	.write		= ts73xx_fpga_write,
+	.write_complete	= ts73xx_fpga_write_complete,
+};
+
+static int ts73xx_fpga_probe(struct platform_device *pdev)
+{
+	struct device *kdev = &pdev->dev;
+	struct ts73xx_fpga_priv *priv;
+	struct resource *res;
+
+	priv = devm_kzalloc(kdev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = kdev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->io_base = devm_ioremap_resource(kdev, res);
+	if (IS_ERR(priv->io_base)) {
+		dev_err(kdev, "unable to remap registers\n");
+		return PTR_ERR(priv->io_base);
+	}
+
+	return fpga_mgr_register(kdev, "TS-73xx FPGA Manager",
+				 &ts73xx_fpga_ops, priv);
+}
+
+static int ts73xx_fpga_remove(struct platform_device *pdev)
+{
+	fpga_mgr_unregister(&pdev->dev);
+
+	return 0;
+}
+
+static struct platform_driver ts73xx_fpga_driver = {
+	.driver	= {
+		.name	= "ts73xx-fpga-mgr",
+	},
+	.probe	= ts73xx_fpga_probe,
+	.remove	= ts73xx_fpga_remove,
+};
+module_platform_driver(ts73xx_fpga_driver);
+
+MODULE_AUTHOR("Florian Fainelli <f.fainelli@gmail.com>");
+MODULE_DESCRIPTION("TS-73xx FPGA Manager driver");
+MODULE_LICENSE("GPL v2");

drivers/fpga/zynq-fpga.c

@@ -72,6 +72,10 @@
 #define CTRL_PCAP_PR_MASK		BIT(27)
 /* Enable PCAP */
 #define CTRL_PCAP_MODE_MASK		BIT(26)
+/* Lower rate to allow decrypt on the fly */
+#define CTRL_PCAP_RATE_EN_MASK		BIT(25)
+/* System booted in secure mode */
+#define CTRL_SEC_EN_MASK		BIT(7)
 
 /* Miscellaneous Control Register bit definitions */
 /* Internal PCAP loopback */
@@ -266,6 +270,17 @@ static int zynq_fpga_ops_write_init(struct fpga_manager *mgr,
 	if (err)
 		return err;
 
+	/* check if bitstream is encrypted & and system's still secure */
+	if (info->flags & FPGA_MGR_ENCRYPTED_BITSTREAM) {
+		ctrl = zynq_fpga_read(priv, CTRL_OFFSET);
+		if (!(ctrl & CTRL_SEC_EN_MASK)) {
+			dev_err(&mgr->dev,
+				"System not secure, can't use crypted bitstreams\n");
+			err = -EINVAL;
+			goto out_err;
+		}
+	}
+
 	/* don't globally reset PL if we're doing partial reconfig */
 	if (!(info->flags & FPGA_MGR_PARTIAL_RECONFIG)) {
 		if (!zynq_fpga_has_sync(buf, count)) {
@@ -337,12 +352,19 @@ static int zynq_fpga_ops_write_init(struct fpga_manager *mgr,
 
 	/* set configuration register with following options:
 	 * - enable PCAP interface
-	 * - set throughput for maximum speed
+	 * - set throughput for maximum speed (if bistream not crypted)
 	 * - set CPU in user mode
 	 */
 	ctrl = zynq_fpga_read(priv, CTRL_OFFSET);
-	zynq_fpga_write(priv, CTRL_OFFSET,
-			(CTRL_PCAP_PR_MASK | CTRL_PCAP_MODE_MASK | ctrl));
+	if (info->flags & FPGA_MGR_ENCRYPTED_BITSTREAM)
+		zynq_fpga_write(priv, CTRL_OFFSET,
+				(CTRL_PCAP_PR_MASK | CTRL_PCAP_MODE_MASK
+				 | CTRL_PCAP_RATE_EN_MASK | ctrl));
+	else
+		zynq_fpga_write(priv, CTRL_OFFSET,
+				(CTRL_PCAP_PR_MASK | CTRL_PCAP_MODE_MASK
+				 | ctrl));
+
 
 	/* We expect that the command queue is empty right now. */
 	status = zynq_fpga_read(priv, STATUS_OFFSET);

drivers/hv/channel.c

@@ -333,7 +333,7 @@ static int create_gpadl_header(void *kbuffer, u32 size,
 			 * Gpadl is u32 and we are using a pointer which could
 			 * be 64-bit
 			 * This is governed by the guest/host protocol and
-			 * so the hypervisor gurantees that this is ok.
+			 * so the hypervisor guarantees that this is ok.
 			 */
 			for (i = 0; i < pfncurr; i++)
 				gpadl_body->pfn[i] = slow_virt_to_phys(
@@ -380,7 +380,7 @@ static int create_gpadl_header(void *kbuffer, u32 size,
 }
 
 /*
- * vmbus_establish_gpadl - Estabish a GPADL for the specified buffer
+ * vmbus_establish_gpadl - Establish a GPADL for the specified buffer
  *
  * @channel: a channel
  * @kbuffer: from kmalloc or vmalloc
@@ -731,7 +731,7 @@ int vmbus_sendpacket_pagebuffer_ctl(struct vmbus_channel *channel,
 	/* Setup the descriptor */
 	desc.type = VM_PKT_DATA_USING_GPA_DIRECT;
 	desc.flags = flags;
-	desc.dataoffset8 = descsize >> 3; /* in 8-bytes grandularity */
+	desc.dataoffset8 = descsize >> 3; /* in 8-bytes granularity */
 	desc.length8 = (u16)(packetlen_aligned >> 3);
 	desc.transactionid = requestid;
 	desc.rangecount = pagecount;
@@ -792,7 +792,7 @@ int vmbus_sendpacket_mpb_desc(struct vmbus_channel *channel,
 	/* Setup the descriptor */
 	desc->type = VM_PKT_DATA_USING_GPA_DIRECT;
 	desc->flags = VMBUS_DATA_PACKET_FLAG_COMPLETION_REQUESTED;
-	desc->dataoffset8 = desc_size >> 3; /* in 8-bytes grandularity */
+	desc->dataoffset8 = desc_size >> 3; /* in 8-bytes granularity */
 	desc->length8 = (u16)(packetlen_aligned >> 3);
 	desc->transactionid = requestid;
 	desc->rangecount = 1;
@@ -842,7 +842,7 @@ int vmbus_sendpacket_multipagebuffer(struct vmbus_channel *channel,
 	/* Setup the descriptor */
 	desc.type = VM_PKT_DATA_USING_GPA_DIRECT;
 	desc.flags = VMBUS_DATA_PACKET_FLAG_COMPLETION_REQUESTED;
-	desc.dataoffset8 = descsize >> 3; /* in 8-bytes grandularity */
+	desc.dataoffset8 = descsize >> 3; /* in 8-bytes granularity */
 	desc.length8 = (u16)(packetlen_aligned >> 3);
 	desc.transactionid = requestid;
 	desc.rangecount = 1;

drivers/hv/channel_mgmt.c

@@ -1080,30 +1080,30 @@ static void vmbus_onversion_response(
 }
 
 /* Channel message dispatch table */
-struct vmbus_channel_message_table_entry
-	channel_message_table[CHANNELMSG_COUNT] = {
-	{CHANNELMSG_INVALID,			0, NULL},
-	{CHANNELMSG_OFFERCHANNEL,		0, vmbus_onoffer},
-	{CHANNELMSG_RESCIND_CHANNELOFFER,	0, vmbus_onoffer_rescind},
-	{CHANNELMSG_REQUESTOFFERS,		0, NULL},
-	{CHANNELMSG_ALLOFFERS_DELIVERED,	1, vmbus_onoffers_delivered},
-	{CHANNELMSG_OPENCHANNEL,		0, NULL},
-	{CHANNELMSG_OPENCHANNEL_RESULT,		1, vmbus_onopen_result},
-	{CHANNELMSG_CLOSECHANNEL,		0, NULL},
-	{CHANNELMSG_GPADL_HEADER,		0, NULL},
-	{CHANNELMSG_GPADL_BODY,			0, NULL},
-	{CHANNELMSG_GPADL_CREATED,		1, vmbus_ongpadl_created},
-	{CHANNELMSG_GPADL_TEARDOWN,		0, NULL},
-	{CHANNELMSG_GPADL_TORNDOWN,		1, vmbus_ongpadl_torndown},
-	{CHANNELMSG_RELID_RELEASED,		0, NULL},
-	{CHANNELMSG_INITIATE_CONTACT,		0, NULL},
-	{CHANNELMSG_VERSION_RESPONSE,		1, vmbus_onversion_response},
-	{CHANNELMSG_UNLOAD,			0, NULL},
-	{CHANNELMSG_UNLOAD_RESPONSE,		1, vmbus_unload_response},
-	{CHANNELMSG_18,				0, NULL},
-	{CHANNELMSG_19,				0, NULL},
-	{CHANNELMSG_20,				0, NULL},
-	{CHANNELMSG_TL_CONNECT_REQUEST,		0, NULL},
+const struct vmbus_channel_message_table_entry
+channel_message_table[CHANNELMSG_COUNT] = {
+	{ CHANNELMSG_INVALID,			0, NULL },
+	{ CHANNELMSG_OFFERCHANNEL,		0, vmbus_onoffer },
+	{ CHANNELMSG_RESCIND_CHANNELOFFER,	0, vmbus_onoffer_rescind },
+	{ CHANNELMSG_REQUESTOFFERS,		0, NULL },
+	{ CHANNELMSG_ALLOFFERS_DELIVERED,	1, vmbus_onoffers_delivered },
+	{ CHANNELMSG_OPENCHANNEL,		0, NULL },
+	{ CHANNELMSG_OPENCHANNEL_RESULT,	1, vmbus_onopen_result },
+	{ CHANNELMSG_CLOSECHANNEL,		0, NULL },
+	{ CHANNELMSG_GPADL_HEADER,		0, NULL },
+	{ CHANNELMSG_GPADL_BODY,		0, NULL },
+	{ CHANNELMSG_GPADL_CREATED,		1, vmbus_ongpadl_created },
+	{ CHANNELMSG_GPADL_TEARDOWN,		0, NULL },
+	{ CHANNELMSG_GPADL_TORNDOWN,		1, vmbus_ongpadl_torndown },
+	{ CHANNELMSG_RELID_RELEASED,		0, NULL },
+	{ CHANNELMSG_INITIATE_CONTACT,		0, NULL },
+	{ CHANNELMSG_VERSION_RESPONSE,		1, vmbus_onversion_response },
+	{ CHANNELMSG_UNLOAD,			0, NULL },
+	{ CHANNELMSG_UNLOAD_RESPONSE,		1, vmbus_unload_response },
+	{ CHANNELMSG_18,			0, NULL },
+	{ CHANNELMSG_19,			0, NULL },
+	{ CHANNELMSG_20,			0, NULL },
+	{ CHANNELMSG_TL_CONNECT_REQUEST,	0, NULL },
 };
 
 /*

drivers/hv/connection.c

@@ -296,44 +296,47 @@ struct vmbus_channel *relid2channel(u32 relid)
 
 /*
  * vmbus_on_event - Process a channel event notification
+ *
+ * For batched channels (default) optimize host to guest signaling
+ * by ensuring:
+ * 1. While reading the channel, we disable interrupts from host.
+ * 2. Ensure that we process all posted messages from the host
+ *    before returning from this callback.
+ * 3. Once we return, enable signaling from the host. Once this
+ *    state is set we check to see if additional packets are
+ *    available to read. In this case we repeat the process.
+ *    If this tasklet has been running for a long time
+ *    then reschedule ourselves.
  */
 void vmbus_on_event(unsigned long data)
 {
 	struct vmbus_channel *channel = (void *) data;
-	void (*callback_fn)(void *);
+	unsigned long time_limit = jiffies + 2;
 
-	/*
-	 * A channel once created is persistent even when there
-	 * is no driver handling the device. An unloading driver
-	 * sets the onchannel_callback to NULL on the same CPU
-	 * as where this interrupt is handled (in an interrupt context).
-	 * Thus, checking and invoking the driver specific callback takes
-	 * care of orderly unloading of the driver.
-	 */
-	callback_fn = READ_ONCE(channel->onchannel_callback);
-	if (unlikely(callback_fn == NULL))
-		return;
-
-	(*callback_fn)(channel->channel_callback_context);
-
-	if (channel->callback_mode == HV_CALL_BATCHED) {
-		/*
-		 * This callback reads the messages sent by the host.
-		 * We can optimize host to guest signaling by ensuring:
-		 * 1. While reading the channel, we disable interrupts from
-		 *    host.
-		 * 2. Ensure that we process all posted messages from the host
-		 *    before returning from this callback.
-		 * 3. Once we return, enable signaling from the host. Once this
-		 *    state is set we check to see if additional packets are
-		 *    available to read. In this case we repeat the process.
+	do {
+		void (*callback_fn)(void *);
+
+		/* A channel once created is persistent even when
+		 * there is no driver handling the device. An
+		 * unloading driver sets the onchannel_callback to NULL.
 		 */
-		if (hv_end_read(&channel->inbound) != 0) {
-			hv_begin_read(&channel->inbound);
+		callback_fn = READ_ONCE(channel->onchannel_callback);
+		if (unlikely(callback_fn == NULL))
+			return;
 
-			tasklet_schedule(&channel->callback_event);
-		}
-	}
+		(*callback_fn)(channel->channel_callback_context);
+
+		if (channel->callback_mode != HV_CALL_BATCHED)
+			return;
+
+		if (likely(hv_end_read(&channel->inbound) == 0))
+			return;
+
+		hv_begin_read(&channel->inbound);
+	} while (likely(time_before(jiffies, time_limit)));
+
+	/* The time limit (2 jiffies) has been reached */
+	tasklet_schedule(&channel->callback_event);
 }
 
 /*

drivers/hv/hv.c

@@ -254,7 +254,10 @@ int hv_synic_init(unsigned int cpu)
 	shared_sint.as_uint64 = 0;
 	shared_sint.vector = HYPERVISOR_CALLBACK_VECTOR;
 	shared_sint.masked = false;
-	shared_sint.auto_eoi = true;
+	if (ms_hyperv.hints & HV_X64_DEPRECATING_AEOI_RECOMMENDED)
+		shared_sint.auto_eoi = false;
+	else
+		shared_sint.auto_eoi = true;
 
 	hv_set_synint_state(HV_X64_MSR_SINT0 + VMBUS_MESSAGE_SINT,
 			    shared_sint.as_uint64);

drivers/hv/hv_balloon.c

@@ -722,8 +722,6 @@ static void hv_mem_hot_add(unsigned long start, unsigned long size,
 						    5*HZ);
 		post_status(&dm_device);
 	}
-
-	return;
 }
 
 static void hv_online_page(struct page *pg)

drivers/hv/hv_fcopy.c

@@ -186,8 +186,6 @@ static void fcopy_send_data(struct work_struct *dummy)
 		}
 	}
 	kfree(smsg_out);
-
-	return;
 }
 
 /*

drivers/hv/hv_kvp.c

@@ -69,7 +69,7 @@ static const int fw_versions[] = {
  *
  * While the request/response protocol is guaranteed by the host, we further
  * ensure this by serializing packet processing in this driver - we do not
- * read additional packets from the VMBUs until the current packet is fully
+ * read additional packets from the VMBUS until the current packet is fully
  * handled.
  */
 
@@ -397,7 +397,7 @@ kvp_send_key(struct work_struct *dummy)
 	 * the max lengths specified. We will however, reserve room
 	 * for the string terminating character - in the utf16s_utf8s()
 	 * function we limit the size of the buffer where the converted
-	 * string is placed to HV_KVP_EXCHANGE_MAX_*_SIZE -1 to gaurantee
+	 * string is placed to HV_KVP_EXCHANGE_MAX_*_SIZE -1 to guarantee
 	 * that the strings can be properly terminated!
 	 */
 
@@ -483,8 +483,6 @@ kvp_send_key(struct work_struct *dummy)
 	}
 
 	kfree(message);
-
-	return;
 }
 
 /*
@@ -533,7 +531,7 @@ kvp_respond_to_host(struct hv_kvp_msg *msg_to_host, int error)
 	 */
 	if (error) {
 		/*
-		 * Something failed or we have timedout;
+		 * Something failed or we have timed out;
 		 * terminate the current host-side iteration.
 		 */
 		goto response_done;
@@ -607,8 +605,8 @@ kvp_respond_to_host(struct hv_kvp_msg *msg_to_host, int error)
  * This callback is invoked when we get a KVP message from the host.
  * The host ensures that only one KVP transaction can be active at a time.
  * KVP implementation in Linux needs to forward the key to a user-mde
- * component to retrive the corresponding value. Consequently, we cannot
- * respond to the host in the conext of this callback. Since the host
+ * component to retrieve the corresponding value. Consequently, we cannot
+ * respond to the host in the context of this callback. Since the host
  * guarantees that at most only one transaction can be active at a time,
  * we stash away the transaction state in a set of global variables.
  */

drivers/hv/hv_snapshot.c

@@ -212,8 +212,6 @@ static void vss_send_op(void)
 	}
 
 	kfree(vss_msg);
-
-	return;
 }
 
 static void vss_handle_request(struct work_struct *dummy)

drivers/hv/hyperv_vmbus.h

@@ -218,8 +218,8 @@ struct hv_per_cpu_context {
 
 struct hv_context {
 	/* We only support running on top of Hyper-V
-	* So at this point this really can only contain the Hyper-V ID
-	*/
+	 * So at this point this really can only contain the Hyper-V ID
+	 */
 	u64 guestid;
 
 	void *tsc_page;
@@ -248,14 +248,6 @@ struct hv_context {
 
 extern struct hv_context hv_context;
 
-struct hv_ring_buffer_debug_info {
-	u32 current_interrupt_mask;
-	u32 current_read_index;
-	u32 current_write_index;
-	u32 bytes_avail_toread;
-	u32 bytes_avail_towrite;
-};
-
 /* Hv Interface */
 
 extern int hv_init(void);
@@ -289,9 +281,6 @@ int hv_ringbuffer_read(struct vmbus_channel *channel,
 		       void *buffer, u32 buflen, u32 *buffer_actual_len,
 		       u64 *requestid, bool raw);
 
-void hv_ringbuffer_get_debuginfo(const struct hv_ring_buffer_info *ring_info,
-				 struct hv_ring_buffer_debug_info *debug_info);
-
 /*
  * Maximum channels is determined by the size of the interrupt page
  * which is PAGE_SIZE. 1/2 of PAGE_SIZE is for send endpoint interrupt
@@ -376,7 +365,7 @@ struct vmbus_channel_message_table_entry {
 	void (*message_handler)(struct vmbus_channel_message_header *msg);
 };
 
-extern struct vmbus_channel_message_table_entry
+extern const struct vmbus_channel_message_table_entry
 	channel_message_table[CHANNELMSG_COUNT];
 
 
@@ -403,17 +392,17 @@ int vmbus_post_msg(void *buffer, size_t buflen, bool can_sleep);
 void vmbus_on_event(unsigned long data);
 void vmbus_on_msg_dpc(unsigned long data);
 
-int hv_kvp_init(struct hv_util_service *);
+int hv_kvp_init(struct hv_util_service *srv);
 void hv_kvp_deinit(void);
-void hv_kvp_onchannelcallback(void *);
+void hv_kvp_onchannelcallback(void *context);
 
-int hv_vss_init(struct hv_util_service *);
+int hv_vss_init(struct hv_util_service *srv);
 void hv_vss_deinit(void);
-void hv_vss_onchannelcallback(void *);
+void hv_vss_onchannelcallback(void *context);
 
-int hv_fcopy_init(struct hv_util_service *);
+int hv_fcopy_init(struct hv_util_service *srv);
 void hv_fcopy_deinit(void);
-void hv_fcopy_onchannelcallback(void *);
+void hv_fcopy_onchannelcallback(void *context);
 void vmbus_initiate_unload(bool crash);
 
 static inline void hv_poll_channel(struct vmbus_channel *channel,

drivers/hv/ring_buffer.c

@@ -73,8 +73,6 @@ static void hv_signal_on_write(u32 old_write, struct vmbus_channel *channel)
 	 */
 	if (old_write == READ_ONCE(rbi->ring_buffer->read_index))
 		vmbus_setevent(channel);
-
-	return;
 }
 
 /* Get the next write location for the specified ring buffer. */
@@ -208,6 +206,7 @@ void hv_ringbuffer_get_debuginfo(const struct hv_ring_buffer_info *ring_info,
 			ring_info->ring_buffer->interrupt_mask;
 	}
 }
+EXPORT_SYMBOL_GPL(hv_ringbuffer_get_debuginfo);
 
 /* Initialize the ring buffer. */
 int hv_ringbuffer_init(struct hv_ring_buffer_info *ring_info,
@@ -267,14 +266,13 @@ void hv_ringbuffer_cleanup(struct hv_ring_buffer_info *ring_info)
 int hv_ringbuffer_write(struct vmbus_channel *channel,
 			const struct kvec *kv_list, u32 kv_count)
 {
-	int i = 0;
+	int i;
 	u32 bytes_avail_towrite;
-	u32 totalbytes_towrite = 0;
-
+	u32 totalbytes_towrite = sizeof(u64);
 	u32 next_write_location;
 	u32 old_write;
-	u64 prev_indices = 0;
-	unsigned long flags = 0;
+	u64 prev_indices;
+	unsigned long flags;
 	struct hv_ring_buffer_info *outring_info = &channel->outbound;
 
 	if (channel->rescind)
@@ -283,8 +281,6 @@ int hv_ringbuffer_write(struct vmbus_channel *channel,
 	for (i = 0; i < kv_count; i++)
 		totalbytes_towrite += kv_list[i].iov_len;
 
-	totalbytes_towrite += sizeof(u64);
-
 	spin_lock_irqsave(&outring_info->ring_lock, flags);
 
 	bytes_avail_towrite = hv_get_bytes_to_write(outring_info);
@@ -341,18 +337,16 @@ int hv_ringbuffer_read(struct vmbus_channel *channel,
 		       u64 *requestid, bool raw)
 {
 	u32 bytes_avail_toread;
-	u32 next_read_location = 0;
+	u32 next_read_location;
 	u64 prev_indices = 0;
 	struct vmpacket_descriptor desc;
 	u32 offset;
 	u32 packetlen;
-	int ret = 0;
 	struct hv_ring_buffer_info *inring_info = &channel->inbound;
 
 	if (buflen <= 0)
 		return -EINVAL;
 
-
 	*buffer_actual_len = 0;
 	*requestid = 0;
 
@@ -363,7 +357,7 @@ int hv_ringbuffer_read(struct vmbus_channel *channel,
 		 * No error is set when there is even no header, drivers are
 		 * supposed to analyze buffer_actual_len.
 		 */
-		return ret;
+		return 0;
 	}
 
 	init_cached_read_index(channel);
@@ -408,5 +402,5 @@ int hv_ringbuffer_read(struct vmbus_channel *channel,
 
 	hv_signal_on_read(channel);
 
-	return ret;
+	return 0;
 }

drivers/hv/vmbus_drv.c

@@ -787,8 +787,6 @@ static void vmbus_shutdown(struct device *child_device)
 
 	if (drv->shutdown)
 		drv->shutdown(dev);
-
-	return;
 }
 
 
@@ -855,7 +853,7 @@ void vmbus_on_msg_dpc(unsigned long data)
 	struct hv_message *msg = (struct hv_message *)page_addr +
 				  VMBUS_MESSAGE_SINT;
 	struct vmbus_channel_message_header *hdr;
-	struct vmbus_channel_message_table_entry *entry;
+	const struct vmbus_channel_message_table_entry *entry;
 	struct onmessage_work_context *ctx;
 	u32 message_type = msg->header.message_type;
 

drivers/md/Kconfig

@@ -200,6 +200,7 @@ config BLK_DEV_DM_BUILTIN
 config BLK_DEV_DM
 	tristate "Device mapper support"
 	select BLK_DEV_DM_BUILTIN
+	select DAX
 	---help---
 	  Device-mapper is a low level volume manager.  It works by allowing
 	  people to specify mappings for ranges of logical sectors.  Various

drivers/md/dm-core.h

@@ -58,6 +58,7 @@ struct mapped_device {
 	struct target_type *immutable_target_type;
 
 	struct gendisk *disk;
+	struct dax_device *dax_dev;
 	char name[16];
 
 	void *interface_ptr;

drivers/md/dm-linear.c

@@ -9,6 +9,7 @@
 #include <linux/init.h>
 #include <linux/blkdev.h>
 #include <linux/bio.h>
+#include <linux/dax.h>
 #include <linux/slab.h>
 #include <linux/device-mapper.h>
 
@@ -141,22 +142,20 @@ static int linear_iterate_devices(struct dm_target *ti,
 	return fn(ti, lc->dev, lc->start, ti->len, data);
 }
 
-static long linear_direct_access(struct dm_target *ti, sector_t sector,
-				 void **kaddr, pfn_t *pfn, long size)
+static long linear_dax_direct_access(struct dm_target *ti, pgoff_t pgoff,
+		long nr_pages, void **kaddr, pfn_t *pfn)
 {
+	long ret;
 	struct linear_c *lc = ti->private;
 	struct block_device *bdev = lc->dev->bdev;
-	struct blk_dax_ctl dax = {
-		.sector = linear_map_sector(ti, sector),
-		.size = size,
-	};
-	long ret;
-
-	ret = bdev_direct_access(bdev, &dax);
-	*kaddr = dax.addr;
-	*pfn = dax.pfn;
-
-	return ret;
+	struct dax_device *dax_dev = lc->dev->dax_dev;
+	sector_t dev_sector, sector = pgoff * PAGE_SECTORS;
+
+	dev_sector = linear_map_sector(ti, sector);
+	ret = bdev_dax_pgoff(bdev, dev_sector, nr_pages * PAGE_SIZE, &pgoff);
+	if (ret)
+		return ret;
+	return dax_direct_access(dax_dev, pgoff, nr_pages, kaddr, pfn);
 }
 
 static struct target_type linear_target = {
@@ -169,7 +168,7 @@ static struct target_type linear_target = {
 	.status = linear_status,
 	.prepare_ioctl = linear_prepare_ioctl,
 	.iterate_devices = linear_iterate_devices,
-	.direct_access = linear_direct_access,
+	.direct_access = linear_dax_direct_access,
 };
 
 int __init dm_linear_init(void)

drivers/md/dm-snap.c

@@ -2302,8 +2302,8 @@ static int origin_map(struct dm_target *ti, struct bio *bio)
 	return do_origin(o->dev, bio);
 }
 
-static long origin_direct_access(struct dm_target *ti, sector_t sector,
-		void **kaddr, pfn_t *pfn, long size)
+static long origin_dax_direct_access(struct dm_target *ti, pgoff_t pgoff,
+		long nr_pages, void **kaddr, pfn_t *pfn)
 {
 	DMWARN("device does not support dax.");
 	return -EIO;
@@ -2368,7 +2368,7 @@ static struct target_type origin_target = {
 	.postsuspend = origin_postsuspend,
 	.status  = origin_status,
 	.iterate_devices = origin_iterate_devices,
-	.direct_access = origin_direct_access,
+	.direct_access = origin_dax_direct_access,
 };
 
 static struct target_type snapshot_target = {

drivers/md/dm-stripe.c

@@ -11,6 +11,7 @@
 #include <linux/init.h>
 #include <linux/blkdev.h>
 #include <linux/bio.h>
+#include <linux/dax.h>
 #include <linux/slab.h>
 #include <linux/log2.h>
 
@@ -308,27 +309,25 @@ static int stripe_map(struct dm_target *ti, struct bio *bio)
 	return DM_MAPIO_REMAPPED;
 }
 
-static long stripe_direct_access(struct dm_target *ti, sector_t sector,
-				 void **kaddr, pfn_t *pfn, long size)
+static long stripe_dax_direct_access(struct dm_target *ti, pgoff_t pgoff,
+		long nr_pages, void **kaddr, pfn_t *pfn)
 {
+	sector_t dev_sector, sector = pgoff * PAGE_SECTORS;
 	struct stripe_c *sc = ti->private;
-	uint32_t stripe;
+	struct dax_device *dax_dev;
 	struct block_device *bdev;
-	struct blk_dax_ctl dax = {
-		.size = size,
-	};
+	uint32_t stripe;
 	long ret;
 
-	stripe_map_sector(sc, sector, &stripe, &dax.sector);
-
-	dax.sector += sc->stripe[stripe].physical_start;
+	stripe_map_sector(sc, sector, &stripe, &dev_sector);
+	dev_sector += sc->stripe[stripe].physical_start;
+	dax_dev = sc->stripe[stripe].dev->dax_dev;
 	bdev = sc->stripe[stripe].dev->bdev;
 
-	ret = bdev_direct_access(bdev, &dax);
-	*kaddr = dax.addr;
-	*pfn = dax.pfn;
-
-	return ret;
+	ret = bdev_dax_pgoff(bdev, dev_sector, nr_pages * PAGE_SIZE, &pgoff);
+	if (ret)
+		return ret;
+	return dax_direct_access(dax_dev, pgoff, nr_pages, kaddr, pfn);
 }
 
 /*
@@ -448,7 +447,7 @@ static struct target_type stripe_target = {
 	.status = stripe_status,
 	.iterate_devices = stripe_iterate_devices,
 	.io_hints = stripe_io_hints,
-	.direct_access = stripe_direct_access,
+	.direct_access = stripe_dax_direct_access,
 };
 
 int __init dm_stripe_init(void)

drivers/md/dm-target.c

@@ -142,8 +142,8 @@ static void io_err_release_clone_rq(struct request *clone)
 {
 }
 
-static long io_err_direct_access(struct dm_target *ti, sector_t sector,
-				 void **kaddr, pfn_t *pfn, long size)
+static long io_err_dax_direct_access(struct dm_target *ti, pgoff_t pgoff,
+		long nr_pages, void **kaddr, pfn_t *pfn)
 {
 	return -EIO;
 }
@@ -157,7 +157,7 @@ static struct target_type error_target = {
 	.map  = io_err_map,
 	.clone_and_map_rq = io_err_clone_and_map_rq,
 	.release_clone_rq = io_err_release_clone_rq,
-	.direct_access = io_err_direct_access,
+	.direct_access = io_err_dax_direct_access,
 };
 
 int __init dm_target_init(void)

drivers/md/dm.c

@@ -16,6 +16,7 @@
 #include <linux/blkpg.h>
 #include <linux/bio.h>
 #include <linux/mempool.h>
+#include <linux/dax.h>
 #include <linux/slab.h>
 #include <linux/idr.h>
 #include <linux/hdreg.h>
@@ -629,6 +630,7 @@ static int open_table_device(struct table_device *td, dev_t dev,
 	}
 
 	td->dm_dev.bdev = bdev;
+	td->dm_dev.dax_dev = dax_get_by_host(bdev->bd_disk->disk_name);
 	return 0;
 }
 
@@ -642,7 +644,9 @@ static void close_table_device(struct table_device *td, struct mapped_device *md
 
 	bd_unlink_disk_holder(td->dm_dev.bdev, dm_disk(md));
 	blkdev_put(td->dm_dev.bdev, td->dm_dev.mode | FMODE_EXCL);
+	put_dax(td->dm_dev.dax_dev);
 	td->dm_dev.bdev = NULL;
+	td->dm_dev.dax_dev = NULL;
 }
 
 static struct table_device *find_table_device(struct list_head *l, dev_t dev,
@@ -908,31 +912,49 @@ int dm_set_target_max_io_len(struct dm_target *ti, sector_t len)
 }
 EXPORT_SYMBOL_GPL(dm_set_target_max_io_len);
 
-static long dm_blk_direct_access(struct block_device *bdev, sector_t sector,
-				 void **kaddr, pfn_t *pfn, long size)
+static struct dm_target *dm_dax_get_live_target(struct mapped_device *md,
+		sector_t sector, int *srcu_idx)
 {
-	struct mapped_device *md = bdev->bd_disk->private_data;
 	struct dm_table *map;
 	struct dm_target *ti;
-	int srcu_idx;
-	long len, ret = -EIO;
 
-	map = dm_get_live_table(md, &srcu_idx);
+	map = dm_get_live_table(md, srcu_idx);
 	if (!map)
-		goto out;
+		return NULL;
 
 	ti = dm_table_find_target(map, sector);
 	if (!dm_target_is_valid(ti))
-		goto out;
+		return NULL;
+
+	return ti;
+}
+
+static long dm_dax_direct_access(struct dax_device *dax_dev, pgoff_t pgoff,
+		long nr_pages, void **kaddr, pfn_t *pfn)
+{
+	struct mapped_device *md = dax_get_private(dax_dev);
+	sector_t sector = pgoff * PAGE_SECTORS;
+	struct dm_target *ti;
+	long len, ret = -EIO;
+	int srcu_idx;
 
-	len = max_io_len(sector, ti) << SECTOR_SHIFT;
-	size = min(len, size);
+	ti = dm_dax_get_live_target(md, sector, &srcu_idx);
 
+	if (!ti)
+		goto out;
+	if (!ti->type->direct_access)
+		goto out;
+	len = max_io_len(sector, ti) / PAGE_SECTORS;
+	if (len < 1)
+		goto out;
+	nr_pages = min(len, nr_pages);
 	if (ti->type->direct_access)
-		ret = ti->type->direct_access(ti, sector, kaddr, pfn, size);
-out:
+		ret = ti->type->direct_access(ti, pgoff, nr_pages, kaddr, pfn);
+
+ out:
 	dm_put_live_table(md, srcu_idx);
-	return min(ret, size);
+
+	return ret;
 }
 
 /*
@@ -1437,6 +1459,7 @@ static int next_free_minor(int *minor)
 }
 
 static const struct block_device_operations dm_blk_dops;
+static const struct dax_operations dm_dax_ops;
 
 static void dm_wq_work(struct work_struct *work);
 
@@ -1483,6 +1506,12 @@ static void cleanup_mapped_device(struct mapped_device *md)
 	if (md->bs)
 		bioset_free(md->bs);
 
+	if (md->dax_dev) {
+		kill_dax(md->dax_dev);
+		put_dax(md->dax_dev);
+		md->dax_dev = NULL;
+	}
+
 	if (md->disk) {
 		spin_lock(&_minor_lock);
 		md->disk->private_data = NULL;
@@ -1510,6 +1539,7 @@ static void cleanup_mapped_device(struct mapped_device *md)
 static struct mapped_device *alloc_dev(int minor)
 {
 	int r, numa_node_id = dm_get_numa_node();
+	struct dax_device *dax_dev;
 	struct mapped_device *md;
 	void *old_md;
 
@@ -1574,6 +1604,12 @@ static struct mapped_device *alloc_dev(int minor)
 	md->disk->queue = md->queue;
 	md->disk->private_data = md;
 	sprintf(md->disk->disk_name, "dm-%d", minor);
+
+	dax_dev = alloc_dax(md, md->disk->disk_name, &dm_dax_ops);
+	if (!dax_dev)
+		goto bad;
+	md->dax_dev = dax_dev;
+
 	add_disk(md->disk);
 	format_dev_t(md->name, MKDEV(_major, minor));
 
@@ -2775,12 +2811,15 @@ static const struct block_device_operations dm_blk_dops = {
 	.open = dm_blk_open,
 	.release = dm_blk_close,
 	.ioctl = dm_blk_ioctl,
-	.direct_access = dm_blk_direct_access,
 	.getgeo = dm_blk_getgeo,
 	.pr_ops = &dm_pr_ops,
 	.owner = THIS_MODULE
 };
 
+static const struct dax_operations dm_dax_ops = {
+	.direct_access = dm_dax_direct_access,
+};
+
 /*
  * module hooks
  */

drivers/misc/Kconfig

@@ -495,6 +495,7 @@ config VEXPRESS_SYSCFG
 config PANEL
 	tristate "Parallel port LCD/Keypad Panel support"
 	depends on PARPORT
+	select CHARLCD
 	---help---
 	  Say Y here if you have an HD44780 or KS-0074 LCD connected to your
 	  parallel port. This driver also features 4 and 6-key keypads. The LCD
@@ -771,6 +772,14 @@ config PANEL_BOOT_MESSAGE
 
 endif # PANEL
 
+config ASPEED_LPC_CTRL
+	depends on (ARCH_ASPEED || COMPILE_TEST) && REGMAP && MFD_SYSCON
+	tristate "Aspeed ast2400/2500 HOST LPC to BMC bridge control"
+	---help---
+	  Control Aspeed ast2400/2500 HOST LPC to BMC mappings through
+	  ioctl()s, the driver also provides a read/write interface to a BMC ram
+	  region where the host LPC read/write region can be buffered.
+
 source "drivers/misc/c2port/Kconfig"
 source "drivers/misc/eeprom/Kconfig"
 source "drivers/misc/cb710/Kconfig"

drivers/misc/Makefile

@@ -54,6 +54,7 @@ obj-$(CONFIG_ECHO)		+= echo/
 obj-$(CONFIG_VEXPRESS_SYSCFG)	+= vexpress-syscfg.o
 obj-$(CONFIG_CXL_BASE)		+= cxl/
 obj-$(CONFIG_PANEL)             += panel.o
+obj-$(CONFIG_ASPEED_LPC_CTRL)	+= aspeed-lpc-ctrl.o
 
 lkdtm-$(CONFIG_LKDTM)		+= lkdtm_core.o
 lkdtm-$(CONFIG_LKDTM)		+= lkdtm_bugs.o

drivers/nvdimm/Kconfig

@@ -20,6 +20,7 @@ if LIBNVDIMM
 config BLK_DEV_PMEM
 	tristate "PMEM: Persistent memory block device support"
 	default LIBNVDIMM
+	select DAX
 	select ND_BTT if BTT
 	select ND_PFN if NVDIMM_PFN
 	help

drivers/nvdimm/claim.c

@@ -246,7 +246,7 @@ static int nsio_rw_bytes(struct nd_namespace_common *ndns,
 	if (rw == READ) {
 		if (unlikely(is_bad_pmem(&nsio->bb, sector, sz_align)))
 			return -EIO;
-		return memcpy_from_pmem(buf, nsio->addr + offset, size);
+		return memcpy_mcsafe(buf, nsio->addr + offset, size);
 	}
 
 	if (unlikely(is_bad_pmem(&nsio->bb, sector, sz_align))) {

drivers/nvdimm/pmem.c

@@ -28,6 +28,7 @@
 #include <linux/pfn_t.h>
 #include <linux/slab.h>
 #include <linux/pmem.h>
+#include <linux/dax.h>
 #include <linux/nd.h>
 #include "pmem.h"
 #include "pfn.h"
@@ -88,7 +89,7 @@ static int read_pmem(struct page *page, unsigned int off,
 	int rc;
 	void *mem = kmap_atomic(page);
 
-	rc = memcpy_from_pmem(mem + off, pmem_addr, len);
+	rc = memcpy_mcsafe(mem + off, pmem_addr, len);
 	kunmap_atomic(mem);
 	if (rc)
 		return -EIO;
@@ -199,13 +200,13 @@ static int pmem_rw_page(struct block_device *bdev, sector_t sector,
 }
 
 /* see "strong" declaration in tools/testing/nvdimm/pmem-dax.c */
-__weak long pmem_direct_access(struct block_device *bdev, sector_t sector,
-		      void **kaddr, pfn_t *pfn, long size)
+__weak long __pmem_direct_access(struct pmem_device *pmem, pgoff_t pgoff,
+		long nr_pages, void **kaddr, pfn_t *pfn)
 {
-	struct pmem_device *pmem = bdev->bd_queue->queuedata;
-	resource_size_t offset = sector * 512 + pmem->data_offset;
+	resource_size_t offset = PFN_PHYS(pgoff) + pmem->data_offset;
 
-	if (unlikely(is_bad_pmem(&pmem->bb, sector, size)))
+	if (unlikely(is_bad_pmem(&pmem->bb, PFN_PHYS(pgoff) / 512,
+					PFN_PHYS(nr_pages))))
 		return -EIO;
 	*kaddr = pmem->virt_addr + offset;
 	*pfn = phys_to_pfn_t(pmem->phys_addr + offset, pmem->pfn_flags);
@@ -215,26 +216,41 @@ __weak long pmem_direct_access(struct block_device *bdev, sector_t sector,
 	 * requested range.
 	 */
 	if (unlikely(pmem->bb.count))
-		return size;
-	return pmem->size - pmem->pfn_pad - offset;
+		return nr_pages;
+	return PHYS_PFN(pmem->size - pmem->pfn_pad - offset);
 }
 
 static const struct block_device_operations pmem_fops = {
 	.owner =		THIS_MODULE,
 	.rw_page =		pmem_rw_page,
-	.direct_access =	pmem_direct_access,
 	.revalidate_disk =	nvdimm_revalidate_disk,
 };
 
+static long pmem_dax_direct_access(struct dax_device *dax_dev,
+		pgoff_t pgoff, long nr_pages, void **kaddr, pfn_t *pfn)
+{
+	struct pmem_device *pmem = dax_get_private(dax_dev);
+
+	return __pmem_direct_access(pmem, pgoff, nr_pages, kaddr, pfn);
+}
+
+static const struct dax_operations pmem_dax_ops = {
+	.direct_access = pmem_dax_direct_access,
+};
+
 static void pmem_release_queue(void *q)
 {
 	blk_cleanup_queue(q);
 }
 
-static void pmem_release_disk(void *disk)
+static void pmem_release_disk(void *__pmem)
 {
-	del_gendisk(disk);
-	put_disk(disk);
+	struct pmem_device *pmem = __pmem;
+
+	kill_dax(pmem->dax_dev);
+	put_dax(pmem->dax_dev);
+	del_gendisk(pmem->disk);
+	put_disk(pmem->disk);
 }
 
 static int pmem_attach_disk(struct device *dev,
@@ -245,6 +261,7 @@ static int pmem_attach_disk(struct device *dev,
 	struct vmem_altmap __altmap, *altmap = NULL;
 	struct resource *res = &nsio->res;
 	struct nd_pfn *nd_pfn = NULL;
+	struct dax_device *dax_dev;
 	int nid = dev_to_node(dev);
 	struct nd_pfn_sb *pfn_sb;
 	struct pmem_device *pmem;
@@ -325,6 +342,7 @@ static int pmem_attach_disk(struct device *dev,
 	disk = alloc_disk_node(0, nid);
 	if (!disk)
 		return -ENOMEM;
+	pmem->disk = disk;
 
 	disk->fops		= &pmem_fops;
 	disk->queue		= q;
@@ -336,9 +354,16 @@ static int pmem_attach_disk(struct device *dev,
 		return -ENOMEM;
 	nvdimm_badblocks_populate(nd_region, &pmem->bb, res);
 	disk->bb = &pmem->bb;
-	device_add_disk(dev, disk);
 
-	if (devm_add_action_or_reset(dev, pmem_release_disk, disk))
+	dax_dev = alloc_dax(pmem, disk->disk_name, &pmem_dax_ops);
+	if (!dax_dev) {
+		put_disk(disk);
+		return -ENOMEM;
+	}
+	pmem->dax_dev = dax_dev;
+
+	device_add_disk(dev, disk);
+	if (devm_add_action_or_reset(dev, pmem_release_disk, pmem))
 		return -ENOMEM;
 
 	revalidate_disk(disk);

drivers/nvdimm/pmem.h

@@ -5,8 +5,6 @@
 #include <linux/pfn_t.h>
 #include <linux/fs.h>
 
-long pmem_direct_access(struct block_device *bdev, sector_t sector,
-		      void **kaddr, pfn_t *pfn, long size);
 /* this definition is in it's own header for tools/testing/nvdimm to consume */
 struct pmem_device {
 	/* One contiguous memory region per device */
@@ -20,5 +18,10 @@ struct pmem_device {
 	/* trim size when namespace capacity has been section aligned */
 	u32			pfn_pad;
 	struct badblocks	bb;
+	struct dax_device	*dax_dev;
+	struct gendisk		*disk;
 };
+
+long __pmem_direct_access(struct pmem_device *pmem, pgoff_t pgoff,
+		long nr_pages, void **kaddr, pfn_t *pfn);
 #endif /* __NVDIMM_PMEM_H__ */

drivers/rapidio/rio.c

@@ -192,8 +192,6 @@ int rio_add_device(struct rio_dev *rdev)
 	}
 	spin_unlock(&rio_global_list_lock);
 
-	rio_create_sysfs_dev_files(rdev);
-
 	return 0;
 }
 EXPORT_SYMBOL_GPL(rio_add_device);
@@ -220,7 +218,6 @@ void rio_del_device(struct rio_dev *rdev, enum rio_device_state state)
 		}
 	}
 	spin_unlock(&rio_global_list_lock);
-	rio_remove_sysfs_dev_files(rdev);
 	device_unregister(&rdev->dev);
 }
 EXPORT_SYMBOL_GPL(rio_del_device);

drivers/rapidio/rio.h

@@ -27,8 +27,6 @@ extern u32 rio_mport_get_efb(struct rio_mport *port, int local, u16 destid,
 			     u8 hopcount, u32 from);
 extern int rio_mport_chk_dev_access(struct rio_mport *mport, u16 destid,
 				    u8 hopcount);
-extern int rio_create_sysfs_dev_files(struct rio_dev *rdev);
-extern void rio_remove_sysfs_dev_files(struct rio_dev *rdev);
 extern int rio_lock_device(struct rio_mport *port, u16 destid,
 			u8 hopcount, int wait_ms);
 extern int rio_unlock_device(struct rio_mport *port, u16 destid, u8 hopcount);

drivers/s390/block/Kconfig

@@ -14,6 +14,7 @@ config BLK_DEV_XPRAM
 
 config DCSSBLK
 	def_tristate m
+	select DAX
 	prompt "DCSSBLK support"
 	depends on S390 && BLOCK
 	help

drivers/w1/slaves/Kconfig

@@ -86,6 +86,12 @@ config W1_SLAVE_DS2433_CRC
 	  Each block has 30 bytes of data and a two byte CRC16.
 	  Full block writes are only allowed if the CRC is valid.
 
+config W1_SLAVE_DS2438
+	tristate "DS2438 Smart Battery Monitor 0x26 family support"
+	help
+	  Say Y here if you want to use a 1-wire
+	  DS2438 Smart Battery Monitor device support
+
 config W1_SLAVE_DS2760
 	tristate "Dallas 2760 battery monitor chip (HP iPAQ & others)"
 	help

drivers/w1/slaves/Makefile

@@ -11,6 +11,7 @@ obj-$(CONFIG_W1_SLAVE_DS2406)	+= w1_ds2406.o
 obj-$(CONFIG_W1_SLAVE_DS2423)	+= w1_ds2423.o
 obj-$(CONFIG_W1_SLAVE_DS2431)	+= w1_ds2431.o
 obj-$(CONFIG_W1_SLAVE_DS2433)	+= w1_ds2433.o
+obj-$(CONFIG_W1_SLAVE_DS2438)	+= w1_ds2438.o
 obj-$(CONFIG_W1_SLAVE_DS2760)	+= w1_ds2760.o
 obj-$(CONFIG_W1_SLAVE_DS2780)	+= w1_ds2780.o
 obj-$(CONFIG_W1_SLAVE_DS2781)	+= w1_ds2781.o

drivers/w1/slaves/w1_ds2760.h

@@ -24,11 +24,13 @@
 #define DS2760_DATA_SIZE		0x40
 
 #define DS2760_PROTECTION_REG		0x00
+
 #define DS2760_STATUS_REG		0x01
-	#define DS2760_STATUS_IE	(1 << 2)
-	#define DS2760_STATUS_SWEN	(1 << 3)
-	#define DS2760_STATUS_RNAOP	(1 << 4)
-	#define DS2760_STATUS_PMOD	(1 << 5)
+#define DS2760_STATUS_IE		(1 << 2)
+#define DS2760_STATUS_SWEN		(1 << 3)
+#define DS2760_STATUS_RNAOP		(1 << 4)
+#define DS2760_STATUS_PMOD		(1 << 5)
+
 #define DS2760_EEPROM_REG		0x07
 #define DS2760_SPECIAL_FEATURE_REG	0x08
 #define DS2760_VOLTAGE_MSB		0x0c

drivers/w1/w1_family.h

@@ -29,6 +29,7 @@
 #define W1_COUNTER_DS2423	0x1D
 #define W1_THERM_DS1822  	0x22
 #define W1_EEPROM_DS2433  	0x23
+#define W1_FAMILY_DS2438	0x26
 #define W1_THERM_DS18B20 	0x28
 #define W1_FAMILY_DS2408	0x29
 #define W1_EEPROM_DS2431	0x2D

drivers/zorro/zorro.h

@@ -5,5 +5,4 @@ extern void zorro_name_device(struct zorro_dev *z);
 static inline void zorro_name_device(struct zorro_dev *dev) { }
 #endif
 
-extern int zorro_create_sysfs_dev_files(struct zorro_dev *z);
-
+extern const struct attribute_group *zorro_device_attribute_groups[];