Merge tag 'mfd-for-linus-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6

Pull MFD Fixes from Samuel Ortiz:
 - Three Palmas fixes, One of them being a build error fix.
 - Two mc13xx fixes.  One for fixing an SPI regmap configuration and
   another one for working around an i.Mx hardware bug.
 - One omap-usb regression fix.
 - One twl6040 build breakage fix.
 - One file deletion (ab5500-core.h) that was overlooked during the last
   merge window.

* tag 'mfd-for-linus-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: Add missing hunk to change palmas irq to clear on read
  mfd: Fix palmas regulator pdata missing
  mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix issues.
  mfd: Update twl6040 Kconfig to avoid build breakage
  mfd: Delete ab5500-core.h
  mfd: mc13xxx workaround SPI hardware bug on i.Mx
  mfd: Fix mc13xxx SPI regmap
  mfd: Add terminating entry for i2c_device_id palmas table

drivers/mfd/Kconfig

@@ -286,6 +286,7 @@ config TWL6040_CORE
 	depends on I2C=y && GENERIC_HARDIRQS
 	select MFD_CORE
 	select REGMAP_I2C
+	select IRQ_DOMAIN
 	default n
 	help
 	  Say yes here if you want support for Texas Instruments TWL6040 audio

drivers/mfd/ab5500-core.h

-/*
- * Copyright (C) 2011 ST-Ericsson
- * License terms: GNU General Public License (GPL) version 2
- * Shared definitions and data structures for the AB5500 MFD driver
- */
-
-/* Read/write operation values. */
-#define AB5500_PERM_RD (0x01)
-#define AB5500_PERM_WR (0x02)
-
-/* Read/write permissions. */
-#define AB5500_PERM_RO (AB5500_PERM_RD)
-#define AB5500_PERM_RW (AB5500_PERM_RD | AB5500_PERM_WR)
-
-#define AB5500_MASK_BASE (0x60)
-#define AB5500_MASK_END (0x79)
-#define AB5500_CHIP_ID (0x20)
-
-/**
- * struct ab5500_reg_range
- * @first: the first address of the range
- * @last: the last address of the range
- * @perm: access permissions for the range
- */
-struct ab5500_reg_range {
-	u8 first;
-	u8 last;
-	u8 perm;
-};
-
-/**
- * struct ab5500_i2c_ranges
- * @count: the number of ranges in the list
- * @range: the list of register ranges
- */
-struct ab5500_i2c_ranges {
-	u8 nranges;
-	u8 bankid;
-	const struct ab5500_reg_range *range;
-};
-
-/**
- * struct ab5500_i2c_banks
- * @count: the number of ranges in the list
- * @range: the list of register ranges
- */
-struct ab5500_i2c_banks {
-	u8 nbanks;
-	const struct ab5500_i2c_ranges *bank;
-};
-
-/**
- * struct ab5500_bank
- * @slave_addr: I2C slave_addr found in AB5500 specification
- * @name: Documentation name of the bank. For reference
- */
-struct ab5500_bank {
-	u8 slave_addr;
-	const char *name;
-};
-
-static const struct ab5500_bank bankinfo[AB5500_NUM_BANKS] = {
-	[AB5500_BANK_VIT_IO_I2C_CLK_TST_OTP] = {
-		AB5500_ADDR_VIT_IO_I2C_CLK_TST_OTP, "VIT_IO_I2C_CLK_TST_OTP"},
-	[AB5500_BANK_VDDDIG_IO_I2C_CLK_TST] = {
-		AB5500_ADDR_VDDDIG_IO_I2C_CLK_TST, "VDDDIG_IO_I2C_CLK_TST"},
-	[AB5500_BANK_VDENC] = {AB5500_ADDR_VDENC, "VDENC"},
-	[AB5500_BANK_SIM_USBSIM] = {AB5500_ADDR_SIM_USBSIM, "SIM_USBSIM"},
-	[AB5500_BANK_LED] = {AB5500_ADDR_LED, "LED"},
-	[AB5500_BANK_ADC] = {AB5500_ADDR_ADC, "ADC"},
-	[AB5500_BANK_RTC] = {AB5500_ADDR_RTC, "RTC"},
-	[AB5500_BANK_STARTUP] = {AB5500_ADDR_STARTUP, "STARTUP"},
-	[AB5500_BANK_DBI_ECI] = {AB5500_ADDR_DBI_ECI, "DBI-ECI"},
-	[AB5500_BANK_CHG] = {AB5500_ADDR_CHG, "CHG"},
-	[AB5500_BANK_FG_BATTCOM_ACC] = {
-		AB5500_ADDR_FG_BATTCOM_ACC, "FG_BATCOM_ACC"},
-	[AB5500_BANK_USB] = {AB5500_ADDR_USB, "USB"},
-	[AB5500_BANK_IT] = {AB5500_ADDR_IT, "IT"},
-	[AB5500_BANK_VIBRA] = {AB5500_ADDR_VIBRA, "VIBRA"},
-	[AB5500_BANK_AUDIO_HEADSETUSB] = {
-		AB5500_ADDR_AUDIO_HEADSETUSB, "AUDIO_HEADSETUSB"},
-};
-
-int ab5500_get_register_interruptible_raw(struct ab5500 *ab, u8 bank, u8 reg,
-	u8 *value);
-int ab5500_mask_and_set_register_interruptible_raw(struct ab5500 *ab, u8 bank,
-	u8 reg, u8 bitmask, u8 bitvalues);

drivers/mfd/mc13xxx-spi.c

@@ -49,10 +49,72 @@ static struct regmap_config mc13xxx_regmap_spi_config = {
 	.reg_bits = 7,
 	.pad_bits = 1,
 	.val_bits = 24,
+	.write_flag_mask = 0x80,
 
 	.max_register = MC13XXX_NUMREGS,
 
 	.cache_type = REGCACHE_NONE,
+	.use_single_rw = 1,
+};
+
+static int mc13xxx_spi_read(void *context, const void *reg, size_t reg_size,
+				void *val, size_t val_size)
+{
+	unsigned char w[4] = { *((unsigned char *) reg), 0, 0, 0};
+	unsigned char r[4];
+	unsigned char *p = val;
+	struct device *dev = context;
+	struct spi_device *spi = to_spi_device(dev);
+	struct spi_transfer t = {
+		.tx_buf = w,
+		.rx_buf = r,
+		.len = 4,
+	};
+
+	struct spi_message m;
+	int ret;
+
+	if (val_size != 3 || reg_size != 1)
+		return -ENOTSUPP;
+
+	spi_message_init(&m);
+	spi_message_add_tail(&t, &m);
+	ret = spi_sync(spi, &m);
+
+	memcpy(p, &r[1], 3);
+
+	return ret;
+}
+
+static int mc13xxx_spi_write(void *context, const void *data, size_t count)
+{
+	struct device *dev = context;
+	struct spi_device *spi = to_spi_device(dev);
+
+	if (count != 4)
+		return -ENOTSUPP;
+
+	return spi_write(spi, data, count);
+}
+
+/*
+ * We cannot use regmap-spi generic bus implementation here.
+ * The MC13783 chip will get corrupted if CS signal is deasserted
+ * and on i.Mx31 SoC (the target SoC for MC13783 PMIC) the SPI controller
+ * has the following errata (DSPhl22960):
+ * "The CSPI negates SS when the FIFO becomes empty with
+ * SSCTL= 0. Software cannot guarantee that the FIFO will not
+ * drain because of higher priority interrupts and the
+ * non-realtime characteristics of the operating system. As a
+ * result, the SS will negate before all of the data has been
+ * transferred to/from the peripheral."
+ * We workaround this by accessing the SPI controller with a
+ * single transfert.
+ */
+
+static struct regmap_bus regmap_mc13xxx_bus = {
+	.write = mc13xxx_spi_write,
+	.read = mc13xxx_spi_read,
 };
 
 static int mc13xxx_spi_probe(struct spi_device *spi)
@@ -73,12 +135,13 @@ static int mc13xxx_spi_probe(struct spi_device *spi)
 
 	dev_set_drvdata(&spi->dev, mc13xxx);
 	spi->mode = SPI_MODE_0 | SPI_CS_HIGH;
-	spi->bits_per_word = 32;
 
 	mc13xxx->dev = &spi->dev;
 	mutex_init(&mc13xxx->lock);
 
-	mc13xxx->regmap = regmap_init_spi(spi, &mc13xxx_regmap_spi_config);
+	mc13xxx->regmap = regmap_init(&spi->dev, &regmap_mc13xxx_bus, &spi->dev,
+					&mc13xxx_regmap_spi_config);
+
 	if (IS_ERR(mc13xxx->regmap)) {
 		ret = PTR_ERR(mc13xxx->regmap);
 		dev_err(mc13xxx->dev, "Failed to initialize register map: %d\n",

drivers/mfd/omap-usb-host.c

@@ -25,6 +25,7 @@
 #include <linux/clk.h>
 #include <linux/dma-mapping.h>
 #include <linux/spinlock.h>
+#include <linux/gpio.h>
 #include <plat/cpu.h>
 #include <plat/usb.h>
 #include <linux/pm_runtime.h>
@@ -500,8 +501,21 @@ static void omap_usbhs_init(struct device *dev)
 	dev_dbg(dev, "starting TI HSUSB Controller\n");
 
 	pm_runtime_get_sync(dev);
-	spin_lock_irqsave(&omap->lock, flags);
 
+	if (pdata->ehci_data->phy_reset) {
+		if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[0]))
+			gpio_request_one(pdata->ehci_data->reset_gpio_port[0],
+					 GPIOF_OUT_INIT_LOW, "USB1 PHY reset");
+
+		if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[1]))
+			gpio_request_one(pdata->ehci_data->reset_gpio_port[1],
+					 GPIOF_OUT_INIT_LOW, "USB2 PHY reset");
+
+		/* Hold the PHY in RESET for enough time till DIR is high */
+		udelay(10);
+	}
+
+	spin_lock_irqsave(&omap->lock, flags);
 	omap->usbhs_rev = usbhs_read(omap->uhh_base, OMAP_UHH_REVISION);
 	dev_dbg(dev, "OMAP UHH_REVISION 0x%x\n", omap->usbhs_rev);
 
@@ -581,9 +595,39 @@ static void omap_usbhs_init(struct device *dev)
 	}
 
 	spin_unlock_irqrestore(&omap->lock, flags);
+
+	if (pdata->ehci_data->phy_reset) {
+		/* Hold the PHY in RESET for enough time till
+		 * PHY is settled and ready
+		 */
+		udelay(10);
+
+		if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[0]))
+			gpio_set_value_cansleep
+				(pdata->ehci_data->reset_gpio_port[0], 1);
+
+		if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[1]))
+			gpio_set_value_cansleep
+				(pdata->ehci_data->reset_gpio_port[1], 1);
+	}
+
 	pm_runtime_put_sync(dev);
 }
 
+static void omap_usbhs_deinit(struct device *dev)
+{
+	struct usbhs_hcd_omap		*omap = dev_get_drvdata(dev);
+	struct usbhs_omap_platform_data	*pdata = &omap->platdata;
+
+	if (pdata->ehci_data->phy_reset) {
+		if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[0]))
+			gpio_free(pdata->ehci_data->reset_gpio_port[0]);
+
+		if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[1]))
+			gpio_free(pdata->ehci_data->reset_gpio_port[1]);
+	}
+}
+
 
 /**
  * usbhs_omap_probe - initialize TI-based HCDs
@@ -767,6 +811,7 @@ static int __devinit usbhs_omap_probe(struct platform_device *pdev)
 	goto end_probe;
 
 err_alloc:
+	omap_usbhs_deinit(&pdev->dev);
 	iounmap(omap->tll_base);
 
 err_tll:
@@ -818,6 +863,7 @@ static int __devexit usbhs_omap_remove(struct platform_device *pdev)
 {
 	struct usbhs_hcd_omap *omap = platform_get_drvdata(pdev);
 
+	omap_usbhs_deinit(&pdev->dev);
 	iounmap(omap->tll_base);
 	iounmap(omap->uhh_base);
 	clk_put(omap->init_60m_fclk);

drivers/mfd/palmas.c

@@ -356,7 +356,14 @@ static int __devinit palmas_i2c_probe(struct i2c_client *i2c,
 		}
 	}
 
-	ret = regmap_add_irq_chip(palmas->regmap[1], palmas->irq,
+	/* Change IRQ into clear on read mode for efficiency */
+	slave = PALMAS_BASE_TO_SLAVE(PALMAS_INTERRUPT_BASE);
+	addr = PALMAS_BASE_TO_REG(PALMAS_INTERRUPT_BASE, PALMAS_INT_CTRL);
+	reg = PALMAS_INT_CTRL_INT_CLEAR;
+
+	regmap_write(palmas->regmap[slave], addr, reg);
+
+	ret = regmap_add_irq_chip(palmas->regmap[slave], palmas->irq,
 			IRQF_ONESHOT | IRQF_TRIGGER_LOW, -1, &palmas_irq_chip,
 			&palmas->irq_data);
 	if (ret < 0)
@@ -441,6 +448,9 @@ static int __devinit palmas_i2c_probe(struct i2c_client *i2c,
 		goto err;
 	}
 
+	children[PALMAS_PMIC_ID].platform_data = pdata->pmic_pdata;
+	children[PALMAS_PMIC_ID].pdata_size = sizeof(*pdata->pmic_pdata);
+
 	ret = mfd_add_devices(palmas->dev, -1,
 			      children, ARRAY_SIZE(palmas_children),
 			      NULL, regmap_irq_chip_get_base(palmas->irq_data));
@@ -472,6 +482,7 @@ static const struct i2c_device_id palmas_i2c_id[] = {
 	{ "twl6035", },
 	{ "twl6037", },
 	{ "tps65913", },
+	{ /* end */ }
 };
 MODULE_DEVICE_TABLE(i2c, palmas_i2c_id);
 

drivers/usb/host/ehci-omap.c

@@ -281,14 +281,13 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
 		}
 	}
 
+	/* Hold PHYs in reset while initializing EHCI controller */
 	if (pdata->phy_reset) {
 		if (gpio_is_valid(pdata->reset_gpio_port[0]))
-			gpio_request_one(pdata->reset_gpio_port[0],
-					 GPIOF_OUT_INIT_LOW, "USB1 PHY reset");
+			gpio_set_value_cansleep(pdata->reset_gpio_port[0], 0);
 
 		if (gpio_is_valid(pdata->reset_gpio_port[1]))
-			gpio_request_one(pdata->reset_gpio_port[1],
-					 GPIOF_OUT_INIT_LOW, "USB2 PHY reset");
+			gpio_set_value_cansleep(pdata->reset_gpio_port[1], 0);
 
 		/* Hold the PHY in RESET for enough time till DIR is high */
 		udelay(10);
@@ -330,6 +329,11 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
 	omap_ehci->hcs_params = readl(&omap_ehci->caps->hcs_params);
 
 	ehci_reset(omap_ehci);
+	ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
+	if (ret) {
+		dev_err(dev, "failed to add hcd with err %d\n", ret);
+		goto err_add_hcd;
+	}
 
 	if (pdata->phy_reset) {
 		/* Hold the PHY in RESET for enough time till
@@ -344,12 +348,6 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
 			gpio_set_value_cansleep(pdata->reset_gpio_port[1], 1);
 	}
 
-	ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
-	if (ret) {
-		dev_err(dev, "failed to add hcd with err %d\n", ret);
-		goto err_add_hcd;
-	}
-
 	/* root ports should always stay powered */
 	ehci_port_power(omap_ehci, 1);