Merge tag 'regulator-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator updates from Mark Brown:
 "This has been a very busy release for the core, some fixes, one large
  new feature and a big bit of refactoring to update the GPIO API:

   - Support for coupled regulators from Dmitry Osipenko based on a
     prior attempt by Maciej Purski, allowing us to handle situations
     where the voltages on two regulators can't be too far apart from
     each other.

   - Conversion of the GPIO support in both drivers and the core to use
     GPIO descriptors rather than numbers, part of the overall project
     to remove GPIO numbers.

   - Support for standby mode suspend states from Andrei Stefanescu.

   - New drivers for Allwinner AXP209, Cirrus Logic Lochnagar and
     Microchip MPC16502"

* tag 'regulator-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (90 commits)
  regulator: tps65910: fix a missing check of return value
  regulator: mcp16502: Select REGMAP_I2C to fix build error
  regulator: convert to DEFINE_SHOW_ATTRIBUTE
  regulator: mcp16502: Fix missing n_voltages setting
  regulator: mcp16502: Use #ifdef CONFIG_PM_SLEEP around mcp16502_suspend/resume_noirq
  regulator: mcp16502: code cleanup
  regulator: act8945a-regulator: make symbol act8945a_pm static
  drivers/regulator: fix a missing check of return value
  regulator: act8945a-regulator: fix 'defined but not used' compiler warning
  regulator: axp20x: fix set_ramp_delay for AXP209/dcdc2
  regulator: mcp16502: add support for suspend
  mfd: axp20x: use explicit bit defines
  mfd: axp20x: Clean up included headers
  regulator: dts: enable soft-start and ramp delay for the OLinuXino Lime2
  dt-bindings: mfd: axp20x: Add software based soft_start for AXP209 LDO3
  regulator: axp20x: add software based soft_start for AXP209 LDO3
  dt-bindings: mfd: axp20x: add support for regulator-ramp-delay for AXP209
  regulator: axp20x: add support for set_ramp_delay for AXP209
  mfd: axp20x: name voltage ramping define properly
  regulator: mcp16502: add regulator driver for MCP16502
  ...

Documentation/devicetree/bindings/mfd/axp20x.txt

@@ -32,6 +32,15 @@ Required properties:
 - interrupt-controller: The PMIC has its own internal IRQs
 - #interrupt-cells: Should be set to 1
 
+Supported common regulator properties, see ../regulator/regulator.txt for
+more information:
+- regulator-ramp-delay: sets the ramp up delay in uV/us
+			AXP20x/DCDC2: 1600, 800
+			AXP20x/LDO3:  1600, 800
+- regulator-soft-start:	enable the output at the lowest possible voltage and
+			only then set the desired voltage
+			AXP20x/LDO3: software-based implementation
+
 Optional properties:
 - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
 		      AXP152/20X: range:  750-1875, Default: 1.5 MHz

Documentation/devicetree/bindings/regulator/act8945a-regulator.txt

@@ -15,11 +15,17 @@ Optional input supply properties:
   - inl67-supply: The input supply for REG_LDO3 and REG_LDO4
 
 Any standard regulator properties can be used to configure the single regulator.
+regulator-initial-mode, regulator-allowed-modes and regulator-mode could be
+specified using mode values from dt-bindings/regulator/active-semi,8945a-regulator.h
+file.
 
 The valid names for regulators are:
 	REG_DCDC1, REG_DCDC2, REG_DCDC3, REG_LDO1, REG_LDO2, REG_LDO3, REG_LDO4.
 
 Example:
+
+#include <dt-bindings/regulator/active-semi,8945a-regulator.h>
+
 	pmic@5b {
 		compatible = "active-semi,act8945a";
 		reg = <0x5b>;
@@ -32,6 +38,18 @@ Example:
 				regulator-min-microvolt = <1350000>;
 				regulator-max-microvolt = <1350000>;
 				regulator-always-on;
+
+				regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_FIXED>,
+							  <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				regulator-initial-mode = <ACT8945A_REGULATOR_MODE_FIXED>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-min-microvolt=<1400000>;
+					regulator-suspend-max-microvolt=<1400000>;
+					regulator-changeable-in-suspend;
+					regulator-mode=<ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				};
 			};
 
 			vdd_1v2_reg: REG_DCDC2 {
@@ -39,6 +57,14 @@ Example:
 				regulator-min-microvolt = <1100000>;
 				regulator-max-microvolt = <1300000>;
 				regulator-always-on;
+
+				regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_FIXED>,
+							  <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				regulator-initial-mode = <ACT8945A_REGULATOR_MODE_FIXED>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
 			};
 
 			vdd_3v3_reg: REG_DCDC3 {
@@ -53,6 +79,14 @@ Example:
 				regulator-min-microvolt = <2500000>;
 				regulator-max-microvolt = <2500000>;
 				regulator-always-on;
+
+				regulator-allowed-modes = <ACT8945A_REGULATOR_MODE_NORMAL>,
+							  <ACT8945A_REGULATOR_MODE_LOWPOWER>;
+				regulator-initial-mode = <ACT8945A_REGULATOR_MODE_NORMAL>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
 			};
 
 			vdd_3v3_lp_reg: REG_LDO2 {

Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt

+Cirrus Logic Lochnagar Audio Development Board
+
+Lochnagar is an evaluation and development board for Cirrus Logic
+Smart CODEC and Amp devices. It allows the connection of most Cirrus
+Logic devices on mini-cards, as well as allowing connection of
+various application processor systems to provide a full evaluation
+platform.  Audio system topology, clocking and power can all be
+controlled through the Lochnagar, allowing the device under test
+to be used in a variety of possible use cases.
+
+This binding document describes the binding for the regulator portion
+of the driver.
+
+Also see these documents for generic binding information:
+  [1] Regulator: ../regulator/regulator.txt
+
+This binding must be part of the Lochnagar MFD binding:
+  [2] ../mfd/cirrus,lochnagar.txt
+
+Optional sub-nodes:
+
+  - VDDCORE : Initialisation data for the VDDCORE regulator, which
+    supplies the CODECs digital core if it has no build regulator for that
+    purpose.
+      Required Properties:
+      - compatible : One of the following strings:
+                     "cirrus,lochnagar2-vddcore"
+      - SYSVDD-supply: Primary power supply for the Lochnagar.
+
+  - MICVDD : Initialisation data for the MICVDD regulator, which
+    supplies the CODECs MICVDD.
+      Required Properties:
+      - compatible : One of the following strings:
+                     "cirrus,lochnagar2-micvdd"
+      - SYSVDD-supply: Primary power supply for the Lochnagar.
+
+  - MIC1VDD, MIC2VDD : Initialisation data for the MICxVDD supplies.
+      Required Properties:
+      - compatible : One of the following strings:
+                     "cirrus,lochnagar2-mic1vdd", "cirrus,lochnagar2-mic2vdd"
+      Optional Properties:
+      - cirrus,micbias-input : A property selecting which of the CODEC
+        minicard micbias outputs should be used, valid values are 1 - 4.
+      - MICBIAS1-supply, MICBIAS2-supply: Regulator supplies for the
+        MICxVDD outputs, supplying the digital microphones, normally
+        supplied from the attached CODEC.
+
+  - VDD1V8 : Recommended fixed regulator for the VDD1V8 regulator, which supplies the
+    CODECs analog and 1.8V digital supplies.
+      Required Properties:
+      - compatible : Should be set to "regulator-fixed"
+      - regulator-min-microvolt : Should be set to 1.8V
+      - regulator-max-microvolt : Should be set to 1.8V
+      - regulator-boot-on
+      - regulator-always-on
+      - vin-supply : Should be set to same supply as SYSVDD
+
+Example:
+
+lochnagar {
+	lochnagar-micvdd: MICVDD {
+		compatible = "cirrus,lochnagar2-micvdd";
+
+		SYSVDD-supply = <&wallvdd>;
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	lochnagar-vdd1v8: VDD1V8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VDD1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+
+		vin-supply = <&wallvdd>;
+	};
+};
+

Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt

+MCP16502 PMIC
+
+Required properties:
+- compatible: "microchip,mcp16502"
+- reg: I2C slave address
+- lpm-gpios: GPIO for LPM pin. Note that this GPIO *must* remain high during
+	     suspend-to-ram, keeping the PMIC into HIBERNATE mode.
+- regulators: A node that houses a sub-node for each regulator within
+              the device. Each sub-node is identified using the node's
+              name. The content of each sub-node is defined by the
+              standard binding for regulators; see regulator.txt.
+
+Regualtors of MCP16502 PMIC:
+1) VDD_IO	- Buck (1.2 - 3.7 V)
+2) VDD_DDR	- Buck (0.6 - 1.85 V)
+3) VDD_CORE	- Buck (0.6 - 1.85 V)
+4) VDD_OTHER	- BUCK (0.6 - 1.85 V)
+5) LDO1		- LDO  (1.2 - 3.7 V)
+6) LDO2		- LDO  (1.2 - 3.7 V)
+
+Regulator modes:
+2 - FPWM: higher precision, higher consumption
+4 - AutoPFM: lower precision, lower consumption
+
+Each regulator is defined using the standard binding for regulators.
+
+Example:
+
+mcp16502@5b {
+	compatible = "microchip,mcp16502";
+	reg = <0x5b>;
+	status = "okay";
+	lpm-gpios = <&pioBU 7 GPIO_ACTIVE_HIGH>;
+
+	regulators {
+		VDD_IO {
+			regulator-name = "VDD_IO";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		VDD_DDR {
+			regulator-name = "VDD_DDR";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1850000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		VDD_CORE {
+			regulator-name = "VDD_CORE";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1850000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		VDD_OTHER {
+			regulator-name = "VDD_OTHER";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1850000>;
+			regulator-initial-mode = <2>;
+			regulator-allowed-modes = <2>, <4>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+				regulator-mode = <4>;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+				regulator-mode = <4>;
+			};
+		};
+
+		LDO1 {
+			regulator-name = "LDO1";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+			};
+		};
+
+		LDO2 {
+			regulator-name = "LDO2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-always-on;
+
+			regulator-state-standby {
+				regulator-on-in-suspend;
+			};
+
+			regulator-state-mem {
+				regulator-off-in-suspend;
+			};
+		};
+
+	};
+};

Documentation/devicetree/bindings/regulator/regulator.txt

@@ -33,13 +33,16 @@ Optional properties:
   decreases of any level. This is useful for regulators with exponential
   voltage changes.
 - regulator-soft-start: Enable soft start so that voltage ramps slowly
+- regulator-state-standby sub-root node for Standby mode
+  : equivalent with standby Linux sleep state, which provides energy savings
+  with a relatively quick transition back time.
 - regulator-state-mem sub-root node for Suspend-to-RAM mode
   : suspend to memory, the device goes to sleep, but all data stored in memory,
   only some external interrupt can wake the device.
 - regulator-state-disk sub-root node for Suspend-to-DISK mode
   : suspend to disk, this state operates similarly to Suspend-to-RAM,
   but includes a final step of writing memory contents to disk.
-- regulator-state-[mem/disk] node has following common properties:
+- regulator-state-[mem/disk/standby] node has following common properties:
 	- regulator-on-in-suspend: regulator should be on in suspend state.
 	- regulator-off-in-suspend: regulator should be off in suspend state.
 	- regulator-suspend-min-microvolt: minimum voltage may be set in
@@ -76,8 +79,11 @@ Optional properties:
 - regulator-coupled-with: Regulators with which the regulator
   is coupled. The linkage is 2-way - all coupled regulators should be linked
   with each other. A regulator should not be coupled with its supplier.
-- regulator-coupled-max-spread: Max spread between voltages of coupled regulators
-  in microvolts.
+- regulator-coupled-max-spread: Array of maximum spread between voltages of
+  coupled regulators in microvolts, each value in the array relates to the
+  corresponding couple specified by the regulator-coupled-with property.
+- regulator-max-step-microvolt: Maximum difference between current and target
+  voltages that can be changed safely in a single step.
 
 Deprecated properties:
 - regulator-compatible: If a regulator chip contains multiple

Documentation/driver-model/devres.txt

@@ -254,6 +254,7 @@ GPIO
   devm_gpiod_get_index_optional()
   devm_gpiod_get_optional()
   devm_gpiod_put()
+  devm_gpiod_unhinge()
   devm_gpiochip_add_data()
   devm_gpiochip_remove()
   devm_gpio_request()

MAINTAINERS

@@ -9891,6 +9891,13 @@ M:	Ludovic Desroches <ludovic.desroches@microchip.com>
 S:	Maintained
 F:	drivers/mmc/host/atmel-mci.c
 
+MICROCHIP MCP16502 PMIC DRIVER
+M:	Andrei Stefanescu <andrei.stefanescu@microchip.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+F:	Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt
+F:	drivers/regulator/mcp16502.c
+
 MICROCHIP MCP3911 ADC DRIVER
 M:	Marcus Folkesson <marcus.folkesson@gmail.com>
 M:	Kent Gustavsson <kent@minoris.se>

arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts

@@ -245,6 +245,8 @@ &reg_ldo3 {
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <2800000>;
 	regulator-name = "vddio-csi0";
+	regulator-soft-start;
+	regulator-ramp-delay = <1600>;
 };
 
 &reg_ldo4 {

arch/arm/mach-s3c64xx/mach-crag6410-module.c

@@ -194,8 +194,8 @@ static struct wm8994_pdata wm8994_pdata = {
 		0x3,          /* IRQ out, active high, CMOS */
 	},
 	.ldo = {
-		 { .enable = S3C64XX_GPN(6), .init_data = &wm8994_ldo1, },
-		 { .enable = S3C64XX_GPN(4), .init_data = &wm8994_ldo2, },
+		 { .init_data = &wm8994_ldo1, },
+		 { .init_data = &wm8994_ldo2, },
 	},
 };
 
@@ -203,6 +203,18 @@ static const struct i2c_board_info wm1277_devs[] = {
 	{ I2C_BOARD_INFO("wm8958", 0x1a),  /* WM8958 is the superset */
 	  .platform_data = &wm8994_pdata,
 	  .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2,
+	  .dev_name = "wm8958",
+	},
+};
+
+static struct gpiod_lookup_table wm8994_gpiod_table = {
+	.dev_id = "i2c-wm8958", /* I2C device name */
+	.table = {
+		GPIO_LOOKUP("GPION", 6,
+			    "wlf,ldo1ena", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("GPION", 4,
+			    "wlf,ldo2ena", GPIO_ACTIVE_HIGH),
+		{ },
 	},
 };
 
@@ -381,6 +393,7 @@ static int wlf_gf_module_probe(struct i2c_client *i2c,
 
 	gpiod_add_lookup_table(&wm5102_reva_gpiod_table);
 	gpiod_add_lookup_table(&wm5102_gpiod_table);
+	gpiod_add_lookup_table(&wm8994_gpiod_table);
 
 	if (i < ARRAY_SIZE(gf_mods)) {
 		dev_info(&i2c->dev, "%s revision %d\n",

drivers/gpio/gpiolib-devres.c

@@ -98,15 +98,28 @@ struct gpio_desc *__must_check devm_gpiod_get_index(struct device *dev,
 	struct gpio_desc **dr;
 	struct gpio_desc *desc;
 
+	desc = gpiod_get_index(dev, con_id, idx, flags);
+	if (IS_ERR(desc))
+		return desc;
+
+	/*
+	 * For non-exclusive GPIO descriptors, check if this descriptor is
+	 * already under resource management by this device.
+	 */
+	if (flags & GPIOD_FLAGS_BIT_NONEXCLUSIVE) {
+		struct devres *dres;
+
+		dres = devres_find(dev, devm_gpiod_release,
+				   devm_gpiod_match, &desc);
+		if (dres)
+			return desc;
+	}
+
 	dr = devres_alloc(devm_gpiod_release, sizeof(struct gpio_desc *),
 			  GFP_KERNEL);
-	if (!dr)
+	if (!dr) {
+		gpiod_put(desc);
 		return ERR_PTR(-ENOMEM);
-
-	desc = gpiod_get_index(dev, con_id, idx, flags);
-	if (IS_ERR(desc)) {
-		devres_free(dr);
-		return desc;
 	}
 
 	*dr = desc;
@@ -140,15 +153,28 @@ struct gpio_desc *devm_gpiod_get_from_of_node(struct device *dev,
 	struct gpio_desc **dr;
 	struct gpio_desc *desc;
 
+	desc = gpiod_get_from_of_node(node, propname, index, dflags, label);
+	if (IS_ERR(desc))
+		return desc;
+
+	/*
+	 * For non-exclusive GPIO descriptors, check if this descriptor is
+	 * already under resource management by this device.
+	 */
+	if (dflags & GPIOD_FLAGS_BIT_NONEXCLUSIVE) {
+		struct devres *dres;
+
+		dres = devres_find(dev, devm_gpiod_release,
+				   devm_gpiod_match, &desc);
+		if (dres)
+			return desc;
+	}
+
 	dr = devres_alloc(devm_gpiod_release, sizeof(struct gpio_desc *),
 			  GFP_KERNEL);
-	if (!dr)
+	if (!dr) {
+		gpiod_put(desc);
 		return ERR_PTR(-ENOMEM);
-
-	desc = gpiod_get_from_of_node(node, propname, index, dflags, label);
-	if (IS_ERR(desc)) {
-		devres_free(dr);
-		return desc;
 	}
 
 	*dr = desc;
@@ -320,6 +346,36 @@ void devm_gpiod_put(struct device *dev, struct gpio_desc *desc)
 }
 EXPORT_SYMBOL(devm_gpiod_put);
 
+/**
+ * devm_gpiod_unhinge - Remove resource management from a gpio descriptor
+ * @dev:	GPIO consumer
+ * @desc:	GPIO descriptor to remove resource management from
+ *
+ * Remove resource management from a GPIO descriptor. This is needed when
+ * you want to hand over lifecycle management of a descriptor to another
+ * mechanism.
+ */
+
+void devm_gpiod_unhinge(struct device *dev, struct gpio_desc *desc)
+{
+	int ret;
+
+	if (IS_ERR_OR_NULL(desc))
+		return;
+	ret = devres_destroy(dev, devm_gpiod_release,
+			     devm_gpiod_match, &desc);
+	/*
+	 * If the GPIO descriptor is requested as nonexclusive, we
+	 * may call this function several times on the same descriptor
+	 * so it is OK if devres_destroy() returns -ENOENT.
+	 */
+	if (ret == -ENOENT)
+		return;
+	/* Anything else we should warn about */
+	WARN_ON(ret);
+}
+EXPORT_SYMBOL(devm_gpiod_unhinge);
+
 /**
  * devm_gpiod_put_array - Resource-managed gpiod_put_array()
  * @dev:	GPIO consumer

drivers/gpio/gpiolib.c

@@ -4205,6 +4205,8 @@ struct gpio_desc *gpiod_get_from_of_node(struct device_node *node,
 	transitory = flags & OF_GPIO_TRANSITORY;
 
 	ret = gpiod_request(desc, label);
+	if (ret == -EBUSY && (flags & GPIOD_FLAGS_BIT_NONEXCLUSIVE))
+		return desc;
 	if (ret)
 		return ERR_PTR(ret);
 

drivers/gpio/gpiolib.h

@@ -201,12 +201,6 @@ int gpiod_set_array_value_complex(bool raw, bool can_sleep,
 				  struct gpio_array *array_info,
 				  unsigned long *value_bitmap);
 
-/* This is just passed between gpiolib and devres */
-struct gpio_desc *gpiod_get_from_of_node(struct device_node *node,
-					 const char *propname, int index,
-					 enum gpiod_flags dflags,
-					 const char *label);
-
 extern struct spinlock gpio_lock;
 extern struct list_head gpio_devices;
 

drivers/mfd/axp20x.c

@@ -16,20 +16,21 @@
  * published by the Free Software Foundation.
  */
 
-#include <linux/err.h>
+#include <linux/acpi.h>
+#include <linux/bitops.h>
 #include <linux/delay.h>
+#include <linux/err.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
+#include <linux/mfd/axp20x.h>
+#include <linux/mfd/core.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
-#include <linux/mfd/axp20x.h>
-#include <linux/mfd/core.h>
-#include <linux/of_device.h>
-#include <linux/acpi.h>
 
-#define AXP20X_OFF	0x80
+#define AXP20X_OFF	BIT(7)
 
 #define AXP806_REG_ADDR_EXT_ADDR_MASTER_MODE	0
 #define AXP806_REG_ADDR_EXT_ADDR_SLAVE_MODE	BIT(4)

drivers/mfd/wm8994-core.c

@@ -21,7 +21,6 @@
 #include <linux/mfd/core.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
-#include <linux/of_gpio.h>
 #include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
@@ -306,14 +305,6 @@ static int wm8994_set_pdata_from_of(struct wm8994 *wm8994)
 
 	pdata->csnaddr_pd = of_property_read_bool(np, "wlf,csnaddr-pd");
 
-	pdata->ldo[0].enable = of_get_named_gpio(np, "wlf,ldo1ena", 0);
-	if (pdata->ldo[0].enable < 0)
-		pdata->ldo[0].enable = 0;
-
-	pdata->ldo[1].enable = of_get_named_gpio(np, "wlf,ldo2ena", 0);
-	if (pdata->ldo[1].enable < 0)
-		pdata->ldo[1].enable = 0;
-
 	return 0;
 }
 #else

drivers/regulator/88pm8607.c

@@ -328,7 +328,7 @@ static int pm8607_regulator_dt_init(struct platform_device *pdev,
 		return -ENODEV;
 	}
 	for_each_child_of_node(nproot, np) {
-		if (!of_node_cmp(np->name, info->desc.name)) {
+		if (of_node_name_eq(np, info->desc.name)) {
 			config->init_data =
 				of_get_regulator_init_data(&pdev->dev, np,
 							   &info->desc);

drivers/regulator/Kconfig

@@ -567,6 +567,16 @@ config REGULATOR_MC13892
 	  Say y here to support the regulators found on the Freescale MC13892
 	  PMIC.
 
+config REGULATOR_MCP16502
+	tristate "Microchip MCP16502 PMIC"
+	depends on I2C && OF
+	select REGMAP_I2C
+	help
+	  Say y here to support the MCP16502 PMIC. This driver supports
+	  basic operations (get/set voltage, get/set operating mode)
+	  through the regulator interface. In addition it enables
+	  suspend-to-ram/standby transition.
+
 config REGULATOR_MT6311
 	tristate "MediaTek MT6311 PMIC"
 	depends on I2C

drivers/regulator/Makefile

@@ -74,6 +74,7 @@ obj-$(CONFIG_REGULATOR_MAX77802) += max77802-regulator.o
 obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o
 obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
 obj-$(CONFIG_REGULATOR_MC13XXX_CORE) +=  mc13xxx-regulator-core.o
+obj-$(CONFIG_REGULATOR_MCP16502) += mcp16502.o
 obj-$(CONFIG_REGULATOR_MT6311) += mt6311-regulator.o
 obj-$(CONFIG_REGULATOR_MT6323)	+= mt6323-regulator.o
 obj-$(CONFIG_REGULATOR_MT6380)	+= mt6380-regulator.o

drivers/regulator/act8945a-regulator.c

@@ -15,31 +15,41 @@
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
+#include <linux/regmap.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/machine.h>
+#include <dt-bindings/regulator/active-semi,8945a-regulator.h>
 
 /**
  * ACT8945A Global Register Map.
  */
 #define ACT8945A_SYS_MODE	0x00
 #define ACT8945A_SYS_CTRL	0x01
+#define ACT8945A_SYS_UNLK_REGS	0x0b
 #define ACT8945A_DCDC1_VSET1	0x20
 #define ACT8945A_DCDC1_VSET2	0x21
 #define ACT8945A_DCDC1_CTRL	0x22
+#define ACT8945A_DCDC1_SUS	0x24
 #define ACT8945A_DCDC2_VSET1	0x30
 #define ACT8945A_DCDC2_VSET2	0x31
 #define ACT8945A_DCDC2_CTRL	0x32
+#define ACT8945A_DCDC2_SUS	0x34
 #define ACT8945A_DCDC3_VSET1	0x40
 #define ACT8945A_DCDC3_VSET2	0x41
 #define ACT8945A_DCDC3_CTRL	0x42
+#define ACT8945A_DCDC3_SUS	0x44
 #define ACT8945A_LDO1_VSET	0x50
 #define ACT8945A_LDO1_CTRL	0x51
+#define ACT8945A_LDO1_SUS	0x52
 #define ACT8945A_LDO2_VSET	0x54
 #define ACT8945A_LDO2_CTRL	0x55
+#define ACT8945A_LDO2_SUS	0x56
 #define ACT8945A_LDO3_VSET	0x60
 #define ACT8945A_LDO3_CTRL	0x61
+#define ACT8945A_LDO3_SUS	0x62
 #define ACT8945A_LDO4_VSET	0x64
 #define ACT8945A_LDO4_CTRL	0x65
+#define ACT8945A_LDO4_SUS	0x66
 
 /**
  * Field Definitions.
@@ -60,7 +70,12 @@ enum {
 	ACT8945A_ID_LDO2,
 	ACT8945A_ID_LDO3,
 	ACT8945A_ID_LDO4,
-	ACT8945A_REG_NUM,
+	ACT8945A_ID_MAX,
+};
+
+struct act8945a_pmic {
+	struct regmap *regmap;
+	u32 op_mode[ACT8945A_ID_MAX];
 };
 
 static const struct regulator_linear_range act8945a_voltage_ranges[] = {
@@ -69,6 +84,143 @@ static const struct regulator_linear_range act8945a_voltage_ranges[] = {
 	REGULATOR_LINEAR_RANGE(2400000, 48, 63, 100000),
 };
 
+static int act8945a_set_suspend_state(struct regulator_dev *rdev, bool enable)
+{
+	struct regmap *regmap = rdev->regmap;
+	int id = rdev->desc->id, reg, val;
+
+	switch (id) {
+	case ACT8945A_ID_DCDC1:
+		reg = ACT8945A_DCDC1_SUS;
+		val = 0xa8;
+		break;
+	case ACT8945A_ID_DCDC2:
+		reg = ACT8945A_DCDC2_SUS;
+		val = 0xa8;
+		break;
+	case ACT8945A_ID_DCDC3:
+		reg = ACT8945A_DCDC3_SUS;
+		val = 0xa8;
+		break;
+	case ACT8945A_ID_LDO1:
+		reg = ACT8945A_LDO1_SUS;
+		val = 0xe8;
+		break;
+	case ACT8945A_ID_LDO2:
+		reg = ACT8945A_LDO2_SUS;
+		val = 0xe8;
+		break;
+	case ACT8945A_ID_LDO3:
+		reg = ACT8945A_LDO3_SUS;
+		val = 0xe8;
+		break;
+	case ACT8945A_ID_LDO4:
+		reg = ACT8945A_LDO4_SUS;
+		val = 0xe8;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (enable)
+		val |= BIT(4);
+
+	/*
+	 * Ask the PMIC to enable/disable this output when entering hibernate
+	 * mode.
+	 */
+	return regmap_write(regmap, reg, val);
+}
+
+static int act8945a_set_suspend_enable(struct regulator_dev *rdev)
+{
+	return act8945a_set_suspend_state(rdev, true);
+}
+
+static int act8945a_set_suspend_disable(struct regulator_dev *rdev)
+{
+	return act8945a_set_suspend_state(rdev, false);
+}
+
+static unsigned int act8945a_of_map_mode(unsigned int mode)
+{
+	switch (mode) {
+	case ACT8945A_REGULATOR_MODE_FIXED:
+	case ACT8945A_REGULATOR_MODE_NORMAL:
+		return REGULATOR_MODE_NORMAL;
+	case ACT8945A_REGULATOR_MODE_LOWPOWER:
+		return REGULATOR_MODE_STANDBY;
+	default:
+		return REGULATOR_MODE_INVALID;
+	}
+}
+
+static int act8945a_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	struct act8945a_pmic *act8945a = rdev_get_drvdata(rdev);
+	struct regmap *regmap = rdev->regmap;
+	int id = rdev->desc->id;
+	int reg, ret, val = 0;
+
+	switch (id) {
+	case ACT8945A_ID_DCDC1:
+		reg = ACT8945A_DCDC1_CTRL;
+		break;
+	case ACT8945A_ID_DCDC2:
+		reg = ACT8945A_DCDC2_CTRL;
+		break;
+	case ACT8945A_ID_DCDC3:
+		reg = ACT8945A_DCDC3_CTRL;
+		break;
+	case ACT8945A_ID_LDO1:
+		reg = ACT8945A_LDO1_SUS;
+		break;
+	case ACT8945A_ID_LDO2:
+		reg = ACT8945A_LDO2_SUS;
+		break;
+	case ACT8945A_ID_LDO3:
+		reg = ACT8945A_LDO3_SUS;
+		break;
+	case ACT8945A_ID_LDO4:
+		reg = ACT8945A_LDO4_SUS;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	switch (mode) {
+	case REGULATOR_MODE_STANDBY:
+		if (rdev->desc->id > ACT8945A_ID_DCDC3)
+			val = BIT(5);
+		break;
+	case REGULATOR_MODE_NORMAL:
+		if (rdev->desc->id <= ACT8945A_ID_DCDC3)
+			val = BIT(5);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	ret = regmap_update_bits(regmap, reg, BIT(5), val);
+	if (ret)
+		return ret;
+
+	act8945a->op_mode[id] = mode;
+
+	return 0;
+}
+
+static unsigned int act8945a_get_mode(struct regulator_dev *rdev)
+{
+	struct act8945a_pmic *act8945a = rdev_get_drvdata(rdev);
+	int id = rdev->desc->id;
+
+	if (id < ACT8945A_ID_DCDC1 || id >= ACT8945A_ID_MAX)
+		return -EINVAL;
+
+	return act8945a->op_mode[id];
+}
+
 static const struct regulator_ops act8945a_ops = {
 	.list_voltage		= regulator_list_voltage_linear_range,
 	.map_voltage		= regulator_map_voltage_linear_range,
@@ -76,7 +228,11 @@ static const struct regulator_ops act8945a_ops = {
 	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
 	.enable			= regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
+	.set_mode		= act8945a_set_mode,
+	.get_mode		= act8945a_get_mode,
 	.is_enabled		= regulator_is_enabled_regmap,
+	.set_suspend_enable	= act8945a_set_suspend_enable,
+	.set_suspend_disable	= act8945a_set_suspend_disable,
 };
 
 #define ACT89xx_REG(_name, _family, _id, _vsel_reg, _supply)		\
@@ -84,6 +240,7 @@ static const struct regulator_ops act8945a_ops = {
 		.name			= _name,			\
 		.supply_name		= _supply,			\
 		.of_match		= of_match_ptr("REG_"#_id),	\
+		.of_map_mode		= act8945a_of_map_mode,		\
 		.regulators_node	= of_match_ptr("regulators"),	\
 		.id			= _family##_ID_##_id,		\
 		.type			= REGULATOR_VOLTAGE,		\
@@ -122,10 +279,22 @@ static int act8945a_pmic_probe(struct platform_device *pdev)
 {
 	struct regulator_config config = { };
 	const struct regulator_desc *regulators;
+	struct act8945a_pmic *act8945a;
 	struct regulator_dev *rdev;
 	int i, num_regulators;
 	bool voltage_select;
 
+	act8945a = devm_kzalloc(&pdev->dev, sizeof(*act8945a), GFP_KERNEL);
+	if (!act8945a)
+		return -ENOMEM;
+
+	act8945a->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	if (!act8945a->regmap) {
+		dev_err(&pdev->dev,
+			"could not retrieve regmap from parent device\n");
+		return -EINVAL;
+	}
+
 	voltage_select = of_property_read_bool(pdev->dev.parent->of_node,
 					       "active-semi,vsel-high");
 
@@ -139,8 +308,10 @@ static int act8945a_pmic_probe(struct platform_device *pdev)
 
 	config.dev = &pdev->dev;
 	config.dev->of_node = pdev->dev.parent->of_node;
+	config.driver_data = act8945a;
 	for (i = 0; i < num_regulators; i++) {
-		rdev = devm_regulator_register(&pdev->dev, &regulators[i], &config);
+		rdev = devm_regulator_register(&pdev->dev, &regulators[i],
+					       &config);
 		if (IS_ERR(rdev)) {
 			dev_err(&pdev->dev,
 				"failed to register %s regulator\n",
@@ -149,14 +320,42 @@ static int act8945a_pmic_probe(struct platform_device *pdev)
 		}
 	}
 
-	return 0;
+	platform_set_drvdata(pdev, act8945a);
+
+	/* Unlock expert registers. */
+	return regmap_write(act8945a->regmap, ACT8945A_SYS_UNLK_REGS, 0xef);
+}
+
+static int __maybe_unused act8945a_suspend(struct device *pdev)
+{
+	struct act8945a_pmic *act8945a = dev_get_drvdata(pdev);
+
+	/*
+	 * Ask the PMIC to enter the suspend mode on the next PWRHLD
+	 * transition.
+	 */
+	return regmap_write(act8945a->regmap, ACT8945A_SYS_CTRL, 0x42);
+}
+
+static SIMPLE_DEV_PM_OPS(act8945a_pm, act8945a_suspend, NULL);
+
+static void act8945a_pmic_shutdown(struct platform_device *pdev)
+{
+	struct act8945a_pmic *act8945a = platform_get_drvdata(pdev);
+
+	/*
+	 * Ask the PMIC to shutdown everything on the next PWRHLD transition.
+	 */
+	regmap_write(act8945a->regmap, ACT8945A_SYS_CTRL, 0x0);
 }
 
 static struct platform_driver act8945a_pmic_driver = {
 	.driver = {
 		.name = "act8945a-regulator",
+		.pm = &act8945a_pm,
 	},
 	.probe = act8945a_pmic_probe,
+	.shutdown = act8945a_pmic_shutdown,
 };
 module_platform_driver(act8945a_pmic_driver);
 

drivers/regulator/arizona-ldo1.c

@@ -283,9 +283,6 @@ static int arizona_ldo1_common_init(struct platform_device *pdev,
 	of_node_put(config.of_node);
 
 	if (IS_ERR(ldo1->regulator)) {
-		if (config.ena_gpiod)
-			gpiod_put(config.ena_gpiod);
-
 		ret = PTR_ERR(ldo1->regulator);
 		dev_err(&pdev->dev, "Failed to register LDO1 supply: %d\n",
 			ret);

drivers/regulator/as3711-regulator.c

+// SPDX-License-Identifier: GPL-2.0
 /*
  * AS3711 PMIC regulator driver, using DCDC Step Down and LDO supplies
  *
  * Copyright (C) 2012 Renesas Electronics Corporation
  * Author: Guennadi Liakhovetski, <g.liakhovetski@gmx.de>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the version 2 of the GNU General Public License as
- * published by the Free Software Foundation
  */
 
 #include <linux/err.h>

drivers/regulator/bd718x7-regulator.c

@@ -9,6 +9,7 @@
 #include <linux/kernel.h>
 #include <linux/mfd/rohm-bd718x7.h>
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/machine.h>
@@ -130,6 +131,7 @@ static struct regulator_ops bd718xx_buck_regulator_nolinear_ops = {
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
 	.list_voltage = regulator_list_voltage_table,
+	.map_voltage = regulator_map_voltage_ascend,
 	.set_voltage_sel = bd718xx_set_voltage_sel_restricted,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.set_voltage_time_sel = regulator_set_voltage_time_sel,
@@ -1007,7 +1009,7 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 };
 
 struct bd718xx_pmic_inits {
-	const struct bd718xx_regulator_data (*r_datas)[];
+	const struct bd718xx_regulator_data *r_datas;
 	unsigned int r_amount;
 };
 
@@ -1017,11 +1019,11 @@ static int bd718xx_probe(struct platform_device *pdev)
 	struct regulator_config config = { 0 };
 	struct bd718xx_pmic_inits pmic_regulators[] = {
 		[BD718XX_TYPE_BD71837] = {
-			.r_datas = &bd71837_regulators,
+			.r_datas = bd71837_regulators,
 			.r_amount = ARRAY_SIZE(bd71837_regulators),
 		},
 		[BD718XX_TYPE_BD71847] = {
-			.r_datas = &bd71847_regulators,
+			.r_datas = bd71847_regulators,
 			.r_amount = ARRAY_SIZE(bd71847_regulators),
 		},
 	};
@@ -1053,13 +1055,36 @@ static int bd718xx_probe(struct platform_device *pdev)
 			BD718XX_REG_REGLOCK);
 	}
 
+	/* At poweroff transition PMIC HW disables EN bit for regulators but
+	 * leaves SEL bit untouched. So if state transition from POWEROFF
+	 * is done to SNVS - then all power rails controlled by SW (having
+	 * SEL bit set) stay disabled as EN is cleared. This may result boot
+	 * failure if any crucial systems are powered by these rails.
+	 *
+	 * Change the next stage from poweroff to be READY instead of SNVS
+	 * for all reset types because OTP loading at READY will clear SEL
+	 * bit allowing HW defaults for power rails to be used
+	 */
+	err = regmap_update_bits(mfd->regmap, BD718XX_REG_TRANS_COND1,
+				 BD718XX_ON_REQ_POWEROFF_MASK |
+				 BD718XX_SWRESET_POWEROFF_MASK |
+				 BD718XX_WDOG_POWEROFF_MASK |
+				 BD718XX_KEY_L_POWEROFF_MASK,
+				 BD718XX_POWOFF_TO_RDY);
+	if (err) {
+		dev_err(&pdev->dev, "Failed to change reset target\n");
+		goto err;
+	} else {
+		dev_dbg(&pdev->dev, "Changed all resets from SVNS to READY\n");
+	}
+
 	for (i = 0; i < pmic_regulators[mfd->chip_type].r_amount; i++) {
 
 		const struct regulator_desc *desc;
 		struct regulator_dev *rdev;
 		const struct bd718xx_regulator_data *r;
 
-		r = &(*pmic_regulators[mfd->chip_type].r_datas)[i];
+		r = &pmic_regulators[mfd->chip_type].r_datas[i];
 		desc = &r->desc;
 
 		config.dev = pdev->dev.parent;

drivers/regulator/bd9571mwv-regulator.c

+// SPDX-License-Identifier: GPL-2.0
 /*
  * ROHM BD9571MWV-M regulator driver
  *
  * Copyright (C) 2017 Marek Vasut <marek.vasut+renesas@gmail.com>
  *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether expressed or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License version 2 for more details.
- *
  * Based on the TPS65086 driver
  *
  * NOTE: VD09 is missing

drivers/regulator/da9052-regulator.c

@@ -435,7 +435,7 @@ static int da9052_regulator_probe(struct platform_device *pdev)
 			return -ENODEV;
 
 		for_each_child_of_node(nproot, np) {
-			if (!of_node_cmp(np->name,
+			if (of_node_name_eq(np,
 					 regulator->info->reg_desc.name)) {
 				config.init_data = of_get_regulator_init_data(
 					&pdev->dev, np,

drivers/regulator/da9210-regulator.c

@@ -131,7 +131,7 @@ static irqreturn_t da9210_irq_handler(int irq, void *data)
 	if (error < 0)
 		goto error_i2c;
 
-	mutex_lock(&chip->rdev->mutex);
+	regulator_lock(chip->rdev);
 
 	if (val & DA9210_E_OVCURR) {
 		regulator_notifier_call_chain(chip->rdev,
@@ -157,7 +157,7 @@ static irqreturn_t da9210_irq_handler(int irq, void *data)
 		handled |= DA9210_E_VMAX;
 	}
 
-	mutex_unlock(&chip->rdev->mutex);
+	regulator_unlock(chip->rdev);
 
 	if (handled) {
 		/* Clear handled events */

drivers/regulator/da9211-regulator.c

@@ -389,6 +389,12 @@ static int da9211_regulator_init(struct da9211 *chip)
 		else
 			config.ena_gpiod = NULL;
 
+		/*
+		 * Hand the GPIO descriptor management over to the regulator
+		 * core, remove it from GPIO devres management.
+		 */
+		if (config.ena_gpiod)
+			devm_gpiod_unhinge(chip->dev, config.ena_gpiod);
 		chip->rdev[i] = devm_regulator_register(chip->dev,
 			&da9211_regulators[i], &config);
 		if (IS_ERR(chip->rdev[i])) {

drivers/regulator/dbx500-prcmu.c

@@ -75,7 +75,7 @@ static struct ux500_regulator_debug {
 	u8 *state_after_suspend;
 } rdebug;
 
-static int ux500_regulator_power_state_cnt_print(struct seq_file *s, void *p)
+static int ux500_regulator_power_state_cnt_show(struct seq_file *s, void *p)
 {
 	/* print power state count */
 	seq_printf(s, "ux500-regulator power state count: %i\n",
@@ -83,23 +83,9 @@ static int ux500_regulator_power_state_cnt_print(struct seq_file *s, void *p)
 
 	return 0;
 }
+DEFINE_SHOW_ATTRIBUTE(ux500_regulator_power_state_cnt);
 
-static int ux500_regulator_power_state_cnt_open(struct inode *inode,
-	struct file *file)
-{
-	return single_open(file, ux500_regulator_power_state_cnt_print,
-		inode->i_private);
-}
-
-static const struct file_operations ux500_regulator_power_state_cnt_fops = {
-	.open = ux500_regulator_power_state_cnt_open,
-	.read = seq_read,
-	.llseek = seq_lseek,
-	.release = single_release,
-	.owner = THIS_MODULE,
-};
-
-static int ux500_regulator_status_print(struct seq_file *s, void *p)
+static int ux500_regulator_status_show(struct seq_file *s, void *p)
 {
 	int i;
 
@@ -122,20 +108,7 @@ static int ux500_regulator_status_print(struct seq_file *s, void *p)
 
 	return 0;
 }
-
-static int ux500_regulator_status_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, ux500_regulator_status_print,
-		inode->i_private);
-}
-
-static const struct file_operations ux500_regulator_status_fops = {
-	.open = ux500_regulator_status_open,
-	.read = seq_read,
-	.llseek = seq_lseek,
-	.release = single_release,
-	.owner = THIS_MODULE,
-};
+DEFINE_SHOW_ATTRIBUTE(ux500_regulator_status);
 
 int __attribute__((weak)) dbx500_regulator_testcase(
 	struct dbx500_regulator_info *regulator_info,

drivers/regulator/fixed.c

@@ -183,7 +183,11 @@ static int reg_fixed_voltage_probe(struct platform_device *pdev)
 	 */
 	gflags |= GPIOD_FLAGS_BIT_NONEXCLUSIVE;
 
-	cfg.ena_gpiod = devm_gpiod_get_optional(&pdev->dev, NULL, gflags);
+	/*
+	 * Do not use devm* here: the regulator core takes over the
+	 * lifecycle management of the GPIO descriptor.
+	 */
+	cfg.ena_gpiod = gpiod_get_optional(&pdev->dev, NULL, gflags);
 	if (IS_ERR(cfg.ena_gpiod))
 		return PTR_ERR(cfg.ena_gpiod);
 

drivers/regulator/internal.h

@@ -42,6 +42,8 @@ struct regulator {
 	unsigned int always_on:1;
 	unsigned int bypass:1;
 	int uA_load;
+	unsigned int enable_count;
+	unsigned int deferred_disables;
 	struct regulator_voltage voltage[REGULATOR_STATES_NUM];
 	const char *supply_name;
 	struct device_attribute dev_attr;

drivers/regulator/lm363x-regulator.c

@@ -224,13 +224,15 @@ static struct gpio_desc *lm363x_regulator_of_get_enable_gpio(struct device *dev,
 	/*
 	 * Check LCM_EN1/2_GPIO is configured.
 	 * Those pins are used for enabling VPOS/VNEG LDOs.
+	 * Do not use devm* here: the regulator core takes over the
+	 * lifecycle management of the GPIO descriptor.
 	 */
 	switch (id) {
 	case LM3632_LDO_POS:
-		return devm_gpiod_get_index_optional(dev, "enable", 0,
+		return gpiod_get_index_optional(dev, "enable", 0,
 				GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
 	case LM3632_LDO_NEG:
-		return devm_gpiod_get_index_optional(dev, "enable", 1,
+		return gpiod_get_index_optional(dev, "enable", 1,
 				GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
 	default:
 		return NULL;
@@ -263,6 +265,8 @@ static int lm363x_regulator_probe(struct platform_device *pdev)
 					 LM3632_EXT_EN_MASK,
 					 LM3632_EXT_EN_MASK);
 		if (ret) {
+			if (gpiod)
+				gpiod_put(gpiod);
 			dev_err(dev, "External pin err: %d\n", ret);
 			return ret;
 		}

drivers/regulator/lochnagar-regulator.c

@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/mutex.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 #include <linux/regulator/driver.h>
@@ -20,6 +21,8 @@
 #include <linux/regulator/of_regulator.h>
 
 #include <linux/mfd/lochnagar.h>
+#include <linux/mfd/lochnagar1_regs.h>
+#include <linux/mfd/lochnagar2_regs.h>
 
 static const struct regulator_ops lochnagar_micvdd_ops = {
 	.enable = regulator_enable_regmap,
@@ -212,28 +215,52 @@ static const struct regulator_desc lochnagar_regulators[] = {
 	},
 };
 
+static const struct of_device_id lochnagar_of_match[] = {
+	{
+		.compatible = "cirrus,lochnagar2-micvdd",
+		.data = &lochnagar_regulators[LOCHNAGAR_MICVDD],
+	},
+	{
+		.compatible = "cirrus,lochnagar2-mic1vdd",
+		.data = &lochnagar_regulators[LOCHNAGAR_MIC1VDD],
+	},
+	{
+		.compatible = "cirrus,lochnagar2-mic2vdd",
+		.data = &lochnagar_regulators[LOCHNAGAR_MIC1VDD],
+	},
+	{
+		.compatible = "cirrus,lochnagar2-vddcore",
+		.data = &lochnagar_regulators[LOCHNAGAR_VDDCORE],
+	},
+	{},
+};
+
 static int lochnagar_regulator_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct lochnagar *lochnagar = dev_get_drvdata(dev->parent);
 	struct regulator_config config = { };
+	const struct of_device_id *of_id;
+	const struct regulator_desc *desc;
 	struct regulator_dev *rdev;
-	int ret, i;
+	int ret;
 
-	config.dev = lochnagar->dev;
+	config.dev = dev;
 	config.regmap = lochnagar->regmap;
 	config.driver_data = lochnagar;
 
-	for (i = 0; i < ARRAY_SIZE(lochnagar_regulators); i++) {
-		const struct regulator_desc *desc = &lochnagar_regulators[i];
+	of_id = of_match_device(lochnagar_of_match, dev);
+	if (!of_id)
+		return -EINVAL;
 
-		rdev = devm_regulator_register(dev, desc, &config);
-		if (IS_ERR(rdev)) {
-			ret = PTR_ERR(rdev);
-			dev_err(dev, "Failed to register %s regulator: %d\n",
-				desc->name, ret);
-			return ret;
-		}
+	desc = of_id->data;
+
+	rdev = devm_regulator_register(dev, desc, &config);
+	if (IS_ERR(rdev)) {
+		ret = PTR_ERR(rdev);
+		dev_err(dev, "Failed to register %s regulator: %d\n",
+			desc->name, ret);
+		return ret;
 	}
 
 	return 0;
@@ -242,6 +269,7 @@ static int lochnagar_regulator_probe(struct platform_device *pdev)
 static struct platform_driver lochnagar_regulator_driver = {
 	.driver = {
 		.name = "lochnagar-regulator",
+		.of_match_table = of_match_ptr(lochnagar_of_match),
 	},
 
 	.probe = lochnagar_regulator_probe,

drivers/regulator/lp8788-ldo.c

@@ -501,8 +501,12 @@ static int lp8788_config_ldo_enable_mode(struct platform_device *pdev,
 		return 0;
 	}
 
-	/* FIXME: check default mode for GPIO here: high or low? */
-	ldo->ena_gpiod = devm_gpiod_get_index_optional(&pdev->dev,
+	/*
+	 * Do not use devm* here: the regulator core takes over the
+	 * lifecycle management of the GPIO descriptor.
+	 * FIXME: check default mode for GPIO here: high or low?
+	 */
+	ldo->ena_gpiod = gpiod_get_index_optional(&pdev->dev,
 					       "enable",
 					       enable_id,
 					       GPIOD_OUT_HIGH |

drivers/regulator/max77686-regulator.c

@@ -11,8 +11,7 @@
 #include <linux/kernel.h>
 #include <linux/bug.h>
 #include <linux/err.h>
-#include <linux/gpio.h>
-#include <linux/of_gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/slab.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
@@ -76,6 +75,7 @@ enum max77686_ramp_rate {
 };
 
 struct max77686_data {
+	struct device *dev;
 	DECLARE_BITMAP(gpio_enabled, MAX77686_REGULATORS);
 
 	/* Array indexed by regulator id */
@@ -250,26 +250,34 @@ static int max77686_of_parse_cb(struct device_node *np,
 		struct regulator_config *config)
 {
 	struct max77686_data *max77686 = config->driver_data;
+	int ret;
 
 	switch (desc->id) {
 	case MAX77686_BUCK8:
 	case MAX77686_BUCK9:
 	case MAX77686_LDO20 ... MAX77686_LDO22:
-		config->ena_gpio = of_get_named_gpio(np,
-					"maxim,ena-gpios", 0);
-		config->ena_gpio_flags = GPIOF_OUT_INIT_HIGH;
-		config->ena_gpio_initialized = true;
+		config->ena_gpiod = gpiod_get_from_of_node(np,
+				"maxim,ena",
+				0,
+				GPIOD_OUT_HIGH | GPIOD_FLAGS_BIT_NONEXCLUSIVE,
+				"max77686-regulator");
+		if (IS_ERR(config->ena_gpiod))
+			config->ena_gpiod = NULL;
 		break;
 	default:
 		return 0;
 	}
 
-	if (gpio_is_valid(config->ena_gpio)) {
+	if (config->ena_gpiod) {
 		set_bit(desc->id, max77686->gpio_enabled);
 
-		return regmap_update_bits(config->regmap, desc->enable_reg,
-					  desc->enable_mask,
-					  MAX77686_GPIO_CONTROL);
+		ret = regmap_update_bits(config->regmap, desc->enable_reg,
+					 desc->enable_mask,
+					 MAX77686_GPIO_CONTROL);
+		if (ret) {
+			gpiod_put(config->ena_gpiod);
+			config->ena_gpiod = NULL;
+		}
 	}
 
 	return 0;
@@ -507,6 +515,7 @@ static int max77686_pmic_probe(struct platform_device *pdev)
 	if (!max77686)
 		return -ENOMEM;
 
+	max77686->dev = &pdev->dev;
 	config.dev = iodev->dev;
 	config.regmap = iodev->regmap;
 	config.driver_data = max77686;

drivers/regulator/max8952.c

@@ -231,9 +231,13 @@ static int max8952_pmic_probe(struct i2c_client *client,
 	else
 		gflags = GPIOD_OUT_LOW;
 	gflags |= GPIOD_FLAGS_BIT_NONEXCLUSIVE;
-	gpiod = devm_gpiod_get_optional(&client->dev,
-					"max8952,en",
-					gflags);
+	/*
+	 * Do not use devm* here: the regulator core takes over the
+	 * lifecycle management of the GPIO descriptor.
+	 */
+	gpiod = gpiod_get_optional(&client->dev,
+				   "max8952,en",
+				   gflags);
 	if (IS_ERR(gpiod))
 		return PTR_ERR(gpiod);
 	if (gpiod)

drivers/regulator/max8973-regulator.c

@@ -808,7 +808,13 @@ static int max8973_probe(struct i2c_client *client,
 	config.of_node = client->dev.of_node;
 	config.regmap = max->regmap;
 
-	/* Register the regulators */
+	/*
+	 * Register the regulators
+	 * Turn the GPIO descriptor over to the regulator core for
+	 * lifecycle management if we pass an ena_gpiod.
+	 */
+	if (config.ena_gpiod)
+		devm_gpiod_unhinge(&client->dev, config.ena_gpiod);
 	rdev = devm_regulator_register(&client->dev, &max->desc, &config);
 	if (IS_ERR(rdev)) {
 		ret = PTR_ERR(rdev);

drivers/regulator/max8997-regulator.c

@@ -925,7 +925,7 @@ static int max8997_pmic_dt_parse_pdata(struct platform_device *pdev,
 	pdata->regulators = rdata;
 	for_each_child_of_node(regulators_np, reg_np) {
 		for (i = 0; i < ARRAY_SIZE(regulators); i++)
-			if (!of_node_cmp(reg_np->name, regulators[i].name))
+			if (of_node_name_eq(reg_np, regulators[i].name))
 				break;
 
 		if (i == ARRAY_SIZE(regulators)) {

drivers/regulator/mc13xxx-regulator-core.c

@@ -186,7 +186,7 @@ struct mc13xxx_regulator_init_data *mc13xxx_parse_regulators_dt(
 		for (i = 0; i < num_regulators; i++) {
 			if (!regulators[i].desc.name)
 				continue;
-			if (!of_node_cmp(child->name,
+			if (of_node_name_eq(child,
 					 regulators[i].desc.name)) {
 				p->id = i;
 				p->init_data = of_get_regulator_init_data(

drivers/regulator/of_regulator.c

@@ -20,6 +20,7 @@
 #include "internal.h"
 
 static const char *const regulator_states[PM_SUSPEND_MAX + 1] = {
+	[PM_SUSPEND_STANDBY]	= "regulator-state-standby",
 	[PM_SUSPEND_MEM]	= "regulator-state-mem",
 	[PM_SUSPEND_MAX]	= "regulator-state-disk",
 };
@@ -170,6 +171,10 @@ static void of_get_regulation_constraints(struct device_node *np,
 				  &pval))
 		constraints->max_spread = pval;
 
+	if (!of_property_read_u32(np, "regulator-max-step-microvolt",
+				  &pval))
+		constraints->max_uV_step = pval;
+
 	constraints->over_current_protection = of_property_read_bool(np,
 					"regulator-over-current-protection");
 
@@ -181,9 +186,11 @@ static void of_get_regulation_constraints(struct device_node *np,
 		case PM_SUSPEND_MAX:
 			suspend_state = &constraints->state_disk;
 			break;
+		case PM_SUSPEND_STANDBY:
+			suspend_state = &constraints->state_standby;
+			break;
 		case PM_SUSPEND_ON:
 		case PM_SUSPEND_TO_IDLE:
-		case PM_SUSPEND_STANDBY:
 		default:
 			continue;
 		}
@@ -364,24 +371,25 @@ int of_regulator_match(struct device *dev, struct device_node *node,
 }
 EXPORT_SYMBOL_GPL(of_regulator_match);
 
-struct regulator_init_data *regulator_of_get_init_data(struct device *dev,
-					    const struct regulator_desc *desc,
-					    struct regulator_config *config,
-					    struct device_node **node)
+struct device_node *regulator_of_get_init_node(struct device *dev,
+					       const struct regulator_desc *desc)
 {
 	struct device_node *search, *child;
-	struct regulator_init_data *init_data = NULL;
 	const char *name;
 
 	if (!dev->of_node || !desc->of_match)
 		return NULL;
 
-	if (desc->regulators_node)
+	if (desc->regulators_node) {
 		search = of_get_child_by_name(dev->of_node,
 					      desc->regulators_node);
-	else
+	} else {
 		search = of_node_get(dev->of_node);
 
+		if (!strcmp(desc->of_match, search->name))
+			return search;
+	}
+
 	if (!search) {
 		dev_dbg(dev, "Failed to find regulator container node '%s'\n",
 			desc->regulators_node);
@@ -393,35 +401,48 @@ struct regulator_init_data *regulator_of_get_init_data(struct device *dev,
 		if (!name)
 			name = child->name;
 
-		if (strcmp(desc->of_match, name))
-			continue;
+		if (!strcmp(desc->of_match, name))
+			return of_node_get(child);
+	}
 
-		init_data = of_get_regulator_init_data(dev, child, desc);
-		if (!init_data) {
-			dev_err(dev,
-				"failed to parse DT for regulator %pOFn\n",
-				child);
-			break;
-		}
+	of_node_put(search);
 
-		if (desc->of_parse_cb) {
-			if (desc->of_parse_cb(child, desc, config)) {
-				dev_err(dev,
-					"driver callback failed to parse DT for regulator %pOFn\n",
-					child);
-				init_data = NULL;
-				break;
-			}
-		}
+	return NULL;
+}
+
+struct regulator_init_data *regulator_of_get_init_data(struct device *dev,
+					    const struct regulator_desc *desc,
+					    struct regulator_config *config,
+					    struct device_node **node)
+{
+	struct device_node *child;
+	struct regulator_init_data *init_data = NULL;
 
-		of_node_get(child);
-		*node = child;
-		break;
+	child = regulator_of_get_init_node(dev, desc);
+	if (!child)
+		return NULL;
+
+	init_data = of_get_regulator_init_data(dev, child, desc);
+	if (!init_data) {
+		dev_err(dev, "failed to parse DT for regulator %pOFn\n", child);
+		goto error;
 	}
 
-	of_node_put(search);
+	if (desc->of_parse_cb && desc->of_parse_cb(child, desc, config)) {
+		dev_err(dev,
+			"driver callback failed to parse DT for regulator %pOFn\n",
+			child);
+		goto error;
+	}
+
+	*node = child;
 
 	return init_data;
+
+error:
+	of_node_put(child);
+
+	return NULL;
 }
 
 static int of_node_match(struct device *dev, const void *data)

drivers/regulator/palmas-regulator.c

@@ -443,13 +443,16 @@ static int palmas_ldo_write(struct palmas *palmas, unsigned int reg,
 static int palmas_set_mode_smps(struct regulator_dev *dev, unsigned int mode)
 {
 	int id = rdev_get_id(dev);
+	int ret;
 	struct palmas_pmic *pmic = rdev_get_drvdata(dev);
 	struct palmas_pmic_driver_data *ddata = pmic->palmas->pmic_ddata;
 	struct palmas_regs_info *rinfo = &ddata->palmas_regs_info[id];
 	unsigned int reg;
 	bool rail_enable = true;
 
-	palmas_smps_read(pmic->palmas, rinfo->ctrl_addr, &reg);
+	ret = palmas_smps_read(pmic->palmas, rinfo->ctrl_addr, &reg);
+	if (ret)
+		return ret;
 
 	reg &= ~PALMAS_SMPS12_CTRL_MODE_ACTIVE_MASK;
 

drivers/regulator/pfuze100-regulator.c

@@ -370,6 +370,7 @@ static struct pfuze_regulator pfuze100_regulators[] = {
 	PFUZE100_VGEN_REG(PFUZE100, VGEN4, PFUZE100_VGEN4VOL, 1800000, 3300000, 100000),
 	PFUZE100_VGEN_REG(PFUZE100, VGEN5, PFUZE100_VGEN5VOL, 1800000, 3300000, 100000),
 	PFUZE100_VGEN_REG(PFUZE100, VGEN6, PFUZE100_VGEN6VOL, 1800000, 3300000, 100000),
+	PFUZE100_COIN_REG(PFUZE100, COIN, PFUZE100_COINVOL, 0x7, pfuze100_coin),
 };
 
 static struct pfuze_regulator pfuze200_regulators[] = {
@@ -436,6 +437,7 @@ static struct of_regulator_match pfuze100_matches[] = {
 	{ .name = "vgen4",	},
 	{ .name = "vgen5",	},
 	{ .name = "vgen6",	},
+	{ .name = "coin",	},
 };
 
 /* PFUZE200 */

drivers/regulator/qcom-rpmh-regulator.c

@@ -410,7 +410,7 @@ static int rpmh_regulator_init_vreg(struct rpmh_vreg *vreg, struct device *dev,
 	vreg->dev = dev;
 
 	for (rpmh_data = pmic_rpmh_data; rpmh_data->name; rpmh_data++)
-		if (!strcmp(rpmh_data->name, node->name))
+		if (of_node_name_eq(node, rpmh_data->name))
 			break;
 
 	if (!rpmh_data->name) {

drivers/regulator/s2mps11.c

@@ -5,7 +5,7 @@
 
 #include <linux/bug.h>
 #include <linux/err.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/slab.h>
 #include <linux/module.h>
 #include <linux/of.h>
@@ -14,7 +14,6 @@
 #include <linux/regulator/driver.h>
 #include <linux/regulator/machine.h>
 #include <linux/regulator/of_regulator.h>
-#include <linux/of_gpio.h>
 #include <linux/mfd/samsung/core.h>
 #include <linux/mfd/samsung/s2mps11.h>
 #include <linux/mfd/samsung/s2mps13.h>
@@ -44,7 +43,7 @@ struct s2mps11_info {
 	 * Array (size: number of regulators) with GPIO-s for external
 	 * sleep control.
 	 */
-	int *ext_control_gpio;
+	struct gpio_desc **ext_control_gpiod;
 };
 
 static int get_ramp_delay(int ramp_delay)
@@ -511,7 +510,7 @@ static int s2mps14_regulator_enable(struct regulator_dev *rdev)
 	case S2MPS14X:
 		if (test_bit(rdev_get_id(rdev), s2mps11->suspend_state))
 			val = S2MPS14_ENABLE_SUSPEND;
-		else if (gpio_is_valid(s2mps11->ext_control_gpio[rdev_get_id(rdev)]))
+		else if (s2mps11->ext_control_gpiod[rdev_get_id(rdev)])
 			val = S2MPS14_ENABLE_EXT_CONTROL;
 		else
 			val = rdev->desc->enable_mask;
@@ -805,7 +804,7 @@ static int s2mps14_pmic_enable_ext_control(struct s2mps11_info *s2mps11,
 static void s2mps14_pmic_dt_parse_ext_control_gpio(struct platform_device *pdev,
 		struct of_regulator_match *rdata, struct s2mps11_info *s2mps11)
 {
-	int *gpio = s2mps11->ext_control_gpio;
+	struct gpio_desc **gpio = s2mps11->ext_control_gpiod;
 	unsigned int i;
 	unsigned int valid_regulators[3] = { S2MPS14_LDO10, S2MPS14_LDO11,
 		S2MPS14_LDO12 };
@@ -816,11 +815,20 @@ static void s2mps14_pmic_dt_parse_ext_control_gpio(struct platform_device *pdev,
 		if (!rdata[reg].init_data || !rdata[reg].of_node)
 			continue;
 
-		gpio[reg] = of_get_named_gpio(rdata[reg].of_node,
-				"samsung,ext-control-gpios", 0);
-		if (gpio_is_valid(gpio[reg]))
-			dev_dbg(&pdev->dev, "Using GPIO %d for ext-control over %d/%s\n",
-					gpio[reg], reg, rdata[reg].name);
+		gpio[reg] = devm_gpiod_get_from_of_node(&pdev->dev,
+				rdata[reg].of_node,
+				"samsung,ext-control-gpios",
+				0,
+				GPIOD_OUT_HIGH | GPIOD_FLAGS_BIT_NONEXCLUSIVE,
+				"s2mps11-regulator");
+		if (IS_ERR(gpio[reg])) {
+			dev_err(&pdev->dev, "Failed to get control GPIO for %d/%s\n",
+				reg, rdata[reg].name);
+			continue;
+		}
+		if (gpio[reg])
+			dev_dbg(&pdev->dev, "Using GPIO for ext-control over %d/%s\n",
+				reg, rdata[reg].name);
 	}
 }
 
@@ -1126,17 +1134,10 @@ static int s2mps11_pmic_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	s2mps11->ext_control_gpio = devm_kmalloc_array(&pdev->dev,
-			rdev_num, sizeof(*s2mps11->ext_control_gpio),
-			GFP_KERNEL);
-	if (!s2mps11->ext_control_gpio)
+	s2mps11->ext_control_gpiod = devm_kcalloc(&pdev->dev, rdev_num,
+			       sizeof(*s2mps11->ext_control_gpiod), GFP_KERNEL);
+	if (!s2mps11->ext_control_gpiod)
 		return -ENOMEM;
-	/*
-	 * 0 is a valid GPIO so initialize all GPIO-s to negative value
-	 * to indicate that external control won't be used for this regulator.
-	 */
-	for (i = 0; i < rdev_num; i++)
-		s2mps11->ext_control_gpio[i] = -EINVAL;
 
 	if (!iodev->dev->of_node) {
 		if (iodev->pdata) {
@@ -1166,8 +1167,6 @@ static int s2mps11_pmic_probe(struct platform_device *pdev)
 	config.dev = &pdev->dev;
 	config.regmap = iodev->regmap_pmic;
 	config.driver_data = s2mps11;
-	config.ena_gpio_flags = GPIOF_OUT_INIT_HIGH;
-	config.ena_gpio_initialized = true;
 	for (i = 0; i < rdev_num; i++) {
 		struct regulator_dev *regulator;
 
@@ -1178,8 +1177,13 @@ static int s2mps11_pmic_probe(struct platform_device *pdev)
 			config.init_data = rdata[i].init_data;
 			config.of_node = rdata[i].of_node;
 		}
-		config.ena_gpio = s2mps11->ext_control_gpio[i];
-
+		config.ena_gpiod = s2mps11->ext_control_gpiod[i];
+		/*
+		 * Hand the GPIO descriptor management over to the regulator
+		 * core, remove it from devres management.
+		 */
+		if (config.ena_gpiod)
+			devm_gpiod_unhinge(&pdev->dev, config.ena_gpiod);
 		regulator = devm_regulator_register(&pdev->dev,
 						&regulators[i], &config);
 		if (IS_ERR(regulator)) {
@@ -1189,7 +1193,7 @@ static int s2mps11_pmic_probe(struct platform_device *pdev)
 			goto out;
 		}
 
-		if (gpio_is_valid(s2mps11->ext_control_gpio[i])) {
+		if (s2mps11->ext_control_gpiod[i]) {
 			ret = s2mps14_pmic_enable_ext_control(s2mps11,
 					regulator);
 			if (ret < 0) {