Commit 7a05a2cb authored by Ben Dooks's avatar Ben Dooks

[ARM] S3C24XX: GPIO: Change usb-simtec.c to use gpiolib.

Make arch/arm/mach-s3c2410/usb-simtec.c use gpiolib to
manage gpio access.
Signed-off-by: default avatarBen Dooks <ben-linux@fluff.org>
parent 5233c178
......@@ -594,8 +594,6 @@ static void __init bast_map_io(void)
s3c24xx_init_io(bast_iodesc, ARRAY_SIZE(bast_iodesc));
s3c24xx_init_clocks(0);
s3c24xx_init_uarts(bast_uartcfgs, ARRAY_SIZE(bast_uartcfgs));
usb_simtec_init();
}
static void __init bast_init(void)
......@@ -609,6 +607,7 @@ static void __init bast_init(void)
i2c_register_board_info(0, bast_i2c_devs,
ARRAY_SIZE(bast_i2c_devs));
usb_simtec_init();
nor_simtec_init();
}
......
......@@ -22,6 +22,7 @@
#include <linux/timer.h>
#include <linux/init.h>
#include <linux/device.h>
#include <linux/gpio.h>
#include <linux/io.h>
#include <asm/mach/arch.h>
......@@ -30,7 +31,6 @@
#include <mach/bast-map.h>
#include <mach/bast-irq.h>
#include <mach/regs-gpio.h>
#include <mach/hardware.h>
#include <asm/irq.h>
......@@ -54,9 +54,9 @@ usb_simtec_powercontrol(int port, int to)
power_state[port] = to;
if (power_state[0] && power_state[1])
s3c2410_gpio_setpin(S3C2410_GPB(4), 0);
gpio_set_value(S3C2410_GPB(4), 0);
else
s3c2410_gpio_setpin(S3C2410_GPB(4), 1);
gpio_set_value(S3C2410_GPB(4), 1);
}
static irqreturn_t
......@@ -64,7 +64,7 @@ usb_simtec_ocirq(int irq, void *pw)
{
struct s3c2410_hcd_info *info = pw;
if (s3c2410_gpio_getpin(S3C2410_GPG(10)) == 0) {
if (gpio_get_value(S3C2410_GPG(10)) == 0) {
pr_debug("usb_simtec: over-current irq (oc detected)\n");
s3c2410_usb_report_oc(info, 3);
} else {
......@@ -107,10 +107,27 @@ static struct s3c2410_hcd_info usb_simtec_info = {
int usb_simtec_init(void)
{
int ret;
printk("USB Power Control, (c) 2004 Simtec Electronics\n");
s3c_device_usb.dev.platform_data = &usb_simtec_info;
s3c2410_gpio_cfgpin(S3C2410_GPB(4), S3C2410_GPIO_OUTPUT);
s3c2410_gpio_setpin(S3C2410_GPB(4), 1);
ret = gpio_request(S3C2410_GPB(4), "USB power control");
if (ret < 0) {
pr_err("%s: failed to get GPB4\n", __func__);
return ret;
}
ret = gpio_request(S3C2410_GPG(10), "USB overcurrent");
if (ret < 0) {
pr_err("%s: failed to get GPG10\n", __func__);
gpio_free(S3C2410_GPB(4));
return ret;
}
/* turn power on */
gpio_direction_output(S3C2410_GPB(4), 1);
gpio_direction_input(S3C2410_GPG(10));
s3c_device_usb.dev.platform_data = &usb_simtec_info;
return 0;
}
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment