[SCSI] qla4xxx: Add read/update NVRAM support for 40xx adapters using BSG

Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

drivers/scsi/qla4xxx/ql4_bsg.c

@@ -196,6 +196,147 @@ qla4xxx_get_acb_state(struct bsg_job *bsg_job)
 	return rval;
 }
 
+static int
+qla4xxx_read_nvram(struct bsg_job *bsg_job)
+{
+	struct Scsi_Host *host = iscsi_job_to_shost(bsg_job);
+	struct scsi_qla_host *ha = to_qla_host(host);
+	struct iscsi_bsg_request *bsg_req = bsg_job->request;
+	struct iscsi_bsg_reply *bsg_reply = bsg_job->reply;
+	uint32_t offset = 0;
+	uint32_t len = 0;
+	uint32_t total_len = 0;
+	dma_addr_t nvram_dma;
+	uint8_t *nvram = NULL;
+	int rval = -EINVAL;
+
+	bsg_reply->reply_payload_rcv_len = 0;
+
+	if (unlikely(pci_channel_offline(ha->pdev)))
+		goto leave;
+
+	/* Only 40xx adapters are supported */
+	if (!(is_qla4010(ha) || is_qla4022(ha) || is_qla4032(ha)))
+		goto leave;
+
+	if (ql4xxx_reset_active(ha)) {
+		ql4_printk(KERN_ERR, ha, "%s: reset active\n", __func__);
+		rval = -EBUSY;
+		goto leave;
+	}
+
+	offset = bsg_req->rqst_data.h_vendor.vendor_cmd[1];
+	len = bsg_job->reply_payload.payload_len;
+	total_len = offset + len;
+
+	/* total len should not be greater than max NVRAM size */
+	if ((is_qla4010(ha) && total_len > QL4010_NVRAM_SIZE) ||
+	    ((is_qla4022(ha) || is_qla4032(ha)) &&
+	     total_len > QL40X2_NVRAM_SIZE)) {
+		ql4_printk(KERN_ERR, ha, "%s: offset+len greater than max"
+			   " nvram size, offset=%d len=%d\n",
+			   __func__, offset, len);
+		goto leave;
+	}
+
+	nvram = dma_alloc_coherent(&ha->pdev->dev, len, &nvram_dma,
+				   GFP_KERNEL);
+	if (!nvram) {
+		ql4_printk(KERN_ERR, ha, "%s: dma alloc failed for nvram "
+			   "data\n", __func__);
+		rval = -ENOMEM;
+		goto leave;
+	}
+
+	rval = qla4xxx_get_nvram(ha, nvram_dma, offset, len);
+	if (rval) {
+		ql4_printk(KERN_ERR, ha, "%s: get nvram failed\n", __func__);
+		bsg_reply->result = DID_ERROR << 16;
+		rval = -EIO;
+	} else {
+		bsg_reply->reply_payload_rcv_len =
+			sg_copy_from_buffer(bsg_job->reply_payload.sg_list,
+					    bsg_job->reply_payload.sg_cnt,
+					    nvram, len);
+		bsg_reply->result = DID_OK << 16;
+	}
+
+	bsg_job_done(bsg_job, bsg_reply->result,
+		     bsg_reply->reply_payload_rcv_len);
+	dma_free_coherent(&ha->pdev->dev, len, nvram, nvram_dma);
+leave:
+	return rval;
+}
+
+static int
+qla4xxx_update_nvram(struct bsg_job *bsg_job)
+{
+	struct Scsi_Host *host = iscsi_job_to_shost(bsg_job);
+	struct scsi_qla_host *ha = to_qla_host(host);
+	struct iscsi_bsg_request *bsg_req = bsg_job->request;
+	struct iscsi_bsg_reply *bsg_reply = bsg_job->reply;
+	uint32_t offset = 0;
+	uint32_t len = 0;
+	uint32_t total_len = 0;
+	dma_addr_t nvram_dma;
+	uint8_t *nvram = NULL;
+	int rval = -EINVAL;
+
+	bsg_reply->reply_payload_rcv_len = 0;
+
+	if (unlikely(pci_channel_offline(ha->pdev)))
+		goto leave;
+
+	if (!(is_qla4010(ha) || is_qla4022(ha) || is_qla4032(ha)))
+		goto leave;
+
+	if (ql4xxx_reset_active(ha)) {
+		ql4_printk(KERN_ERR, ha, "%s: reset active\n", __func__);
+		rval = -EBUSY;
+		goto leave;
+	}
+
+	offset = bsg_req->rqst_data.h_vendor.vendor_cmd[1];
+	len = bsg_job->request_payload.payload_len;
+	total_len = offset + len;
+
+	/* total len should not be greater than max NVRAM size */
+	if ((is_qla4010(ha) && total_len > QL4010_NVRAM_SIZE) ||
+	    ((is_qla4022(ha) || is_qla4032(ha)) &&
+	     total_len > QL40X2_NVRAM_SIZE)) {
+		ql4_printk(KERN_ERR, ha, "%s: offset+len greater than max"
+			   " nvram size, offset=%d len=%d\n",
+			   __func__, offset, len);
+		goto leave;
+	}
+
+	nvram = dma_alloc_coherent(&ha->pdev->dev, len, &nvram_dma,
+				   GFP_KERNEL);
+	if (!nvram) {
+		ql4_printk(KERN_ERR, ha, "%s: dma alloc failed for flash "
+			   "data\n", __func__);
+		rval = -ENOMEM;
+		goto leave;
+	}
+
+	sg_copy_to_buffer(bsg_job->request_payload.sg_list,
+			  bsg_job->request_payload.sg_cnt, nvram, len);
+
+	rval = qla4xxx_set_nvram(ha, nvram_dma, offset, len);
+	if (rval) {
+		ql4_printk(KERN_ERR, ha, "%s: set nvram failed\n", __func__);
+		bsg_reply->result = DID_ERROR << 16;
+		rval = -EIO;
+	} else
+		bsg_reply->result = DID_OK << 16;
+
+	bsg_job_done(bsg_job, bsg_reply->result,
+		     bsg_reply->reply_payload_rcv_len);
+	dma_free_coherent(&ha->pdev->dev, len, nvram, nvram_dma);
+leave:
+	return rval;
+}
+
 /**
  * qla4xxx_process_vendor_specific - handle vendor specific bsg request
  * @job: iscsi_bsg_job to handle
@@ -217,6 +358,12 @@ int qla4xxx_process_vendor_specific(struct bsg_job *bsg_job)
 	case QLISCSI_VND_GET_ACB_STATE:
 		return qla4xxx_get_acb_state(bsg_job);
 
+	case QLISCSI_VND_READ_NVRAM:
+		return qla4xxx_read_nvram(bsg_job);
+
+	case QLISCSI_VND_UPDATE_NVRAM:
+		return qla4xxx_update_nvram(bsg_job);
+
 	default:
 		ql4_printk(KERN_ERR, ha, "%s: invalid BSG vendor command: "
 			   "0x%x\n", __func__, bsg_req->msgcode);

drivers/scsi/qla4xxx/ql4_bsg.h

@@ -11,5 +11,7 @@
 #define QLISCSI_VND_READ_FLASH		1
 #define QLISCSI_VND_UPDATE_FLASH	2
 #define QLISCSI_VND_GET_ACB_STATE	3
+#define QLISCSI_VND_READ_NVRAM		4
+#define QLISCSI_VND_UPDATE_NVRAM	5
 
 #endif

drivers/scsi/qla4xxx/ql4_fw.h

@@ -201,6 +201,9 @@ static inline uint32_t clr_rmask(uint32_t val)
 /* ISP 4022 nvram definitions */
 #define NVR_WRITE_ENABLE			0x00000010	/* 4022 */
 
+#define QL4010_NVRAM_SIZE			0x200
+#define QL40X2_NVRAM_SIZE			0x800
+
 /*  ISP port_status definitions */
 
 /*  ISP Semaphore definitions */
@@ -359,6 +362,8 @@ struct qla_flt_region {
 #define MBOX_CMD_GET_FW_STATE			0x0069
 #define MBOX_CMD_GET_INIT_FW_CTRL_BLOCK_DEFAULTS 0x006A
 #define MBOX_CMD_GET_SYS_INFO			0x0078
+#define MBOX_CMD_GET_NVRAM			0x0078	/* For 40xx */
+#define MBOX_CMD_SET_NVRAM			0x0079	/* For 40xx */
 #define MBOX_CMD_RESTORE_FACTORY_DEFAULTS	0x0087
 #define MBOX_CMD_SET_ACB			0x0088
 #define MBOX_CMD_GET_ACB			0x0089

drivers/scsi/qla4xxx/ql4_glbl.h

@@ -162,6 +162,10 @@ int qla4xxx_bootdb_by_index(struct scsi_qla_host *ha,
 			    dma_addr_t fw_ddb_entry_dma, uint16_t ddb_index);
 int qla4xxx_get_chap(struct scsi_qla_host *ha, char *username,
 		     char *password, uint16_t idx);
+int qla4xxx_get_nvram(struct scsi_qla_host *ha, dma_addr_t nvram_dma,
+		      uint32_t offset, uint32_t size);
+int qla4xxx_set_nvram(struct scsi_qla_host *ha, dma_addr_t nvram_dma,
+		      uint32_t offset, uint32_t size);
 
 /* BSG Functions */
 int qla4xxx_bsg_request(struct bsg_job *bsg_job);

drivers/scsi/qla4xxx/ql4_mbx.c

@@ -1690,3 +1690,55 @@ int qla4xxx_get_ip_state(struct scsi_qla_host *ha, uint32_t acb_idx,
 	memcpy(sts, mbox_sts, sizeof(mbox_sts));
 	return status;
 }
+
+int qla4xxx_get_nvram(struct scsi_qla_host *ha, dma_addr_t nvram_dma,
+		      uint32_t offset, uint32_t size)
+{
+	int status = QLA_SUCCESS;
+	uint32_t mbox_cmd[MBOX_REG_COUNT];
+	uint32_t mbox_sts[MBOX_REG_COUNT];
+
+	memset(&mbox_cmd, 0, sizeof(mbox_cmd));
+	memset(&mbox_sts, 0, sizeof(mbox_sts));
+
+	mbox_cmd[0] = MBOX_CMD_GET_NVRAM;
+	mbox_cmd[1] = LSDW(nvram_dma);
+	mbox_cmd[2] = MSDW(nvram_dma);
+	mbox_cmd[3] = offset;
+	mbox_cmd[4] = size;
+
+	status = qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 1, &mbox_cmd[0],
+					 &mbox_sts[0]);
+	if (status != QLA_SUCCESS) {
+		DEBUG2(ql4_printk(KERN_ERR, ha, "scsi%ld: %s: failed "
+				  "status %04X\n", ha->host_no, __func__,
+				  mbox_sts[0]));
+	}
+	return status;
+}
+
+int qla4xxx_set_nvram(struct scsi_qla_host *ha, dma_addr_t nvram_dma,
+		      uint32_t offset, uint32_t size)
+{
+	int status = QLA_SUCCESS;
+	uint32_t mbox_cmd[MBOX_REG_COUNT];
+	uint32_t mbox_sts[MBOX_REG_COUNT];
+
+	memset(&mbox_cmd, 0, sizeof(mbox_cmd));
+	memset(&mbox_sts, 0, sizeof(mbox_sts));
+
+	mbox_cmd[0] = MBOX_CMD_SET_NVRAM;
+	mbox_cmd[1] = LSDW(nvram_dma);
+	mbox_cmd[2] = MSDW(nvram_dma);
+	mbox_cmd[3] = offset;
+	mbox_cmd[4] = size;
+
+	status = qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 1, &mbox_cmd[0],
+					 &mbox_sts[0]);
+	if (status != QLA_SUCCESS) {
+		DEBUG2(ql4_printk(KERN_ERR, ha, "scsi%ld: %s: failed "
+				  "status %04X\n", ha->host_no, __func__,
+				  mbox_sts[0]));
+	}
+	return status;
+}