ARM: dts: imx51: Fix USB PHY duplicate unit-address

Currently the following DTC warnings are seen with W=1:

arch/arm/boot/dts/imx51-babbage.dtb: Warning (unique_unit_address): /usbphy/usbphy@0: duplicate unit-address (also used in node /usbphy/usbh1phy@0)
arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dtb: Warning (unique_unit_address): /usbphy/usbphy@0: duplicate unit-address (also used in node /usbphy/usbh1phy@0)

Fix it by moving the USB PHY nodes outside of simple-bus and drop the
unneeded unit-address, which matches the bindings documentation
at Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt

While at it rename the USB PHY node to usbphy1 for consistency.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arch/arm/boot/dts/imx51-babbage.dts

@@ -170,22 +170,15 @@ sound {
 		mux-ext-port = <3>;
 	};
 
-	usbphy {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "simple-bus";
-
-		usbh1phy: usbh1phy@0 {
-			compatible = "usb-nop-xceiv";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_usbh1reg>;
-			reg = <0>;
-			clocks = <&clk_usb>;
-			clock-names = "main_clk";
-			reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
-			vcc-supply = <&vusb_reg>;
-			#phy-cells = <0>;
-		};
+	usbphy1: usbphy1 {
+		compatible = "usb-nop-xceiv";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1reg>;
+		clocks = <&clk_usb>;
+		clock-names = "main_clk";
+		reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
+		vcc-supply = <&vusb_reg>;
+		#phy-cells = <0>;
 	};
 };
 
@@ -431,7 +424,7 @@ &usbh1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbh1>;
 	vbus-supply = <&reg_hub_reset>;
-	fsl,usbphy = <&usbh1phy>;
+	fsl,usbphy = <&usbphy1>;
 	phy_type = "ulpi";
 	status = "okay";
 };

arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts

@@ -83,19 +83,12 @@ sound {
 		fsl,mux-ext-port = <3>;
 	};
 
-	usbphy {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "simple-bus";
-
-		usbh1phy: usbh1phy@0 {
-			compatible = "usb-nop-xceiv";
-			reg = <0>;
-			clocks = <&clks IMX5_CLK_USB_PHY_GATE>;
-			clock-names = "main_clk";
-			clock-frequency = <19200000>;
-			#phy-cells = <0>;
-		};
+	usbphy1: usbphy1 {
+		compatible = "usb-nop-xceiv";
+		clocks = <&clks IMX5_CLK_USB_PHY_GATE>;
+		clock-names = "main_clk";
+		clock-frequency = <19200000>;
+		#phy-cells = <0>;
 	};
 };
 
@@ -275,7 +268,7 @@ &uart3 {
 &usbh1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbh1>;
-	fsl,usbphy = <&usbh1phy>;
+	fsl,usbphy = <&usbphy1>;
 	dr_mode = "host";
 	phy_type = "ulpi";
 	status = "okay";

arch/arm/boot/dts/imx51.dtsi

@@ -93,18 +93,11 @@ cpu: cpu@0 {
 		};
 	};
 
-	usbphy {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "simple-bus";
-
-		usbphy0: usbphy@0 {
-			compatible = "usb-nop-xceiv";
-			reg = <0>;
-			clocks = <&clks IMX5_CLK_USB_PHY_GATE>;
-			clock-names = "main_clk";
-			#phy-cells = <0>;
-		};
+	usbphy0: usbphy0 {
+		compatible = "usb-nop-xceiv";
+		clocks = <&clks IMX5_CLK_USB_PHY_GATE>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
 	};
 
 	display-subsystem {