ide: remove SATA_*_REG macros

* siimage.c: use hwif->sata_scr[SATA_{ERROR,STATUS}_OFFSET] instead of
  SATA_{ERROR,STATUS}_REG macros.

* Remove no longer needed SATA_*_REG macros.

While at it:

* Remove needless SATA Status register read from sil_sata_reset_poll().
Signed-off-by: default avatarBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
parent 92b83c8f
......@@ -331,15 +331,18 @@ static int siimage_mmio_ide_dma_test_irq (ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long addr = siimage_selreg(hwif, 0x1);
void __iomem *sata_error_addr
= (void __iomem *)hwif->sata_scr[SATA_ERROR_OFFSET];
if (SATA_ERROR_REG) {
if (sata_error_addr) {
unsigned long base = (unsigned long)hwif->hwif_data;
u32 ext_stat = readl((void __iomem *)(base + 0x10));
u8 watchdog = 0;
if (ext_stat & ((hwif->channel) ? 0x40 : 0x10)) {
u32 sata_error = readl((void __iomem *)SATA_ERROR_REG);
writel(sata_error, (void __iomem *)SATA_ERROR_REG);
u32 sata_error = readl(sata_error_addr);
writel(sata_error, sata_error_addr);
watchdog = (sata_error & 0x00680000) ? 1 : 0;
printk(KERN_WARNING "%s: sata_error = 0x%08x, "
"watchdog = %d, %s\n",
......@@ -418,13 +421,17 @@ static int sil_sata_busproc(ide_drive_t * drive, int state)
static int sil_sata_reset_poll(ide_drive_t *drive)
{
if (SATA_STATUS_REG) {
ide_hwif_t *hwif = HWIF(drive);
ide_hwif_t *hwif = drive->hwif;
void __iomem *sata_status_addr
= (void __iomem *)hwif->sata_scr[SATA_STATUS_OFFSET];
if (sata_status_addr) {
/* SATA Status is available only when in MMIO mode */
u32 sata_stat = readl(sata_status_addr);
/* SATA_STATUS_REG is valid only when in MMIO mode */
if ((readl((void __iomem *)SATA_STATUS_REG) & 0x03) != 0x03) {
if ((sata_stat & 0x03) != 0x03) {
printk(KERN_WARNING "%s: reset phy dead, status=0x%08x\n",
hwif->name, readl((void __iomem *)SATA_STATUS_REG));
hwif->name, sata_stat);
HWGROUP(drive)->polling = 0;
return ide_started;
}
......
......@@ -112,18 +112,12 @@ typedef unsigned char byte; /* used everywhere */
#define SATA_NR_PORTS (3) /* 16 possible ?? */
#define SATA_STATUS_OFFSET (0)
#define SATA_STATUS_REG (HWIF(drive)->sata_scr[SATA_STATUS_OFFSET])
#define SATA_ERROR_OFFSET (1)
#define SATA_ERROR_REG (HWIF(drive)->sata_scr[SATA_ERROR_OFFSET])
#define SATA_CONTROL_OFFSET (2)
#define SATA_CONTROL_REG (HWIF(drive)->sata_scr[SATA_CONTROL_OFFSET])
#define SATA_MISC_OFFSET (0)
#define SATA_MISC_REG (HWIF(drive)->sata_misc[SATA_MISC_OFFSET])
#define SATA_PHY_OFFSET (1)
#define SATA_PHY_REG (HWIF(drive)->sata_misc[SATA_PHY_OFFSET])
#define SATA_IEN_OFFSET (2)
#define SATA_IEN_REG (HWIF(drive)->sata_misc[SATA_IEN_OFFSET])
/*
* Our Physical Region Descriptor (PRD) table should be large enough
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment