Merge flatcap.org:/home/flatcap/backup/bk/ntfs-2.6

into flatcap.org:/home/flatcap/backup/bk/ntfs-2.6-devel

arch/alpha/kernel/sys_dp264.c

@@ -71,10 +71,10 @@ tsunami_update_irq_hw(unsigned long mask)
 	dim1 = &cchip->dim1.csr;
 	dim2 = &cchip->dim2.csr;
 	dim3 = &cchip->dim3.csr;
-	if (cpu_possible(0)) dim0 = &dummy;
-	if (cpu_possible(1)) dim1 = &dummy;
-	if (cpu_possible(2)) dim2 = &dummy;
-	if (cpu_possible(3)) dim3 = &dummy;
+	if (!cpu_possible(0)) dim0 = &dummy;
+	if (!cpu_possible(1)) dim1 = &dummy;
+	if (!cpu_possible(2)) dim2 = &dummy;
+	if (!cpu_possible(3)) dim3 = &dummy;
 
 	*dim0 = mask0;
 	*dim1 = mask1;

arch/arm/Kconfig

@@ -167,6 +167,11 @@ config ARCH_VERSATILE_PB
 config ARCH_IMX
 	bool "IMX"
 
+config ARCH_H720X
+	bool "Hynix-HMS720x-based"
+	help
+	  This enables support for systems based on the Hynix HMS720x
+
 endchoice
 
 source "arch/arm/mach-clps711x/Kconfig"
@@ -195,6 +200,8 @@ source "arch/arm/mach-lh7a40x/Kconfig"
 
 source "arch/arm/mach-imx/Kconfig"
 
+source "arch/arm/mach-h720x/Kconfig"
+
 # Definitions to make life easier
 config ARCH_ACORN
 	bool

arch/arm/Makefile

@@ -95,6 +95,7 @@ textaddr-$(CONFIG_ARCH_FORTUNET)   := 0xc0008000
  machine-$(CONFIG_ARCH_LH7A40X)	   := lh7a40x
  machine-$(CONFIG_ARCH_VERSATILE_PB) := versatile
  machine-$(CONFIG_ARCH_IMX)	   := imx
+ machine-$(CONFIG_ARCH_H720X)	   := h720x
 
 ifeq ($(CONFIG_ARCH_EBSA110),y)
 # This is what happens if you forget the IOCS16 line.

arch/arm/boot/Makefile

@@ -71,6 +71,7 @@ params_phys-$(CONFIG_ARCH_S3C2410)	:= 0x30000100
    zreladdr-$(CONFIG_ARCH_VERSATILE_PB)	:= 0x00008000
 params_phys-$(CONFIG_ARCH_VERSATILE_PB)	:= 0x00000100
 initrd_phys-$(CONFIG_ARCH_VERSATILE_PB)	:= 0x00800000
+   zreladdr-$(CONFIG_ARCH_H720X)	:= 0x40008000
 
 ZRELADDR    := $(zreladdr-y)
 PARAMS_PHYS := $(params_phys-y)

arch/arm/configs/h7201_defconfig

+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.9-rc1
+# Thu Sep  2 11:04:11 2004
+#
+CONFIG_ARM=y
+CONFIG_MMU=y
+CONFIG_UID16=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_CLEAN_COMPILE=y
+CONFIG_BROKEN_ON_SMP=y
+
+#
+# General setup
+#
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+CONFIG_SYSCTL=y
+# CONFIG_AUDIT is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_HOTPLUG=y
+# CONFIG_IKCONFIG is not set
+# CONFIG_EMBEDDED is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+# CONFIG_MODULE_UNLOAD is not set
+CONFIG_OBSOLETE_MODPARM=y
+# CONFIG_MODVERSIONS is not set
+CONFIG_KMOD=y
+
+#
+# System Type
+#
+# CONFIG_ARCH_CLPS7500 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_CO285 is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_CAMELOT is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_IOP3XX is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_OMAP is not set
+# CONFIG_ARCH_VERSATILE_PB is not set
+# CONFIG_ARCH_IMX is not set
+CONFIG_ARCH_H720X=y
+
+#
+# h720x Implementations
+#
+CONFIG_ARCH_H7201=y
+# CONFIG_ARCH_H7202 is not set
+CONFIG_CPU_H7201=y
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_ARM720T=y
+CONFIG_CPU_32v4=y
+CONFIG_CPU_ABRT_LV4T=y
+CONFIG_CPU_CACHE_V4=y
+CONFIG_CPU_COPY_V4WT=y
+CONFIG_CPU_TLB_V4WT=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+
+#
+# General setup
+#
+# CONFIG_ZBOOT_ROM is not set
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+
+#
+# PCMCIA/CardBus support
+#
+CONFIG_PCMCIA=y
+# CONFIG_PCMCIA_DEBUG is not set
+# CONFIG_TCIC is not set
+
+#
+# At least one math emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+# CONFIG_VFP is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_PM is not set
+# CONFIG_PREEMPT is not set
+# CONFIG_ARTHUR is not set
+CONFIG_CMDLINE=""
+CONFIG_ALIGNMENT_TRAP=y
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+CONFIG_MTD=y
+CONFIG_MTD_DEBUG=y
+CONFIG_MTD_DEBUG_VERBOSE=0
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_NOSWAP=y
+# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
+# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
+# CONFIG_MTD_CFI_GEOMETRY is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_CFI_INTELEXT=y
+# CONFIG_MTD_CFI_AMDSTD is not set
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_ARM_INTEGRATOR is not set
+# CONFIG_MTD_EDB7312 is not set
+# CONFIG_MTD_H720X is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLKMTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+
+#
+# NAND Flash Device Drivers
+#
+# CONFIG_MTD_NAND is not set
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_LOOP is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_BLK_DEV_INITRD=y
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Networking support
+#
+# CONFIG_NET is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# SCSI device support
+#
+# CONFIG_SCSI is not set
+
+#
+# Fusion MPT device support
+#
+
+#
+# IEEE 1394 (FireWire) support
+#
+
+#
+# I2O device support
+#
+
+#
+# ISDN subsystem
+#
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_TSDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input I/O drivers
+#
+# CONFIG_GAMEPORT is not set
+CONFIG_SOUND_GAMEPORT=y
+CONFIG_SERIO=y
+# CONFIG_SERIO_I8042 is not set
+CONFIG_SERIO_SERPORT=y
+# CONFIG_SERIO_CT82C710 is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_QIC02_TAPE is not set
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_NVRAM is not set
+# CONFIG_RTC is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+
+#
+# Ftape, the floppy tape device driver
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+
+#
+# PCMCIA character devices
+#
+# CONFIG_SYNCLINK_CS is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# I2C support
+#
+# CONFIG_I2C is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_JBD is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_SYSFS=y
+# CONFIG_DEVFS_FS is not set
+# CONFIG_DEVPTS_FS_XATTR is not set
+# CONFIG_TMPFS is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+# CONFIG_JFFS2_FS_NAND is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+
+#
+# Profiling support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Graphics support
+#
+# CONFIG_FB is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+# CONFIG_MDA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+
+#
+# Sound
+#
+CONFIG_SOUND=m
+
+#
+# Advanced Linux Sound Architecture
+#
+# CONFIG_SND is not set
+
+#
+# Open Sound System
+#
+# CONFIG_SOUND_PRIME is not set
+
+#
+# Misc devices
+#
+
+#
+# USB support
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_DEBUG_KERNEL is not set
+# CONFIG_DEBUG_INFO is not set
+CONFIG_FRAME_POINTER=y
+CONFIG_DEBUG_USER=y
+
+#
+# Security options
+#
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y

arch/arm/kernel/debug.S

@@ -675,6 +675,36 @@
 		tst	\rd, #1 << 3		@ TXDC
 		beq	1002b			@ wait until transmit done
 		.endm
+
+#elif defined(CONFIG_ARCH_H720X)
+
+		.equ    io_virt, IO_BASE
+		.equ    io_phys, IO_START
+
+		.macro  addruart,rx
+		mrc     p15, 0, \rx, c1, c0
+		tst     \rx, #1  	       @ MMU enabled?
+		moveq   \rx, #io_phys	       @ physical base address
+		movne   \rx, #io_virt	       @ virtual address
+		add     \rx, \rx, #0x00020000   @ UART1
+		.endm
+
+		.macro  senduart,rd,rx
+		str     \rd, [\rx, #0x0]        @ UARTDR
+
+		.endm
+
+		.macro  waituart,rd,rx
+1001:		ldr     \rd, [\rx, #0x18]       @ UARTFLG
+		tst     \rd, #1 << 5	       @ UARTFLGUTXFF - 1 when full
+		bne     1001b
+		.endm
+
+		.macro  busyuart,rd,rx
+1001:		ldr     \rd, [\rx, #0x18]       @ UARTFLG
+		tst     \rd, #1 << 3	       @ UARTFLGUBUSY - 1 when busy
+		bne     1001b
+		.endm
 #else
 #error Unknown architecture
 #endif

arch/arm/kernel/entry-armv.S

@@ -962,6 +962,57 @@ ENTRY(soft_irq_mask)
 		.macro	irq_prio_table
 		.endm
 
+#elif defined(CONFIG_ARCH_H720X)
+
+		.macro  disable_fiq
+		.endm
+
+		.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
+#if defined (CONFIG_CPU_H7201) || defined (CONFIG_CPU_H7202)
+		@ we could use the id register on H7202, but this is not
+		@ properly updated when we come back from asm_do_irq
+		@ without a previous return from interrupt
+		@ (see loops below in irq_svc, irq_usr)
+		@ We see unmasked pending ints only, as the masked pending ints
+		@ are not visible here
+
+		mov     \base, #0xf0000000	       @ base register
+		orr     \base, \base, #0x24000	       @ irqbase
+		ldr     \irqstat, [\base, #0x04]        @ get interrupt status
+#if defined (CONFIG_CPU_H7201)
+		ldr	\tmp, =0x001fffff
+#else
+		mvn     \tmp, #0xc0000000
+#endif
+		and     \irqstat, \irqstat, \tmp        @ mask out unused ints
+		mov     \irqnr, #0
+
+		mov     \tmp, #0xff00
+		orr     \tmp, \tmp, #0xff
+		tst     \irqstat, \tmp
+		addeq   \irqnr, \irqnr, #16
+		moveq   \irqstat, \irqstat, lsr #16
+		tst     \irqstat, #255
+		addeq   \irqnr, \irqnr, #8
+		moveq   \irqstat, \irqstat, lsr #8
+		tst     \irqstat, #15
+		addeq   \irqnr, \irqnr, #4
+		moveq   \irqstat, \irqstat, lsr #4
+		tst     \irqstat, #3
+		addeq   \irqnr, \irqnr, #2
+		moveq   \irqstat, \irqstat, lsr #2
+		tst     \irqstat, #1
+		addeq   \irqnr, \irqnr, #1
+		moveq   \irqstat, \irqstat, lsr #1
+		tst     \irqstat, #1		       @ bit 0 should be set
+		.endm
+
+		.macro  irq_prio_table
+		.endm
+
+#else
+#error hynix processor selection missmatch
+#endif
 #else
 #error Unknown architecture
 #endif

arch/arm/mach-h720x/Kconfig

+menu "h720x Implementations"
+
+config ARCH_H7201
+	bool "gms30c7201"
+	depends on ARCH_H720X
+	select CPU_H7201
+	help
+	  Say Y here if you are using the Hynix GMS30C7201 Reference Board
+
+config ARCH_H7202
+	bool "hms30c7202"
+	select CPU_H7202
+	depends on ARCH_H720X
+	help
+	  Say Y here if you are using the Hynix HMS30C7202 Reference Board
+
+endmenu
+
+config CPU_H7201
+	bool
+	help
+	  Select code specific to h7201 variants
+
+config CPU_H7202
+	bool
+	help
+	  Select code specific to h7202 variants

arch/arm/mach-h720x/Makefile

+#
+# Makefile for the linux kernel.
+#
+
+# Common support
+obj-y := common.o
+obj-m :=
+obj-n :=
+obj-  :=
+
+# Specific board support
+
+obj-$(CONFIG_ARCH_H7201)		+= h7201-eval.o
+obj-$(CONFIG_ARCH_H7202)		+= h7202-eval.o
+obj-$(CONFIG_CPU_H7201) 		+= cpu-h7201.o
+obj-$(CONFIG_CPU_H7202) 		+= cpu-h7202.o

arch/arm/mach-h720x/common.c

+/*
+ * linux/arch/arm/mach-h720x/common.c
+ *
+ * Copyright (C) 2003 Thomas Gleixner <tglx@linutronix.de>
+ *               2003 Robert Schwebel <r.schwebel@pengutronix.de>
+ *               2004 Sascha Hauer    <s.hauer@pengutronix.de>
+ *
+ * common stuff for Hynix h720x processors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/mman.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+
+#include <asm/page.h>
+#include <asm/pgtable.h>
+#include <asm/dma.h>
+#include <asm/io.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/map.h>
+#include <asm/arch/irqs.h>
+
+#include <asm/mach/dma.h>
+
+#if 0
+#define IRQDBG(args...) printk(args)
+#else
+#define IRQDBG(args...) do {} while(0)
+#endif
+
+void __init arch_dma_init(dma_t *dma)
+{
+}
+
+/*
+ * Return usecs since last timer reload
+ * (timercount * (usecs perjiffie)) / (ticks per jiffie)
+ */
+unsigned long h720x_gettimeoffset(void)
+{
+	return (CPU_REG (TIMER_VIRT, TM0_COUNT) * tick_usec) / LATCH;
+}
+
+/*
+ * mask Global irq's
+ */
+static void mask_global_irq (unsigned int irq )
+{
+	CPU_REG (IRQC_VIRT, IRQC_IER) &= ~(1 << irq);
+}
+
+/*
+ * unmask Global irq's
+ */
+static void unmask_global_irq (unsigned int irq )
+{
+	CPU_REG (IRQC_VIRT, IRQC_IER) |= (1 << irq);
+}
+
+
+/*
+ * ack GPIO irq's
+ * Ack only for edge triggered int's valid
+ */
+static void inline ack_gpio_irq(u32 irq)
+{
+	u32 reg_base = GPIO_VIRT(IRQ_TO_REGNO(irq));
+	u32 bit = IRQ_TO_BIT(irq);
+	if ( (CPU_REG (reg_base, GPIO_EDGE) & bit))
+		CPU_REG (reg_base, GPIO_CLR) = bit;
+}
+
+/*
+ * mask GPIO irq's
+ */
+static void inline mask_gpio_irq(u32 irq)
+{
+	u32 reg_base = GPIO_VIRT(IRQ_TO_REGNO(irq));
+	u32 bit = IRQ_TO_BIT(irq);
+	CPU_REG (reg_base, GPIO_MASK) &= ~bit;
+}
+
+/*
+ * unmask GPIO irq's
+ */
+static void inline unmask_gpio_irq(u32 irq)
+{
+	u32 reg_base = GPIO_VIRT(IRQ_TO_REGNO(irq));
+	u32 bit = IRQ_TO_BIT(irq);
+	CPU_REG (reg_base, GPIO_MASK) |= bit;
+}
+
+static void
+h720x_gpio_handler(unsigned int mask, unsigned int irq,
+                 struct irqdesc *desc, struct pt_regs *regs)
+{
+	IRQDBG("%s irq: %d\n",__FUNCTION__,irq);
+	desc = irq_desc + irq;
+	while (mask) {
+		if (mask & 1) {
+			IRQDBG("handling irq %d\n", irq);
+			desc->handle(irq, desc, regs);
+		}
+		irq++;
+		desc++;
+		mask >>= 1;
+	}
+}
+
+static void
+h720x_gpioa_demux_handler(unsigned int irq_unused, struct irqdesc *desc,
+			struct pt_regs *regs)
+{
+	unsigned int mask, irq;
+
+	mask = CPU_REG(GPIO_A_VIRT,GPIO_STAT);
+	irq = IRQ_CHAINED_GPIOA(0);
+	IRQDBG("%s mask: 0x%08x irq: %d\n",__FUNCTION__,mask,irq);
+	h720x_gpio_handler(mask, irq, desc, regs);
+}
+
+static void
+h720x_gpiob_demux_handler(unsigned int irq_unused, struct irqdesc *desc,
+			struct pt_regs *regs)
+{
+	unsigned int mask, irq;
+	mask = CPU_REG(GPIO_B_VIRT,GPIO_STAT);
+	irq = IRQ_CHAINED_GPIOB(0);
+	IRQDBG("%s mask: 0x%08x irq: %d\n",__FUNCTION__,mask,irq);
+	h720x_gpio_handler(mask, irq, desc, regs);
+}
+
+static void
+h720x_gpioc_demux_handler(unsigned int irq_unused, struct irqdesc *desc,
+			struct pt_regs *regs)
+{
+	unsigned int mask, irq;
+
+	mask = CPU_REG(GPIO_C_VIRT,GPIO_STAT);
+	irq = IRQ_CHAINED_GPIOC(0);
+	IRQDBG("%s mask: 0x%08x irq: %d\n",__FUNCTION__,mask,irq);
+	h720x_gpio_handler(mask, irq, desc, regs);
+}
+
+static void
+h720x_gpiod_demux_handler(unsigned int irq_unused, struct irqdesc *desc,
+			struct pt_regs *regs)
+{
+	unsigned int mask, irq;
+
+	mask = CPU_REG(GPIO_D_VIRT,GPIO_STAT);
+	irq = IRQ_CHAINED_GPIOD(0);
+	IRQDBG("%s mask: 0x%08x irq: %d\n",__FUNCTION__,mask,irq);
+	h720x_gpio_handler(mask, irq, desc, regs);
+}
+
+#ifdef CONFIG_CPU_H7202
+static void
+h720x_gpioe_demux_handler(unsigned int irq_unused, struct irqdesc *desc,
+			struct pt_regs *regs)
+{
+	unsigned int mask, irq;
+
+	mask = CPU_REG(GPIO_E_VIRT,GPIO_STAT);
+	irq = IRQ_CHAINED_GPIOE(0);
+	IRQDBG("%s mask: 0x%08x irq: %d\n",__FUNCTION__,mask,irq);
+	h720x_gpio_handler(mask, irq, desc, regs);
+}
+#endif
+
+static struct irqchip h720x_global_chip = {
+	.ack = mask_global_irq,
+	.mask = mask_global_irq,
+	.unmask = unmask_global_irq,
+};
+
+static struct irqchip h720x_gpio_chip = {
+	.ack = ack_gpio_irq,
+	.mask = mask_gpio_irq,
+	.unmask = unmask_gpio_irq,
+};
+
+/*
+ * Initialize IRQ's, mask all, enable multiplexed irq's
+ */
+void __init h720x_init_irq (void)
+{
+	int 	irq;
+
+	/* Mask global irq's */
+	CPU_REG (IRQC_VIRT, IRQC_IER) = 0x0;
+
+	/* Mask all multiplexed irq's */
+	CPU_REG (GPIO_A_VIRT, GPIO_MASK) = 0x0;
+	CPU_REG (GPIO_B_VIRT, GPIO_MASK) = 0x0;
+	CPU_REG (GPIO_C_VIRT, GPIO_MASK) = 0x0;
+	CPU_REG (GPIO_D_VIRT, GPIO_MASK) = 0x0;
+
+	/* Initialize global IRQ's, fast path */
+	for (irq = 0; irq < NR_GLBL_IRQS; irq++) {
+		set_irq_chip(irq, &h720x_global_chip);
+		set_irq_handler(irq, do_level_IRQ);
+		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+	}
+
+	/* Initialize multiplexed IRQ's, slow path */
+	for (irq = IRQ_CHAINED_GPIOA(0) ; irq <= IRQ_CHAINED_GPIOD(31); irq++) {
+		set_irq_chip(irq, &h720x_gpio_chip);
+		set_irq_handler(irq, do_edge_IRQ);
+		set_irq_flags(irq, IRQF_VALID );
+	}
+	set_irq_chained_handler(IRQ_GPIOA, h720x_gpioa_demux_handler);
+	set_irq_chained_handler(IRQ_GPIOB, h720x_gpiob_demux_handler);
+	set_irq_chained_handler(IRQ_GPIOC, h720x_gpioc_demux_handler);
+	set_irq_chained_handler(IRQ_GPIOD, h720x_gpiod_demux_handler);
+
+#ifdef CONFIG_CPU_H7202
+	for (irq = IRQ_CHAINED_GPIOE(0) ; irq <= IRQ_CHAINED_GPIOE(31); irq++) {
+		set_irq_chip(irq, &h720x_gpio_chip);
+		set_irq_handler(irq, do_edge_IRQ);
+		set_irq_flags(irq, IRQF_VALID );
+	}
+	set_irq_chained_handler(IRQ_GPIOE, h720x_gpioe_demux_handler);
+#endif
+
+	/* Enable multiplexed irq's */
+	CPU_REG (IRQC_VIRT, IRQC_IER) = IRQ_ENA_MUX;
+}
+
+static struct map_desc h720x_io_desc[] __initdata = {
+	{ IO_VIRT, IO_PHYS, IO_SIZE, MT_DEVICE },
+};
+
+/* Initialize io tables */
+void __init h720x_map_io(void)
+{
+	iotable_init(h720x_io_desc,ARRAY_SIZE(h720x_io_desc));
+}

arch/arm/mach-h720x/cpu-h7201.c

+/*
+ * linux/arch/arm/mach-h720x/cpu-h7201.c
+ *
+ * Copyright (C) 2003 Thomas Gleixner <tglx@linutronix.de>
+ *               2003 Robert Schwebel <r.schwebel@pengutronix.de>
+ *               2004 Sascha Hauer    <s.hauer@pengutronix.de>
+ *
+ * processor specific stuff for the Hynix h7201
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <asm/types.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/arch/irqs.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/time.h>
+
+extern unsigned long h720x_gettimeoffset(void);
+extern void __init h720x_init_irq (void);
+
+/*
+ * Timer interrupt handler
+ */
+static irqreturn_t
+h7201_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+	CPU_REG (TIMER_VIRT, TIMER_TOPSTAT);
+	timer_tick(regs);
+	return IRQ_HANDLED;
+}
+
+static struct irqaction h7201_timer_irq = {
+	.name		= "h7201 Timer Tick",
+	.flags		= SA_INTERRUPT,
+	.handler	= h7201_timer_interrupt
+};
+
+/*
+ * Setup TIMER0 as system timer
+ */
+void __init h7201_init_time(void)
+{
+	gettimeoffset = h720x_gettimeoffset;
+
+	CPU_REG (TIMER_VIRT, TM0_PERIOD) = LATCH;
+	CPU_REG (TIMER_VIRT, TM0_CTRL) = TM_RESET;
+	CPU_REG (TIMER_VIRT, TM0_CTRL) = TM_REPEAT | TM_START;
+	CPU_REG (TIMER_VIRT, TIMER_TOPCTRL) = ENABLE_TM0_INTR | TIMER_ENABLE_BIT;
+
+	setup_irq(IRQ_TIMER0, &h7201_timer_irq);
+}

arch/arm/mach-h720x/cpu-h7202.c

+/*
+ * linux/arch/arm/mach-h720x/cpu-h7202.c
+ *
+ * Copyright (C) 2003 Thomas Gleixner <tglx@linutronix.de>
+ *               2003 Robert Schwebel <r.schwebel@pengutronix.de>
+ *               2004 Sascha Hauer    <s.hauer@pengutronix.de>
+ *
+ * processor specific stuff for the Hynix h7201
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <asm/types.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/arch/irqs.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/time.h>
+#include <linux/device.h>
+
+static struct resource h7202ps2_resources[] = {
+	[0] = {
+		.start	= 0x8002c000,
+		.end	= 0x8002c040,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= IRQ_PS2,
+		.end	= IRQ_PS2,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device h7202ps2_device = {
+	.name		= "h7202ps2",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(h7202ps2_resources),
+	.resource	= h7202ps2_resources,
+};
+
+static struct platform_device *devices[] __initdata = {
+	&h7202ps2_device,
+};
+
+extern unsigned long h720x_gettimeoffset(void);
+extern void __init h720x_init_irq (void);
+
+/* Although we have two interrupt lines for the timers, we only have one
+ * status register which clears all pending timer interrupts on reading. So
+ * we have to handle all timer interrupts in one place.
+ */
+static void
+h7202_timerx_demux_handler(unsigned int irq_unused, struct irqdesc *desc,
+			struct pt_regs *regs)
+{
+	unsigned int mask, irq;
+
+	mask = CPU_REG (TIMER_VIRT, TIMER_TOPSTAT);
+
+	if ( mask & TSTAT_T0INT ) {
+		timer_tick(regs);
+		if( mask == TSTAT_T0INT )
+			return;
+	}
+
+	mask >>= 1;
+	irq = IRQ_TIMER1;
+	desc = irq_desc + irq;
+	while (mask) {
+		if (mask & 1)
+			desc->handle(irq, desc, regs);
+		irq++;
+		desc++;
+		mask >>= 1;
+	}
+}
+
+/*
+ * Timer interrupt handler
+ */
+static irqreturn_t
+h7202_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+	h7202_timerx_demux_handler(0, NULL, regs);
+	return IRQ_HANDLED;
+}
+
+/*
+ * mask multiplexed timer irq's
+ */
+static void inline mask_timerx_irq (u32 irq)
+{
+	unsigned int bit;
+	bit = 2 << ((irq == IRQ_TIMER64B) ? 4 : (irq - IRQ_TIMER1));
+	CPU_REG (TIMER_VIRT, TIMER_TOPCTRL) &= ~bit;
+}
+
+/*
+ * unmask multiplexed timer irq's
+ */
+static void inline unmask_timerx_irq (u32 irq)
+{
+	unsigned int bit;
+	bit = 2 << ((irq == IRQ_TIMER64B) ? 4 : (irq - IRQ_TIMER1));
+	CPU_REG (TIMER_VIRT, TIMER_TOPCTRL) |= bit;
+}
+
+static struct irqchip h7202_timerx_chip = {
+	.ack = mask_timerx_irq,
+	.mask = mask_timerx_irq,
+	.unmask = unmask_timerx_irq,
+};
+
+static struct irqaction h7202_timer_irq = {
+	.name		= "h7202 Timer Tick",
+	.flags		= SA_INTERRUPT,
+	.handler	= h7202_timer_interrupt
+};
+
+/*
+ * Setup TIMER0 as system timer
+ */
+void __init h7202_init_time(void)
+{
+	gettimeoffset = h720x_gettimeoffset;
+
+	CPU_REG (TIMER_VIRT, TM0_PERIOD) = LATCH;
+	CPU_REG (TIMER_VIRT, TM0_CTRL) = TM_RESET;
+	CPU_REG (TIMER_VIRT, TM0_CTRL) = TM_REPEAT | TM_START;
+	CPU_REG (TIMER_VIRT, TIMER_TOPCTRL) = ENABLE_TM0_INTR | TIMER_ENABLE_BIT;
+
+	setup_irq(IRQ_TIMER0, &h7202_timer_irq);
+}
+
+void __init h7202_init_irq (void)
+{
+	int 	irq;
+
+	CPU_REG (GPIO_E_VIRT, GPIO_MASK) = 0x0;
+
+	for (irq = IRQ_TIMER1;
+	                  irq < IRQ_CHAINED_TIMERX(NR_TIMERX_IRQS); irq++) {
+		mask_timerx_irq(irq);
+		set_irq_chip(irq, &h7202_timerx_chip);
+		set_irq_handler(irq, do_edge_IRQ);
+		set_irq_flags(irq, IRQF_VALID );
+	}
+	set_irq_chained_handler(IRQ_TIMERX, h7202_timerx_demux_handler);
+
+	h720x_init_irq();
+}
+
+void __init init_hw_h7202(void)
+{
+	/* Enable clocks */
+	CPU_REG (PMU_BASE, PMU_PLL_CTRL) |= PLL_2_EN | PLL_1_EN | PLL_3_MUTE;
+
+	(void) platform_add_devices(devices, ARRAY_SIZE(devices));
+}

arch/arm/mach-h720x/h7201-eval.c

+/*
+ * linux/arch/arm/mach-h720x/h7201-eval.c
+ *
+ * Copyright (C) 2003 Thomas Gleixner <tglx@linutronix.de>
+ *               2003 Robert Schwebel <r.schwebel@pengutronix.de>
+ *               2004 Sascha Hauer    <s.hauer@pengutronix.de>
+ *
+ * Architecture specific stuff for Hynix GMS30C7201 development board
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/string.h>
+#include <linux/device.h>
+
+#include <asm/setup.h>
+#include <asm/types.h>
+#include <asm/mach-types.h>
+#include <asm/page.h>
+#include <asm/pgtable.h>
+#include <asm/mach/arch.h>
+#include <asm/hardware.h>
+
+extern void h720x_init_irq (void);
+extern void h7201_init_time(void);
+extern void __init h720x_map_io(void);
+
+MACHINE_START(H7201, "Hynix GMS30C7201")
+	MAINTAINER("Robert Schwebel, Pengutronix")
+	BOOT_MEM(0x40000000, 0x80000000, 0xf0000000)
+	BOOT_PARAMS(0xc0001000)
+	MAPIO(h720x_map_io)
+	INITIRQ(h720x_init_irq)
+	INITTIME(h7201_init_time)
+MACHINE_END

arch/arm/mach-h720x/h7202-eval.c

+/*
+ * linux/arch/arm/mach-h720x/h7202-eval.c
+ *
+ * Copyright (C) 2003 Thomas Gleixner <tglx@linutronix.de>
+ *               2003 Robert Schwebel <r.schwebel@pengutronix.de>
+ *		 2004 Sascha Hauer <s.hauer@pengutronix.de>
+ *
+ * Architecture specific stuff for Hynix HMS30C7202 development board
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/string.h>
+#include <linux/device.h>
+
+#include <asm/setup.h>
+#include <asm/types.h>
+#include <asm/mach-types.h>
+#include <asm/page.h>
+#include <asm/pgtable.h>
+#include <asm/mach/arch.h>
+#include <asm/hardware.h>
+
+extern void __init init_hw_h7202(void);
+extern void __init h7202_init_irq (void);
+extern void __init h7202_init_time(void);
+extern void __init h720x_map_io(void);
+
+static struct resource cirrus_resources[] = {
+	[0] = {
+		.start	= ETH0_PHYS + 0x300,
+		.end	= ETH0_PHYS + 0x300 + 0x10,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= IRQ_CHAINED_GPIOB(8),
+		.end	= IRQ_CHAINED_GPIOB(8),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device cirrus_device = {
+	.name		= "cirrus-cs89x0",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(cirrus_resources),
+	.resource	= cirrus_resources,
+};
+
+static struct platform_device *devices[] __initdata = {
+	&cirrus_device,
+};
+
+/*
+ * Hardware init. This is called early in initcalls
+ * Place pin inits here. So you avoid adding ugly
+ * #ifdef stuff to common drivers.
+ * Use this only, if your bootloader is not able
+ * to initialize the pins proper.
+ */
+static void __init init_eval_h7202(void)
+{
+	init_hw_h7202();
+	(void) platform_add_devices(devices, ARRAY_SIZE(devices));
+
+	/* Enable interrupt on portb bit 8 (ethernet) */
+	CPU_REG (GPIO_B_VIRT, GPIO_POL) &= ~(1 << 8);
+	CPU_REG (GPIO_B_VIRT, GPIO_EN) |= (1 << 8);
+}
+
+MACHINE_START(H7202, "Hynix HMS30C7202")
+	MAINTAINER("Robert Schwebel, Pengutronix")
+	BOOT_MEM(0x40000000, 0x80000000, 0xf0000000)
+	BOOT_PARAMS(0x40000100)
+	MAPIO(h720x_map_io)
+	INITIRQ(h7202_init_irq)
+	INITTIME(h7202_init_time)
+	INIT_MACHINE(init_eval_h7202)
+MACHINE_END

arch/arm/mm/Kconfig

@@ -43,7 +43,7 @@ config CPU_ARM710
 # ARM720T
 config CPU_ARM720T
 	bool "Support ARM720T processor" if !ARCH_CLPS711X && !ARCH_L7200 && !ARCH_CDB89712 && ARCH_INTEGRATOR
-	default y if ARCH_CLPS711X || ARCH_L7200 || ARCH_CDB89712
+	default y if ARCH_CLPS711X || ARCH_L7200 || ARCH_CDB89712 || ARCH_H720X
 	select CPU_32v4
 	select CPU_ABRT_LV4T
 	select CPU_CACHE_V4

arch/s390/appldata/appldata_mem.c

@@ -102,8 +102,12 @@ static inline void appldata_debug_print(struct appldata_mem_data *mem_data)
  */
 static void appldata_get_mem_data(void *data)
 {
-	struct sysinfo val;
-	struct page_state ps;
+	/*
+	 * don't put large structures on the stack, we are
+	 * serialized through the appldata_ops_lock and can use static
+	 */
+	static struct sysinfo val;
+	static struct page_state ps;
 	struct appldata_mem_data *mem_data;
 
 	mem_data = data;

arch/s390/defconfig

 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.9-rc2
-# Mon Sep 20 17:16:38 2004
+# Linux kernel version: 2.6.9-rc3
+# Fri Oct  8 19:17:35 2004
 #
 CONFIG_MMU=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
@@ -520,7 +520,7 @@ CONFIG_CRYPTO=y
 # CONFIG_CRYPTO_SHA1_Z990 is not set
 # CONFIG_CRYPTO_SHA256 is not set
 # CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WHIRLPOOL is not set
+# CONFIG_CRYPTO_WP512 is not set
 # CONFIG_CRYPTO_DES is not set
 # CONFIG_CRYPTO_DES_Z990 is not set
 # CONFIG_CRYPTO_BLOWFISH is not set

arch/s390/kernel/compat_signal.c

@@ -118,10 +118,10 @@ int copy_siginfo_from_user32(siginfo_t *to, siginfo_t32 __user *from)
 	err |= __get_user(to->si_errno, &from->si_errno);
 	err |= __get_user(to->si_code, &from->si_code);
 
-	if (from->si_code < 0)
+	if (to->si_code < 0)
 		err |= __copy_from_user(&to->_sifields._pad, &from->_sifields._pad, SI_PAD_SIZE);
 	else {
-		switch (from->si_code >> 16) {
+		switch (to->si_code >> 16) {
 		case __SI_RT >> 16: /* This is not generated by the kernel as of now.  */
 		case __SI_MESGQ >> 16:
 			err |= __get_user(to->si_int, &from->si_int);

arch/s390/kernel/s390_ksyms.c

@@ -34,6 +34,7 @@ EXPORT_SYMBOL(__clear_user_asm);
 EXPORT_SYMBOL(__strncpy_from_user_asm);
 EXPORT_SYMBOL(__strnlen_user_asm);
 EXPORT_SYMBOL(diag10);
+EXPORT_SYMBOL(default_storage_key);
 
 /*
  * semaphore ops

arch/s390/kernel/setup.c

@@ -53,6 +53,7 @@ unsigned int console_devno = -1;
 unsigned int console_irq = -1;
 unsigned long memory_size = 0;
 unsigned long machine_flags = 0;
+unsigned int default_storage_key = 0;
 struct {
 	unsigned long addr, size, type;
 } memory_chunk[MEMORY_CHUNKS] = { { 0 } };

arch/sparc/kernel/init_task.c

@@ -23,6 +23,6 @@ EXPORT_SYMBOL(init_task);
  * in etrap.S which assumes it.
  */
 union thread_union init_thread_union
-	__attribute__((section (".text,#alloc")))
+	__attribute__((section (".text\"\n\t#")))
 	__attribute__((aligned (THREAD_SIZE)))
 	= { INIT_THREAD_INFO(init_task) };

drivers/char/drm/drmP.h

@@ -458,13 +458,6 @@ typedef struct drm_device_dma {
 		_DRM_DMA_USE_SG  = 0x02
 	} flags;
 
-	/** \name DMA support */
-	/*@{*/
-	drm_buf_t	  *this_buffer;	/**< Buffer being sent */
-	drm_buf_t	  *next_buffer; /**< Selected buffer to send */
-	drm_queue_t	  *next_queue;	/**< Queue from which buffer selected*/
-	wait_queue_head_t waiting;	/**< Processes waiting on free bufs */
-	/*@}*/
 } drm_device_dma_t;
 
 /** 

drivers/char/drm/drm_core.h

+/*
+ * Copyright 2004 Jon Smirl <jonsmirl@gmail.com>
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sub license,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the
+ * next paragraph) shall be included in all copies or substantial portions
+ * of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL
+ * VIA, S3 GRAPHICS, AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ */
+
+#include "drm_auth.h"
+#include "drm_agpsupport.h"
+#include "drm_bufs.h"
+#include "drm_context.h"
+#include "drm_dma.h"
+#include "drm_irq.h"
+#include "drm_drawable.h"
+#include "drm_drv.h"
+#include "drm_fops.h"
+#include "drm_init.h"
+#include "drm_ioctl.h"
+#include "drm_lock.h"
+#include "drm_memory.h"
+#include "drm_proc.h"
+#include "drm_vm.h"
+#include "drm_stub.h"
+#include "drm_scatter.h"

drivers/char/drm/drm_irq.h

@@ -117,10 +117,6 @@ int DRM(irq_install)( drm_device_t *dev )
 
 	DRM_DEBUG( "%s: irq=%d\n", __FUNCTION__, dev->irq );
 
-	dev->dma->next_buffer = NULL;
-	dev->dma->next_queue = NULL;
-	dev->dma->this_buffer = NULL;
-
 	if (drm_core_check_feature(dev, DRIVER_IRQ_VBL)) {
 		init_waitqueue_head(&dev->vbl_queue);
 		

drivers/char/drm/ffb_drv.c

@@ -210,12 +210,7 @@ unsigned long ffb_get_unmapped_area(struct file *filp,
 	return addr;
 }
 
-#include "drm_auth.h"
-#include "drm_bufs.h"
-#include "drm_context.h"
-#include "drm_dma.h"
-#include "drm_drawable.h"
-#include "drm_drv.h"
+#include "drm_core.h"
 
 /* This functions must be here since it references DRM(numdevs)
  * which drm_drv.h declares.
@@ -254,18 +249,6 @@ static int ffb_presetup(drm_device_t *dev)
 	return ret;
 }
 
-#include "drm_fops.h"
-#include "drm_init.h"
-#include "drm_ioctl.h"
-#include "drm_irq.h"
-#include "drm_lock.h"
-#include "drm_memory.h"
-#include "drm_proc.h"
-#include "drm_vm.h"
-#include "drm_stub.h"
-#include "drm_scatter.h"
-
-
 static void ffb_driver_release(drm_device_t *dev, struct file *filp)
 {
 	ffb_dev_priv_t *fpriv = (ffb_dev_priv_t *) dev->dev_private;

drivers/char/drm/i810_drv.c

@@ -37,21 +37,4 @@
 #include "i810_drm.h"
 #include "i810_drv.h"
 
-#include "drm_agpsupport.h"
-#include "drm_auth.h"
-#include "drm_bufs.h"
-#include "drm_context.h"
-#include "drm_dma.h"
-#include "drm_drawable.h"
-#include "drm_drv.h"
-
-#include "drm_fops.h"
-#include "drm_init.h"
-#include "drm_ioctl.h"
-#include "drm_irq.h"
-#include "drm_lock.h"
-#include "drm_memory.h"
-#include "drm_proc.h"
-#include "drm_vm.h"
-#include "drm_stub.h"
-#include "drm_scatter.h"
+#include "drm_core.h"

drivers/char/drm/i830_drv.c

@@ -39,21 +39,4 @@
 #include "i830_drm.h"
 #include "i830_drv.h"
 
-#include "drm_agpsupport.h"
-#include "drm_auth.h"
-#include "drm_bufs.h"
-#include "drm_context.h"
-#include "drm_dma.h"
-#include "drm_drawable.h"
-#include "drm_drv.h"
-
-#include "drm_fops.h"
-#include "drm_init.h"
-#include "drm_ioctl.h"
-#include "drm_irq.h"
-#include "drm_lock.h"
-#include "drm_memory.h"
-#include "drm_proc.h"
-#include "drm_vm.h"
-#include "drm_stub.h"
-#include "drm_scatter.h"
+#include "drm_core.h"

drivers/char/drm/i915_drv.c

@@ -14,20 +14,4 @@
 #include "i915_drm.h"
 #include "i915_drv.h"
 
-#include "drm_agpsupport.h"
-#include "drm_auth.h"		/* is this needed? */
-#include "drm_bufs.h"
-#include "drm_context.h"	/* is this needed? */
-#include "drm_drawable.h"	/* is this needed? */
-#include "drm_dma.h"
-#include "drm_drv.h"
-#include "drm_fops.h"
-#include "drm_init.h"
-#include "drm_irq.h"
-#include "drm_ioctl.h"
-#include "drm_lock.h"
-#include "drm_memory.h"		/*  */
-#include "drm_proc.h"
-#include "drm_vm.h"
-#include "drm_stub.h"
-#include "drm_scatter.h"
+#include "drm_core.h"

drivers/char/drm/mga_drv.c

@@ -35,20 +35,4 @@
 #include "drm.h"
 #include "mga_drm.h"
 #include "mga_drv.h"
-#include "drm_agpsupport.h"
-#include "drm_auth.h"
-#include "drm_bufs.h"
-#include "drm_context.h"
-#include "drm_dma.h"
-#include "drm_drawable.h"
-#include "drm_drv.h"
-#include "drm_fops.h"
-#include "drm_init.h"
-#include "drm_ioctl.h"
-#include "drm_irq.h"
-#include "drm_lock.h"
-#include "drm_memory.h"
-#include "drm_proc.h"
-#include "drm_vm.h"
-#include "drm_stub.h"
-#include "drm_scatter.h"
+#include "drm_core.h"

drivers/char/drm/r128_drv.c

@@ -37,20 +37,4 @@
 #include "r128_drv.h"
 #include "ati_pcigart.h"
 
-#include "drm_agpsupport.h"
-#include "drm_auth.h"
-#include "drm_bufs.h"
-#include "drm_context.h"
-#include "drm_dma.h"
-#include "drm_drawable.h"
-#include "drm_drv.h"
-#include "drm_fops.h"
-#include "drm_init.h"
-#include "drm_ioctl.h"
-#include "drm_irq.h"
-#include "drm_lock.h"
-#include "drm_memory.h"
-#include "drm_proc.h"
-#include "drm_vm.h"
-#include "drm_stub.h"
-#include "drm_scatter.h"
+#include "drm_core.h"

drivers/char/drm/radeon_drv.c

@@ -38,20 +38,4 @@
 #include "radeon_drv.h"
 #include "ati_pcigart.h"
 
-#include "drm_agpsupport.h"
-#include "drm_auth.h"
-#include "drm_bufs.h"
-#include "drm_context.h"
-#include "drm_dma.h"
-#include "drm_drawable.h"
-#include "drm_drv.h"
-#include "drm_fops.h"
-#include "drm_init.h"
-#include "drm_ioctl.h"
-#include "drm_irq.h"
-#include "drm_lock.h"
-#include "drm_memory.h"
-#include "drm_proc.h"
-#include "drm_vm.h"
-#include "drm_stub.h"
-#include "drm_scatter.h"
+#include "drm_core.h"

drivers/char/drm/sis_drv.c

@@ -31,21 +31,4 @@
 #include "sis_drm.h"
 #include "sis_drv.h"
 
-#include "drm_auth.h"
-#include "drm_agpsupport.h"
-#include "drm_bufs.h"
-#include "drm_context.h"
-#include "drm_dma.h"
-#include "drm_drawable.h"
-#include "drm_drv.h"
-#include "drm_fops.h"
-#include "drm_init.h"
-#include "drm_irq.h"
-#include "drm_ioctl.h"
-#include "drm_lock.h"
-#include "drm_memory.h"
-#include "drm_proc.h"
-#include "drm_vm.h"
-#include "drm_stub.h"
-#include "drm_scatter.h"
-
+#include "drm_core.h"

drivers/char/drm/tdfx_drv.c

@@ -34,24 +34,7 @@
 #include "tdfx.h"
 #include "drmP.h"
 
-#include "drm_agpsupport.h"
-#include "drm_auth.h"
-#include "drm_bufs.h"
-#include "drm_context.h"
-#include "drm_dma.h"
-#include "drm_drawable.h"
-#include "drm_drv.h"
-
-#include "drm_fops.h"
-#include "drm_init.h"
-#include "drm_ioctl.h"
-#include "drm_irq.h"
-#include "drm_lock.h"
-#include "drm_memory.h"
-#include "drm_proc.h"
-#include "drm_vm.h"
-#include "drm_stub.h"
-#include "drm_scatter.h"
+#include "drm_core.h"
 
 void DRM(driver_register_fns)(drm_device_t *dev)
 {

drivers/input/mouse/pc110pad.c

@@ -109,9 +109,9 @@ static int pc110pad_open(struct input_dev *dev)
 
 static int __init pc110pad_init(void)
 {
-	if (request_region(pc110pad_io, 4, "pc110pad"))
-	{
-		printk(KERN_ERR "pc110pad: I/O area %#x-%#x in use.\n", pc110pad_io, pc110pad_io + 4);
+	if (!request_region(pc110pad_io, 4, "pc110pad")) {
+		printk(KERN_ERR "pc110pad: I/O area %#x-%#x in use.\n",
+				pc110pad_io, pc110pad_io + 4);
 		return -EBUSY;
 	}
 

drivers/macintosh/therm_adt746x.c

@@ -54,7 +54,7 @@ MODULE_DESCRIPTION("Driver for ADT746x thermostat in iBook G4 and Powerbook G4 A
 MODULE_LICENSE("GPL");
 
 MODULE_PARM(limit_adjust,"i");
-MODULE_PARM_DESC(limit_adjust,"Adjust maximum temperatures (50°C cpu, 70°C gpu) by N °C.");
+MODULE_PARM_DESC(limit_adjust,"Adjust maximum temperatures (50 cpu, 70 gpu) by N degrees.");
 MODULE_PARM(fan_speed,"i");
 MODULE_PARM_DESC(fan_speed,"Specify fan speed (0-255) when lim < temp < lim+8 (default 128)");
 
@@ -140,7 +140,7 @@ detach_thermostat(struct i2c_adapter *adapter)
 	}
 		
 	printk(KERN_INFO "adt746x: Putting max temperatures back from %d, %d, %d,"
-		" to %d, %d, %d, (°C)\n", 
+		" to %d, %d, %d\n",
 		th->limits[0], th->limits[1], th->limits[2],
 		th->initial_limits[0], th->initial_limits[1], th->initial_limits[2]);
 	
@@ -176,7 +176,8 @@ static int read_fan_speed(struct thermostat *th, u8 addr)
 	tmp[0] = read_reg(th, addr + 1);
 	
 	res = tmp[1] + (tmp[0] << 8);
-	return (90000*60)/res;
+	/* "a value of 0xffff means that the fan has stopped" */
+	return (res == 0xffff ? 0 : (90000*60)/res);
 }
 
 static void write_both_fan_speed(struct thermostat *th, int speed)
@@ -261,14 +262,14 @@ static int monitor_task(void *arg)
 				int var = temps[i] - lims[i];
 				if (var > 8) {
 					if (th->overriding[fan_number] == 0)
-						printk(KERN_INFO "adt746x: Limit exceeded by %d°C, overriding specified fan speed for %s.\n",
+						printk(KERN_INFO "adt746x: Limit exceeded by %d, overriding specified fan speed for %s.\n",
 							var, fan_number?"GPU":"CPU");
 					th->overriding[fan_number] = 1;
 					write_fan_speed(th, 255, fan_number);
 					started = 1;
 				} else if ((!th->overriding[fan_number] || var < 6) && var > 0) {
 					if (th->overriding[fan_number] == 1)
-						printk(KERN_INFO "adt746x: Limit exceeded by %d°C, setting speed to specified for %s.\n",
+						printk(KERN_INFO "adt746x: Limit exceeded by %d, setting speed to specified for %s.\n",
 							var, fan_number?"GPU":"CPU");					
 					th->overriding[fan_number] = 0;
 					write_fan_speed(th, fan_speed, fan_number);
@@ -299,8 +300,8 @@ static int monitor_task(void *arg)
 		||  temps[1] != th->cached_temp[1]
 		||  temps[2] != th->cached_temp[2]) {
 			printk(KERN_INFO "adt746x: Temperature infos:"
-					 " thermostats: %d,%d,%d °C;"
-					 " limits: %d,%d,%d °C;"
+					 " thermostats: %d,%d,%d;"
+					 " limits: %d,%d,%d;"
 					 " fan speed: %d RPM\n",
 				temps[0], temps[1], temps[2],
 				lims[0],  lims[1],  lims[2],
@@ -370,7 +371,7 @@ attach_one_thermostat(struct i2c_adapter *adapter, int addr, int busno)
 	}
 	
 	printk(KERN_INFO "adt746x: Lowering max temperatures from %d, %d, %d"
-		" to %d, %d, %d (°C)\n", 
+		" to %d, %d, %d\n",
 		th->initial_limits[0], th->initial_limits[1], th->initial_limits[2], 
 		th->limits[0], th->limits[1], th->limits[2]);
 
@@ -416,6 +417,15 @@ static ssize_t show_##name(struct device *dev, char *buf)	\
 	return sprintf(buf, "%d\n", data);			\
 }
 
+#define BUILD_SHOW_FUNC_FAN(name, data)				\
+static ssize_t show_##name(struct device *dev, char *buf)       \
+{								\
+	return sprintf(buf, "%d (%d rpm)\n", 			\
+		thermostat->last_speed[data],			\
+		read_fan_speed(thermostat, FAN_SPEED[data])	\
+		);						\
+}
+
 #define BUILD_STORE_FUNC_DEG(name, data)			\
 static ssize_t store_##name(struct device *dev, const char *buf, size_t n) \
 {								\
@@ -436,7 +446,7 @@ static ssize_t store_##name(struct device *dev, const char *buf, size_t n) \
 	val = simple_strtoul(buf, NULL, 10);			\
 	if (val < 0 || val > 255)				\
 		return -EINVAL;					\
-	printk(KERN_INFO "Setting fan speed to %d\n", val);	\
+	printk(KERN_INFO "Setting specified fan speed to %d\n", val);	\
 	data = val;						\
 	return n;						\
 }
@@ -447,8 +457,8 @@ BUILD_SHOW_FUNC_INT(cpu_limit,		 thermostat->limits[1])
 BUILD_SHOW_FUNC_INT(gpu_limit,		 thermostat->limits[2])
 
 BUILD_SHOW_FUNC_INT(specified_fan_speed, fan_speed)
-BUILD_SHOW_FUNC_INT(cpu_fan_speed,	 (read_fan_speed(thermostat, FAN_SPEED[0])))
-BUILD_SHOW_FUNC_INT(gpu_fan_speed,	 (read_fan_speed(thermostat, FAN_SPEED[1])))
+BUILD_SHOW_FUNC_FAN(cpu_fan_speed,	 0)
+BUILD_SHOW_FUNC_FAN(gpu_fan_speed,	 1)
 
 BUILD_STORE_FUNC_INT(specified_fan_speed,fan_speed)
 BUILD_SHOW_FUNC_INT(limit_adjust,	 limit_adjust)

drivers/s390/block/dasd_diag.c

@@ -6,7 +6,7 @@
  * Bugreports.to..: <Linux390@de.ibm.com>
  * (C) IBM Corporation, IBM Deutschland Entwicklung GmbH, 1999,2000
  *
- * $Revision: 1.37 $
+ * $Revision: 1.38 $
  */
 
 #include <linux/config.h>
@@ -304,8 +304,11 @@ dasd_diag_check_device(struct dasd_device *device)
 			    (device->bp_block >> 10),
 			    (device->blocks << device->s2b_shift) >> 1);
 		rc = 0;
-	} else
+	} else {
+		DEV_MESSAGE(KERN_WARNING, device, "%s",
+			    "volume has incompatible disk layout");
 		rc = -EMEDIUMTYPE;
+	}
 	free_page((long) label);
 	return rc;
 }

drivers/s390/block/dasd_eckd.c

@@ -7,7 +7,7 @@
  * Bugreports.to..: <Linux390@de.ibm.com>
  * (C) IBM Corporation, IBM Deutschland Entwicklung GmbH, 1999,2000
  *
- * $Revision: 1.59 $
+ * $Revision: 1.61 $
  */
 
 #include <linux/config.h>
@@ -505,11 +505,13 @@ dasd_eckd_check_characteristics(struct dasd_device *device)
 			"sizes of configuration data mismatch"
 			"%d (read) vs %ld (expected)",
 			conf_len, sizeof (struct dasd_eckd_confdata));
+
+		kfree(conf_data); /* allocated by read_conf_data() */
 		return 0;	/* no errror */
 	}
 	memcpy(&private->conf_data, conf_data,
 	       sizeof (struct dasd_eckd_confdata));
-
+	kfree(conf_data); /* allocated by read_conf_data() */
 	return 0;
 }
 

drivers/s390/block/dcssblk.c

@@ -5,6 +5,7 @@
  */
 
 #include <linux/module.h>
+#include <linux/moduleparam.h>
 #include <linux/ctype.h>
 #include <linux/errno.h>
 #include <linux/init.h>
@@ -19,6 +20,7 @@
 //#define DCSSBLK_DEBUG		/* Debug messages on/off */
 #define DCSSBLK_NAME "dcssblk"
 #define DCSSBLK_MINORS_PER_DISK 1
+#define DCSSBLK_PARM_LEN 400
 
 #ifdef DCSSBLK_DEBUG
 #define PRINT_DEBUG(x...) printk(KERN_DEBUG DCSSBLK_NAME " debug: " x)
@@ -34,6 +36,8 @@ static int dcssblk_open(struct inode *inode, struct file *filp);
 static int dcssblk_release(struct inode *inode, struct file *filp);
 static int dcssblk_make_request(struct request_queue *q, struct bio *bio);
 
+static char dcssblk_segments[DCSSBLK_PARM_LEN] = "\0";
+
 static int dcssblk_major;
 static struct block_device_operations dcssblk_devops = {
 	.owner   = THIS_MODULE,
@@ -641,6 +645,47 @@ dcssblk_make_request(request_queue_t *q, struct bio *bio)
 	return 0;
 }
 
+static void
+dcssblk_check_params(void)
+{
+	int rc, i, j, k;
+	char buf[9];
+	struct dcssblk_dev_info *dev_info;
+
+	for (i = 0; (i < DCSSBLK_PARM_LEN) && (dcssblk_segments[i] != '\0');
+	     i++) {
+		for (j = i; (dcssblk_segments[j] != ',')  &&
+			    (dcssblk_segments[j] != '\0') &&
+			    (dcssblk_segments[j] != '(')  &&
+			    (j - i) < 8; j++)
+		{
+			buf[j-i] = dcssblk_segments[j];
+		}
+		buf[j-i] = '\0';
+		rc = dcssblk_add_store(dcssblk_root_dev, buf, j-i);
+		if ((rc >= 0) && (dcssblk_segments[j] == '(')) {
+			for (k = 0; buf[k] != '\0'; k++)
+				buf[k] = toupper(buf[k]);
+			if (!strncmp(&dcssblk_segments[j], "(local)", 7)) {
+				down_read(&dcssblk_devices_sem);
+				dev_info = dcssblk_get_device_by_name(buf);
+				up_read(&dcssblk_devices_sem);
+				if (dev_info)
+					dcssblk_shared_store(&dev_info->dev,
+							     "0\n", 2);
+			}
+		}
+		while ((dcssblk_segments[j] != ',') &&
+		       (dcssblk_segments[j] != '\0'))
+		{
+			j++;
+		}
+		if (dcssblk_segments[j] == '\0')
+			break;
+		i = j;
+	}
+}
+
 /*
  * The init/exit functions.
  */
@@ -689,6 +734,9 @@ dcssblk_init(void)
 	}
 	dcssblk_major = rc;
 	init_rwsem(&dcssblk_devices_sem);
+
+	dcssblk_check_params();
+
 	PRINT_DEBUG("...finished!\n");
 	return 0;
 }
@@ -696,4 +744,12 @@ dcssblk_init(void)
 module_init(dcssblk_init);
 module_exit(dcssblk_exit);
 
+module_param_string(segments, dcssblk_segments, DCSSBLK_PARM_LEN, 0444);
+MODULE_PARM_DESC(segments, "Name of DCSS segment(s) to be loaded, "
+		 "comma-separated list, each name max. 8 chars.\n"
+		 "Adding \"(local)\" to segment name equals echoing 0 to "
+		 "/sys/devices/dcssblk/<segment name>/shared after loading "
+		 "the segment - \n"
+		 "e.g. segments=\"mydcss1,mydcss2,mydcss3(local)\"");
+
 MODULE_LICENSE("GPL");

drivers/s390/cio/blacklist.c

 /*
  *  drivers/s390/cio/blacklist.c
  *   S/390 common I/O routines -- blacklisting of specific devices
- *   $Revision: 1.31 $
+ *   $Revision: 1.33 $
  *
  *    Copyright (C) 1999-2002 IBM Deutschland Entwicklung GmbH,
  *			      IBM Corporation
@@ -229,7 +229,7 @@ s390_redo_validation (void)
 	unsigned int irq;
 
 	CIO_TRACE_EVENT (0, "redoval");
-	for (irq = 0; irq <= __MAX_SUBCHANNELS; irq++) {
+	for (irq = 0; irq < __MAX_SUBCHANNELS; irq++) {
 		int ret;
 		struct subchannel *sch;
 

drivers/s390/cio/ccwgroup.c

 /*
  *  drivers/s390/cio/ccwgroup.c
  *  bus driver for ccwgroup
- *   $Revision: 1.28 $
+ *   $Revision: 1.29 $
  *
  *    Copyright (C) 2002 IBM Deutschland Entwicklung GmbH,
  *                       IBM Corporation
@@ -191,14 +191,12 @@ ccwgroup_create(struct device *root,
 		gdev->cdev[i]->dev.driver_data = gdev;
 	del_drvdata = 1;
 
-	*gdev = (struct ccwgroup_device) {
-		.creator_id = creator_id,
-		.count = argc,
-		.dev = {
-			.bus = &ccwgroup_bus_type,
-			.parent = root,
-			.release = ccwgroup_release,
-		},
+	gdev->creator_id = creator_id;
+	gdev->count = argc;
+	gdev->dev = (struct device ) {
+		.bus = &ccwgroup_bus_type,
+		.parent = root,
+		.release = ccwgroup_release,
 	};
 
 	snprintf (gdev->dev.bus_id, BUS_ID_SIZE, "%s",

drivers/s390/cio/cio.c

 /*
  *  drivers/s390/cio/cio.c
  *   S/390 common I/O routines -- low level i/o calls
- *   $Revision: 1.123 $
+ *   $Revision: 1.128 $
  *
  *    Copyright (C) 1999-2002 IBM Deutschland Entwicklung GmbH,
  *			      IBM Corporation
@@ -141,6 +141,7 @@ cio_tpi(void)
 	sch = (struct subchannel *)(unsigned long)tpi_info->intparm;
 	if (!sch)
 		return 1;
+	local_bh_disable();
 	irq_enter ();
 	spin_lock(&sch->lock);
 	memcpy (&sch->schib.scsw, &irb->scsw, sizeof (struct scsw));
@@ -148,6 +149,7 @@ cio_tpi(void)
 		sch->driver->irq(&sch->dev);
 	spin_unlock(&sch->lock);
 	irq_exit ();
+	__local_bh_enable();
 	return 1;
 }
 
@@ -409,10 +411,10 @@ cio_enable_subchannel (struct subchannel *sch, unsigned int isc)
 	if (ccode)
 		return -ENODEV;
 
-	sch->schib.pmcw.ena = 1;
-	sch->schib.pmcw.isc = isc;
-	sch->schib.pmcw.intparm = (__u32)(unsigned long)sch;
 	for (retry = 5, ret = 0; retry > 0; retry--) {
+		sch->schib.pmcw.ena = 1;
+		sch->schib.pmcw.isc = isc;
+		sch->schib.pmcw.intparm = (__u32)(unsigned long)sch;
 		ret = cio_modify(sch);
 		if (ret == -ENODEV)
 			break;
@@ -463,9 +465,8 @@ cio_disable_subchannel (struct subchannel *sch)
 		 */
 		return -EBUSY;
 
-
-	sch->schib.pmcw.ena = 0;
 	for (retry = 5, ret = 0; retry > 0; retry--) {
+		sch->schib.pmcw.ena = 0;
 		ret = cio_modify(sch);
 		if (ret == -ENODEV)
 			break;

drivers/s390/cio/cmf.c

 /*
- * linux/drivers/s390/cio/cmf.c ($Revision: 1.15 $)
+ * linux/drivers/s390/cio/cmf.c ($Revision: 1.16 $)
  *
  * Linux on zSeries Channel Measurement Facility support
  *
@@ -526,29 +526,26 @@ readall_cmb (struct ccw_device *cdev, struct cmbdata *data)
 	time = get_clock() - cdev->private->cmb_start_time;
 	spin_unlock_irqrestore(cdev->ccwlock, flags);
 
-	*data = (struct cmbdata) {
-		/* we only know values before device_busy_time */
-		.size = offsetof(struct cmbdata, device_busy_time),
-
-		/* conver to nanoseconds */
-		.elapsed_time = (time * 1000) >> 12,
-
-		/* copy data to new structure */
-		.ssch_rsch_count		= cmb.ssch_rsch_count,
-		.sample_count			= cmb.sample_count,
-
-		/* time fields are converted to nanoseconds while copying */
-		.device_connect_time
-			= time_to_nsec(cmb.device_connect_time),
-		.function_pending_time
-			= time_to_nsec(cmb.function_pending_time),
-		.device_disconnect_time
-			= time_to_nsec(cmb.device_disconnect_time),
-		.control_unit_queuing_time
-		 	= time_to_nsec(cmb.control_unit_queuing_time),
-		.device_active_only_time
-			= time_to_nsec(cmb.device_active_only_time),
-	};
+	memset(data, sizeof(struct cmbdata), 0);
+
+	/* we only know values before device_busy_time */
+	data->size = offsetof(struct cmbdata, device_busy_time);
+
+	/* convert to nanoseconds */
+	data->elapsed_time = (time * 1000) >> 12;
+
+	/* copy data to new structure */
+	data->ssch_rsch_count = cmb.ssch_rsch_count;
+	data->sample_count = cmb.sample_count;
+
+	/* time fields are converted to nanoseconds while copying */
+	data->device_connect_time = time_to_nsec(cmb.device_connect_time);
+	data->function_pending_time = time_to_nsec(cmb.function_pending_time);
+	data->device_disconnect_time = time_to_nsec(cmb.device_disconnect_time);
+	data->control_unit_queuing_time
+		= time_to_nsec(cmb.control_unit_queuing_time);
+	data->device_active_only_time
+		= time_to_nsec(cmb.device_active_only_time);
 
 	return 0;
 }
@@ -739,33 +736,29 @@ readall_cmbe (struct ccw_device *cdev, struct cmbdata *data)
 	time = get_clock() - cdev->private->cmb_start_time;
 	spin_unlock_irqrestore(cdev->ccwlock, flags);
 
-	*data = (struct cmbdata) {
-		/* we only know values before device_busy_time */
-		.size = offsetof(struct cmbdata, device_busy_time),
-
-		/* conver to nanoseconds */
-		.elapsed_time = (time * 1000) >> 12,
-
-		/* copy data to new structure */
-		.ssch_rsch_count		= cmb.ssch_rsch_count,
-		.sample_count			= cmb.sample_count,
-
-		/* time fields are converted to nanoseconds while copying */
-		.device_connect_time
-			= time_to_nsec(cmb.device_connect_time),
-		.function_pending_time
-			= time_to_nsec(cmb.function_pending_time),
-		.device_disconnect_time
-			= time_to_nsec(cmb.device_disconnect_time),
-		.control_unit_queuing_time
-		 	= time_to_nsec(cmb.control_unit_queuing_time),
-		.device_active_only_time
-			= time_to_nsec(cmb.device_active_only_time),
-		.device_busy_time
-			= time_to_nsec(cmb.device_busy_time),
-		.initial_command_response_time
-			= time_to_nsec(cmb.initial_command_response_time),
-	};
+	memset (data, sizeof(struct cmbdata), 0);
+
+	/* we only know values before device_busy_time */
+	data->size = offsetof(struct cmbdata, device_busy_time);
+
+	/* conver to nanoseconds */
+	data->elapsed_time = (time * 1000) >> 12;
+
+	/* copy data to new structure */
+	data->ssch_rsch_count = cmb.ssch_rsch_count;
+	data->sample_count = cmb.sample_count;
+
+	/* time fields are converted to nanoseconds while copying */
+	data->device_connect_time = time_to_nsec(cmb.device_connect_time);
+	data->function_pending_time = time_to_nsec(cmb.function_pending_time);
+	data->device_disconnect_time = time_to_nsec(cmb.device_disconnect_time);
+	data->control_unit_queuing_time
+		= time_to_nsec(cmb.control_unit_queuing_time);
+	data->device_active_only_time
+		= time_to_nsec(cmb.device_active_only_time);
+	data->device_busy_time = time_to_nsec(cmb.device_busy_time);
+	data->initial_command_response_time
+		= time_to_nsec(cmb.initial_command_response_time);
 
 	return 0;
 }

drivers/s390/cio/css.c

 /*
  *  drivers/s390/cio/css.c
  *  driver for channel subsystem
- *   $Revision: 1.80 $
+ *   $Revision: 1.82 $
  *
  *    Copyright (C) 2002 IBM Deutschland Entwicklung GmbH,
  *			 IBM Corporation
@@ -278,7 +278,7 @@ css_rescan_devices(void)
 {
 	int irq, ret;
 
-	for (irq = 0; irq <= __MAX_SUBCHANNELS; irq++) {
+	for (irq = 0; irq < __MAX_SUBCHANNELS; irq++) {
 		ret = css_evaluate_subchannel(irq, 1);
 		/* No more memory. It doesn't make sense to continue. No
 		 * panic because this can happen in midflight and just
@@ -521,6 +521,7 @@ css_enqueue_subchannel_slow(unsigned long schid)
 	new_slow_sch = kmalloc(sizeof(struct slow_subchannel), GFP_ATOMIC);
 	if (!new_slow_sch)
 		return -ENOMEM;
+	memset(new_slow_sch, sizeof(struct slow_subchannel), 0);
 	new_slow_sch->schid = schid;
 	spin_lock_irqsave(&slow_subchannel_lock, flags);
 	list_add_tail(&new_slow_sch->slow_list, &slow_subchannels_head);

drivers/s390/cio/device.c

 /*
  *  drivers/s390/cio/device.c
  *  bus driver for ccw devices
- *   $Revision: 1.120 $
+ *   $Revision: 1.124 $
  *
  *    Copyright (C) 2002 IBM Deutschland Entwicklung GmbH,
  *			 IBM Corporation
@@ -540,6 +540,8 @@ get_disc_ccwdev_by_devno(unsigned int devno, struct ccw_device *sibling)
 	return cdev;
 }
 
+extern int css_get_ssd_info(struct subchannel *sch);
+
 void
 ccw_device_do_unreg_rereg(void *data)
 {
@@ -581,6 +583,8 @@ ccw_device_do_unreg_rereg(void *data)
 				device_unregister(&other_sch->dev);
 			}
 		}
+		/* Update ssd info here. */
+		css_get_ssd_info(sch);
 		cdev->private->devno = sch->schib.pmcw.dev;
 	} else
 		need_rename = 0;
@@ -633,7 +637,8 @@ io_subchannel_register(void *data)
 		sch->dev.driver_data = 0;
 		kfree (cdev->private);
 		kfree (cdev);
-		goto out;
+		put_device(&sch->dev);
+		return;
 	}
 
 	ret = subchannel_add_files(cdev->dev.parent);
@@ -707,18 +712,19 @@ static int
 io_subchannel_recog(struct ccw_device *cdev, struct subchannel *sch)
 {
 	int rc;
+	struct ccw_device_private *priv;
 
 	sch->dev.driver_data = cdev;
 	sch->driver = &io_subchannel_driver;
 	cdev->ccwlock = &sch->lock;
-	*cdev->private = (struct ccw_device_private) {
-		.devno	= sch->schib.pmcw.dev,
-		.irq	= sch->irq,
-		.state	= DEV_STATE_NOT_OPER,
-		.cmb_list = LIST_HEAD_INIT(cdev->private->cmb_list),
-	};
-	init_waitqueue_head(&cdev->private->wait_q);
-	init_timer(&cdev->private->timer);
+	/* Init private data. */
+	priv = cdev->private;
+	priv->devno = sch->schib.pmcw.dev;
+	priv->irq = sch->irq;
+	priv->state = DEV_STATE_NOT_OPER;
+	INIT_LIST_HEAD(&priv->cmb_list);
+	init_waitqueue_head(&priv->wait_q);
+	init_timer(&priv->timer);
 
 	/* Set an initial name for the device. */
 	snprintf (cdev->dev.bus_id, BUS_ID_SIZE, "0.0.%04x",

drivers/s390/cio/device_fsm.c

@@ -995,6 +995,7 @@ device_trigger_reprobe(struct subchannel *sch)
 	if ((sch->lpm & (sch->lpm - 1)) != 0)
 		sch->schib.pmcw.mp = 1;
 	sch->schib.pmcw.intparm = (__u32)(unsigned long)sch;
+	/* We should also udate ssd info, but this has to wait. */
 	ccw_device_start_id(cdev, 0);
 	spin_unlock_irqrestore(&sch->lock, flags);
 }

drivers/s390/cio/device_id.c

@@ -303,10 +303,10 @@ ccw_device_sense_id_irq(struct ccw_device *cdev, enum dev_event dev_event)
 
 	sch = to_subchannel(cdev->dev.parent);
 	irb = (struct irb *) __LC_IRB;
-	/* Retry sense id for cc=1. */
+	/* Retry sense id, if needed. */
 	if (irb->scsw.stctl ==
 	    (SCSW_STCTL_STATUS_PEND | SCSW_STCTL_ALERT_STATUS)) {
-		if (irb->scsw.cc == 1) {
+		if ((irb->scsw.cc == 1) || !irb->scsw.actl) {
 			ret = __ccw_device_sense_id_start(cdev);
 			if (ret && ret != -EBUSY)
 				ccw_device_sense_id_done(cdev, ret);

drivers/s390/net/qeth_main.c

 /*
  *
- * linux/drivers/s390/net/qeth_main.c ($Revision: 1.138 $)
+ * linux/drivers/s390/net/qeth_main.c ($Revision: 1.145 $)
  *
  * Linux on zSeries OSA Express and HiperSockets support
  *
@@ -12,7 +12,7 @@
  *			  Frank Pavlic (pavlic@de.ibm.com) and
  *		 	  Thomas Spatzier <tspat@de.ibm.com>
  *
- *    $Revision: 1.138 $	 $Date: 2004/09/17 10:40:53 $
+ *    $Revision: 1.145 $	 $Date: 2004/10/08 15:08:40 $
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
@@ -79,7 +79,7 @@ qeth_eyecatcher(void)
 #include "qeth_mpc.h"
 #include "qeth_fs.h"
 
-#define VERSION_QETH_C "$Revision: 1.138 $"
+#define VERSION_QETH_C "$Revision: 1.145 $"
 static const char *version = "qeth S/390 OSA-Express driver";
 
 /**
@@ -3835,6 +3835,7 @@ qeth_do_send_packet(struct qeth_card *card, struct qeth_qdio_out_q *queue,
 				/* return EBUSY because we sent old packet, not
 				 * the current one */
 				rc = -EBUSY;
+				atomic_set(&queue->state, QETH_OUT_Q_UNLOCKED);
 				goto out;
 			}
 		}

drivers/video/Kconfig

@@ -775,6 +775,7 @@ config FB_SIS_315
 config FB_NEOMAGIC
 	tristate "NeoMagic display support"
 	depends on FB && PCI
+	select FB_MODE_HELPERS
 	help
 	  This driver supports notebooks with NeoMagic PCI chips.
 	  Say Y if you have such a graphics card. 

fs/hugetlbfs/inode.c

@@ -651,6 +651,7 @@ hugetlbfs_fill_super(struct super_block *sb, void *data, int silent)
 	sbinfo->free_blocks = config.nr_blocks;
 	sbinfo->max_inodes = config.nr_inodes;
 	sbinfo->free_inodes = config.nr_inodes;
+	sb->s_maxbytes = MAX_LFS_FILESIZE;
 	sb->s_blocksize = HPAGE_SIZE;
 	sb->s_blocksize_bits = HPAGE_SHIFT;
 	sb->s_magic = HUGETLBFS_MAGIC;

include/asm-arm/arch-h720x/boards.h

+/*
+ * linux/include/asm-arm/arch-h720x/boards.h
+ *
+ * Copyright (C) 2003 Thomas Gleixner <tglx@linutronix.de>
+ *           (C) 2003 Robert Schwebel <r.schwebel@pengutronix.de>
+ *
+ * This file contains the board specific defines for various devices
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_HARDWARE_INCMACH_H
+#error Do not include this file directly. Include asm/hardware.h instead !
+#endif
+
+/* Hynix H7202 developer board specific device defines */
+#ifdef CONFIG_ARCH_H7202
+
+/* FLASH */
+#define FLASH_VIRT		0xd0000000
+#define FLASH_PHYS		0x00000000
+#define FLASH_SIZE		0x02000000
+
+/* onboard LAN controller */
+# define ETH0_PHYS		0x08000000
+
+/* Touch screen defines */
+/* GPIO Port */
+#define PEN_GPIO		GPIO_B_VIRT
+/* Bitmask for pen down interrupt */
+#define PEN_INT_BIT		(1<<7)
+/* Bitmask for pen up interrupt */
+#define PEN_ENA_BIT		(1<<6)
+/* pen up interrupt */
+#define IRQ_PEN			IRQ_MUX_GPIOB(7)
+
+#endif
+
+/* Hynix H7201 developer board specific device defines */
+#if defined (CONFIG_ARCH_H7201)
+/* ROM DISK SPACE */
+#define ROM_DISK_BASE           0xc1800000
+#define ROM_DISK_START          0x41800000
+#define ROM_DISK_SIZE           0x00700000
+
+/* SRAM DISK SPACE */
+#define SRAM_DISK_BASE          0xf1000000
+#define SRAM_DISK_START         0x04000000
+#define SRAM_DISK_SIZE          0x00400000
+#endif
+

include/asm-arm/arch-h720x/dma.h

+/*
+ * linux/include/asm-arm/arch-h720x/dma.h
+ *
+ * Architecture DMA routes
+ *
+ * Copyright (C) 1997.1998 Russell King
+ */
+#ifndef __ASM_ARCH_DMA_H
+#define __ASM_ARCH_DMA_H
+
+/*
+ * This is the maximum DMA address that can be DMAd to.
+ * There should not be more than (0xd0000000 - 0xc0000000)
+ * bytes of RAM.
+ */
+#define MAX_DMA_ADDRESS		0xd0000000
+
+#if defined (CONFIG_CPU_H7201)
+#define MAX_DMA_CHANNELS	3
+#elif defined (CONFIG_CPU_H7202)
+#define MAX_DMA_CHANNELS	4
+#else
+#error processor definition missmatch
+#endif
+
+#endif /* __ASM_ARCH_DMA_H */

include/asm-arm/arch-h720x/h7201-regs.h

+/*
+ * linux/include/asm-arm/arch-h720x/h7201-regs.h
+ *
+ * Copyright (C) 2000 Jungjun Kim, Hynix Semiconductor Inc.
+ *           (C) 2003 Thomas Gleixner <tglx@linutronix.de>
+ *           (C) 2003 Robert Schwebel <r.schwebel@pengutronix.de>
+ *           (C) 2004 Sascha Hauer    <s.hauer@pengutronix.de>
+ *
+ * This file contains the hardware definitions of the h720x processors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Do not add implementations specific defines here. This files contains
+ * only defines of the onchip peripherals. Add those defines to boards.h,
+ * which is included by this file.
+ */
+
+#define SERIAL2_VIRT 		(IO_VIRT + 0x50100)
+#define SERIAL3_VIRT 		(IO_VIRT + 0x50200)
+
+/*
+ * PCMCIA
+ */
+#define PCMCIA0_ATT_BASE        0xe5000000
+#define PCMCIA0_ATT_SIZE        0x00200000
+#define PCMCIA0_ATT_START       0x20000000
+#define PCMCIA0_MEM_BASE        0xe5200000
+#define PCMCIA0_MEM_SIZE        0x00200000
+#define PCMCIA0_MEM_START       0x24000000
+#define PCMCIA0_IO_BASE         0xe5400000
+#define PCMCIA0_IO_SIZE         0x00200000
+#define PCMCIA0_IO_START        0x28000000
+
+#define PCMCIA1_ATT_BASE        0xe5600000
+#define PCMCIA1_ATT_SIZE        0x00200000
+#define PCMCIA1_ATT_START       0x30000000
+#define PCMCIA1_MEM_BASE        0xe5800000
+#define PCMCIA1_MEM_SIZE        0x00200000
+#define PCMCIA1_MEM_START       0x34000000
+#define PCMCIA1_IO_BASE         0xe5a00000
+#define PCMCIA1_IO_SIZE         0x00200000
+#define PCMCIA1_IO_START        0x38000000
+
+#define PRIME3C_BASE            0xf0050000
+#define PRIME3C_SIZE            0x00001000
+#define PRIME3C_START           0x10000000
+
+/* VGA Controller */
+#define VGA_RAMBASE 		0x50
+#define VGA_TIMING0 		0x60
+#define VGA_TIMING1 		0x64
+#define VGA_TIMING2 		0x68
+#define VGA_TIMING3 		0x6c
+
+#define LCD_CTRL_VGA_ENABLE   	0x00000100
+#define LCD_CTRL_VGA_BPP_MASK 	0x00000600
+#define LCD_CTRL_VGA_4BPP    	0x00000000
+#define LCD_CTRL_VGA_8BPP    	0x00000200
+#define LCD_CTRL_VGA_16BPP   	0x00000300
+#define LCD_CTRL_SHARE_DMA    	0x00000800
+#define LCD_CTRL_VDE          	0x00100000
+#define LCD_CTRL_LPE          	0x00400000	/* LCD Power enable */
+#define LCD_CTRL_BLE          	0x00800000	/* LCD backlight enable */
+
+#define VGA_PALETTE_BASE	(IO_VIRT + 0x10800)

include/asm-arm/arch-h720x/h7202-regs.h

+/*
+ * linux/include/asm-arm/arch-h720x/h7202-regs.h
+ *
+ * Copyright (C) 2000 Jungjun Kim, Hynix Semiconductor Inc.
+ *           (C) 2003 Thomas Gleixner <tglx@linutronix.de>
+ *           (C) 2003 Robert Schwebel <r.schwebel@pengutronix.de>
+ *           (C) 2004 Sascha Hauer    <s.hauer@pengutronix.de>
+ *
+ * This file contains the hardware definitions of the h720x processors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Do not add implementations specific defines here. This files contains
+ * only defines of the onchip peripherals. Add those defines to boards.h,
+ * which is included by this file.
+ */
+
+#define SERIAL2_VIRT 		(IO_VIRT + 0x2d000)
+#define SERIAL3_VIRT 		(IO_VIRT + 0x2e000)
+
+/* Matrix Keyboard Controller */
+#define KBD_VIRT		(IO_VIRT + 0x22000)
+#define KBD_KBCR		0x00
+#define KBD_KBSC		0x04
+#define KBD_KBTR		0x08
+#define KBD_KBVR0		0x0C
+#define KBD_KBVR1		0x10
+#define KBD_KBSR		0x18
+
+#define KBD_KBCR_SCANENABLE	(1 << 7)
+#define KBD_KBCR_NPOWERDOWN	(1 << 2)
+#define KBD_KBCR_CLKSEL_MASK	(3)
+#define KBD_KBCR_CLKSEL_PCLK2	0x0
+#define KBD_KBCR_CLKSEL_PCLK128	0x1
+#define KBD_KBCR_CLKSEL_PCLK256	0x2
+#define KBD_KBCR_CLKSEL_PCLK512	0x3
+
+#define KBD_KBSR_INTR		(1 << 0)
+#define KBD_KBSR_WAKEUP		(1 << 1)
+
+/* USB device controller */
+
+#define USBD_BASE		(IO_VIRT + 0x12000)
+#define USBD_LENGTH		0x3C
+
+#define USBD_GCTRL		0x00
+#define USBD_EPCTRL		0x04
+#define USBD_INTMASK		0x08
+#define USBD_INTSTAT		0x0C
+#define USBD_PWR		0x10
+#define USBD_DMARXTX		0x14
+#define USBD_DEVID		0x18
+#define USBD_DEVCLASS		0x1C
+#define USBD_INTCLASS		0x20
+#define USBD_SETUP0		0x24
+#define USBD_SETUP1		0x28
+#define USBD_ENDP0RD		0x2C
+#define USBD_ENDP0WT		0x30
+#define USBD_ENDP1RD		0x34
+#define USBD_ENDP2WT		0x38
+
+/* PS/2 port */
+#define PSDATA 0x00
+#define PSSTAT 0x04
+#define PSSTAT_TXEMPTY (1<<0)
+#define PSSTAT_TXBUSY (1<<1)
+#define PSSTAT_RXFULL (1<<2)
+#define PSSTAT_RXBUSY (1<<3)
+#define PSSTAT_CLKIN (1<<4)
+#define PSSTAT_DATAIN (1<<5)
+#define PSSTAT_PARITY (1<<6)
+
+#define PSCONF 0x08
+#define PSCONF_ENABLE (1<<0)
+#define PSCONF_TXINTEN (1<<2)
+#define PSCONF_RXINTEN (1<<3)
+#define PSCONF_FORCECLKLOW (1<<4)
+#define PSCONF_FORCEDATLOW (1<<5)
+#define PSCONF_LCE (1<<6)
+
+#define PSINTR 0x0C
+#define PSINTR_TXINT (1<<0)
+#define PSINTR_RXINT (1<<1)
+#define PSINTR_PAR (1<<2)
+#define PSINTR_RXTO (1<<3)
+#define PSINTR_TXTO (1<<4)
+
+#define PSTDLO 0x10 /* clk low before start transmission */
+#define PSTPRI 0x14 /* PRI clock */
+#define PSTXMT 0x18 /* maximum transmission time */
+#define PSTREC 0x20 /* maximum receive time */
+#define PSPWDN 0x3c
+
+/* ADC converter */
+#define ADC_BASE 		(IO_VIRT + 0x29000)
+#define ADC_CR 			0x00
+#define ADC_TSCTRL 		0x04
+#define ADC_BT_CTRL 		0x08
+#define ADC_MC_CTRL		0x0C
+#define ADC_STATUS		0x10
+
+/* ADC control register bits */
+#define ADC_CR_PW_CTRL 		0x80
+#define ADC_CR_DIRECTC		0x04
+#define ADC_CR_CONTIME_NO	0x00
+#define ADC_CR_CONTIME_2	0x04
+#define ADC_CR_CONTIME_4	0x08
+#define ADC_CR_CONTIME_ADE	0x0c
+#define ADC_CR_LONGCALTIME	0x01
+
+/* ADC touch panel register bits */
+#define ADC_TSCTRL_ENABLE 	0x80
+#define ADC_TSCTRL_INTR   	0x40
+#define	ADC_TSCTRL_SWBYPSS	0x20
+#define ADC_TSCTRL_SWINVT	0x10
+#define ADC_TSCTRL_S400   	0x03
+#define ADC_TSCTRL_S200   	0x02
+#define ADC_TSCTRL_S100   	0x01
+#define ADC_TSCTRL_S50    	0x00
+
+/* ADC Interrupt Status Register bits */
+#define ADC_STATUS_TS_BIT	0x80
+#define ADC_STATUS_MBT_BIT	0x40
+#define ADC_STATUS_BBT_BIT	0x20
+#define ADC_STATUS_MIC_BIT	0x10
+
+/* Touch data registers */
+#define ADC_TS_X0X1  		0x30
+#define ADC_TS_X2X3		0x34
+#define ADC_TS_Y0Y1		0x38
+#define ADC_TS_Y2Y3  		0x3c
+#define ADC_TS_X4X5  		0x40
+#define ADC_TS_X6X7  		0x44
+#define ADC_TS_Y4Y5		0x48
+#define ADC_TS_Y6Y7		0x50
+
+/* battery data */
+#define ADC_MB_DATA		0x54
+#define ADC_BB_DATA		0x58
+
+/* Sound data register */
+#define ADC_SD_DAT0 		0x60
+#define ADC_SD_DAT1		0x64
+#define ADC_SD_DAT2		0x68
+#define ADC_SD_DAT3		0x6c
+#define ADC_SD_DAT4		0x70
+#define ADC_SD_DAT5		0x74
+#define ADC_SD_DAT6		0x78
+#define ADC_SD_DAT7		0x7c

include/asm-arm/arch-h720x/hardware.h

+/*
+ * linux/include/asm-arm/arch-h720x/hardware.h
+ *
+ * Copyright (C) 2000 Jungjun Kim, Hynix Semiconductor Inc.
+ *           (C) 2003 Thomas Gleixner <tglx@linutronix.de>
+ *           (C) 2003 Robert Schwebel <r.schwebel@pengutronix.de>
+ *
+ * This file contains the hardware definitions of the h720x processors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Do not add implementations specific defines here. This files contains
+ * only defines of the onchip peripherals. Add those defines to boards.h,
+ * which is included by this file.
+ */
+
+#ifndef __ASM_ARCH_HARDWARE_H
+#define __ASM_ARCH_HARDWARE_H
+
+#define IOCLK (3686400L)
+
+/* Onchip peripherals */
+
+#define IO_VIRT			0xf0000000	/* IO peripherals */
+#define IO_PHYS			0x80000000
+#define IO_SIZE			0x00050000
+
+#ifdef CONFIG_CPU_H7202
+#include "h7202-regs.h"
+#elif defined CONFIG_CPU_H7201
+#include "h7201-regs.h"
+#else
+#error machine definition mismatch
+#endif
+
+/* Macro to access the CPU IO */
+#define CPU_IO(x) (*(volatile u32*)(x))
+
+/* Macro to access general purpose regs (base, offset) */
+#define CPU_REG(x,y) CPU_IO(x+y)
+
+/* Macro to access irq related regs */
+#define IRQ_REG(x) CPU_REG(IRQC_VIRT,x)
+
+/* CPU registers */
+/* general purpose I/O */
+#define GPIO_VIRT(x)		(IO_VIRT + 0x23000 + ((x)<<5))
+#define GPIO_A_VIRT		(GPIO_VIRT(0))
+#define GPIO_B_VIRT		(GPIO_VIRT(1))
+#define GPIO_C_VIRT		(GPIO_VIRT(2))
+#define GPIO_D_VIRT		(GPIO_VIRT(3))
+#define GPIO_E_VIRT		(GPIO_VIRT(4))
+#define GPIO_AMULSEL		(GPIO_VIRT + 0xA4)
+/* Register offsets general purpose I/O */
+#define GPIO_DATA		0x00
+#define GPIO_DIR		0x04
+#define GPIO_MASK		0x08
+#define GPIO_STAT		0x0C
+#define GPIO_EDGE		0x10
+#define GPIO_CLR		0x14
+#define GPIO_POL		0x18
+#define GPIO_EN			0x1C
+
+/*interrupt controller */
+#define IRQC_VIRT		(IO_VIRT + 0x24000)
+/* register offset interrupt controller */
+#define IRQC_IER		0x00
+#define IRQC_ISR		0x04
+
+/* timer unit */
+#define TIMER_VIRT		(IO_VIRT + 0x25000)
+/* Register offsets timer unit */
+#define TM0_PERIOD   		0x00
+#define TM0_COUNT    		0x08
+#define TM0_CTRL     		0x10
+#define TM1_PERIOD   		0x20
+#define TM1_COUNT    		0x28
+#define TM1_CTRL     		0x30
+#define TM2_PERIOD   		0x40
+#define TM2_COUNT    		0x48
+#define TM2_CTRL     		0x50
+#define TIMER_TOPCTRL		0x60
+#define TIMER_TOPSTAT		0x64
+#define T64_COUNTL		0x80
+#define T64_COUNTH		0x84
+#define T64_CTRL		0x88
+#define T64_BASEL		0x94
+#define T64_BASEH		0x98
+/* Bitmaks timer unit TOPSTAT reg */
+#define TSTAT_T0INT		0x1
+#define TSTAT_T1INT		0x2
+#define TSTAT_T2INT		0x4
+#define TSTAT_T3INT		0x8
+/* Bit description of TMx_CTRL register */
+#define TM_START  		0x1
+#define TM_REPEAT 		0x2
+#define TM_RESET  		0x4
+/* Bit description of TIMER_CTRL register */
+#define ENABLE_TM0_INTR  	0x1
+#define ENABLE_TM1_INTR  	0x2
+#define ENABLE_TM2_INTR  	0x4
+#define TIMER_ENABLE_BIT 	0x8
+#define ENABLE_TIMER64   	0x10
+#define ENABLE_TIMER64_INT	0x20
+
+/* PMU & PLL */
+#define PMU_BASE 		(IO_VIRT + 0x1000)
+#define PMU_MODE		0x00
+#define PMU_STAT   		0x20
+#define PMU_PLL_CTRL 		0x28
+
+/* PMU Mode bits */
+#define PMU_MODE_SLOW		0x00
+#define PMU_MODE_RUN		0x01
+#define PMU_MODE_IDLE		0x02
+#define PMU_MODE_SLEEP		0x03
+#define PMU_MODE_INIT		0x04
+#define PMU_MODE_DEEPSLEEP	0x07
+#define PMU_MODE_WAKEUP		0x08
+
+/* PMU ... */
+#define PLL_2_EN		0x8000
+#define PLL_1_EN		0x4000
+#define PLL_3_MUTE		0x0080
+
+/* Control bits for PMU/ PLL */
+#define PMU_WARMRESET		0x00010000
+#define PLL_CTRL_MASK23		0x000080ff
+
+/* LCD Controller */
+#define LCD_BASE 		(IO_VIRT + 0x10000)
+#define LCD_CTRL 		0x00
+#define LCD_STATUS		0x04
+#define LCD_STATUS_M		0x08
+#define LCD_INTERRUPT		0x0C
+#define LCD_DBAR		0x10
+#define LCD_DCAR		0x14
+#define LCD_TIMING0 		0x20
+#define LCD_TIMING1 		0x24
+#define LCD_TIMING2 		0x28
+#define LCD_TEST		0x40
+
+/* LCD Control Bits */
+#define LCD_CTRL_LCD_ENABLE   	0x00000001
+/* Bits per pixel */
+#define LCD_CTRL_LCD_BPP_MASK 	0x00000006
+#define LCD_CTRL_LCD_4BPP    	0x00000000
+#define LCD_CTRL_LCD_8BPP    	0x00000002
+#define LCD_CTRL_LCD_16BPP   	0x00000004
+#define LCD_CTRL_LCD_BW		0x00000008
+#define LCD_CTRL_LCD_TFT	0x00000010
+#define LCD_CTRL_BGR		0x00001000
+#define LCD_CTRL_LCD_VCOMP	0x00080000
+#define LCD_CTRL_LCD_MONO8	0x00200000
+#define LCD_CTRL_LCD_PWR	0x00400000
+#define LCD_CTRL_LCD_BLE	0x00800000
+#define LCD_CTRL_LDBUSEN	0x01000000
+
+/* Palette */
+#define LCD_PALETTE_BASE 	(IO_VIRT + 0x10400)
+
+/* Serial ports */
+#define SERIAL0_VIRT 		(IO_VIRT + 0x20000)
+#define SERIAL1_VIRT 		(IO_VIRT + 0x21000)
+
+#define SERIAL0_BASE		SERIAL0_VIRT
+#define SERIAL1_BASE		SERIAL1_VIRT
+#define SERIAL2_BASE		SERIAL2_VIRT
+#define SERIAL3_BASE		SERIAL3_VIRT
+
+
+/* General defines to pacify gcc */
+#define PCIO_BASE 		(0)	/* for inb, outb and friends */
+#define PCIO_VIRT		PCIO_BASE
+
+#define __ASM_ARCH_HARDWARE_INCMACH_H
+#include "boards.h"
+#undef __ASM_ARCH_HARDWARE_INCMACH_H
+
+#endif				/* __ASM_ARCH_HARDWARE_H */

include/asm-arm/arch-h720x/io.h

+/*
+ * linux/include/asm-arm/arch-h720x/io.h
+ *
+ * Copyright (C) 2000 Steve Hill (sjhill@cotw.com)
+ *
+ * Changelog:
+ *
+ *  09-19-2001	JJKIM
+ *  		Created from linux/include/asm-arm/arch-l7200/io.h
+ *
+ *  03-27-2003  Robert Schwebel <r.schwebel@pengutronix.de>:
+ *  		re-unified header files for h720x
+ */
+#ifndef __ASM_ARM_ARCH_IO_H
+#define __ASM_ARM_ARCH_IO_H
+
+#include <asm/arch/hardware.h>
+
+#define IO_SPACE_LIMIT 0xffffffff
+
+#define __io(a) (a)
+#define __mem_pci(a) (a)
+
+#endif

include/asm-arm/arch-h720x/irq.h

+/*
+ * include/asm-arm/arch-h720x/irq.h
+ *
+ * Copyright (C) 2000-2002 Jungjun Kim
+ *           (C) 2003 Robert Schwebel <r.schwebel@pengutronix.de>
+ *           (C) 2003 Thomas Gleixner <tglx@linutronix.de>
+ */
+
+#ifndef __ASM_ARCH_IRQ_H
+#define __ASM_ARCH_IRQ_H
+
+extern void __init h720x_init_irq (void);
+
+#endif /* __ASM_ARCH_IRQ_H */

include/asm-arm/arch-h720x/irqs.h

+/*
+ * linux/include/asm-arm/arch-h720x/irqs.h
+ *
+ * Copyright (C) 2000 Jungjun Kim
+ *           (C) 2003 Robert Schwebel <r.schwebel@pengutronix.de>
+ *           (C) 2003 Thomas Gleixner <tglx@linutronix.de>
+ *
+ */
+
+#ifndef __ASM_ARCH_IRQS_H
+#define __ASM_ARCH_IRQS_H
+
+#if defined (CONFIG_CPU_H7201)
+
+#define IRQ_PMU		0		/* 0x000001 */
+#define IRQ_DMA		1 		/* 0x000002 */
+#define IRQ_LCD		2		/* 0x000004 */
+#define IRQ_VGA		3 		/* 0x000008 */
+#define IRQ_PCMCIA1 	4 		/* 0x000010 */
+#define IRQ_PCMCIA2 	5 		/* 0x000020 */
+#define IRQ_AFE		6 		/* 0x000040 */
+#define IRQ_AIC		7 		/* 0x000080 */
+#define IRQ_KEYBOARD 	8 		/* 0x000100 */
+#define IRQ_TIMER0	9 		/* 0x000200 */
+#define IRQ_RTC		10		/* 0x000400 */
+#define IRQ_SOUND	11		/* 0x000800 */
+#define IRQ_USB		12		/* 0x001000 */
+#define IRQ_IrDA 	13		/* 0x002000 */
+#define IRQ_UART0	14		/* 0x004000 */
+#define IRQ_UART1	15		/* 0x008000 */
+#define IRQ_SPI		16		/* 0x010000 */
+#define IRQ_GPIOA 	17		/* 0x020000 */
+#define IRQ_GPIOB	18		/* 0x040000 */
+#define IRQ_GPIOC	19		/* 0x080000 */
+#define IRQ_GPIOD	20		/* 0x100000 */
+#define IRQ_CommRX	21		/* 0x200000 */
+#define IRQ_CommTX	22		/* 0x400000 */
+#define IRQ_Soft	23		/* 0x800000 */
+
+#define NR_GLBL_IRQS	24
+
+#define IRQ_CHAINED_GPIOA(x)  (NR_GLBL_IRQS + x)
+#define IRQ_CHAINED_GPIOB(x)  (IRQ_CHAINED_GPIOA(32) + x)
+#define IRQ_CHAINED_GPIOC(x)  (IRQ_CHAINED_GPIOB(32) + x)
+#define IRQ_CHAINED_GPIOD(x)  (IRQ_CHAINED_GPIOC(32) + x)
+#define NR_IRQS               IRQ_CHAINED_GPIOD(32)
+
+/* Enable mask for multiplexed interrupts */
+#define IRQ_ENA_MUX	(1<<IRQ_GPIOA) | (1<<IRQ_GPIOB) \
+			| (1<<IRQ_GPIOC) | (1<<IRQ_GPIOD)
+
+
+#elif defined (CONFIG_CPU_H7202)
+
+#define IRQ_PMU		0		/* 0x00000001 */
+#define IRQ_DMA		1		/* 0x00000002 */
+#define IRQ_LCD		2		/* 0x00000004 */
+#define IRQ_SOUND	3		/* 0x00000008 */
+#define IRQ_I2S		4		/* 0x00000010 */
+#define IRQ_USB 	5		/* 0x00000020 */
+#define IRQ_MMC 	6		/* 0x00000040 */
+#define IRQ_RTC 	7		/* 0x00000080 */
+#define IRQ_UART0 	8		/* 0x00000100 */
+#define IRQ_UART1 	9		/* 0x00000200 */
+#define IRQ_UART2 	10		/* 0x00000400 */
+#define IRQ_UART3 	11		/* 0x00000800 */
+#define IRQ_KBD 	12		/* 0x00001000 */
+#define IRQ_PS2 	13		/* 0x00002000 */
+#define IRQ_AIC 	14		/* 0x00004000 */
+#define IRQ_TIMER0 	15		/* 0x00008000 */
+#define IRQ_TIMERX 	16		/* 0x00010000 */
+#define IRQ_WDT 	17		/* 0x00020000 */
+#define IRQ_CAN0 	18		/* 0x00040000 */
+#define IRQ_CAN1 	19		/* 0x00080000 */
+#define IRQ_EXT0 	20		/* 0x00100000 */
+#define IRQ_EXT1 	21		/* 0x00200000 */
+#define IRQ_GPIOA 	22		/* 0x00400000 */
+#define IRQ_GPIOB 	23		/* 0x00800000 */
+#define IRQ_GPIOC 	24		/* 0x01000000 */
+#define IRQ_GPIOD 	25		/* 0x02000000 */
+#define IRQ_GPIOE 	26		/* 0x04000000 */
+#define IRQ_COMMRX 	27		/* 0x08000000 */
+#define IRQ_COMMTX 	28		/* 0x10000000 */
+#define IRQ_SMC 	29		/* 0x20000000 */
+#define IRQ_Soft 	30		/* 0x40000000 */
+#define IRQ_RESERVED1 	31		/* 0x80000000 */
+#define NR_GLBL_IRQS	32
+
+#define NR_TIMERX_IRQS	3
+
+#define IRQ_CHAINED_GPIOA(x)  (NR_GLBL_IRQS + x)
+#define IRQ_CHAINED_GPIOB(x)  (IRQ_CHAINED_GPIOA(32) + x)
+#define IRQ_CHAINED_GPIOC(x)  (IRQ_CHAINED_GPIOB(32) + x)
+#define IRQ_CHAINED_GPIOD(x)  (IRQ_CHAINED_GPIOC(32) + x)
+#define IRQ_CHAINED_GPIOE(x)  (IRQ_CHAINED_GPIOD(32) + x)
+#define IRQ_CHAINED_TIMERX(x) (IRQ_CHAINED_GPIOE(32) + x)
+#define IRQ_TIMER1            (IRQ_CHAINED_TIMERX(0))
+#define IRQ_TIMER2            (IRQ_CHAINED_TIMERX(1))
+#define IRQ_TIMER64B          (IRQ_CHAINED_TIMERX(2))
+
+#define NR_IRQS		(IRQ_CHAINED_TIMERX(NR_TIMERX_IRQS))
+
+/* Enable mask for multiplexed interrupts */
+#define IRQ_ENA_MUX	(1<<IRQ_TIMERX) | (1<<IRQ_GPIOA) | (1<<IRQ_GPIOB) | \
+			(1<<IRQ_GPIOC) 	| (1<<IRQ_GPIOD) | (1<<IRQ_GPIOE) | \
+			(1<<IRQ_TIMERX)
+
+#else
+#error cpu definition mismatch
+#endif
+
+/* decode irq number to register number */
+#define IRQ_TO_REGNO(irq) ((irq - NR_GLBL_IRQS) >> 5)
+#define IRQ_TO_BIT(irq) (1 << ((irq - NR_GLBL_IRQS) % 32))
+
+#endif

include/asm-arm/arch-h720x/memory.h

+/*
+ * linux/include/asm-arm/arch-h720x/memory.h
+ *
+ * Copyright (c) 2000 Jungjun Kim
+ *
+ */
+#ifndef __ASM_ARCH_MEMORY_H
+#define __ASM_ARCH_MEMORY_H
+
+/*
+ * Page offset:
+ *    ( 0xc0000000UL )
+ */
+#define PHYS_OFFSET	(0x40000000UL)
+
+/*
+ * Virtual view <-> DMA view memory address translations
+ * virt_to_bus: Used to translate the virtual address to an
+ *              address suitable to be passed to set_dma_addr
+ * bus_to_virt: Used to convert an address for DMA operations
+ *              to an address that the kernel can use.
+ *
+ * There is something to do here later !, Mar 2000, Jungjun Kim
+ */
+
+#define __virt_to_bus__is_a_macro
+#define __virt_to_bus(x)	__virt_to_phys(x)
+#define __bus_to_virt__is_a_macro
+#define __bus_to_virt(x)	__phys_to_virt(x)
+
+#endif

include/asm-arm/arch-h720x/param.h

+/*
+ * linux/include/asm-arm/arch-h720x/param.h
+ *
+ * Copyright (C) 2000 Jungjun Kim
+ */
+
+#ifndef __ASM_ARCH_PARAM_H
+#define __ASM_ARCH_PARAM_H
+
+#endif

include/asm-arm/arch-h720x/serial.h

+/*
+ * linux/include/asm-arm/arch-h72x/serial.h
+ *
+ * Copyright (C) 2003 Thomas Gleixner <tglx@linutronix.de>
+ *               2003 Robert Schwebel <r.schwebel@pengutronix.de>
+ *
+ * Serial port setup for Hynix boards
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __ASM_ARCH_SERIAL_H
+#define __ASM_ARCH_SERIAL_H
+
+#include <asm/arch/irqs.h>
+
+/*
+ * Standard COM flags
+ */
+#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
+#define RS_TABLE_SIZE
+
+/* Base clock is 3.6864 MHz */
+#define BASE_BAUD       (115200*2)
+#define EXTRA_SERIAL_PORT_DEFNS
+
+/*
+ * Board dependend defines
+ */
+#if defined (CONFIG_CPU_H7201)
+#define BASE_BAUD_P3C 	(115200)
+
+#define STD_SERIAL_PORT_DEFNS \
+	{ \
+	.baud_base	= BASE_BAUD, \
+	.port		= SERIAL0_BASE, \
+	.iomem_base     = (u8*)SERIAL0_BASE, \
+	.io_type        = UPIO_MEM, \
+	.irq		= IRQ_UART0, \
+	.flags		= STD_COM_FLAGS, \
+	.iomem_reg_shift = 2,\
+	}, \
+	{ \
+	.baud_base	= BASE_BAUD, \
+	.port		= SERIAL1_BASE, \
+	.iomem_base     = (u8*)SERIAL1_BASE, \
+	.io_type        = UPIO_MEM, \
+	.irq		= IRQ_UART1, \
+	.flags		= STD_COM_FLAGS, \
+	.iomem_reg_shift = 2,\
+	}
+
+#elif defined (CONFIG_CPU_H7202)
+
+#define STD_SERIAL_PORT_DEFNS \
+	{ \
+	.baud_base	= BASE_BAUD, \
+	.port		= SERIAL0_BASE, \
+	.iomem_base     = (u8*)SERIAL0_BASE, \
+	.io_type        = UPIO_MEM, \
+	.irq		= IRQ_UART0, \
+	.flags		= STD_COM_FLAGS, \
+	.iomem_reg_shift = 2,\
+	}, \
+	{ \
+	.baud_base	= BASE_BAUD, \
+	.port		= SERIAL1_BASE, \
+	.iomem_base     = (u8*)SERIAL1_BASE, \
+	.io_type        = UPIO_MEM, \
+	.irq		= IRQ_UART1, \
+	.flags		= STD_COM_FLAGS, \
+	.iomem_reg_shift = 2,\
+	}, \
+	{ \
+	.baud_base	= BASE_BAUD, \
+	.port		= SERIAL2_BASE, \
+	.iomem_base     = (u8*)SERIAL2_BASE, \
+	.io_type        = UPIO_MEM, \
+	.irq		= IRQ_UART2, \
+	.flags		= STD_COM_FLAGS, \
+	.iomem_reg_shift = 2,\
+	}, \
+	{ \
+	.baud_base	= BASE_BAUD, \
+	.port		= SERIAL3_BASE, \
+	.iomem_base     = (u8*)SERIAL3_BASE, \
+	.io_type        = UPIO_MEM, \
+	.irq		= IRQ_UART3, \
+	.flags		= STD_COM_FLAGS, \
+	.iomem_reg_shift = 2,\
+	}
+
+#else
+#error machine definition mismatch
+#endif
+
+/* __ASM_ARCH_SERIAL_H */
+#endif

include/asm-arm/arch-h720x/system.h

+/*
+ * linux/arch/arm/mach-h720x/system.h
+ *
+ * Copyright (C) 2001-2002 Jungjun Kim, Hynix Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ * linux/include/asm-arm/arch-h720x/system.h
+ *
+ */
+
+#ifndef __ASM_ARCH_SYSTEM_H
+#define __ASM_ARCH_SYSTEM_H
+#include <asm/hardware.h>
+
+static void arch_idle(void)
+{
+	CPU_REG (PMU_BASE, PMU_MODE) = PMU_MODE_IDLE;
+	__asm__ __volatile__(
+	"mov	r0, r0\n\t"
+	"mov	r0, r0");
+}
+
+
+static __inline__ void arch_reset(char mode)
+{
+	CPU_REG (PMU_BASE, PMU_STAT) |= PMU_WARMRESET;
+}
+
+#endif

include/asm-arm/arch-h720x/timex.h

+/*
+ * linux/include/asm-arm/arch-h720x/timex.h
+ * Copyright (C) 2000 Jungjun Kim, Hynix Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_TIMEX
+#define __ASM_ARCH_TIMEX
+
+#define CLOCK_TICK_RATE		3686400
+
+#endif

include/asm-arm/arch-h720x/uncompress.h

+/*
+ * linux/include/asm-arm/arch-h720x/uncompress.h
+ *
+ * Copyright (C) 2001-2002 Jungjun Kim
+ */
+
+#ifndef __ASM_ARCH_UNCOMPRESS_H
+#define __ASM_ARCH_UNCOMPRESS_H
+
+#include <asm/arch/hardware.h>
+
+#define LSR 	0x14
+#define TEMPTY 	0x40
+
+static void putstr(const char *s)
+{
+	char c;
+	volatile unsigned char *p = (volatile unsigned char *)(IO_PHYS+0x20000);
+
+	while ( (c = *s++) != '\0') {
+		/* wait until transmit buffer is empty */
+		while((p[LSR] & TEMPTY) == 0x0);
+		/* write next character */
+		*p = c;
+
+		if(c == '\n') {
+			while((p[LSR] & TEMPTY) == 0x0);
+			*p = '\r';
+		}
+	}
+}
+
+/*
+ * nothing to do
+ */
+#define arch_decomp_setup()
+#define arch_decomp_wdog()
+
+#endif

include/asm-arm/arch-h720x/vmalloc.h

+/*
+ * linux/include/asm-arm/arch-h720x/vmalloc.h
+ */
+
+#ifndef __ARCH_ARM_VMALLOC_H
+#define __ARCH_ARM_VMALLOC_H
+
+/*
+ * Just any arbitrary offset to the start of the vmalloc VM area: the
+ * current 8MB value just means that there will be a 8MB "hole" after the
+ * physical memory until the kernel virtual memory starts.  That means that
+ * any out-of-bounds memory accesses will hopefully be caught.
+ * The vmalloc() routines leaves a hole of 4kB between each vmalloced
+ * area for the same reason. ;)
+ */
+#define VMALLOC_OFFSET	  (8*1024*1024)
+#define VMALLOC_START	  (((unsigned long)high_memory + VMALLOC_OFFSET) & ~(VMALLOC_OFFSET-1))
+#define VMALLOC_VMADDR(x) ((unsigned long)(x))
+#define VMALLOC_END       (PAGE_OFFSET + 0x10000000)
+
+#endif

include/asm-s390/page.h

@@ -162,6 +162,25 @@ typedef struct { unsigned long pgd; } pgd_t;
 #define __pgd(x)        ((pgd_t) { (x) } )
 #define __pgprot(x)     ((pgprot_t) { (x) } )
 
+/* default storage key used for all pages */
+extern unsigned int default_storage_key;
+
+static inline void
+page_set_storage_key(unsigned long addr, unsigned int skey)
+{
+	asm volatile ( "sske %0,%1" : : "d" (skey), "a" (addr) );
+}
+
+static inline unsigned int
+page_get_storage_key(unsigned long addr)
+{
+	unsigned int skey;
+
+	asm volatile ( "iske %0,%1" : "=d" (skey) : "a" (addr), "0" (0) );
+
+	return skey;
+}
+
 #endif /* !__ASSEMBLY__ */
 
 /* to align the pointer to the (next) page boundary */

include/asm-s390/pgtable.h

@@ -597,17 +597,13 @@ ptep_establish(struct vm_area_struct *vma,
  * should therefore only be called if it is not mapped in any
  * address space.
  */
-#define page_test_and_clear_dirty(page)					  \
+#define page_test_and_clear_dirty(_page)				  \
 ({									  \
-	struct page *__page = (page);					  \
+	struct page *__page = (_page);					  \
 	unsigned long __physpage = __pa((__page-mem_map) << PAGE_SHIFT);  \
-	int __skey;							  \
-	asm volatile ("iske %0,%1" : "=d" (__skey) : "a" (__physpage));   \
-	if (__skey & _PAGE_CHANGED) {					  \
-		asm volatile ("sske %0,%1"				  \
-			      : : "d" (__skey & ~_PAGE_CHANGED),	  \
-			          "a" (__physpage));			  \
-	}								  \
+	int __skey = page_get_storage_key(__physpage);			  \
+	if (__skey & _PAGE_CHANGED)					  \
+		page_set_storage_key(__physpage, __skey & ~_PAGE_CHANGED);\
 	(__skey & _PAGE_CHANGED);					  \
 })
 
@@ -655,11 +651,10 @@ static inline pte_t mk_pte_phys(unsigned long physpage, pgprot_t pgprot)
 })
 
 #define SetPageUptodate(_page) \
-	do {								  \
-		struct page *__page = (_page);				  \
-		if (!test_and_set_bit(PG_uptodate, &__page->flags))	  \
-			asm volatile ("sske %0,%1" : : "d" (0),		  \
-			      "a" (__pa((__page-mem_map) << PAGE_SHIFT)));\
+	do {								      \
+		struct page *__page = (_page);				      \
+		if (!test_and_set_bit(PG_uptodate, &__page->flags))	      \
+			page_test_and_clear_dirty(_page);		      \
 	} while (0)
 
 #ifdef __s390x__

include/linux/i2o.h

@@ -28,7 +28,7 @@
 #include <asm/io.h>
 #include <asm/semaphore.h>	/* Needed for MUTEX init macros */
 #include <linux/pci.h>
-#include <asm/dma-mapping.h>
+#include <linux/dma-mapping.h>
 
 /* message queue empty */
 #define I2O_QUEUE_EMPTY		0xffffffff

include/linux/percpu.h

@@ -24,8 +24,8 @@ struct percpu_data {
 
 /* 
  * Use this to get to a cpu's version of the per-cpu object allocated using
- * alloc_percpu.  If you want to get "this cpu's version", maybe you want
- * to use get_cpu_ptr... 
+ * alloc_percpu.  Non-atomic access to the current CPU's version should
+ * probably be combined with get_cpu()/put_cpu().
  */ 
 #define per_cpu_ptr(ptr, cpu)                   \
 ({                                              \

kernel/power/console.c

@@ -11,7 +11,9 @@
 
 static int new_loglevel = 10;
 static int orig_loglevel;
+#ifdef SUSPEND_CONSOLE
 static int orig_fgconsole, orig_kmsg;
+#endif
 
 int pm_prepare_console(void)
 {
@@ -50,6 +52,7 @@ void pm_restore_console(void)
 	acquire_console_sem();
 	set_console(orig_fgconsole);
 	release_console_sem();
+	kmsg_redirect = orig_kmsg;
 #endif
 	return;
 }