arm64: dts: marvell: Add support for Marvell CN9130-DB

Add basic support for the Marvell CN9130 modular development board. It
is based on a CN9130 SoC (one AP807 and one internal CP115), extended
via 2xMoCi interface to possibly add up to two more external CP115
(one located on the main board and the other on the board extension).

Available interfaces:
* AP UART
* AP eMMC
* AP SDHCI (disabled)
* CPO GPIO-0
* CPO GPIO-1
* CP0 CRYPTO-0 (disabled)
* CP0 I2C-0
* CP0 I2C-1
* CP0 SDHCI-0
* CP0 NAND-0
* CP0 SPI-1
* CP0 ETH-0 (SFI with SFP cage not working yet, disabled)
* CP0 ETH-1 (RGMII)
* CP0 ETH-2 (RGMII)
* CP0 SATA-0-1
* CP0 USB3-0 (High-speed only)
* CP0 USB3-1 (High-speed only)
* CP0 PCIe-0 x4
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

arch/arm64/boot/dts/marvell/Makefile

@@ -10,3 +10,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb

arch/arm64/boot/dts/marvell/cn9130-db.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marvell International Ltd.
+ *
+ * Device tree for the CN9130-DB board.
+ */
+
+#include "cn9130.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Marvell Armada CN9130-DB";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		gpio1 = &cp0_gpio1;
+		gpio2 = &cp0_gpio2;
+		i2c0 = &cp0_i2c0;
+		ethernet0 = &cp0_eth0;
+		ethernet1 = &cp0_eth1;
+		ethernet2 = &cp0_eth2;
+		spi1 = &cp0_spi0;
+		spi2 = &cp0_spi1;
+	};
+
+	memory@00000000 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	ap0_reg_sd_vccq: ap0_sd_vccq@0 {
+		compatible = "regulator-gpio";
+		regulator-name = "ap0_sd_vccq";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&expander0 8 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1 3300000 0x0>;
+	};
+
+	cp0_reg_usb3_vbus0: cp0_usb3_vbus@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "cp0-xhci0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	cp0_usb3_0_phy0: cp0_usb3_phy@0 {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&cp0_reg_usb3_vbus0>;
+	};
+
+	cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "cp0-xhci1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	cp0_usb3_0_phy1: cp0_usb3_phy@1 {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&cp0_reg_usb3_vbus1>;
+	};
+
+	cp0_reg_sd_vccq: cp0_sd_vccq@0 {
+		compatible = "regulator-gpio";
+		regulator-name = "cp0_sd_vccq";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&expander0 15 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1
+			  3300000 0x0>;
+	};
+
+	cp0_reg_sd_vcc: cp0_sd_vcc@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "cp0_sd_vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&expander0 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	cp0_sfp_eth0: sfp-eth@0 {
+		compatible = "sff,sfp";
+		i2c-bus = <&cp0_sfpp0_i2c>;
+		los-gpio = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>;
+		/*
+		 * SFP cages are unconnected on early PCBs because of an the I2C
+		 * lanes not being connected. Prevent the port for being
+		 * unusable by disabling the SFP node.
+		 */
+		status = "disabled";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+/* on-board eMMC - U9 */
+&ap_sdhci0 {
+	pinctrl-names = "default";
+	bus-width = <8>;
+	vqmmc-supply = <&ap0_reg_sd_vccq>;
+	status = "okay";
+};
+
+&cp0_crypto {
+	status = "disabled";
+};
+
+&cp0_ethernet {
+	status = "okay";
+};
+
+/* SLM-1521-V2, CON9 */
+&cp0_eth0 {
+	status = "disabled";
+	phy-mode = "10gbase-kr";
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp0_comphy4 0>;
+	managed = "in-band-status";
+	sfp = <&cp0_sfp_eth0>;
+};
+
+/* CON56 */
+&cp0_eth1 {
+	status = "okay";
+	phy = <&phy0>;
+	phy-mode = "rgmii-id";
+};
+
+/* CON57 */
+&cp0_eth2 {
+	status = "okay";
+	phy = <&phy1>;
+	phy-mode = "rgmii-id";
+};
+
+&cp0_gpio1 {
+	status = "okay";
+};
+
+&cp0_gpio2 {
+	status = "okay";
+};
+
+&cp0_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_i2c0_pins>;
+	clock-frequency = <100000>;
+
+	/* U36 */
+	expander0: pca953x@21 {
+		compatible = "nxp,pca9555";
+		pinctrl-names = "default";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0x21>;
+		status = "okay";
+	};
+
+	/* U42 */
+	eeprom0: eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <0x20>;
+	};
+
+	/* U38 */
+	eeprom1: eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <0x20>;
+	};
+};
+
+&cp0_i2c1 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	/* SLM-1521-V2 - U3 */
+	i2c-mux@72 { /* verify address - depends on dpr */
+		compatible = "nxp,pca9544";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x72>;
+		cp0_sfpp0_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* U12 */
+			cp0_module_expander1: pca9555@21 {
+				compatible = "nxp,pca9555";
+				pinctrl-names = "default";
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x21>;
+			};
+
+		};
+	};
+};
+
+&cp0_mdio {
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
+/* U54 */
+&cp0_nand_controller {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_pins &nand_rb>;
+
+	nand@0 {
+		reg = <0>;
+		label = "main-storage";
+		nand-rb = <0>;
+		nand-ecc-mode = "hw";
+		nand-on-flash-bbt;
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "U-Boot";
+				reg = <0 0x200000>;
+			};
+			partition@200000 {
+				label = "Linux";
+				reg = <0x200000 0xd00000>;
+			};
+			partition@1000000 {
+				label = "Filesystem";
+				reg = <0x1000000 0x3f000000>;
+			};
+		};
+	};
+};
+
+/* SLM-1521-V2, CON6 */
+&cp0_pcie0 {
+	status = "okay";
+	num-lanes = <4>;
+	num-viewport = <8>;
+	/* Generic PHY, providing serdes lanes */
+	phys = <&cp0_comphy0 0
+		&cp0_comphy1 0
+		&cp0_comphy2 0
+		&cp0_comphy3 0>;
+};
+
+&cp0_sata0 {
+	status = "okay";
+
+	/* SLM-1521-V2, CON2 */
+	sata-port@1 {
+		status = "okay";
+		/* Generic PHY, providing serdes lanes */
+		phys = <&cp0_comphy5 1>;
+	};
+};
+
+/* CON 28 */
+&cp0_sdhci0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_sdhci_pins
+		     &cp0_sdhci_cd_pins>;
+	bus-width = <4>;
+	cd-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	vqmmc-supply = <&cp0_reg_sd_vccq>;
+	vmmc-supply = <&cp0_reg_sd_vcc>;
+};
+
+/* U55 */
+&cp0_spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_spi0_pins>;
+	reg = <0x700680 0x50>;
+
+	spi-flash@0 {
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		/* On-board MUX does not allow higher frequencies */
+		spi-max-frequency = <40000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "U-Boot-0";
+				reg = <0x0 0x200000>;
+			};
+
+			partition@400000 {
+				label = "Filesystem-0";
+				reg = <0x200000 0xe00000>;
+			};
+		};
+	};
+};
+
+&cp0_syscon0 {
+	cp0_pinctrl: pinctrl {
+		compatible = "marvell,cp115-standalone-pinctrl";
+
+		cp0_i2c0_pins: cp0-i2c-pins-0 {
+			marvell,pins = "mpp37", "mpp38";
+			marvell,function = "i2c0";
+		};
+		cp0_i2c1_pins: cp0-i2c-pins-1 {
+			marvell,pins = "mpp35", "mpp36";
+			marvell,function = "i2c1";
+		};
+		cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 {
+			marvell,pins = "mpp0", "mpp1", "mpp2",
+				       "mpp3", "mpp4", "mpp5",
+				       "mpp6", "mpp7", "mpp8",
+				       "mpp9", "mpp10", "mpp11";
+			marvell,function = "ge0";
+		};
+		cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 {
+			marvell,pins = "mpp44", "mpp45", "mpp46",
+				       "mpp47", "mpp48", "mpp49",
+				       "mpp50", "mpp51", "mpp52",
+				       "mpp53", "mpp54", "mpp55";
+			marvell,function = "ge1";
+		};
+		cp0_sdhci_cd_pins: cp0-sdhci-cd-pins-0 {
+			marvell,pins = "mpp43";
+			marvell,function = "gpio";
+		};
+		cp0_sdhci_pins: cp0-sdhi-pins-0 {
+			marvell,pins = "mpp56", "mpp57", "mpp58",
+				       "mpp59", "mpp60", "mpp61";
+			marvell,function = "sdio";
+		};
+		cp0_spi0_pins: cp0-spi-pins-0 {
+			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+			marvell,function = "spi1";
+		};
+		nand_pins: nand-pins {
+			marvell,pins = "mpp15", "mpp16", "mpp17", "mpp18",
+				       "mpp19", "mpp20", "mpp21", "mpp22",
+				       "mpp23", "mpp24", "mpp25", "mpp26",
+				       "mpp27";
+			marvell,function = "dev";
+		};
+		nand_rb: nand-rb {
+			marvell,pins = "mpp13";
+			marvell,function = "nf";
+		};
+	};
+};
+
+&cp0_usb3_0 {
+	status = "okay";
+	usb-phy = <&cp0_usb3_0_phy0>;
+	phy-names = "usb";
+};
+
+&cp0_usb3_1 {
+	status = "okay";
+	usb-phy = <&cp0_usb3_0_phy1>;
+	phy-names = "usb";
+};