ide: use only ->set_pio_mode method for programming PIO modes (take 2)

Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate()
(the only place which used ->speedproc to program PIO modes) and remove
handling of PIO modes from all ->speedproc implementations.

v2:
* Fix pmac_ide_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Signed-off-by: default avatarBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
parent 0d3be723
......@@ -724,11 +724,6 @@ static int speed_cris_ide(ide_drive_t *drive, const u8 speed)
{
int cyc = 0, dvs = 0, strobe = 0, hold = 0;
if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
cris_set_pio_mode(drive, speed - XFER_PIO_0);
return ide_config_drive_speed(drive, speed);
}
switch(speed)
{
case XFER_UDMA_0:
......
......@@ -398,6 +398,18 @@ int ide_set_xfer_rate(ide_drive_t *drive, u8 rate)
rate = ide_rate_filter(drive, rate);
if (rate >= XFER_PIO_0 && rate <= XFER_PIO_5) {
if (hwif->set_pio_mode)
hwif->set_pio_mode(drive, rate - XFER_PIO_0);
/*
* FIXME: this is incorrect to return zero here but
* since all users of ide_set_xfer_rate() ignore
* the return value it is not a problem currently
*/
return 0;
}
return hwif->speedproc(drive, rate);
}
......
......@@ -177,11 +177,6 @@ static int auide_tune_chipset(ide_drive_t *drive, const u8 speed)
mem_sttime = 0;
mem_stcfg = au_readl(MEM_STCFG2);
if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
au1xxx_set_pio_mode(drive, speed - XFER_PIO_0);
return 0;
}
switch(speed) {
#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
case XFER_MW_DMA_2:
......
......@@ -421,11 +421,6 @@ static int ali15x3_tune_chipset(ide_drive_t *drive, const u8 speed)
if (speed < XFER_PIO_0)
return 1;
if (speed >= XFER_PIO_0 && speed <= XFER_PIO_5) {
ali_tune_pio(drive, speed - XFER_PIO_0);
return ide_config_drive_speed(drive, speed);
}
if (speed == XFER_UDMA_6)
speed1 = 0x47;
......
......@@ -178,11 +178,6 @@ static int atiixp_speedproc(ide_drive_t *drive, const u8 speed)
u16 tmp16;
u8 pio;
if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
atiixp_tune_pio(drive, speed - XFER_PIO_0);
return ide_config_drive_speed(drive, speed);
}
spin_lock_irqsave(&atiixp_lock, flags);
save_mdma_mode[drive->dn] = 0;
......
......@@ -323,14 +323,6 @@ static int cmd64x_tune_chipset(ide_drive_t *drive, const u8 speed)
case XFER_MW_DMA_0:
program_cycle_times(drive, 480, 215);
break;
case XFER_PIO_5:
case XFER_PIO_4:
case XFER_PIO_3:
case XFER_PIO_2:
case XFER_PIO_1:
case XFER_PIO_0:
cmd64x_tune_pio(drive, speed - XFER_PIO_0);
break;
default:
return 1;
}
......
......@@ -66,30 +66,13 @@ static struct pio_clocks cs5520_pio_clocks[]={
{1, 2, 1}
};
static int cs5520_tune_chipset(ide_drive_t *drive, const u8 speed)
static void cs5520_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *pdev = hwif->pci_dev;
int pio = speed;
u8 reg;
int controller = drive->dn > 1 ? 1 : 0;
u8 reg;
switch(speed)
{
case XFER_PIO_4:
case XFER_PIO_3:
case XFER_PIO_2:
case XFER_PIO_1:
case XFER_PIO_0:
pio -= XFER_PIO_0;
break;
default:
pio = 0;
printk(KERN_ERR "cs55x0: bad ide timing.\n");
}
printk("PIO clocking = %d\n", pio);
/* FIXME: if DMA = 1 do we need to set the DMA bit here ? */
/* 8bit CAT/CRT - 8bit command timing for channel */
......@@ -114,12 +97,21 @@ static int cs5520_tune_chipset(ide_drive_t *drive, const u8 speed)
reg |= 1<<((drive->dn&1)+5);
outb(reg, hwif->dma_base + 0x02 + 8*controller);
return ide_config_drive_speed(drive, speed);
(void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
static void cs5520_set_pio_mode(ide_drive_t *drive, const u8 pio)
static int cs5520_tune_chipset(ide_drive_t *drive, const u8 speed)
{
cs5520_tune_chipset(drive, XFER_PIO_0 + pio);
printk(KERN_ERR "cs55x0: bad ide timing.\n");
cs5520_set_pio_mode(drive, 0);
/*
* FIXME: this is incorrect to return zero here but
* since all users of ide_set_xfer_rate() ignore
* the return value it is not a problem currently
*/
return 0;
}
static int cs5520_config_drive_xfer_rate(ide_drive_t *drive)
......
......@@ -163,13 +163,6 @@ static int cs5530_tune_chipset(ide_drive_t *drive, const u8 mode)
case XFER_MW_DMA_0: timings = 0x00077771; break;
case XFER_MW_DMA_1: timings = 0x00012121; break;
case XFER_MW_DMA_2: timings = 0x00002020; break;
case XFER_PIO_4:
case XFER_PIO_3:
case XFER_PIO_2:
case XFER_PIO_1:
case XFER_PIO_0:
cs5530_tunepio(drive, mode - XFER_PIO_0);
return 0;
default:
BUG();
break;
......
......@@ -132,11 +132,6 @@ static int it8213_tune_chipset(ide_drive_t *drive, const u8 speed)
u16 reg4042, reg4a;
u8 reg48, reg54, reg55;
if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
it8213_tune_pio(drive, speed - XFER_PIO_0);
return ide_config_drive_speed(drive, speed);
}
pci_read_config_word(dev, maslave, &reg4042);
pci_read_config_byte(dev, 0x48, &reg48);
pci_read_config_word(dev, 0x4a, &reg4a);
......
......@@ -418,15 +418,6 @@ static int it821x_tune_chipset(ide_drive_t *drive, const u8 speed)
ide_hwif_t *hwif = drive->hwif;
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
switch (speed) {
case XFER_PIO_4:
case XFER_PIO_3:
case XFER_PIO_2:
case XFER_PIO_1:
case XFER_PIO_0:
return it821x_tunepio(drive, speed - XFER_PIO_0);
}
if (itdev->smart == 0) {
switch (speed) {
/* MWDMA tuning is really hard because our MWDMA and PIO
......
......@@ -242,11 +242,6 @@ static int piix_tune_chipset(ide_drive_t *drive, const u8 speed)
u16 reg4042, reg4a;
u8 reg48, reg54, reg55;
if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
piix_tune_pio(drive, speed - XFER_PIO_0);
return ide_config_drive_speed(drive, speed);
}
pci_read_config_word(dev, maslave, &reg4042);
sitre = (reg4042 & 0x4000) ? 1 : 0;
pci_read_config_byte(dev, 0x48, &reg48);
......
......@@ -152,16 +152,6 @@ static int sc1200_tune_chipset(ide_drive_t *drive, const u8 mode)
if (sc1200_set_xfer_mode(drive, mode))
return 1; /* failure */
switch (mode) {
case XFER_PIO_4:
case XFER_PIO_3:
case XFER_PIO_2:
case XFER_PIO_1:
case XFER_PIO_0:
sc1200_tunepio(drive, mode - XFER_PIO_0);
return 0;
}
pci_clock = sc1200_get_pci_clock();
/*
......
......@@ -270,13 +270,6 @@ static int scc_tune_chipset(ide_drive_t *drive, const u8 speed)
case XFER_UDMA_0:
idx = speed - XFER_UDMA_0;
break;
case XFER_PIO_4:
case XFER_PIO_3:
case XFER_PIO_2:
case XFER_PIO_1:
case XFER_PIO_0:
scc_tune_pio(drive, speed - XFER_PIO_0);
return ide_config_drive_speed(drive, speed);
default:
return 1;
}
......
......@@ -157,11 +157,6 @@ static int svwks_tune_chipset(ide_drive_t *drive, const u8 speed)
u8 ultra_enable = 0, ultra_timing = 0, dma_timing = 0;
if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
svwks_tune_pio(drive, speed - XFER_PIO_0);
return ide_config_drive_speed(drive, speed);
}
/* If we are about to put a disk into UDMA mode we screwed up.
Our code assumes we never _ever_ do this on an OSB4 */
......
......@@ -284,13 +284,6 @@ static int siimage_tune_chipset(ide_drive_t *drive, const u8 speed)
scsc = is_sata(hwif) ? 1 : scsc;
switch(speed) {
case XFER_PIO_4:
case XFER_PIO_3:
case XFER_PIO_2:
case XFER_PIO_1:
case XFER_PIO_0:
sil_tune_pio(drive, speed - XFER_PIO_0);
return ide_config_drive_speed(drive, speed);
case XFER_MW_DMA_2:
case XFER_MW_DMA_1:
case XFER_MW_DMA_0:
......
......@@ -519,15 +519,10 @@ static void config_art_rwp_pio (ide_drive_t *drive, u8 pio)
}
}
static int sis5513_tune_drive(ide_drive_t *drive, const u8 pio)
{
config_art_rwp_pio(drive, pio);
return ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
static void sis_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
(void)sis5513_tune_drive(drive, pio);
config_art_rwp_pio(drive, pio);
(void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
static int sis5513_tune_chipset(ide_drive_t *drive, const u8 speed)
......@@ -537,9 +532,6 @@ static int sis5513_tune_chipset(ide_drive_t *drive, const u8 speed)
u32 regdw;
u8 drive_pci, reg;
if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4)
return sis5513_tune_drive(drive, speed - XFER_PIO_0);
/* See config_art_rwp_pio for drive pci config registers */
drive_pci = 0x40;
if (chipset_family >= ATA_133) {
......
......@@ -139,14 +139,6 @@ static int sl82c105_tune_chipset(ide_drive_t *drive, const u8 speed)
pci_write_config_word(dev, reg, drv_ctrl);
}
break;
case XFER_PIO_5:
case XFER_PIO_4:
case XFER_PIO_3:
case XFER_PIO_2:
case XFER_PIO_1:
case XFER_PIO_0:
sl82c105_tune_pio(drive, speed - XFER_PIO_0);
break;
default:
return -1;
}
......
......@@ -110,11 +110,6 @@ static int slc90e66_tune_chipset(ide_drive_t *drive, const u8 speed)
int u_speed = 0, u_flag = 1 << drive->dn;
u16 reg4042, reg44, reg48, reg4a;
if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
slc90e66_tune_pio(drive, speed - XFER_PIO_0);
return ide_config_drive_speed(drive, speed);
}
pci_read_config_word(dev, maslave, &reg4042);
sitre = (reg4042 & 0x4000) ? 1 : 0;
pci_read_config_word(dev, 0x44, &reg44);
......
......@@ -917,7 +917,7 @@ set_timings_mdma(ide_drive_t *drive, int intf_type, u32 *timings, u32 *timings2,
/*
* Speedproc. This function is called by the core to set any of the standard
* timing (PIO, MDMA or UDMA) to both the drive and the controller.
* DMA timing (MDMA or UDMA) to both the drive and the controller.
* You may notice we don't use this function on normal "dma check" operation,
* our dedicated function is more precise as it uses the drive provided
* cycle time value. We should probably fix this one to deal with that too...
......@@ -964,13 +964,6 @@ static int pmac_ide_tune_chipset(ide_drive_t *drive, const u8 speed)
case XFER_SW_DMA_0:
return 1;
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
case XFER_PIO_4:
case XFER_PIO_3:
case XFER_PIO_2:
case XFER_PIO_1:
case XFER_PIO_0:
pmac_ide_set_pio_mode(drive, speed & 0x07);
return 0;
default:
ret = 1;
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment