sparc: Delete bare sbus char bpp driver, obsoleted by parport_sunbpp

Signed-off-by: David S. Miller <davem@davemloft.net>

arch/sparc/include/asm/Kbuild

@@ -22,7 +22,6 @@ header-y += unistd_64.h
 
 header-y += apc.h
 header-y += asi.h
-header-y += bpp.h
 header-y += display7seg.h
 header-y += envctrl.h
 header-y += fbio.h

arch/sparc/include/asm/bpp.h

-#ifndef _SPARC_BPP_H
-#define _SPARC_BPP_H
-
-/*
- * Copyright (c) 1995 Picture Elements
- *	Stephen Williams
- *	Gus Baldauf
- *
- * Linux/SPARC port by Peter Zaitcev.
- * Integration into SPARC tree by Tom Dyas.
- */
-
-#include  <linux/ioctl.h>
-
-/*
- * This is a driver that supports IEEE Std 1284-1994 communications
- * with compliant or compatible devices. It will use whatever features
- * the device supports, prefering those that are typically faster.
- *
- * When the device is opened, it is left in COMPATIBILITY mode, and
- * writes work like any printer device. The driver only attempt to
- * negotiate 1284 modes when needed so that plugs can be pulled,
- * switch boxes switched, etc., without disrupting things. It will
- * also leave the device in compatibility mode when closed.
- */
-
-
-
-/*
- * This driver also supplies ioctls to manually manipulate the
- * pins. This is great for testing devices, or writing code to deal
- * with bizzarro-mode of the ACME Special TurboThingy Plus.
- *
- * NOTE: These ioctl currently do not interact well with
- * read/write. Caveat emptor.
- *
- * PUT_PINS allows us to assign the sense of all the pins, including
- * the data pins if being driven by the host. The GET_PINS returns the
- * pins that the peripheral drives, including data if appropriate.
- */
-
-# define BPP_PUT_PINS _IOW('B', 1, int)
-# define BPP_GET_PINS _IOR('B', 2, char) /* that's bogus - should've been _IO */
-# define BPP_PUT_DATA _IOW('B', 3, int)
-# define BPP_GET_DATA _IOR('B', 4, char) /* ditto */
-
-/*
- * Set the data bus to input mode. Disengage the data bin driver and
- * be prepared to read values from the peripheral. If the arg is 0,
- * then revert the bus to output mode.
- */
-# define BPP_SET_INPUT _IOW('B', 5, int)
-
-/*
- * These bits apply to the PUT operation...
- */
-# define BPP_PP_nStrobe   0x0001
-# define BPP_PP_nAutoFd   0x0002
-# define BPP_PP_nInit     0x0004
-# define BPP_PP_nSelectIn 0x0008
-
-/*
- * These apply to the GET operation, which also reads the current value
- * of the previously put values. A bit mask of these will be returned
- * as a bit mask in the return code of the ioctl().
- */
-# define BPP_GP_nAck   0x0100
-# define BPP_GP_Busy   0x0200
-# define BPP_GP_PError 0x0400
-# define BPP_GP_Select 0x0800
-# define BPP_GP_nFault 0x1000
-
-#endif

arch/sparc/kernel/ebus.c

@@ -20,7 +20,6 @@
 #include <asm/io.h>
 #include <asm/oplib.h>
 #include <asm/prom.h>
-#include <asm/bpp.h>
 
 struct linux_ebus *ebus_chain = NULL;
 

arch/sparc64/kernel/ebus.c

@@ -21,7 +21,6 @@
 #include <asm/ebus.h>
 #include <asm/oplib.h>
 #include <asm/prom.h>
-#include <asm/bpp.h>
 #include <asm/irq.h>
 #include <asm/io.h>
 

drivers/sbus/char/Kconfig

@@ -30,14 +30,6 @@ config OBP_FLASH
 	  The OpenBoot PROM on Ultra systems is flashable. If you want to be
 	  able to upgrade the OBP firmware, say Y here.
 
-config SUN_BPP
-	tristate "Bidirectional parallel port support (OBSOLETE)"
-	depends on EXPERIMENTAL
-	help
-	  Say Y here to support Sun's obsolete variant of IEEE1284
-	  bidirectional parallel port protocol as /dev/bppX.  Can be built on
-	  x86 machines.
-
 config SUN_VIDEOPIX
 	tristate "Videopix Frame Grabber (EXPERIMENTAL)"
 	depends on EXPERIMENTAL && (BROKEN || !64BIT)

drivers/sbus/char/Makefile

@@ -17,7 +17,6 @@ obj-$(CONFIG_WATCHDOG_RIO)		+= riowatchdog.o
 obj-$(CONFIG_OBP_FLASH)			+= flash.o
 obj-$(CONFIG_SUN_OPENPROMIO)		+= openprom.o
 obj-$(CONFIG_SUN_MOSTEK_RTC)		+= rtc.o
-obj-$(CONFIG_SUN_BPP)			+= bpp.o
 obj-$(CONFIG_SUN_VIDEOPIX)		+= vfc.o
 obj-$(CONFIG_TADPOLE_TS102_UCTRL)	+= uctrl.o
 obj-$(CONFIG_SUN_JSFLASH)		+= jsflash.o

drivers/sbus/sbus.c

@@ -14,7 +14,6 @@
 #include <asm/dma.h>
 #include <asm/oplib.h>
 #include <asm/prom.h>
-#include <asm/bpp.h>
 #include <asm/irq.h>
 
 static ssize_t