Skip to content

L
linux
Commit 9bb08254 authored by Maxime Ripard's avatar Maxime Ripard
Browse files
Options

ARM: sun7i: hummingbird: Convert to DT label based syntax 

In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
parent 712a9fa2
Hide whitespace changes
Inline Side-by-side
Showing with 191 additions and 193 deletions
arch/arm/boot/dts/sun7i-a20-hummingbird.dts
View file @ 9bb08254
......@@ -67,199 +67,6 @@ aliases {
serial4 = &uart5;
};
soc@01c00000 {
mmc0: mmc@01c0f000 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <&reg_vcc3v0>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
cd-inverted;
status = "okay";
};
mmc3: mmc@01c12000 {
pinctrl-names = "default";
pinctrl-0 = <&mmc3_pins_a>;
vmmc-supply = <&reg_mmc3_vdd>;
bus-width = <4>;
non-removable;
status = "okay";
};
usbphy: phy@01c13400 {
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb2_vbus>;
status = "okay";
};
ehci0: usb@01c14000 {
status = "okay";
};
ohci0: usb@01c14400 {
status = "okay";
};
ahci: sata@01c18000 {
target-supply = <&reg_ahci_5v>;
status = "okay";
};
ehci1: usb@01c1c000 {
status = "okay";
};
ohci1: usb@01c1c400 {
status = "okay";
};
pio: pinctrl@01c20800 {
ahci_pwr_pin_a20_hummingbird: ahci_pwr_pin@0 {
allwinner,pins = "PH15";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
usb1_vbus_pin_a20_hummingbird: usb1_vbus_pin@0 {
allwinner,pins = "PH2";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
mmc3_vdd_pin_a20_hummingbird: mmc3_vdd_pin@0 {
allwinner,pins = "PH9";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
gmac_vdd_pin_a20_hummingbird: gmac_vdd_pin@0 {
allwinner,pins = "PH16";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
pwm: pwm@01c20e00 {
pinctrl-names = "default";
pinctrl-0 = <&pwm0_pins_a>;
status = "okay";
};
ir0: ir@01c21800 {
pinctrl-names = "default";
pinctrl-0 = <&ir0_pins_a>;
status = "okay";
};
uart0: serial@01c28000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
uart2: serial@01c28800 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins_a>;
status = "okay";
};
uart3: serial@01c28c00 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins_a>;
status = "okay";
};
uart4: serial@01c29000 {
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins_a>;
status = "okay";
};
uart5: serial@01c29400 {
pinctrl-names = "default";
pinctrl-0 = <&uart5_pins_a>;
status = "okay";
};
i2c0: i2c@01c2ac00 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
compatible = "x-powers,axp209";
reg = <0x34>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <1>;
};
};
i2c1: i2c@01c2b000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
i2c2: i2c@01c2b400 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
i2c3: i2c@01c2b800 {
pinctrl-names = "default";
pinctrl-0 = <&i2c3_pins_a>;
status = "okay";
};
spi2: spi@01c17000 {
pinctrl-names = "default";
pinctrl-0 = <&spi2_pins_b>;
status = "okay";
};
gmac: ethernet@01c50000 {
pinctrl-names = "default";
pinctrl-0 = <&gmac_pins_rgmii_a>;
phy = <&phy1>;
phy-mode = "rgmii";
phy-supply = <&reg_gmac_vdd>;
/* phy reset config */
snps,reset-gpio = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */
snps,reset-active-low;
/* wait 1s after reset, otherwise fail to read phy id */
snps,reset-delays-us = <0 10000 1000000>;
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
};
};
};
reg_ahci_5v: ahci-5v {
pinctrl-0 = <&ahci_pwr_pin_a20_hummingbird>;
gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
status = "okay";
};
reg_usb1_vbus: usb1-vbus {
pinctrl-0 = <&usb1_vbus_pin_a20_hummingbird>;
gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
status = "okay";
};
reg_usb2_vbus: usb2-vbus {
status = "okay";
};
reg_mmc3_vdd: mmc3_vdd {
compatible = "regulator-fixed";
pinctrl-names = "default";
......@@ -282,3 +89,194 @@ reg_gmac_vdd: gmac_vdd {
gpio = <&pio 7 16 GPIO_ACTIVE_HIGH>; /* PH16 */
};
};
&ahci {
target-supply = <&reg_ahci_5v>;
status = "okay";
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&gmac {
pinctrl-names = "default";
pinctrl-0 = <&gmac_pins_rgmii_a>;
phy = <&phy1>;
phy-mode = "rgmii";
phy-supply = <&reg_gmac_vdd>;
/* phy reset config */
snps,reset-gpio = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */
snps,reset-active-low;
/* wait 1s after reset, otherwise fail to read phy id */
snps,reset-delays-us = <0 10000 1000000>;
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
};
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
compatible = "x-powers,axp209";
reg = <0x34>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <1>;
};
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
&i2c3 {
pinctrl-names = "default";
pinctrl-0 = <&i2c3_pins_a>;
status = "okay";
};
&ir0 {
pinctrl-names = "default";
pinctrl-0 = <&ir0_pins_a>;
status = "okay";
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <&reg_vcc3v0>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
cd-inverted;
status = "okay";
};
&mmc3 {
pinctrl-names = "default";
pinctrl-0 = <&mmc3_pins_a>;
vmmc-supply = <&reg_mmc3_vdd>;
bus-width = <4>;
non-removable;
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&pio {
ahci_pwr_pin_a20_hummingbird: ahci_pwr_pin@0 {
allwinner,pins = "PH15";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
usb1_vbus_pin_a20_hummingbird: usb1_vbus_pin@0 {
allwinner,pins = "PH2";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
mmc3_vdd_pin_a20_hummingbird: mmc3_vdd_pin@0 {
allwinner,pins = "PH9";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
gmac_vdd_pin_a20_hummingbird: gmac_vdd_pin@0 {
allwinner,pins = "PH16";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm0_pins_a>;
status = "okay";
};
&reg_ahci_5v {
pinctrl-0 = <&ahci_pwr_pin_a20_hummingbird>;
gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
status = "okay";
};
&reg_usb1_vbus {
pinctrl-0 = <&usb1_vbus_pin_a20_hummingbird>;
gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
status = "okay";
};
&reg_usb2_vbus {
status = "okay";
};
&spi2 {
pinctrl-names = "default";
pinctrl-0 = <&spi2_pins_b>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins_a>;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins_a>;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins_a>;
status = "okay";
};
&uart5 {
pinctrl-names = "default";
pinctrl-0 = <&uart5_pins_a>;
status = "okay";
};
&usbphy {
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb2_vbus>;
status = "okay";
};
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7