Commit a0823810 authored by Nick Kossifidis's avatar Nick Kossifidis Committed by John W. Linville

ath5k: Allow user/driver to set txpower

* Now that we have regulatory control enable the driver to set
 txpower on hw

 * Also use txpower table offset so that we can match
 power range set by user/driver with indices on power table.

 Tested 2 different cards (a CM9 and an RF5112-based ubnt) and got
 the same output using a remote machine to measure per-packet rssi
 (conected the cards using attenuators). I also switched between
 various tx power levels and i saw an equal power change on the remote
 machine (so txpower changes as expected) and verified that we have
 the same output on each rate.
Signed-off-by: default avatarNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: default avatarBob Copeland <me@bobcopeland.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
parent 15e46928
......@@ -1100,11 +1100,12 @@ struct ath5k_hw {
/* Values in 0.25dB units */
s16 txp_min_pwr;
s16 txp_max_pwr;
/* Values in 0.5dB units */
s16 txp_offset;
s16 txp_ofdm;
/* Values in dB units */
s16 txp_cck_ofdm_pwr_delta;
s16 txp_cck_ofdm_gainf_delta;
/* Value in dB units */
s16 txp_cck_ofdm_pwr_delta;
} ah_txpower;
struct {
......@@ -1271,7 +1272,7 @@ extern unsigned int ath5k_hw_get_def_antenna(struct ath5k_hw *ah);
extern int ath5k_hw_phy_disable(struct ath5k_hw *ah);
/* TX power setup */
extern int ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel, u8 ee_mode, u8 txpower);
extern int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 ee_mode, u8 txpower);
extern int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 txpower);
/*
* Functions used internaly
......
......@@ -2747,12 +2747,21 @@ static int
ath5k_config(struct ieee80211_hw *hw, u32 changed)
{
struct ath5k_softc *sc = hw->priv;
struct ath5k_hw *ah = sc->ah;
struct ieee80211_conf *conf = &hw->conf;
int ret;
mutex_lock(&sc->lock);
sc->power_level = conf->power_level;
sc->bintval = conf->beacon_int;
if ((changed & IEEE80211_CONF_CHANGE_POWER) &&
(sc->power_level != conf->power_level)) {
sc->power_level = conf->power_level;
/* Half dB steps */
ath5k_hw_set_txpower_limit(ah, (conf->power_level * 2));
}
ret = ath5k_chan_set(sc, conf->channel);
......
......@@ -168,9 +168,6 @@ int ath5k_hw_rfgain_opt_init(struct ath5k_hw *ah)
* tx power and a Peak to Average Power Detector (PAPD) will try
* to measure the gain.
*
* TODO: Use propper tx power setting for the probe packet so
* that we don't observe a serious power drop on the receiver
*
* XXX: How about forcing a tx packet (bypassing PCU arbitrator etc)
* just after we enable the probe so that we don't mess with
* standard traffic ? Maybe it's time to use sw interrupts and
......@@ -186,7 +183,7 @@ static void ath5k_hw_request_rfgain_probe(struct ath5k_hw *ah)
/* Send the packet with 2dB below max power as
* patent doc suggest */
ath5k_hw_reg_write(ah, AR5K_REG_SM(ah->ah_txpower.txp_max_pwr - 4,
ath5k_hw_reg_write(ah, AR5K_REG_SM(ah->ah_txpower.txp_ofdm - 4,
AR5K_PHY_PAPD_PROBE_TXPOWER) |
AR5K_PHY_PAPD_PROBE_TX_NEXT, AR5K_PHY_PAPD_PROBE);
......@@ -2482,8 +2479,19 @@ ath5k_setup_rate_powertable(struct ath5k_hw *ah, u16 max_pwr,
for (i = 8; i <= 15; i++)
rates[i] -= ah->ah_txpower.txp_cck_ofdm_gainf_delta;
ah->ah_txpower.txp_min_pwr = rates[7];
ah->ah_txpower.txp_max_pwr = rates[0];
/* Now that we have all rates setup use table offset to
* match the power range set by user with the power indices
* on PCDAC/PDADC table */
for (i = 0; i < 16; i++) {
rates[i] += ah->ah_txpower.txp_offset;
/* Don't get out of bounds */
if (rates[i] > 63)
rates[i] = 63;
}
/* Min/max in 0.25dB units */
ah->ah_txpower.txp_min_pwr = 2 * rates[7];
ah->ah_txpower.txp_max_pwr = 2 * rates[0];
ah->ah_txpower.txp_ofdm = rates[7];
}
......@@ -2591,16 +2599,37 @@ ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel,
return 0;
}
int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 mode, u8 txpower)
int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 txpower)
{
/*Just a try M.F.*/
struct ieee80211_channel *channel = &ah->ah_current_channel;
u8 ee_mode;
ATH5K_TRACE(ah->ah_sc);
switch (channel->hw_value & CHANNEL_MODES) {
case CHANNEL_A:
case CHANNEL_T:
case CHANNEL_XR:
ee_mode = AR5K_EEPROM_MODE_11A;
break;
case CHANNEL_G:
case CHANNEL_TG:
ee_mode = AR5K_EEPROM_MODE_11G;
break;
case CHANNEL_B:
ee_mode = AR5K_EEPROM_MODE_11B;
break;
default:
ATH5K_ERR(ah->ah_sc,
"invalid channel: %d\n", channel->center_freq);
return -EINVAL;
}
ATH5K_DBG(ah->ah_sc, ATH5K_DEBUG_TXPOWER,
"changing txpower to %d\n", txpower);
return ath5k_hw_txpower(ah, channel, mode, txpower);
return ath5k_hw_txpower(ah, channel, ee_mode, txpower);
}
#undef _ATH5K_PHY
......@@ -1000,7 +1000,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode,
* Set TX power (FIXME)
*/
ret = ath5k_hw_txpower(ah, channel, ee_mode,
AR5K_TUNE_DEFAULT_TXPOWER);
ah->ah_txpower.txp_max_pwr / 2);
if (ret)
return ret;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment