MIPS: Netlogic: Add default DTB for XLP9XX SoC

Add a default device tree fie for XLP9XX boards, and add code to use
this device tree if no DTB is passed to the kernel.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6287/

arch/mips/netlogic/Kconfig

@@ -28,6 +28,15 @@ config DT_XLP_FVP
 	  pointer to the kernel.  The corresponding DTS file is at
 	  arch/mips/netlogic/dts/xlp_fvp.dts
 
+config DT_XLP_GVP
+	bool "Built-in device tree for XLP GVP boards"
+	default y
+	help
+	  Add an FDT blob for XLP GVP board into the kernel.
+	  This DTB will be used if the firmware does not pass in a DTB
+	  pointer to the kernel.  The corresponding DTS file is at
+	  arch/mips/netlogic/dts/xlp_gvp.dts
+
 config NLM_MULTINODE
 	bool "Support for multi-chip boards"
 	depends on NLM_XLP_BOARD

arch/mips/netlogic/dts/Makefile

 obj-$(CONFIG_DT_XLP_EVP) := xlp_evp.dtb.o
 obj-$(CONFIG_DT_XLP_SVP) += xlp_svp.dtb.o
 obj-$(CONFIG_DT_XLP_FVP) += xlp_fvp.dtb.o
+obj-$(CONFIG_DT_XLP_GVP) += xlp_gvp.dtb.o

arch/mips/netlogic/dts/xlp_gvp.dts

+/*
+ * XLP9XX Device Tree Source for GVP boards
+ */
+
+/dts-v1/;
+/ {
+	model = "netlogic,XLP-GVP";
+	compatible = "netlogic,xlp";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	soc {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0 0  0 0x18000000  0x04000000   // PCIe CFG
+			  1 0  0 0x16000000  0x02000000>; // GBU chipselects
+
+		serial0: serial@30000 {
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0 0x112100 0xa00>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clock-frequency = <125000000>;
+			interrupt-parent = <&pic>;
+			interrupts = <17>;
+		};
+		pic: pic@4000 {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+			reg = <0 0x110000 0x200>;
+		};
+
+		nor_flash@1,0 {
+			compatible = "cfi-flash";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			bank-width = <2>;
+			reg = <1 0 0x1000000>;
+
+			partition@0 {
+				label = "x-loader";
+				reg = <0x0 0x100000>; /* 1M */
+				read-only;
+			};
+
+			partition@100000 {
+				label = "u-boot";
+				reg = <0x100000 0x100000>; /* 1M */
+			};
+
+			partition@200000 {
+				label = "kernel";
+				reg = <0x200000 0x500000>; /* 5M */
+			};
+
+			partition@700000 {
+				label = "rootfs";
+				reg = <0x700000 0x800000>; /* 8M */
+			};
+
+			partition@f00000 {
+				label = "env";
+				reg = <0xf00000 0x100000>; /* 1M */
+				read-only;
+			};
+		};
+
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200 rdinit=/sbin/init";
+	};
+};

arch/mips/netlogic/xlp/dt.c

@@ -42,13 +42,18 @@
 #include <asm/prom.h>
 
 extern u32 __dtb_xlp_evp_begin[], __dtb_xlp_svp_begin[],
-	__dtb_xlp_fvp_begin[], __dtb_start[];
+	__dtb_xlp_fvp_begin[], __dtb_xlp_gvp_begin[], __dtb_start[];
 static void *xlp_fdt_blob;
 
 void __init *xlp_dt_init(void *fdtp)
 {
 	if (!fdtp) {
 		switch (current_cpu_data.processor_id & 0xff00) {
+#ifdef CONFIG_DT_XLP_GVP
+		case PRID_IMP_NETLOGIC_XLP9XX:
+			fdtp = __dtb_xlp_gvp_begin;
+			break;
+#endif
 #ifdef CONFIG_DT_XLP_FVP
 		case PRID_IMP_NETLOGIC_XLP2XX:
 			fdtp = __dtb_xlp_fvp_begin;