Merge tag 'for-usb-linus-2012-01-24' of...

Merge tag 'for-usb-linus-2012-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus

Sarah writes:
	USB/xhci: Misc fixes for 3.8.

	Hi Greg,

	Here's six patches for xHCI and the USB core.  There's a couple of
	patches to fix xHCI 1.0 field formats, some memory leaks, dead ports,
	and USB 3.0 remote wakeup disabling.

	All of these are marked for stable.

	I know I owe you some re-works of failed stable patches from my last
	patchset round, but I don't think I'm going to get to them before I head
	off to Linux Conf Australia tomorrow.

	Sarah Sharp

drivers/usb/core/hub.c

@@ -2838,6 +2838,23 @@ void usb_enable_ltm(struct usb_device *udev)
 EXPORT_SYMBOL_GPL(usb_enable_ltm);
 
 #ifdef	CONFIG_USB_SUSPEND
+/*
+ * usb_disable_function_remotewakeup - disable usb3.0
+ * device's function remote wakeup
+ * @udev: target device
+ *
+ * Assume there's only one function on the USB 3.0
+ * device and disable remote wake for the first
+ * interface. FIXME if the interface association
+ * descriptor shows there's more than one function.
+ */
+static int usb_disable_function_remotewakeup(struct usb_device *udev)
+{
+	return usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
+				USB_REQ_CLEAR_FEATURE, USB_RECIP_INTERFACE,
+				USB_INTRF_FUNC_SUSPEND,	0, NULL, 0,
+				USB_CTRL_SET_TIMEOUT);
+}
 
 /*
  * usb_port_suspend - suspend a usb device's upstream port
@@ -2955,12 +2972,19 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg)
 		dev_dbg(hub->intfdev, "can't suspend port %d, status %d\n",
 				port1, status);
 		/* paranoia:  "should not happen" */
-		if (udev->do_remote_wakeup)
-			(void) usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
-				USB_REQ_CLEAR_FEATURE, USB_RECIP_DEVICE,
-				USB_DEVICE_REMOTE_WAKEUP, 0,
-				NULL, 0,
-				USB_CTRL_SET_TIMEOUT);
+		if (udev->do_remote_wakeup) {
+			if (!hub_is_superspeed(hub->hdev)) {
+				(void) usb_control_msg(udev,
+						usb_sndctrlpipe(udev, 0),
+						USB_REQ_CLEAR_FEATURE,
+						USB_RECIP_DEVICE,
+						USB_DEVICE_REMOTE_WAKEUP, 0,
+						NULL, 0,
+						USB_CTRL_SET_TIMEOUT);
+			} else
+				(void) usb_disable_function_remotewakeup(udev);
+
+		}
 
 		/* Try to enable USB2 hardware LPM again */
 		if (udev->usb2_hw_lpm_capable == 1)
@@ -3052,20 +3076,30 @@ static int finish_port_resume(struct usb_device *udev)
 	 * udev->reset_resume
 	 */
 	} else if (udev->actconfig && !udev->reset_resume) {
-		le16_to_cpus(&devstatus);
-		if (devstatus & (1 << USB_DEVICE_REMOTE_WAKEUP)) {
-			status = usb_control_msg(udev,
-					usb_sndctrlpipe(udev, 0),
-					USB_REQ_CLEAR_FEATURE,
+		if (!hub_is_superspeed(udev->parent)) {
+			le16_to_cpus(&devstatus);
+			if (devstatus & (1 << USB_DEVICE_REMOTE_WAKEUP))
+				status = usb_control_msg(udev,
+						usb_sndctrlpipe(udev, 0),
+						USB_REQ_CLEAR_FEATURE,
 						USB_RECIP_DEVICE,
-					USB_DEVICE_REMOTE_WAKEUP, 0,
-					NULL, 0,
-					USB_CTRL_SET_TIMEOUT);
-			if (status)
-				dev_dbg(&udev->dev,
-					"disable remote wakeup, status %d\n",
-					status);
+						USB_DEVICE_REMOTE_WAKEUP, 0,
+						NULL, 0,
+						USB_CTRL_SET_TIMEOUT);
+		} else {
+			status = usb_get_status(udev, USB_RECIP_INTERFACE, 0,
+					&devstatus);
+			le16_to_cpus(&devstatus);
+			if (!status && devstatus & (USB_INTRF_STAT_FUNC_RW_CAP
+					| USB_INTRF_STAT_FUNC_RW))
+				status =
+					usb_disable_function_remotewakeup(udev);
 		}
+
+		if (status)
+			dev_dbg(&udev->dev,
+				"disable remote wakeup, status %d\n",
+				status);
 		status = 0;
 	}
 	return status;

drivers/usb/host/pci-quirks.c

@@ -780,6 +780,7 @@ void usb_enable_xhci_ports(struct pci_dev *xhci_pdev)
 				"defaulting to EHCI.\n");
 		dev_warn(&xhci_pdev->dev,
 				"USB 3.0 devices will work at USB 2.0 speeds.\n");
+		usb_disable_xhci_ports(xhci_pdev);
 		return;
 	}
 

drivers/usb/host/xhci-ring.c

@@ -1698,7 +1698,7 @@ static void handle_port_status(struct xhci_hcd *xhci,
 				faked_port_index + 1);
 		if (slot_id && xhci->devs[slot_id])
 			xhci_ring_device(xhci, slot_id);
-		if (bus_state->port_remote_wakeup && (1 << faked_port_index)) {
+		if (bus_state->port_remote_wakeup & (1 << faked_port_index)) {
 			bus_state->port_remote_wakeup &=
 				~(1 << faked_port_index);
 			xhci_test_and_clear_bit(xhci, port_array,
@@ -2589,6 +2589,8 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 				(trb_comp_code != COMP_STALL &&
 					trb_comp_code != COMP_BABBLE))
 				xhci_urb_free_priv(xhci, urb_priv);
+			else
+				kfree(urb_priv);
 
 			usb_hcd_unlink_urb_from_ep(bus_to_hcd(urb->dev->bus), urb);
 			if ((urb->actual_length != urb->transfer_buffer_length &&
@@ -3108,7 +3110,7 @@ static u32 xhci_v1_0_td_remainder(int running_total, int trb_buff_len,
 	 * running_total.
 	 */
 	packets_transferred = (running_total + trb_buff_len) /
-		usb_endpoint_maxp(&urb->ep->desc);
+		GET_MAX_PACKET(usb_endpoint_maxp(&urb->ep->desc));
 
 	if ((total_packet_count - packets_transferred) > 31)
 		return 31 << 17;
@@ -3642,7 +3644,8 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		td_len = urb->iso_frame_desc[i].length;
 		td_remain_len = td_len;
 		total_packet_count = DIV_ROUND_UP(td_len,
-				usb_endpoint_maxp(&urb->ep->desc));
+				GET_MAX_PACKET(
+					usb_endpoint_maxp(&urb->ep->desc)));
 		/* A zero-length transfer still involves at least one packet. */
 		if (total_packet_count == 0)
 			total_packet_count++;
@@ -3664,9 +3667,11 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 		td = urb_priv->td[i];
 		for (j = 0; j < trbs_per_td; j++) {
 			u32 remainder = 0;
-			field = TRB_TBC(burst_count) | TRB_TLBPC(residue);
+			field = 0;
 
 			if (first_trb) {
+				field = TRB_TBC(burst_count) |
+					TRB_TLBPC(residue);
 				/* Queue the isoc TRB */
 				field |= TRB_TYPE(TRB_ISOC);
 				/* Assume URB_ISO_ASAP is set */

include/uapi/linux/usb/ch9.h

@@ -152,6 +152,12 @@
 #define USB_INTRF_FUNC_SUSPEND_LP	(1 << (8 + 0))
 #define USB_INTRF_FUNC_SUSPEND_RW	(1 << (8 + 1))
 
+/*
+ * Interface status, Figure 9-5 USB 3.0 spec
+ */
+#define USB_INTRF_STAT_FUNC_RW_CAP     1
+#define USB_INTRF_STAT_FUNC_RW         2
+
 #define USB_ENDPOINT_HALT		0	/* IN/OUT will STALL */
 
 /* Bit array elements as returned by the USB_REQ_GET_STATUS request. */