Merge tag 'amlogic-dt64' of...

Merge tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

Pull "Amlogic 64-bit platforms: DT updates for v4.15" from Kevin Hilman:

- new SoC support: A113D
- new boards: Tronsmart Vega S96, Khadas vim2
- reserved memory fixups
- gpio-names cleanups
- MMC cleanups, enable high-speed modes
- misc cleanups

* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  arm64: dts: meson-axg: add initial A113D SoC DT support
  dt-bindings: arm: amlogic: Add Meson AXG binding
  ARM64: dts: meson-gx: remove unnecessary uart compatible
  ARM64: dts: meson-gx: remove unnecessary clocks properties
  ARM64: dts: meson-gxl: Add alternate ARM Trusted Firmware reserved memory zone
  ARM64: dts: meson-gxm: enable HS400 on the vim2
  ARM64: dts: meson-gxbb-nexbox-a95x: Enable USB Nodes
  dt-bindings: arm: amlogic: Add Tronsmart Vega S96 binding
  ARM64: dts: meson-gxm: Add Vega S96 board
  ARM64: dts: meson-gxm: Add support for Khadas VIM2
  ARM64: dts: meson-gxl: Take eMMC data strobe out of eMMC pins
  ARM64: dts: meson-gxl: adjust libretech-cc gpio-line-names
  ARM64: dts: meson-gxl: adjust kvim gpio-line-names
  ARM64: dts: meson-gxbb: adjust odroid-c2 gpio-line-names
  ARM64: dts: meson-gxbb: adjust nanopi-k2 gpio-line-names
  ARM64: dts: meson-gx: adjust gpio-ranges for TEST_N
  ARM64: dts: meson-gx: remove gpio offset
  ARM: dts: meson8: remove gpio offset
  ARM64: dts: meson-gxl-libretech-cc: enable internal phy leds
  ARM64: dts: meson-gxl-libretech-cc: enable saradc

Documentation/devicetree/bindings/arm/amlogic.txt

@@ -41,6 +41,10 @@ Boards with the Amlogic Meson GXM S912 SoC shall have the following properties:
   Required root node property:
     compatible: "amlogic,s912", "amlogic,meson-gxm";
 
+Boards with the Amlogic Meson AXG A113D SoC shall have the following properties:
+  Required root node property:
+    compatible: "amlogic,a113d", "amlogic,meson-axg";
+
 Board compatible values (alphabetically, grouped by SoC):
 
   - "geniatech,atv1200" (Meson6)
@@ -71,8 +75,12 @@ Board compatible values (alphabetically, grouped by SoC):
 
   - "amlogic,q200" (Meson gxm s912)
   - "amlogic,q201" (Meson gxm s912)
+  - "khadas,vim2" (Meson gxm s912)
   - "kingnovel,r-box-pro" (Meson gxm S912)
   - "nexbox,a1" (Meson gxm s912)
+  - "tronsmart,vega-s96" (Meson gxm s912)
+
+  - "amlogic,s400" (Meson axg a113d)
 
 Amlogic Meson Firmware registers Interface
 ------------------------------------------

arch/arm/boot/dts/meson8.dtsi

@@ -146,7 +146,7 @@ gpio_ao: ao-bank@14 {
 			reg-names = "mux", "pull", "gpio";
 			gpio-controller;
 			#gpio-cells = <2>;
-			gpio-ranges = <&pinctrl_aobus 0 120 16>;
+			gpio-ranges = <&pinctrl_aobus 0 0 16>;
 		};
 
 		uart_ao_a_pins: uart_ao_a {

arch/arm/boot/dts/meson8b.dtsi

@@ -130,7 +130,7 @@ gpio_ao: ao-bank@14 {
 			reg-names = "mux", "pull", "gpio";
 			gpio-controller;
 			#gpio-cells = <2>;
-			gpio-ranges = <&pinctrl_aobus 0 130 16>;
+			gpio-ranges = <&pinctrl_aobus 0 0 16>;
 		};
 
 		uart_ao_a_pins: uart_ao_a {

arch/arm64/boot/dts/amlogic/Makefile

+dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb
@@ -15,10 +16,12 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-nexbox-a95x.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxm-khadas-vim2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-nexbox-a1.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-q200.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-q201.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-rbox-pro.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb
 
 always		:= $(dtb-y)
 subdir-y	:= $(dts-dirs)

arch/arm64/boot/dts/amlogic/meson-axg-s400.dts

+/*
+ * Copyright (c) 2017 Amlogic, Inc. All rights reserved.
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+
+/ {
+	compatible = "amlogic,s400", "amlogic,a113d", "amlogic,meson-axg";
+	model = "Amlogic Meson AXG S400 Development Board";
+
+	aliases {
+		serial0 = &uart_AO;
+	};
+};
+
+&uart_AO {
+	status = "okay";
+};

arch/arm64/boot/dts/amlogic/meson-axg.dtsi

+/*
+ * Copyright (c) 2017 Amlogic, Inc. All rights reserved.
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "amlogic,meson-axg";
+
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 16 MiB reserved for Hardware ROM Firmware */
+		hwrom_reserved: hwrom@0 {
+			reg = <0x0 0x0 0x0 0x1000000>;
+			no-map;
+		};
+
+		/* Alternate 3 MiB reserved for ARM Trusted Firmware (BL31) */
+		secmon_reserved: secmon@5000000 {
+			reg = <0x0 0x05000000 0x0 0x300000>;
+			no-map;
+		};
+	};
+
+	cpus {
+		#address-cells = <0x2>;
+		#size-cells = <0x0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x2>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0x0 0x3>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		l2: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	xtal: xtal-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "xtal";
+		#clock-cells = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		cbus: cbus@ffd00000 {
+			compatible = "simple-bus";
+			reg = <0x0 0xffd00000 0x0 0x25000>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x0 0x0 0x0 0xffd00000 0x0 0x25000>;
+
+			uart_A: serial@24000 {
+				compatible = "amlogic,meson-gx-uart", "amlogic,meson-uart";
+				reg = <0x0 0x24000 0x0 0x14>;
+				interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+				status = "disabled";
+			};
+
+			uart_B: serial@23000 {
+				compatible = "amlogic,meson-gx-uart", "amlogic,meson-uart";
+				reg = <0x0 0x23000 0x0 0x14>;
+				interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
+				status = "disabled";
+			};
+		};
+
+		gic: interrupt-controller@ffc01000 {
+			compatible = "arm,gic-400";
+			reg = <0x0 0xffc01000 0 0x1000>,
+			      <0x0 0xffc02000 0 0x2000>,
+			      <0x0 0xffc04000 0 0x2000>,
+			      <0x0 0xffc06000 0 0x2000>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9
+				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+		};
+
+		mailbox: mailbox@ff63dc00 {
+			compatible = "amlogic,meson-gx-mhu", "amlogic,meson-gxbb-mhu";
+			reg = <0 0xff63dc00 0 0x400>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 209 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 210 IRQ_TYPE_EDGE_RISING>;
+			#mbox-cells = <1>;
+		};
+
+		sram: sram@fffc0000 {
+			compatible = "amlogic,meson-axg-sram", "mmio-sram";
+			reg = <0x0 0xfffc0000 0x0 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x0 0xfffc0000 0x20000>;
+
+			cpu_scp_lpri: scp-shmem@0 {
+				compatible = "amlogic,meson-axg-scp-shmem";
+				reg = <0x13000 0x400>;
+			};
+
+			cpu_scp_hpri: scp-shmem@200 {
+				compatible = "amlogic,meson-axg-scp-shmem";
+				reg = <0x13400 0x400>;
+			};
+		};
+
+		aobus: aobus@ff800000 {
+			compatible = "simple-bus";
+			reg = <0x0 0xff800000 0x0 0x100000>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x0 0x0 0x0 0xff800000 0x0 0x100000>;
+
+			uart_AO: serial@3000 {
+				compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart";
+				reg = <0x0 0x3000 0x0 0x18>;
+				interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&xtal>, <&xtal>, <&xtal>;
+				clock-names = "xtal", "pclk", "baud";
+				status = "disabled";
+			};
+
+			uart_AO_B: serial@4000 {
+				compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart";
+				reg = <0x0 0x4000 0x0 0x18>;
+				interrupts = <GIC_SPI 197 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&xtal>, <&xtal>, <&xtal>;
+				clock-names = "xtal", "pclk", "baud";
+				status = "disabled";
+			};
+		};
+	};
+};

arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi

@@ -213,7 +213,7 @@ &sd_emmc_b {
 /* eMMC */
 &sd_emmc_c {
 	status = "okay";
-	pinctrl-0 = <&emmc_pins>;
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
 	pinctrl-1 = <&emmc_clk_gate_pins>;
 	pinctrl-names = "default", "clk-gate";
 

arch/arm64/boot/dts/amlogic/meson-gx.dtsi

@@ -225,18 +225,16 @@ reset: reset-controller@4404 {
 			};
 
 			uart_A: serial@84c0 {
-				compatible = "amlogic,meson-gx-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson-gx-uart";
 				reg = <0x0 0x84c0 0x0 0x14>;
 				interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
-				clocks = <&xtal>;
 				status = "disabled";
 			};
 
 			uart_B: serial@84dc {
-				compatible = "amlogic,meson-gx-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson-gx-uart";
 				reg = <0x0 0x84dc 0x0 0x14>;
 				interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
-				clocks = <&xtal>;
 				status = "disabled";
 			};
 
@@ -279,10 +277,9 @@ pwm_ef: pwm@86c0 {
 			};
 
 			uart_C: serial@8700 {
-				compatible = "amlogic,meson-gx-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson-gx-uart";
 				reg = <0x0 0x8700 0x0 0x14>;
 				interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
-				clocks = <&xtal>;
 				status = "disabled";
 			};
 
@@ -391,14 +388,14 @@ sec_AO: ao-secure@140 {
 			};
 
 			uart_AO: serial@4c0 {
-				compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart";
 				reg = <0x0 0x004c0 0x0 0x14>;
 				interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};
 
 			uart_AO_B: serial@4e0 {
-				compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart";
 				reg = <0x0 0x004e0 0x0 0x14>;
 				interrupts = <GIC_SPI 197 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";

arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts

@@ -183,7 +183,9 @@ &pinctrl_aobus {
 			  "VCCK En", "CON1 Header Pin31",
 			  "I2S Header Pin6", "IR In", "I2S Header Pin7",
 			  "I2S Header Pin3", "I2S Header Pin4",
-			  "I2S Header Pin5", "HDMI CEC", "SYS LED";
+			  "I2S Header Pin5", "HDMI CEC", "SYS LED",
+			  /* GPIO_TEST_N */
+			  "";
 };
 
 &pinctrl_periphs {
@@ -229,11 +231,9 @@ &pinctrl_periphs {
 			  "Bluetooth UART TX", "Bluetooth UART RX",
 			  "Bluetooth UART CTS", "Bluetooth UART RTS",
 			  "", "", "", "WIFI 32K", "Bluetooth Enable",
-			  "Bluetooth WAKE HOST",
+			  "Bluetooth WAKE HOST", "",
 			  /* Bank GPIOCLK */
-			  "", "CON1 Header Pin35", "", "",
-			  /* GPIO_TEST_N */
-			  "";
+			  "", "CON1 Header Pin35", "", "";
 };
 
 &pwm_ef {
@@ -302,7 +302,7 @@ &sd_emmc_b {
 /* eMMC */
 &sd_emmc_c {
 	status = "disabled";
-	pinctrl-0 = <&emmc_pins>;
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
 	pinctrl-1 = <&emmc_clk_gate_pins>;
 	pinctrl-names = "default", "clk-gate";
 

arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts

@@ -88,6 +88,18 @@ button@0 {
 		};
 	};
 
+	usb_pwr: regulator-usb-pwrs {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB_PWR";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	vddio_card: gpio-regulator {
 		compatible = "regulator-gpio";
 
@@ -272,7 +284,7 @@ &sd_emmc_b {
 /* eMMC */
 &sd_emmc_c {
 	status = "okay";
-	pinctrl-0 = <&emmc_pins>;
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
 	pinctrl-1 = <&emmc_clk_gate_pins>;
 	pinctrl-names = "default", "clk-gate";
 
@@ -294,3 +306,20 @@ &uart_AO {
 	pinctrl-0 = <&uart_ao_a_pins>;
 	pinctrl-names = "default";
 };
+
+&usb0_phy {
+	status = "okay";
+	phy-supply = <&usb_pwr>;
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};

arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts

@@ -194,7 +194,9 @@ &pinctrl_aobus {
 			  "USB HUB nRESET", "USB OTG Power En",
 			  "J7 Header Pin2", "IR In", "J7 Header Pin4",
 			  "J7 Header Pin6", "J7 Header Pin5", "J7 Header Pin7",
-			  "HDMI CEC", "SYS LED";
+			  "HDMI CEC", "SYS LED",
+			  /* GPIO_TEST_N */
+			  "";
 };
 
 &pinctrl_periphs {
@@ -233,11 +235,9 @@ &pinctrl_periphs {
 			  "J2 Header Pin12", "J2 Header Pin13",
 			  "J2 Header Pin8", "J2 Header Pin10",
 			  "", "", "", "", "",
-			  "J2 Header Pin11", "", "J2 Header Pin7",
+			  "J2 Header Pin11", "", "J2 Header Pin7", "",
 			  /* Bank GPIOCLK */
-			  "", "", "", "",
-			  /* GPIO_TEST_N */
-			  "";
+			  "", "", "", "";
 };
 
 &saradc {
@@ -271,7 +271,7 @@ &sd_emmc_b {
 /* eMMC */
 &sd_emmc_c {
 	status = "okay";
-	pinctrl-0 = <&emmc_pins>;
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
 	pinctrl-1 = <&emmc_clk_gate_pins>;
 	pinctrl-names = "default", "clk-gate";
 

arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi

@@ -242,7 +242,7 @@ &sd_emmc_b {
 /* eMMC */
 &sd_emmc_c {
 	status = "okay";
-	pinctrl-0 = <&emmc_pins>;
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
 	pinctrl-1 = <&emmc_clk_gate_pins>;
 	pinctrl-names = "default", "clk-gate";
 

arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi

@@ -199,7 +199,7 @@ &sd_emmc_b {
 /* eMMC */
 &sd_emmc_c {
 	status = "okay";
-	pinctrl-0 = <&emmc_pins>;
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
 	pinctrl-1 = <&emmc_clk_gate_pins>;
 	pinctrl-names = "default", "clk-gate";
 

arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi

@@ -379,15 +379,21 @@ gpio: bank@4b0 {
 			reg-names = "mux", "pull", "pull-enable", "gpio";
 			gpio-controller;
 			#gpio-cells = <2>;
-			gpio-ranges = <&pinctrl_periphs 0 14 120>;
+			gpio-ranges = <&pinctrl_periphs 0 0 119>;
 		};
 
 		emmc_pins: emmc {
 			mux {
 				groups = "emmc_nand_d07",
 				       "emmc_cmd",
-				       "emmc_clk",
-				       "emmc_ds";
+				       "emmc_clk";
+				function = "emmc";
+			};
+		};
+
+		emmc_ds_pins: emmc-ds {
+			mux {
+				groups = "emmc_ds";
 				function = "emmc";
 			};
 		};

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts

@@ -141,7 +141,7 @@ &sd_emmc_b {
 /* eMMC */
 &sd_emmc_c {
 	status = "okay";
-	pinctrl-0 = <&emmc_pins>;
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
 	pinctrl-1 = <&emmc_clk_gate_pins>;
 	pinctrl-names = "default", "clk-gate";
 

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts

@@ -122,7 +122,9 @@ &pinctrl_aobus {
 			  "J9 Header Pin33",
 			  "IR In",
 			  "HDMI CEC",
-			  "SYS LED";
+			  "SYS LED",
+			  /* GPIO_TEST_N */
+			  "";
 };
 
 &pinctrl_periphs {
@@ -163,9 +165,7 @@ &pinctrl_periphs {
 			  "WIFI 32K", "Bluetooth Enable",
 			  "Bluetooth WAKE HOST",
 			  /* Bank GPIOCLK */
-			  "", "J9 Header Pin39",
-			  /* GPIO_TEST_N */
-			  "";
+			  "", "J9 Header Pin39";
 };
 
 &pwm_AO_ab {

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts

@@ -96,6 +96,13 @@ vcc_card: regulator-vcc-card {
 		regulator-settling-time-down-us = <50000>;
 	};
 
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
 	vddio_boot: regulator-vddio_boot {
 		compatible = "regulator-fixed";
 		regulator-name = "VDDIO_BOOT";
@@ -121,6 +128,11 @@ &ethmac {
 	status = "okay";
 };
 
+&internal_phy {
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
 &ir {
 	status = "okay";
 	pinctrl-0 = <&remote_input_ao_pins>;
@@ -149,7 +161,9 @@ &pinctrl_aobus {
 			  "7J1 Header Pin12",
 			  "IR In",
 			  "9J3 Switch HDMI CEC/7J1 Header Pin11",
-			  "7J1 Header Pin13";
+			  "7J1 Header Pin13",
+			  /* GPIO_TEST_N */
+			  "7J1 Header Pin15";
 };
 
 &pinctrl_periphs {
@@ -191,9 +205,12 @@ &pinctrl_periphs {
 			  "7J1 Header Pin32", "7J1 Header Pin29",
 			  "7J1 Header Pin31",
 			  /* Bank GPIOCLK */
-			  "7J1 Header Pin7", "",
-			  /* GPIO_TEST_N */
-			  "7J1 Header Pin15";
+			  "7J1 Header Pin7", "";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
 };
 
 /* SD card */
@@ -221,7 +238,7 @@ &sd_emmc_b {
 /* eMMC */
 &sd_emmc_c {
 	status = "okay";
-	pinctrl-0 = <&emmc_pins>;
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
 	pinctrl-1 = <&emmc_clk_gate_pins>;
 	pinctrl-names = "default", "clk-gate";
 

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts

@@ -229,7 +229,7 @@ &sd_emmc_b {
 /* eMMC */
 &sd_emmc_c {
 	status = "okay";
-	pinctrl-0 = <&emmc_pins>;
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
 	pinctrl-1 = <&emmc_clk_gate_pins>;
 	pinctrl-names = "default", "clk-gate";
 

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi

@@ -135,7 +135,7 @@ &sd_emmc_b {
 /* eMMC */
 &sd_emmc_c {
 	status = "okay";
-	pinctrl-0 = <&emmc_pins>;
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
 	pinctrl-1 = <&emmc_clk_gate_pins>;
 	pinctrl-names = "default", "clk-gate";
 

arch/arm64/boot/dts/amlogic/meson-gxl.dtsi

@@ -49,6 +49,14 @@
 
 / {
 	compatible = "amlogic,meson-gxl";
+
+	reserved-memory {
+		/* Alternate 3 MiB reserved for ARM Trusted Firmware (BL31) */
+		secmon_reserved_alt: secmon@5000000 {
+			reg = <0x0 0x05000000 0x0 0x300000>;
+			no-map;
+		};
+	};
 };
 
 &ethmac {
@@ -268,15 +276,21 @@ gpio: bank@4b0 {
 			reg-names = "mux", "pull", "pull-enable", "gpio";
 			gpio-controller;
 			#gpio-cells = <2>;
-			gpio-ranges = <&pinctrl_periphs 0 10 101>;
+			gpio-ranges = <&pinctrl_periphs 0 0 100>;
 		};
 
 		emmc_pins: emmc {
 			mux {
 				groups = "emmc_nand_d07",
 				       "emmc_cmd",
-				       "emmc_clk",
-				       "emmc_ds";
+				       "emmc_clk";
+				function = "emmc";
+			};
+		};
+
+		emmc_ds_pins: emmc-ds {
+			mux {
+				groups = "emmc_ds";
 				function = "emmc";
 			};
 		};

arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts

+/*
+ * Copyright (c) 2017 Martin Blumenstingl <martin.blumenstingl@googlemail.com>.
+ * Copyright (c) 2017 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "meson-gxm.dtsi"
+
+/ {
+	compatible = "khadas,vim2", "amlogic,s912", "amlogic,meson-gxm";
+	model = "Khadas VIM2";
+
+	aliases {
+		serial0 = &uart_AO;
+		serial1 = &uart_A;
+		serial2 = &uart_AO_B;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	adc-keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 0>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1710000>;
+
+		button-function {
+			label = "Function";
+			linux,code = <KEY_FN>;
+			press-threshold-microvolt = <10000>;
+		};
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	gpio_fan: gpio-fan {
+		compatible = "gpio-fan";
+		gpios = <&gpio GPIODV_14 GPIO_ACTIVE_HIGH
+			 &gpio GPIODV_15 GPIO_ACTIVE_HIGH>;
+		/* Dummy RPM values since fan is optional */
+		gpio-fan,speed-map = <0 0
+				      1 1
+				      2 2
+				      3 3>;
+		cooling-min-level = <0>;
+		cooling-max-level = <3>;
+		#cooling-cells = <2>;
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <100>;
+
+		button@0 {
+			label = "power";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	pwmleds {
+		compatible = "pwm-leds";
+
+		power {
+			label = "vim:red:power";
+			pwms = <&pwm_AO_ab 1 7812500 0>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <250>; /* milliseconds */
+			polling-delay = <1000>; /* milliseconds */
+
+			thermal-sensors = <&scpi_sensors 0>;
+
+			trips {
+				cpu_alert0: cpu-alert0 {
+					temperature = <70000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "active";
+				};
+
+				cpu_alert1: cpu-alert1 {
+					temperature = <80000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device = <&gpio_fan THERMAL_NO_LIMIT 1>;
+				};
+
+				map1 {
+					trip = <&cpu_alert1>;
+					cooling-device = <&gpio_fan 2 THERMAL_NO_LIMIT>;
+				};
+
+				map2 {
+					trip = <&cpu_alert1>;
+					cooling-device =
+						<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map3 {
+					trip = <&cpu_alert1>;
+					cooling-device =
+						<&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cpu0 {
+	cooling-min-level = <0>;
+	cooling-max-level = <6>;
+	#cooling-cells = <2>;
+};
+
+&cpu4 {
+	cooling-min-level = <0>;
+	cooling-max-level = <4>;
+	#cooling-cells = <2>;
+};
+
+&ethmac {
+	pinctrl-0 = <&eth_pins>;
+	pinctrl-names = "default";
+
+	/* Select external PHY by default */
+	phy-handle = <&external_phy>;
+
+	amlogic,tx-delay-ns = <2>;
+
+	/* External PHY reset is shared with internal PHY Led signals */
+	snps,reset-gpio = <&gpio GPIOZ_14 0>;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-active-low;
+
+	/* External PHY is in RGMII */
+	phy-mode = "rgmii";
+
+	status = "okay";
+};
+
+&external_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */
+		reg = <0>;
+	};
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&i2c_A {
+	status = "okay";
+	pinctrl-0 = <&i2c_a_pins>;
+	pinctrl-names = "default";
+};
+
+&i2c_B {
+	status = "okay";
+	pinctrl-0 = <&i2c_b_pins>;
+	pinctrl-names = "default";
+
+	rtc: rtc@51 {
+		/* has to be enabled manually when a battery is connected: */
+		status = "disabled";
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xin32k";
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+	linux,rc-map-name = "rc-geekbox";
+};
+
+&pwm_AO_ab {
+	status = "okay";
+	pinctrl-0 = <&pwm_ao_a_3_pins>, <&pwm_ao_b_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>, <&pwm_f_clk_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <8>;
+	cap-sd-highspeed;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/*
+ * EMMC_DS pin is shared between SPI NOR CS and eMMC Data Strobe
+ * Remove emmc_ds_pins from sd_emmc_c pinctrl-0 then spifc can be enabled
+ */
+&spifc {
+	status = "disabled";
+	pinctrl-0 = <&nor_pins>;
+	pinctrl-names = "default";
+
+	w25q32: spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q16", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <3000000>;
+	};
+};
+
+/* This one is connected to the Bluetooth module */
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* This is brought out on the Linux_RX (18) and Linux_TX (19) pins: */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* This is brought out on the UART_RX_AO_B (15) and UART_TX_AO_B (16) pins: */
+&uart_AO_B {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_b_pins>;
+	pinctrl-names = "default";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};

arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts

@@ -193,7 +193,7 @@ &sd_emmc_b {
 /* eMMC */
 &sd_emmc_c {
 	status = "okay";
-	pinctrl-0 = <&emmc_pins>;
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
 	pinctrl-1 = <&emmc_clk_gate_pins>;
 	pinctrl-names = "default", "clk-gate";
 

arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts

@@ -216,7 +216,7 @@ &sd_emmc_b {
 /* eMMC */
 &sd_emmc_c {
 	status = "okay";
-	pinctrl-0 = <&emmc_pins>;
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
 	pinctrl-names = "default";
 
 	bus-width = <8>;

arch/arm64/boot/dts/amlogic/meson-gxm-vega-s96.dts

+/*
+ * Copyright (c) 2017 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Copyright (c) 2017 Oleg <balbes-150@yandex.ru>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+/dts-v1/;
+
+#include "meson-gxm.dtsi"
+#include "meson-gx-p23x-q20x.dtsi"
+
+/ {
+	compatible = "tronsmart,vega-s96", "amlogic,s912", "amlogic,meson-gxm";
+	model = "Tronsmart Vega S96";
+
+};
+
+&ethmac {
+	pinctrl-0 = <&eth_pins>;
+	pinctrl-names = "default";
+
+	/* Select external PHY by default */
+	phy-handle = <&external_phy>;
+
+	amlogic,tx-delay-ns = <2>;
+
+	/* External PHY is in RGMII */
+	phy-mode = "rgmii";
+};
+
+&external_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */
+		reg = <0>;
+	};
+};