Merge tag 'imx-dt64-5.7' of...

Merge tag 'imx-dt64-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt

i.MX arm64 DTS update for 5.7:

 - New support for Kontron LS1028A based boards and NXP i.MX8MP EVK.
 - Add Ethernet PHY reset GPIO for imx8mm-evk and imx8mq-evk board.
 - Add gpio-fan, thermal and Ethernet support for imx8mq-phanbell board.
 - Add SNVS clock description to pwrkey device for i.MX8 SoCs.
 - A number of updates on librem5-devkit board to add audio, proximity
   sensor, lsm9ds1 mount matrix support, and improve WoWWAN, DVFS, SD
   devices as well.
 - A series of patches from Anson Huang to update i.MX8 EVK boards
   for support of I2C PCA6416, thermal, GPIO LED, OPP table etc.
 - Add PCIe device nodes for LX2160A and LS1028A SoC.
 - Add FSPI deivce support for LX2160A evaluation boards.
 - Add EEPROM and LTC3882 regulator support for lx2160a-cex7 board.
 - Other small and random updates on LS1028A and i.MX8 support.

* tag 'imx-dt64-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (63 commits)
  arm64: dts: ls1028a: disable the felix switch by default
  arm64: dts: imx8mp: Add snvs clock to powerkey
  arm64: dts: imx8mn: Add snvs clock to powerkey
  arm64: dts: ls1028a: Add PCIe controller DT nodes
  arm64: dts: ls1028a: sl28: add support for variant 2
  arm64: dts: ls1028a: sl28: expose switch ports in KBox A-230-LS
  arm64: dts: ls1028a: sl28: fix on-board EEPROMS
  arm64: dts: freescale: sl28: add SPI flash
  arm64: dts: imx8m: fix aips dts node
  arm64: dts: imx8mn: Add CPU thermal zone support
  arm64: dts: imx8mm: Add thermal zone support
  arm64: dts: imx8mq-phanbell: Fix Ethernet PHY post-reset duration
  arm64: dts: enable fspi in imx8mm dts
  arm64: dts: imx8mn: align name for crypto child nodes
  arm64: dts: lx2160aqds: Add FSPI node properties
  arm64: dts: lx2160ardb: Update FSPI node properties
  arm64: dts: imx8mq-phanbell: Add gpio-fan/thermal support
  arm64: dts: layerscape: add iommu-map property to pci nodes
  arm64: dts: imx8mp-evk: Enable pca6416 on i2c3 bus
  arm64: dts: imx8mp-evk: Add i2c3 support
  ...

Link: https://lore.kernel.org/r/20200318051918.32579-5-shawnguo@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm64/boot/dts/freescale/Makefile

@@ -4,6 +4,11 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frwy.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-oxalis.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-kbox-a-230-ls.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-sl28.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-sl28-var2.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-sl28-var3-ads2.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-sl28-var4.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
@@ -26,6 +31,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb

arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts

+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Device Tree File for the Kontron KBox A-230-LS.
+ *
+ * This consists of a Kontron SMARC-sAL28 (Dual PHY) and a special
+ * carrier (s1914).
+ *
+ * Copyright (C) 2019 Michael Walle <michael@walle.cc>
+ *
+ */
+
+/dts-v1/;
+#include "fsl-ls1028a-kontron-sl28-var4.dts"
+
+/ {
+	model = "Kontron KBox A-230-LS";
+	compatible = "kontron,kbox-a-230-ls", "kontron,sl28-var4",
+		     "kontron,sl28", "fsl,ls1028a";
+};
+
+&enetc_mdio_pf3 {
+	/* BCM54140 QSGMII quad PHY */
+	qsgmii_phy0: ethernet-phy@7 {
+		reg = <7>;
+	};
+
+	qsgmii_phy1: ethernet-phy@8 {
+		reg = <8>;
+	};
+
+	qsgmii_phy2: ethernet-phy@9 {
+		reg = <9>;
+	};
+
+	qsgmii_phy3: ethernet-phy@10 {
+		reg = <10>;
+	};
+};
+
+&enetc_port2 {
+	status = "okay";
+};
+
+&i2c3 {
+	eeprom@57 {
+		compatible = "atmel,24c32";
+		reg = <0x57>;
+		pagesize = <32>;
+	};
+};
+
+&mscc_felix {
+	status = "okay";
+};
+
+&mscc_felix_port0 {
+	label = "swp0";
+	managed = "in-band-status";
+	phy-handle = <&qsgmii_phy0>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&mscc_felix_port1 {
+	label = "swp1";
+	managed = "in-band-status";
+	phy-handle = <&qsgmii_phy1>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&mscc_felix_port2 {
+	label = "swp2";
+	managed = "in-band-status";
+	phy-handle = <&qsgmii_phy2>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&mscc_felix_port3 {
+	label = "swp3";
+	managed = "in-band-status";
+	phy-handle = <&qsgmii_phy3>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&mscc_felix_port4 {
+	ethernet = <&enetc_port2>;
+	status = "okay";
+};

arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts

+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Device Tree file for the Kontron SMARC-sAL28 board.
+ *
+ * This is for the network variant 2 which has two ethernet ports. These
+ * ports are connected to the internal switch.
+ *
+ * Copyright (C) 2020 Michael Walle <michael@walle.cc>
+ *
+ */
+
+/dts-v1/;
+#include "fsl-ls1028a-kontron-sl28.dts"
+
+/ {
+	model = "Kontron SMARC-sAL28 (TSN-on-module)";
+	compatible = "kontron,sl28-var2", "kontron,sl28", "fsl,ls1028a";
+};
+
+&enetc_mdio_pf3 {
+	phy0: ethernet-phy@5 {
+		reg = <0x5>;
+		eee-broken-1000t;
+		eee-broken-100tx;
+	};
+
+	phy1: ethernet-phy@4 {
+		reg = <0x4>;
+		eee-broken-1000t;
+		eee-broken-100tx;
+	};
+};
+
+&enetc_port0 {
+	status = "disabled";
+	/*
+	 * In the base device tree the PHY was registered in the mdio
+	 * subnode as it is PHY for this port. On this module this PHY
+	 * is connected to a switch port instead and registered above.
+	 * Therefore, delete the mdio subnode as well as the phy-handle
+	 * property here.
+	 */
+	/delete-property/ phy-handle;
+	/delete-node/ mdio;
+};
+
+&enetc_port2 {
+	status = "okay";
+};
+
+&mscc_felix {
+	status = "okay";
+};
+
+&mscc_felix_port0 {
+	label = "gbe0";
+	phy-handle = <&phy0>;
+	phy-mode = "sgmii";
+	status = "okay";
+};
+
+&mscc_felix_port1 {
+	label = "gbe1";
+	phy-handle = <&phy1>;
+	phy-mode = "sgmii";
+	status = "okay";
+};
+
+&mscc_felix_port4 {
+	ethernet = <&enetc_port2>;
+	status = "okay";
+};

arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts

+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Device Tree file for the Kontron SMARC-sAL28 board on a SMARC Eval 2.0
+ * carrier (ADS2).
+ *
+ * Copyright (C) 2019 Michael Walle <michael@walle.cc>
+ *
+ */
+
+/dts-v1/;
+#include "fsl-ls1028a-kontron-sl28.dts"
+
+/ {
+	model = "Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier";
+	compatible = "kontron,sl28-var3-ads2", "kontron,sl28-var3",
+		     "kontron,sl28", "fsl,ls1028a";
+
+	sound {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "simple-audio-card";
+		simple-audio-card,widgets =
+			"Headphone", "Headphone Jack",
+			"Line", "Line Out Jack",
+			"Microphone", "Microphone Jack",
+			"Line", "Line In Jack";
+		simple-audio-card,routing =
+			"Line Out Jack", "LINEOUTR",
+			"Line Out Jack", "LINEOUTL",
+			"Headphone Jack", "HPOUTR",
+			"Headphone Jack", "HPOUTL",
+			"IN1L", "Line In Jack",
+			"IN1R", "Line In Jack",
+			"Microphone Jack", "MICBIAS",
+			"IN2L", "Microphone Jack",
+			"IN2R", "Microphone Jack";
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,dai-link@0 {
+			reg = <0>;
+			bitclock-master = <&dailink0_master>;
+			frame-master = <&dailink0_master>;
+			format = "i2s";
+
+			cpu {
+				sound-dai = <&sai6>;
+			};
+
+			dailink0_master: codec {
+				sound-dai = <&wm8904>;
+			};
+		};
+
+		simple-audio-card,dai-link@1 {
+			reg = <1>;
+			bitclock-master = <&dailink1_master>;
+			frame-master = <&dailink1_master>;
+			format = "i2s";
+
+			cpu {
+				sound-dai = <&sai5>;
+			};
+
+			dailink1_master: codec {
+				sound-dai = <&wm8904>;
+			};
+		};
+	};
+};
+
+&dspi2 {
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		m25p,fast-read;
+		spi-max-frequency = <100000000>;
+		reg = <0>;
+	};
+};
+
+&i2c3 {
+	eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <32>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	wm8904: audio-codec@1a {
+		#sound-dai-cells = <0>;
+		compatible = "wlf,wm8904";
+		reg = <0x1a>;
+		clocks = <&mclk>;
+		clock-names = "mclk";
+		assigned-clocks = <&mclk>;
+		assigned-clock-rates = <1250000>;
+	};
+};
+
+&sai5 {
+	status = "okay";
+};
+
+&sai6 {
+	status = "okay";
+};
+
+&soc {
+	mclk: clock-mclk@f130080 {
+		compatible = "fsl,vf610-sai-clock";
+		reg = <0x0 0xf130080 0x0 0x80>;
+		clocks = <&clockgen 4 1>;
+		#clock-cells = <0>;
+	};
+};

arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var4.dts

+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Device Tree file for the Kontron SMARC-sAL28 board.
+ *
+ * This is for the network variant 4 which has two ethernet ports. It
+ * extends the base and provides one more port connected via RGMII.
+ *
+ * Copyright (C) 2019 Michael Walle <michael@walle.cc>
+ *
+ */
+
+/dts-v1/;
+#include "fsl-ls1028a-kontron-sl28.dts"
+#include <dt-bindings/net/qca-ar803x.h>
+
+/ {
+	model = "Kontron SMARC-sAL28 (Dual PHY)";
+	compatible = "kontron,sl28-var4", "kontron,sl28", "fsl,ls1028a";
+};
+
+&enetc_port1 {
+	phy-handle = <&phy1>;
+	phy-connection-type = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy1: ethernet-phy@4 {
+			reg = <0x4>;
+			eee-broken-1000t;
+			eee-broken-100tx;
+
+			qca,clk-out-frequency = <125000000>;
+			qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
+
+			vddio-supply = <&vddh>;
+
+			vddio: vddio-regulator {
+				regulator-name = "VDDIO";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vddh: vddh-regulator {
+				regulator-name = "VDDH";
+			};
+		};
+	};
+};

arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts

+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Device Tree file for the Kontron SMARC-sAL28 board.
+ *
+ * Copyright (C) 2019 Michael Walle <michael@walle.cc>
+ *
+ */
+
+/dts-v1/;
+#include "fsl-ls1028a.dtsi"
+
+/ {
+	model = "Kontron SMARC-sAL28";
+	compatible = "kontron,sl28", "fsl,ls1028a";
+
+	aliases {
+		crypto = &crypto;
+		serial0 = &duart0;
+		serial1 = &duart1;
+		spi0 = &fspi;
+		spi1 = &dspi2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&dspi2 {
+	status = "okay";
+};
+
+&duart0 {
+	status = "okay";
+};
+
+&duart1 {
+	status = "okay";
+};
+
+&enetc_port0 {
+	phy-handle = <&phy0>;
+	phy-connection-type = "sgmii";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@5 {
+			reg = <0x5>;
+			eee-broken-1000t;
+			eee-broken-100tx;
+		};
+	};
+};
+
+&esdhc {
+	sd-uhs-sdr104;
+	sd-uhs-sdr50;
+	sd-uhs-sdr25;
+	sd-uhs-sdr12;
+	status = "okay";
+};
+
+&esdhc1 {
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	bus-width = <8>;
+	status = "okay";
+};
+
+&fspi {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		m25p,fast-read;
+		spi-max-frequency = <133000000>;
+		reg = <0>;
+		/* The following setting enables 1-1-2 (CMD-ADDR-DATA) mode */
+		spi-rx-bus-width = <2>; /* 2 SPI Rx lines */
+		spi-tx-bus-width = <1>; /* 1 SPI Tx line */
+
+		partition@0 {
+			reg = <0x000000 0x010000>;
+			label = "rcw";
+			read-only;
+		};
+
+		partition@10000 {
+			reg = <0x010000 0x0f0000>;
+			label = "failsafe bootloader";
+			read-only;
+		};
+
+		partition@100000 {
+			reg = <0x100000 0x040000>;
+			label = "failsafe DP firmware";
+			read-only;
+		};
+
+		partition@140000 {
+			reg = <0x140000 0x0a0000>;
+			label = "failsafe trusted firmware";
+			read-only;
+		};
+
+		partition@1e0000 {
+			reg = <0x1e0000 0x020000>;
+			label = "reserved";
+			read-only;
+		};
+
+		partition@200000 {
+			reg = <0x200000 0x010000>;
+			label = "configuration store";
+		};
+
+		partition@210000 {
+			reg = <0x210000 0x0f0000>;
+			label = "bootloader";
+		};
+
+		partition@300000 {
+			reg = <0x300000 0x040000>;
+			label = "DP firmware";
+		};
+
+		partition@340000 {
+			reg = <0x340000 0x0a0000>;
+			label = "trusted firmware";
+		};
+
+		partition@3e0000 {
+			reg = <0x3e0000 0x020000>;
+			label = "bootloader environment";
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "TDO", "TCK",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "TMS", "TDI",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c0 {
+	status = "okay";
+
+	rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+};

arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts

@@ -225,6 +225,7 @@ mux: mux-controller {
 &enetc_port1 {
 	phy-handle = <&qds_phy1>;
 	phy-connection-type = "rgmii-id";
+	status = "okay";
 };
 
 &sai1 {

arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts

@@ -177,9 +177,29 @@ &duart1 {
 	status = "okay";
 };
 
+&enetc_mdio_pf3 {
+	/* VSC8514 QSGMII quad PHY */
+	qsgmii_phy0: ethernet-phy@10 {
+		reg = <0x10>;
+	};
+
+	qsgmii_phy1: ethernet-phy@11 {
+		reg = <0x11>;
+	};
+
+	qsgmii_phy2: ethernet-phy@12 {
+		reg = <0x12>;
+	};
+
+	qsgmii_phy3: ethernet-phy@13 {
+		reg = <0x13>;
+	};
+};
+
 &enetc_port0 {
 	phy-handle = <&sgmii_phy0>;
 	phy-connection-type = "sgmii";
+	status = "okay";
 
 	mdio {
 		#address-cells = <1>;
@@ -190,8 +210,49 @@ sgmii_phy0: ethernet-phy@2 {
 	};
 };
 
-&enetc_port1 {
-	status = "disabled";
+&enetc_port2 {
+	status = "okay";
+};
+
+&mscc_felix {
+	status = "okay";
+};
+
+&mscc_felix_port0 {
+	label = "swp0";
+	managed = "in-band-status";
+	phy-handle = <&qsgmii_phy0>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&mscc_felix_port1 {
+	label = "swp1";
+	managed = "in-band-status";
+	phy-handle = <&qsgmii_phy1>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&mscc_felix_port2 {
+	label = "swp2";
+	managed = "in-band-status";
+	phy-handle = <&qsgmii_phy2>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&mscc_felix_port3 {
+	label = "swp3";
+	managed = "in-band-status";
+	phy-handle = <&qsgmii_phy3>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&mscc_felix_port4 {
+	ethernet = <&enetc_port2>;
+	status = "okay";
 };
 
 &sai4 {

arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi

@@ -290,6 +290,45 @@ fspi: spi@20c0000 {
 			status = "disabled";
 		};
 
+		dspi0: spi@2100000 {
+			compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2100000 0x0 0x10000>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "dspi";
+			clocks = <&clockgen 4 1>;
+			spi-num-chipselects = <4>;
+			little-endian;
+			status = "disabled";
+		};
+
+		dspi1: spi@2110000 {
+			compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2110000 0x0 0x10000>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "dspi";
+			clocks = <&clockgen 4 1>;
+			spi-num-chipselects = <4>;
+			little-endian;
+			status = "disabled";
+		};
+
+		dspi2: spi@2120000 {
+			compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2120000 0x0 0x10000>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "dspi";
+			clocks = <&clockgen 4 1>;
+			spi-num-chipselects = <3>;
+			little-endian;
+			status = "disabled";
+		};
+
 		esdhc: mmc@2140000 {
 			compatible = "fsl,ls1028a-esdhc", "fsl,esdhc";
 			reg = <0x0 0x2140000 0x0 0x10000>;
@@ -411,6 +450,60 @@ sata: sata@3200000 {
 			status = "disabled";
 		};
 
+		pcie@3400000 {
+			compatible = "fsl,ls1028a-pcie";
+			reg = <0x00 0x03400000 0x0 0x00100000   /* controller registers */
+			       0x80 0x00000000 0x0 0x00002000>; /* configuration space */
+			reg-names = "regs", "config";
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; /* aer interrupt */
+			interrupt-names = "pme", "aer";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			dma-coherent;
+			num-viewport = <8>;
+			bus-range = <0x0 0xff>;
+			ranges = <0x81000000 0x0 0x00000000 0x80 0x00010000 0x0 0x00010000   /* downstream I/O */
+				  0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+			msi-parent = <&its>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 2 &gic 0 0 GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 3 &gic 0 0 GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 4 &gic 0 0 GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
+			status = "disabled";
+		};
+
+		pcie@3500000 {
+			compatible = "fsl,ls1028a-pcie";
+			reg = <0x00 0x03500000 0x0 0x00100000   /* controller registers */
+			       0x88 0x00000000 0x0 0x00002000>; /* configuration space */
+			reg-names = "regs", "config";
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pme", "aer";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			dma-coherent;
+			num-viewport = <8>;
+			bus-range = <0x0 0xff>;
+			ranges = <0x81000000 0x0 0x00000000 0x88 0x00010000 0x0 0x00010000   /* downstream I/O */
+				  0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+			msi-parent = <&its>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 2 &gic 0 0 GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 3 &gic 0 0 GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 4 &gic 0 0 GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
+			status = "disabled";
+		};
+
 		smmu: iommu@5000000 {
 			compatible = "arm,mmu-500";
 			reg = <0 0x5000000 0 0x800000>;
@@ -683,7 +776,6 @@ pcie@1f0000000 { /* Integrated Endpoint Root Complex */
 			reg = <0x01 0xf0000000 0x0 0x100000>;
 			#address-cells = <3>;
 			#size-cells = <2>;
-			#interrupt-cells = <1>;
 			msi-parent = <&its>;
 			device_type = "pci";
 			bus-range = <0x0 0x0>;
@@ -701,27 +793,115 @@ pcie@1f0000000 { /* Integrated Endpoint Root Complex */
 				  /* PF1: VF0-1 BAR0 - non-prefetchable memory */
 				  0x82000000 0x0 0x00000000  0x1 0xf8210000  0x0 0x020000
 				  /* PF1: VF0-1 BAR2 - prefetchable memory */
-				  0xc2000000 0x0 0x00000000  0x1 0xf8230000  0x0 0x020000>;
+				  0xc2000000 0x0 0x00000000  0x1 0xf8230000  0x0 0x020000
+				  /* BAR4 (PF5) - non-prefetchable memory */
+				  0x82000000 0x0 0x00000000  0x1 0xfc000000  0x0 0x400000>;
 
 			enetc_port0: ethernet@0,0 {
 				compatible = "fsl,enetc";
 				reg = <0x000000 0 0 0 0>;
+				status = "disabled";
 			};
+
 			enetc_port1: ethernet@0,1 {
 				compatible = "fsl,enetc";
 				reg = <0x000100 0 0 0 0>;
+				status = "disabled";
+			};
+
+			enetc_port2: ethernet@0,2 {
+				compatible = "fsl,enetc";
+				reg = <0x000200 0 0 0 0>;
+				phy-mode = "internal";
+				status = "disabled";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
 			};
+
 			enetc_mdio_pf3: mdio@0,3 {
 				compatible = "fsl,enetc-mdio";
 				reg = <0x000300 0 0 0 0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 			};
+
 			ethernet@0,4 {
 				compatible = "fsl,enetc-ptp";
 				reg = <0x000400 0 0 0 0>;
 				clocks = <&clockgen 4 0>;
 				little-endian;
+				fsl,extts-fifo;
+			};
+
+			mscc_felix: ethernet-switch@0,5 {
+				reg = <0x000500 0 0 0 0>;
+				/* IEP INT_B */
+				interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					/* External ports */
+					mscc_felix_port0: port@0 {
+						reg = <0>;
+						status = "disabled";
+					};
+
+					mscc_felix_port1: port@1 {
+						reg = <1>;
+						status = "disabled";
+					};
+
+					mscc_felix_port2: port@2 {
+						reg = <2>;
+						status = "disabled";
+					};
+
+					mscc_felix_port3: port@3 {
+						reg = <3>;
+						status = "disabled";
+					};
+
+					/* Internal ports */
+					mscc_felix_port4: port@4 {
+						reg = <4>;
+						phy-mode = "internal";
+						status = "disabled";
+
+						fixed-link {
+							speed = <2500>;
+							full-duplex;
+						};
+					};
+
+					mscc_felix_port5: port@5 {
+						reg = <5>;
+						phy-mode = "internal";
+						status = "disabled";
+
+						fixed-link {
+							speed = <1000>;
+							full-duplex;
+						};
+					};
+				};
+			};
+
+			enetc_port3: ethernet@0,6 {
+				compatible = "fsl,enetc";
+				reg = <0x000600 0 0 0 0>;
+				phy-mode = "internal";
+				status = "disabled";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
 			};
 		};
 	};

arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts

@@ -83,6 +83,7 @@ &duart1 {
 };
 
 &esdhc {
+	mmc-hs200-1_8v;
 	status = "okay";
 };
 

arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi

@@ -393,6 +393,7 @@ esdhc: esdhc@2140000 {
 			reg = <0x0 0x2140000 0x0 0x10000>;
 			interrupts = <0 28 0x4>; /* Level high type */
 			clock-frequency = <0>;
+			clocks = <&clockgen 2 1>;
 			voltage-ranges = <1800 1800 3300 3300>;
 			sdhci,auto-cmd12;
 			little-endian;
@@ -493,6 +494,7 @@ pcie@3400000 {
 					<0000 0 0 2 &gic 0 0 0 110 IRQ_TYPE_LEVEL_HIGH>,
 					<0000 0 0 3 &gic 0 0 0 111 IRQ_TYPE_LEVEL_HIGH>,
 					<0000 0 0 4 &gic 0 0 0 112 IRQ_TYPE_LEVEL_HIGH>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
 			status = "disabled";
 		};
 
@@ -518,6 +520,7 @@ pcie@3500000 {
 					<0000 0 0 2 &gic 0 0 0 115 IRQ_TYPE_LEVEL_HIGH>,
 					<0000 0 0 3 &gic 0 0 0 116 IRQ_TYPE_LEVEL_HIGH>,
 					<0000 0 0 4 &gic 0 0 0 117 IRQ_TYPE_LEVEL_HIGH>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
 			status = "disabled";
 		};
 
@@ -543,6 +546,7 @@ pcie@3600000 {
 					<0000 0 0 2 &gic 0 0 0 120 IRQ_TYPE_LEVEL_HIGH>,
 					<0000 0 0 3 &gic 0 0 0 121 IRQ_TYPE_LEVEL_HIGH>,
 					<0000 0 0 4 &gic 0 0 0 122 IRQ_TYPE_LEVEL_HIGH>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
 			status = "disabled";
 		};
 

arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi

@@ -648,6 +648,7 @@ pcie1: pcie@3400000 {
 					<0000 0 0 2 &gic 0 0 0 110 4>,
 					<0000 0 0 3 &gic 0 0 0 111 4>,
 					<0000 0 0 4 &gic 0 0 0 112 4>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
 			status = "disabled";
 		};
 
@@ -669,6 +670,7 @@ pcie2: pcie@3500000 {
 					<0000 0 0 2 &gic 0 0 0 115 4>,
 					<0000 0 0 3 &gic 0 0 0 116 4>,
 					<0000 0 0 4 &gic 0 0 0 117 4>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
 			status = "disabled";
 		};
 
@@ -690,6 +692,7 @@ pcie3: pcie@3600000 {
 					<0000 0 0 2 &gic 0 0 0 120 4>,
 					<0000 0 0 3 &gic 0 0 0 121 4>,
 					<0000 0 0 4 &gic 0 0 0 122 4>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
 			status = "disabled";
 		};
 
@@ -711,6 +714,7 @@ pcie4: pcie@3700000 {
 					<0000 0 0 2 &gic 0 0 0 125 4>,
 					<0000 0 0 3 &gic 0 0 0 126 4>,
 					<0000 0 0 4 &gic 0 0 0 127 4>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
 			status = "disabled";
 		};
 

arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi

@@ -59,6 +59,32 @@ i2c-switch@77 {
 		#size-cells = <0>;
 		reg = <0x77>;
 
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c512";
+				reg = <0x50>;
+			};
+
+			eeprom@51 {
+				compatible = "atmel,spd";
+				reg = <0x51>;
+			};
+
+			eeprom@53 {
+				compatible = "atmel,spd";
+				reg = <0x53>;
+			};
+
+			eeprom@57 {
+				compatible = "atmel,24c02";
+				reg = <0x57>;
+			};
+		};
+
 		i2c@1 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -73,6 +99,17 @@ fan-temperature-ctrlr@18 {
 			};
 		};
 
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			regulator@5c {
+				compatible = "lltc,ltc3882";
+				reg = <0x5c>;
+			};
+		};
+
 		i2c@3 {
 			#address-cells = <1>;
 			#size-cells = <0>;

arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts

@@ -43,6 +43,21 @@ &esdhc1 {
 	status = "okay";
 };
 
+&fspi {
+	status = "okay";
+
+	mt35xu512aba0: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		m25p,fast-read;
+		spi-max-frequency = <50000000>;
+		reg = <0>;
+		spi-rx-bus-width = <8>;
+		spi-tx-bus-width = <8>;
+	};
+};
+
 &i2c0 {
 	status = "okay";
 

arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts

@@ -84,7 +84,7 @@ &fspi {
 	mt35xu512aba0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "spansion,m25p80";
+		compatible = "jedec,spi-nor";
 		m25p,fast-read;
 		spi-max-frequency = <50000000>;
 		reg = <0>;
@@ -95,7 +95,7 @@ mt35xu512aba0: flash@0 {
 	mt35xu512aba1: flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "spansion,m25p80";
+		compatible = "jedec,spi-nor";
 		m25p,fast-read;
 		spi-max-frequency = <50000000>;
 		reg = <1>;

arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi

@@ -834,6 +834,174 @@ sata3: sata@3230000 {
 			status = "disabled";
 		};
 
+		pcie@3400000 {
+			compatible = "fsl,lx2160a-pcie";
+			reg = <0x00 0x03400000 0x0 0x00100000   /* controller registers */
+			       0x80 0x00000000 0x0 0x00001000>; /* configuration space */
+			reg-names = "csr_axi_slave", "config_axi_slave";
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
+				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
+				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
+			interrupt-names = "aer", "pme", "intr";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			dma-coherent;
+			apio-wins = <8>;
+			ppio-wins = <8>;
+			bus-range = <0x0 0xff>;
+			ranges = <0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+			msi-parent = <&its>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 2 &gic 0 0 GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 3 &gic 0 0 GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 4 &gic 0 0 GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
+			status = "disabled";
+		};
+
+		pcie@3500000 {
+			compatible = "fsl,lx2160a-pcie";
+			reg = <0x00 0x03500000 0x0 0x00100000   /* controller registers */
+			       0x88 0x00000000 0x0 0x00001000>; /* configuration space */
+			reg-names = "csr_axi_slave", "config_axi_slave";
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
+			interrupt-names = "aer", "pme", "intr";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			dma-coherent;
+			apio-wins = <8>;
+			ppio-wins = <8>;
+			bus-range = <0x0 0xff>;
+			ranges = <0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+			msi-parent = <&its>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 2 &gic 0 0 GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 3 &gic 0 0 GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 4 &gic 0 0 GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
+			status = "disabled";
+		};
+
+		pcie@3600000 {
+			compatible = "fsl,lx2160a-pcie";
+			reg = <0x00 0x03600000 0x0 0x00100000   /* controller registers */
+			       0x90 0x00000000 0x0 0x00001000>; /* configuration space */
+			reg-names = "csr_axi_slave", "config_axi_slave";
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
+				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
+				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
+			interrupt-names = "aer", "pme", "intr";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			dma-coherent;
+			apio-wins = <256>;
+			ppio-wins = <24>;
+			bus-range = <0x0 0xff>;
+			ranges = <0x82000000 0x0 0x40000000 0x90 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+			msi-parent = <&its>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 2 &gic 0 0 GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 3 &gic 0 0 GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 4 &gic 0 0 GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
+			status = "disabled";
+		};
+
+		pcie@3700000 {
+			compatible = "fsl,lx2160a-pcie";
+			reg = <0x00 0x03700000 0x0 0x00100000   /* controller registers */
+			       0x98 0x00000000 0x0 0x00001000>; /* configuration space */
+			reg-names = "csr_axi_slave", "config_axi_slave";
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
+				     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
+				     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
+			interrupt-names = "aer", "pme", "intr";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			dma-coherent;
+			apio-wins = <8>;
+			ppio-wins = <8>;
+			bus-range = <0x0 0xff>;
+			ranges = <0x82000000 0x0 0x40000000 0x98 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+			msi-parent = <&its>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 2 &gic 0 0 GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 3 &gic 0 0 GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 4 &gic 0 0 GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
+			status = "disabled";
+		};
+
+		pcie@3800000 {
+			compatible = "fsl,lx2160a-pcie";
+			reg = <0x00 0x03800000 0x0 0x00100000   /* controller registers */
+			       0xa0 0x00000000 0x0 0x00001000>; /* configuration space */
+			reg-names = "csr_axi_slave", "config_axi_slave";
+			interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
+				     <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
+				     <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
+			interrupt-names = "aer", "pme", "intr";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			dma-coherent;
+			apio-wins = <256>;
+			ppio-wins = <24>;
+			bus-range = <0x0 0xff>;
+			ranges = <0x82000000 0x0 0x40000000 0xa0 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+			msi-parent = <&its>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 2 &gic 0 0 GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 3 &gic 0 0 GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 4 &gic 0 0 GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
+			status = "disabled";
+		};
+
+		pcie@3900000 {
+			compatible = "fsl,lx2160a-pcie";
+			reg = <0x00 0x03900000 0x0 0x00100000   /* controller registers */
+			       0xa8 0x00000000 0x0 0x00001000>; /* configuration space */
+			reg-names = "csr_axi_slave", "config_axi_slave";
+			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
+			interrupt-names = "aer", "pme", "intr";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			dma-coherent;
+			apio-wins = <8>;
+			ppio-wins = <8>;
+			bus-range = <0x0 0xff>;
+			ranges = <0x82000000 0x0 0x40000000 0xa8 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+			msi-parent = <&its>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 2 &gic 0 0 GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 3 &gic 0 0 GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 4 &gic 0 0 GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
+			status = "disabled";
+		};
+
 		smmu: iommu@5000000 {
 			compatible = "arm,mmu-500";
 			reg = <0 0x5000000 0 0x800000>;

arch/arm64/boot/dts/freescale/imx8mm-evk.dts

@@ -107,6 +107,8 @@ &fec1 {
 	pinctrl-0 = <&pinctrl_fec1>;
 	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy0>;
+	phy-reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <10>;
 	fsl,magic-packet;
 	status = "okay";
 

arch/arm64/boot/dts/freescale/imx8mm.dtsi

@@ -68,6 +68,7 @@ A53_0: cpu@0 {
 			nvmem-cells = <&cpu_speed_grade>;
 			nvmem-cell-names = "speed_grade";
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_1: cpu@1 {
@@ -80,6 +81,7 @@ A53_1: cpu@1 {
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_2: cpu@2 {
@@ -92,6 +94,7 @@ A53_2: cpu@2 {
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_3: cpu@3 {
@@ -104,6 +107,7 @@ A53_3: cpu@3 {
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_L2: l2-cache0 {
@@ -204,6 +208,38 @@ timer {
 		arm,no-tick-in-suspend;
 	};
 
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <2000>;
+			thermal-sensors = <&tmu>;
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit0: trip1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device =
+						<&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
 	usbphynop1: usbphynop1 {
 		compatible = "usb-nop-xceiv";
 		clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
@@ -227,7 +263,8 @@ soc@0 {
 		ranges = <0x0 0x0 0x0 0x3e000000>;
 
 		aips1: bus@30000000 {
-			compatible = "simple-bus";
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x301f0000 0x10000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x30000000 0x30000000 0x400000>;
@@ -363,6 +400,13 @@ gpio5: gpio@30240000 {
 				gpio-ranges = <&iomuxc 0 119 30>;
 			};
 
+			tmu: tmu@30260000 {
+				compatible = "fsl,imx8mm-tmu";
+				reg = <0x30260000 0x10000>;
+				clocks = <&clk IMX8MM_CLK_TMU_ROOT>;
+				#thermal-sensor-cells = <0>;
+			};
+
 			wdog1: watchdog@30280000 {
 				compatible = "fsl,imx8mm-wdt", "fsl,imx21-wdt";
 				reg = <0x30280000 0x10000>;
@@ -455,6 +499,8 @@ snvs_pwrkey: snvs-powerkey {
 					compatible = "fsl,sec-v4.0-pwrkey";
 					regmap = <&snvs>;
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clk IMX8MM_CLK_SNVS_ROOT>;
+					clock-names = "snvs-pwrkey";
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
 					status = "disabled";
@@ -496,7 +542,8 @@ src: reset-controller@30390000 {
 		};
 
 		aips2: bus@30400000 {
-			compatible = "simple-bus";
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x305f0000 0x10000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x30400000 0x30400000 0x400000>;
@@ -555,10 +602,12 @@ system_counter: timer@306a0000 {
 		};
 
 		aips3: bus@30800000 {
-			compatible = "simple-bus";
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x309f0000 0x10000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges = <0x30800000 0x30800000 0x400000>;
+			ranges = <0x30800000 0x30800000 0x400000>,
+				 <0x8000000 0x8000000 0x10000000>;
 
 			ecspi1: spi@30820000 {
 				compatible = "fsl,imx8mm-ecspi", "fsl,imx51-ecspi";
@@ -760,6 +809,19 @@ usdhc3: mmc@30b60000 {
 				status = "disabled";
 			};
 
+			flexspi: spi@30bb0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "nxp,imx8mm-fspi";
+				reg = <0x30bb0000 0x10000>, <0x8000000 0x10000000>;
+				reg-names = "fspi_base", "fspi_mmap";
+				interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_QSPI_ROOT>,
+					 <&clk IMX8MM_CLK_QSPI_ROOT>;
+				clock-names = "fspi", "fspi_en";
+				status = "disabled";
+			};
+
 			sdma1: dma-controller@30bd0000 {
 				compatible = "fsl,imx8mm-sdma", "fsl,imx8mq-sdma";
 				reg = <0x30bd0000 0x10000>;
@@ -800,7 +862,8 @@ fec1: ethernet@30be0000 {
 		};
 
 		aips4: bus@32c00000 {
-			compatible = "simple-bus";
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x32df0000 0x10000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x32c00000 0x32c00000 0x400000>;
@@ -896,7 +959,6 @@ ddrc: memory-controller@3d400000 {
 		ddr-pmu@3d800000 {
 			compatible = "fsl,imx8mm-ddr-pmu", "fsl,imx8m-ddr-pmu";
 			reg = <0x3d800000 0x400000>;
-			interrupt-parent = <&gic>;
 			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
 		};
 	};

arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi

@@ -102,6 +102,20 @@ typec1_con: connector {
 	};
 };
 
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	pca6416: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
 &snvs_pwrkey {
 	status = "okay";
 };
@@ -202,6 +216,13 @@ MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA		0x400001c3
 		>;
 	};
 
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_I2C3_SCL_I2C3_SCL		0x400001c3
+			MX8MN_IOMUXC_I2C3_SDA_I2C3_SDA		0x400001c3
+		>;
+	};
+
 	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
 		fsl,pins = <
 			MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41

arch/arm64/boot/dts/freescale/imx8mn.dtsi

@@ -7,6 +7,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
 
 #include "imx8mn-pinfunc.h"
 
@@ -67,6 +68,7 @@ A53_0: cpu@0 {
 			nvmem-cells = <&cpu_speed_grade>;
 			nvmem-cell-names = "speed_grade";
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_1: cpu@1 {
@@ -79,6 +81,7 @@ A53_1: cpu@1 {
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_2: cpu@2 {
@@ -91,6 +94,7 @@ A53_2: cpu@2 {
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_3: cpu@3 {
@@ -103,6 +107,7 @@ A53_3: cpu@3 {
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_L2: l2-cache0 {
@@ -116,7 +121,7 @@ a53_opp_table: opp-table {
 
 		opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
-			opp-microvolt = <850000>;
+			opp-microvolt = <950000>;
 			opp-supported-hw = <0xb00>, <0x7>;
 			clock-latency-ns = <150000>;
 			opp-suspend;
@@ -186,6 +191,38 @@ psci {
 		method = "smc";
 	};
 
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <2000>;
+			thermal-sensors = <&tmu>;
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit0: trip1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device =
+						<&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
@@ -203,8 +240,8 @@ soc@0 {
 		ranges = <0x0 0x0 0x0 0x3e000000>;
 
 		aips1: bus@30000000 {
-			compatible = "simple-bus";
-			reg = <0x30000000 0x400000>;
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x301f0000 0x10000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -274,6 +311,13 @@ gpio5: gpio@30240000 {
 				gpio-ranges = <&iomuxc 0 119 30>;
 			};
 
+			tmu: tmu@30260000 {
+				compatible = "fsl,imx8mn-tmu", "fsl,imx8mm-tmu";
+				reg = <0x30260000 0x10000>;
+				clocks = <&clk IMX8MN_CLK_TMU_ROOT>;
+				#thermal-sensor-cells = <0>;
+			};
+
 			wdog1: watchdog@30280000 {
 				compatible = "fsl,imx8mn-wdt", "fsl,imx21-wdt";
 				reg = <0x30280000 0x10000>;
@@ -358,6 +402,7 @@ snvs_rtc: snvs-rtc-lp {
 					offset = <0x34>;
 					interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
 						     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clk IMX8MN_CLK_SNVS_ROOT>;
 					clock-names = "snvs-rtc";
 				};
 
@@ -365,6 +410,8 @@ snvs_pwrkey: snvs-powerkey {
 					compatible = "fsl,sec-v4.0-pwrkey";
 					regmap = <&snvs>;
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clk IMX8MN_CLK_SNVS_ROOT>;
+					clock-names = "snvs-pwrkey";
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
 					status = "disabled";
@@ -379,6 +426,16 @@ clk: clock-controller@30380000 {
 					 <&clk_ext3>, <&clk_ext4>;
 				clock-names = "osc_32k", "osc_24m", "clk_ext1", "clk_ext2",
 					      "clk_ext3", "clk_ext4";
+				assigned-clocks = <&clk IMX8MN_CLK_NOC>,
+						<&clk IMX8MN_CLK_AUDIO_AHB>,
+						<&clk IMX8MN_CLK_IPG_AUDIO_ROOT>,
+						<&clk IMX8MN_SYS_PLL3>;
+				assigned-clock-parents = <&clk IMX8MN_SYS_PLL3_OUT>,
+							 <&clk IMX8MN_SYS_PLL1_800M>;
+				assigned-clock-rates = <0>,
+							<400000000>,
+							<400000000>,
+							<600000000>;
 			};
 
 			src: reset-controller@30390000 {
@@ -390,8 +447,8 @@ src: reset-controller@30390000 {
 		};
 
 		aips2: bus@30400000 {
-			compatible = "simple-bus";
-			reg = <0x30400000 0x400000>;
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x305f0000 0x10000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -450,8 +507,8 @@ system_counter: timer@306a0000 {
 		};
 
 		aips3: bus@30800000 {
-			compatible = "simple-bus";
-			reg = <0x30800000 0x400000>;
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x309f0000 0x10000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -543,19 +600,19 @@ crypto: crypto@30900000 {
 					 <&clk IMX8MN_CLK_IPG_ROOT>;
 				clock-names = "aclk", "ipg";
 
-				sec_jr0: jr0@1000 {
+				sec_jr0: jr@1000 {
 					 compatible = "fsl,sec-v4.0-job-ring";
 					 reg = <0x1000 0x1000>;
 					 interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 				};
 
-				sec_jr1: jr1@2000 {
+				sec_jr1: jr@2000 {
 					 compatible = "fsl,sec-v4.0-job-ring";
 					 reg = <0x2000 0x1000>;
 					 interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
 				};
 
-				sec_jr2: jr2@3000 {
+				sec_jr2: jr@3000 {
 					 compatible = "fsl,sec-v4.0-job-ring";
 					 reg = <0x3000 0x1000>;
 					 interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
@@ -696,8 +753,8 @@ fec1: ethernet@30be0000 {
 		};
 
 		aips4: bus@32c00000 {
-			compatible = "simple-bus";
-			reg = <0x32c00000 0x400000>;
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x32df0000 0x10000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;

arch/arm64/boot/dts/freescale/imx8mp-evk.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 NXP
+ */
+
+/dts-v1/;
+
+#include "imx8mp.dtsi"
+
+/ {
+	model = "NXP i.MX8MPlus EVK board";
+	compatible = "fsl,imx8mp-evk", "fsl,imx8mp";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_led>;
+
+		status {
+			label = "yellow:status";
+			gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0xc0000000>,
+		      <0x1 0x00000000 0 0xc0000000>;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy1>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			eee-broken-1000t;
+			reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	pca6416: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&uart2 {
+	/* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usdhc2 {
+	assigned-clocks = <&clk IMX8MP_CLK_USDHC2>;
+	assigned-clock-rates = <400000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usdhc3 {
+	assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
+	assigned-clock-rates = <400000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x3
+			MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x3
+			MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0		0x91
+			MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1		0x91
+			MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2		0x91
+			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3		0x91
+			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x91
+			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x91
+			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0		0x1f
+			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1		0x1f
+			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2		0x1f
+			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3		0x1f
+			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x1f
+			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC		0x1f
+			MX8MP_IOMUXC_SAI1_RXD0__GPIO4_IO02		0x19
+		>;
+	};
+
+	pinctrl_gpio_led: gpioledgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16	0x19
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL		0x400001c3
+			MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x41
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x49
+			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX	0x49
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK	0x190
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD	0x1d0
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d0
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d0
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d0
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d0
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp-100mhz {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK	0x194
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD	0x1d4
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d4
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d4
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d4
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d4
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp-200mhz {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK	0x196
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD	0x1d6
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d6
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d6
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d6
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d6
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2grp-gpio {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12	0x1c4
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x190
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d0
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d0
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d0
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d0
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d0
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d0
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d0
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d0
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d0
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x190
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x194
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d4
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d4
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d4
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d4
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d4
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d4
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d4
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d4
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d4
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x196
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d6
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d6
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d6
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d6
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d6
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d6
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d6
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d6
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d6
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B	0xc6
+		>;
+	};
+};

arch/arm64/boot/dts/freescale/imx8mq-evk.dts

@@ -137,6 +137,8 @@ &fec1 {
 	pinctrl-0 = <&pinctrl_fec1>;
 	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy0>;
+	phy-reset-gpios = <&gpio1 9  GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <10>;
 	fsl,magic-packet;
 	status = "okay";
 

arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts

@@ -55,6 +55,15 @@ hp-det {
 			wakeup-source;
 			linux,code = <KEY_HP>;
 		};
+
+		wwan-wake {
+			label = "WWAN_WAKE";
+			gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
+			interrupt-parent = <&gpio3>;
+			interrupts = <8 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+			linux,code = <KEY_PHONE>;
+		};
 	};
 
 	leds {
@@ -148,6 +157,55 @@ reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
 		regulator-always-on;
 	};
 
+	wwan_codec: sound-wwan-codec {
+		compatible = "option,gtm601";
+		#sound-dai-cells = <0>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "sgtl5000";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "Speaker Ext",
+			"Line", "Line In Jack";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"Microphone Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"Speaker Ext", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&sgtl5000>;
+			clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>;
+			frame-master;
+			bitclock-master;
+		};
+	};
+
+	sound-wwan {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "SIMCom SIM7100";
+		simple-audio-card,format = "dsp_a";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai6>;
+		};
+
+		telephony_link_master: simple-audio-card,codec {
+			sound-dai = <&wwan_codec>;
+			frame-master;
+			bitclock-master;
+		};
+	};
+
 	vibrator {
 		compatible = "gpio-vibrator";
 		pinctrl-names = "default";
@@ -169,6 +227,22 @@ wifi_pwr_en: regulator-wifi-en {
 	};
 };
 
+&A53_0 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck2_reg>;
+};
+
 &clk {
 	assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL2>;
 	assigned-clock-rates = <786432000>, <722534400>;
@@ -354,10 +428,10 @@ connector {
 				PDO_FIXED_USB_COMM |
 				PDO_FIXED_DUAL_ROLE |
 				PDO_FIXED_DATA_SWAP )>;
-			sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM |
+			sink-pdos = <PDO_FIXED(5000, 3500, PDO_FIXED_USB_COMM |
 				PDO_FIXED_DUAL_ROLE |
 				PDO_FIXED_DATA_SWAP )
-			     PDO_VAR(5000, 3000, 3000)>;
+			     PDO_VAR(5000, 5000, 3500)>;
 			op-sink-microwatt = <10000000>;
 
 			ports {
@@ -426,6 +500,19 @@ magnetometer@1e	{
 		vddio-supply = <&reg_3v3_p>;
 	};
 
+	sgtl5000: audio-codec@a {
+		compatible = "fsl,sgtl5000";
+		clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>;
+		assigned-clocks = <&clk IMX8MQ_CLK_SAI2>;
+		assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>;
+		assigned-clock-rates = <24576000>;
+		#sound-dai-cells = <0>;
+		reg = <0x0a>;
+		VDDD-supply = <&reg_1v8_p>;
+		VDDIO-supply = <&reg_3v3_p>;
+		VDDA-supply = <&reg_3v3_p>;
+	};
+
 	touchscreen@5d {
 		compatible = "goodix,gt5688";
 		reg = <0x5d>;
@@ -441,11 +528,20 @@ touchscreen@5d {
 		VDDIO-supply = <&reg_1v8_p>;
 	};
 
+	proximity-sensor@60 {
+		compatible = "vishay,vcnl4040";
+		reg = <0x60>;
+		pinctrl-0 = <&pinctrl_prox>;
+	};
+
 	accel-gyro@6a {
 		compatible = "st,lsm9ds1-imu";
 		reg = <0x6a>;
 		vdd-supply = <&reg_3v3_p>;
 		vddio-supply = <&reg_3v3_p>;
+		mount-matrix =  "1",  "0",  "0",
+				"0",  "1",  "0",
+				"0",  "0", "-1";
 	};
 };
 
@@ -508,6 +604,7 @@ pinctrl_gpio_keys: gpiokeygrp {
 			MX8MQ_IOMUXC_SAI2_RXFS_GPIO4_IO21	0x16
 			MX8MQ_IOMUXC_SAI2_RXC_GPIO4_IO22	0x16
 			MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20	0x180  /* HP_DET */
+			MX8MQ_IOMUXC_NAND_DATA02_GPIO3_IO8	0x80   /* nWoWWAN */
 		>;
 	};
 
@@ -543,6 +640,12 @@ MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x80  /* PMIC intr */
 		>;
 	};
 
+	pinctrl_prox: proxgrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x80  /* prox intr */
+		>;
+	};
+
 	pinctrl_pwr_en: pwrengrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8	0x06
@@ -555,6 +658,25 @@ MX8MQ_IOMUXC_SAI3_RXC_GPIO4_IO29	0x80  /* RTC intr */
 		>;
 	};
 
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC	0xd6
+			MX8MQ_IOMUXC_SAI2_TXC_SAI2_TX_BCLK	0xd6
+			MX8MQ_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0	0xd6
+			MX8MQ_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0	0xd6
+			MX8MQ_IOMUXC_SAI2_MCLK_SAI2_MCLK	0xd6
+		>;
+	};
+
+	pinctrl_sai6: sai6grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SAI1_RXD5_SAI6_RX_DATA0	0xd6
+			MX8MQ_IOMUXC_SAI1_RXD6_SAI6_RX_SYNC	0xd6
+			MX8MQ_IOMUXC_SAI1_TXD4_SAI6_RX_BCLK     0xd6
+			MX8MQ_IOMUXC_SAI1_TXD5_SAI6_TX_DATA0	0xd6
+		>;
+	};
+
 	pinctrl_typec: typecgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12		0x16
@@ -730,6 +852,25 @@ &snvs_pwrkey {
 	status = "okay";
 };
 
+&sai2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	assigned-clocks = <&clk IMX8MQ_CLK_SAI2>;
+	assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	status = "okay";
+};
+
+&sai6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai6>;
+	assigned-clocks = <&clk IMX8MQ_CLK_SAI6>;
+	assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	fsl,sai-synchronous-rx;
+	status = "okay";
+};
+
 &uart1 { /* console */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
@@ -750,6 +891,7 @@ &uart4 { /* BT */
 };
 
 &usb3_phy0 {
+	vbus-supply = <&reg_5v_p>;
 	status = "okay";
 };
 
@@ -808,7 +950,7 @@ &usdhc2 {
 	bus-width = <4>;
 	vmmc-supply = <&reg_usdhc2_vmmc>;
 	power-supply = <&wifi_pwr_en>;
-	non-removable;
+	broken-cd;
 	disable-wp;
 	cap-sdio-irq;
 	keep-power-in-suspend;

arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts

@@ -35,6 +35,16 @@ reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
 		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
+
+	fan: gpio-fan {
+		compatible = "gpio-fan";
+		gpio-fan,speed-map = <0 0 8600 1>;
+		gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		#cooling-cells = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_fan>;
+		status = "okay";
+	};
 };
 
 &A53_0 {
@@ -53,6 +63,53 @@ &A53_3 {
 	cpu-supply = <&buck2>;
 };
 
+&cpu_thermal {
+	trips {
+		cpu_alert0: trip0 {
+			temperature = <75000>;
+			hysteresis = <2000>;
+			type = "passive";
+		};
+
+		cpu_alert1: trip1 {
+			temperature = <80000>;
+			hysteresis = <2000>;
+			type = "passive";
+		};
+
+		cpu_crit0: trip3 {
+			temperature = <90000>;
+			hysteresis = <2000>;
+			type = "critical";
+		};
+
+		fan_toggle0: trip4 {
+			temperature = <65000>;
+			hysteresis = <10000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map0 {
+			trip = <&cpu_alert0>;
+			cooling-device =
+			<&A53_0 0 1>; /* Exclude highest OPP */
+		};
+
+		map1 {
+			trip = <&cpu_alert1>;
+			cooling-device =
+			<&A53_0 0 2>; /* Exclude two highest OPPs */
+		};
+
+		map4 {
+			trip = <&fan_toggle0>;
+			cooling-device = <&fan 0 1>;
+		};
+	};
+};
+
 &i2c1 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default";
@@ -201,6 +258,27 @@ ldo7: LDO7 {
 	};
 };
 
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <10>;
+	phy-reset-post-delay = <50>;
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+		};
+	};
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
@@ -254,6 +332,32 @@ &wdog1 {
 };
 
 &iomuxc {
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC			0x3
+			MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO		0x23
+			MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
+			MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
+			MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
+			MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
+			MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
+			MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
+			MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
+			MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
+			MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
+			MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
+		>;
+	};
+
+	pinctrl_gpio_fan: gpiofangrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5			0x16
+		>;
+	};
+
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL			0x4000007f

arch/arm64/boot/dts/freescale/imx8mq.dtsi

@@ -198,7 +198,7 @@ psci {
 	};
 
 	thermal-zones {
-		cpu-thermal {
+		cpu_thermal: cpu-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <2000>;
 			thermal-sensors = <&tmu 0>;
@@ -290,7 +290,8 @@ soc@0 {
 		dma-ranges = <0x40000000 0x0 0x40000000 0xc0000000>;
 
 		bus@30000000 { /* AIPS1 */
-			compatible = "simple-bus";
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x301f0000 0x10000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x30000000 0x30000000 0x400000>;
@@ -521,7 +522,7 @@ lcdif: lcd-controller@30320000 {
 				status = "disabled";
 			};
 
-			iomuxc: iomuxc@30330000 {
+			iomuxc: pinctrl@30330000 {
 				compatible = "fsl,imx8mq-iomuxc";
 				reg = <0x30330000 0x10000>;
 			};
@@ -574,6 +575,8 @@ snvs_pwrkey: snvs-powerkey {
 					compatible = "fsl,sec-v4.0-pwrkey";
 					regmap = <&snvs>;
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clk IMX8MQ_CLK_SNVS_ROOT>;
+					clock-names = "snvs-pwrkey";
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
 					status = "disabled";
@@ -692,7 +695,8 @@ pgc_pcie2: power-domain@a {
 		};
 
 		bus@30400000 { /* AIPS2 */
-			compatible = "simple-bus";
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x305f0000 0x10000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x30400000 0x30400000 0x400000>;
@@ -751,7 +755,8 @@ system_counter: timer@306a0000 {
 		};
 
 		bus@30800000 { /* AIPS3 */
-			compatible = "simple-bus";
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x309f0000 0x10000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x30800000 0x30800000 0x400000>,
@@ -1023,7 +1028,8 @@ fec1: ethernet@30be0000 {
 		};
 
 		bus@32c00000 { /* AIPS4 */
-			compatible = "simple-bus";
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x32df0000 0x10000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x32c00000 0x32c00000 0x400000>;

arch/arm64/boot/dts/freescale/imx8qxp.dtsi

@@ -11,6 +11,7 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/pinctrl/pads-imx8qxp.h>
+#include <dt-bindings/thermal/thermal.h>
 
 / {
 	interrupt-parent = <&gic>;
@@ -189,6 +190,11 @@ watchdog {
 			compatible = "fsl,imx8qxp-sc-wdt", "fsl,imx-sc-wdt";
 			timeout-sec = <60>;
 		};
+
+		tsens: thermal-sensor {
+			compatible = "fsl,imx8qxp-sc-thermal", "fsl,imx-sc-thermal";
+			#thermal-sensor-cells = <1>;
+		};
 	};
 
 	timer {
@@ -586,4 +592,37 @@ lsio_lpcg: clock-controller@5d400000 {
 			#clock-cells = <1>;
 		};
 	};
+
+	thermal_zones: thermal-zones {
+		cpu-thermal0 {
+			polling-delay-passive = <250>;
+			polling-delay = <2000>;
+			thermal-sensors = <&tsens IMX_SC_R_SYSTEM>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <107000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit0: trip1 {
+					temperature = <127000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device =
+						<&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A35_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A35_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
 };

arch/arm64/boot/dts/freescale/s32v234.dtsi

@@ -104,7 +104,7 @@ soc {
 		interrupt-parent = <&gic>;
 		ranges;
 
-		aips0: aips-bus@40000000 {
+		aips0: bus@40000000 {
 			compatible = "simple-bus";
 			#address-cells = <2>;
 			#size-cells = <2>;
@@ -120,7 +120,7 @@ uart0: serial@40053000 {
 			};
 		};
 
-		aips1: aips-bus@40080000 {
+		aips1: bus@40080000 {
 			compatible = "simple-bus";
 			#address-cells = <2>;
 			#size-cells = <2>;

drivers/clk/imx/clk-imx8mn.c

@@ -523,6 +523,7 @@ static int imx8mn_clocks_probe(struct platform_device *pdev)
 	hws[IMX8MN_CLK_SAI5_IPG] = imx_clk_hw_gate2_shared2("sai5_ipg_clk", "ipg_audio_root", base + 0x4370, 0, &share_count_sai5);
 	hws[IMX8MN_CLK_SAI6_ROOT] = imx_clk_hw_gate2_shared2("sai6_root_clk", "sai6", base + 0x4380, 0, &share_count_sai6);
 	hws[IMX8MN_CLK_SAI6_IPG] = imx_clk_hw_gate2_shared2("sai6_ipg_clk", "ipg_audio_root", base + 0x4380, 0, &share_count_sai6);
+	hws[IMX8MN_CLK_SNVS_ROOT] = imx_clk_hw_gate4("snvs_root_clk", "ipg_root", base + 0x4470, 0);
 	hws[IMX8MN_CLK_UART1_ROOT] = imx_clk_hw_gate4("uart1_root_clk", "uart1", base + 0x4490, 0);
 	hws[IMX8MN_CLK_UART2_ROOT] = imx_clk_hw_gate4("uart2_root_clk", "uart2", base + 0x44a0, 0);
 	hws[IMX8MN_CLK_UART3_ROOT] = imx_clk_hw_gate4("uart3_root_clk", "uart3", base + 0x44b0, 0);

include/dt-bindings/clock/imx8mn-clock.h

@@ -228,6 +228,8 @@
 #define IMX8MN_SYS_PLL2_333M_CG			209
 #define IMX8MN_SYS_PLL2_500M_CG			210
 
-#define IMX8MN_CLK_END				211
+#define IMX8MN_CLK_SNVS_ROOT			211
+
+#define IMX8MN_CLK_END				212
 
 #endif