serial: remove blackfin drivers

The blackfin architecture is getting removed, so both the bfin_uart
and bfin_sport_uart can be removed as well.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

drivers/tty/serial/Kconfig

@@ -498,92 +498,6 @@ config SERIAL_SA1100_CONSOLE
 	  your boot loader (lilo or loadlin) about how to pass options to the
 	  kernel at boot time.)
 
-config SERIAL_BFIN
-	tristate "Blackfin serial port support"
-	depends on BLACKFIN
-	select SERIAL_CORE
-	select SERIAL_BFIN_UART0 if (BF531 || BF532 || BF533 || BF561)
-	help
-	  Add support for the built-in UARTs on the Blackfin.
-
-	  To compile this driver as a module, choose M here: the
-	  module is named bfin_uart.ko.
-
-config SERIAL_BFIN_CONSOLE
-	bool "Console on Blackfin serial port"
-	depends on SERIAL_BFIN=y
-	select SERIAL_CORE_CONSOLE
-
-choice
-	prompt "UART Mode"
-	depends on SERIAL_BFIN
-	default SERIAL_BFIN_DMA
-	help
-	  This driver supports the built-in serial ports of the Blackfin family
-	  of CPUs
-
-config SERIAL_BFIN_DMA
-	bool "DMA mode"
-	depends on !DMA_UNCACHED_NONE && KGDB_SERIAL_CONSOLE=n
-	help
-	  This driver works under DMA mode. If this option is selected, the
-	  blackfin simple dma driver is also enabled.
-
-config SERIAL_BFIN_PIO
-	bool "PIO mode"
-	help
-	  This driver works under PIO mode.
-
-endchoice
-
-config SERIAL_BFIN_UART0
-	bool "Enable UART0"
-	depends on SERIAL_BFIN
-	help
-	  Enable UART0
-
-config BFIN_UART0_CTSRTS
-	bool "Enable UART0 hardware flow control"
-	depends on SERIAL_BFIN_UART0
-	help
-	  Enable hardware flow control in the driver.
-
-config SERIAL_BFIN_UART1
-	bool "Enable UART1"
-	depends on SERIAL_BFIN && (!BF531 && !BF532 && !BF533 && !BF561)
-	help
-	  Enable UART1
-
-config BFIN_UART1_CTSRTS
-	bool "Enable UART1 hardware flow control"
-	depends on SERIAL_BFIN_UART1
-	help
-	  Enable hardware flow control in the driver.
-
-config SERIAL_BFIN_UART2
-	bool "Enable UART2"
-	depends on SERIAL_BFIN && (BF54x || BF538 || BF539)
-	help
-	  Enable UART2
-
-config BFIN_UART2_CTSRTS
-	bool "Enable UART2 hardware flow control"
-	depends on SERIAL_BFIN_UART2
-	help
-	  Enable hardware flow control in the driver.
-
-config SERIAL_BFIN_UART3
-	bool "Enable UART3"
-	depends on SERIAL_BFIN && (BF54x)
-	help
-	  Enable UART3
-
-config BFIN_UART3_CTSRTS
-	bool "Enable UART3 hardware flow control"
-	depends on SERIAL_BFIN_UART3
-	help
-	  Enable hardware flow control in the driver.
-
 config SERIAL_IMX
 	tristate "IMX serial port support"
 	depends on HAS_DMA
@@ -1231,69 +1145,6 @@ config SERIAL_SC16IS7XX_SPI
           This is additional support to exsisting driver.
           You must select at least one bus for the driver to be built.
 
-config SERIAL_BFIN_SPORT
-	tristate "Blackfin SPORT emulate UART"
-	depends on BLACKFIN
-	select SERIAL_CORE
-	help
-	  Enable SPORT emulate UART on Blackfin series.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called bfin_sport_uart.
-
-config SERIAL_BFIN_SPORT_CONSOLE
-	bool "Console on Blackfin sport emulated uart"
-	depends on SERIAL_BFIN_SPORT=y
-	select SERIAL_CORE_CONSOLE
-
-config SERIAL_BFIN_SPORT0_UART
-	bool "Enable UART over SPORT0"
-	depends on SERIAL_BFIN_SPORT && !(BF542 || BF544)
-	help
-	  Enable UART over SPORT0
-
-config SERIAL_BFIN_SPORT0_UART_CTSRTS
-	bool "Enable UART over SPORT0 hardware flow control"
-	depends on SERIAL_BFIN_SPORT0_UART
-	help
-	  Enable hardware flow control in the driver.
-
-config SERIAL_BFIN_SPORT1_UART
-	bool "Enable UART over SPORT1"
-	depends on SERIAL_BFIN_SPORT
-	help
-	  Enable UART over SPORT1
-
-config SERIAL_BFIN_SPORT1_UART_CTSRTS
-	bool "Enable UART over SPORT1 hardware flow control"
-	depends on SERIAL_BFIN_SPORT1_UART
-	help
-	  Enable hardware flow control in the driver.
-
-config SERIAL_BFIN_SPORT2_UART
-	bool "Enable UART over SPORT2"
-	depends on SERIAL_BFIN_SPORT && (BF54x || BF538 || BF539)
-	help
-	  Enable UART over SPORT2
-
-config SERIAL_BFIN_SPORT2_UART_CTSRTS
-	bool "Enable UART over SPORT2 hardware flow control"
-	depends on SERIAL_BFIN_SPORT2_UART
-	help
-	  Enable hardware flow control in the driver.
-
-config SERIAL_BFIN_SPORT3_UART
-	bool "Enable UART over SPORT3"
-	depends on SERIAL_BFIN_SPORT && (BF54x || BF538 || BF539)
-	help
-	  Enable UART over SPORT3
-
-config SERIAL_BFIN_SPORT3_UART_CTSRTS
-	bool "Enable UART over SPORT3 hardware flow control"
-	depends on SERIAL_BFIN_SPORT3_UART
-	help
-	  Enable hardware flow control in the driver.
-
 config SERIAL_TIMBERDALE
 	tristate "Support for timberdale UART"
 	select SERIAL_CORE

drivers/tty/serial/Makefile

@@ -29,8 +29,6 @@ obj-$(CONFIG_SERIAL_PXA_NON8250) += pxa.o
 obj-$(CONFIG_SERIAL_PNX8XXX) += pnx8xxx_uart.o
 obj-$(CONFIG_SERIAL_SA1100) += sa1100.o
 obj-$(CONFIG_SERIAL_BCM63XX) += bcm63xx_uart.o
-obj-$(CONFIG_SERIAL_BFIN) += bfin_uart.o
-obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o
 obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o
 obj-$(CONFIG_SERIAL_MAX3100) += max3100.o
 obj-$(CONFIG_SERIAL_MAX310X) += max310x.o

drivers/tty/serial/bfin_sport_uart.h

-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Blackfin On-Chip Sport Emulated UART Driver
- *
- * Copyright 2006-2008 Analog Devices Inc.
- *
- * Enter bugs at http://blackfin.uclinux.org/
- */
-
-/*
- * This driver and the hardware supported are in term of EE-191 of ADI.
- * http://www.analog.com/static/imported-files/application_notes/EE191.pdf 
- * This application note describe how to implement a UART on a Sharc DSP,
- * but this driver is implemented on Blackfin Processor.
- * Transmit Frame Sync is not used by this driver to transfer data out.
- */
-
-#ifndef _BFIN_SPORT_UART_H
-#define _BFIN_SPORT_UART_H
-
-#define OFFSET_TCR1		0x00	/* Transmit Configuration 1 Register */
-#define OFFSET_TCR2		0x04	/* Transmit Configuration 2 Register */
-#define OFFSET_TCLKDIV		0x08	/* Transmit Serial Clock Divider Register */
-#define OFFSET_TFSDIV		0x0C	/* Transmit Frame Sync Divider Register */
-#define OFFSET_TX		0x10	/* Transmit Data Register		*/
-#define OFFSET_RX		0x18	/* Receive Data Register		*/
-#define OFFSET_RCR1		0x20	/* Receive Configuration 1 Register	*/
-#define OFFSET_RCR2		0x24	/* Receive Configuration 2 Register	*/
-#define OFFSET_RCLKDIV		0x28	/* Receive Serial Clock Divider Register */
-#define OFFSET_RFSDIV		0x2c	/* Receive Frame Sync Divider Register */
-#define OFFSET_STAT		0x30	/* Status Register			*/
-
-#define SPORT_GET_TCR1(sport)		bfin_read16(((sport)->port.membase + OFFSET_TCR1))
-#define SPORT_GET_TCR2(sport)		bfin_read16(((sport)->port.membase + OFFSET_TCR2))
-#define SPORT_GET_TCLKDIV(sport)	bfin_read16(((sport)->port.membase + OFFSET_TCLKDIV))
-#define SPORT_GET_TFSDIV(sport)		bfin_read16(((sport)->port.membase + OFFSET_TFSDIV))
-#define SPORT_GET_TX(sport)		bfin_read16(((sport)->port.membase + OFFSET_TX))
-#define SPORT_GET_RX(sport)		bfin_read16(((sport)->port.membase + OFFSET_RX))
-/*
- * If another interrupt fires while doing a 32-bit read from RX FIFO,
- * a fake RX underflow error will be generated.  So disable interrupts
- * to prevent interruption while reading the FIFO.
- */
-#define SPORT_GET_RX32(sport) \
-({ \
-	unsigned int __ret; \
-	unsigned long flags; \
-	if (ANOMALY_05000473) \
-		local_irq_save(flags); \
-	__ret = bfin_read32((sport)->port.membase + OFFSET_RX); \
-	if (ANOMALY_05000473) \
-		local_irq_restore(flags); \
-	__ret; \
-})
-#define SPORT_GET_RCR1(sport)		bfin_read16(((sport)->port.membase + OFFSET_RCR1))
-#define SPORT_GET_RCR2(sport)		bfin_read16(((sport)->port.membase + OFFSET_RCR2))
-#define SPORT_GET_RCLKDIV(sport)	bfin_read16(((sport)->port.membase + OFFSET_RCLKDIV))
-#define SPORT_GET_RFSDIV(sport)		bfin_read16(((sport)->port.membase + OFFSET_RFSDIV))
-#define SPORT_GET_STAT(sport)		bfin_read16(((sport)->port.membase + OFFSET_STAT))
-
-#define SPORT_PUT_TCR1(sport, v)	bfin_write16(((sport)->port.membase + OFFSET_TCR1), v)
-#define SPORT_PUT_TCR2(sport, v)	bfin_write16(((sport)->port.membase + OFFSET_TCR2), v)
-#define SPORT_PUT_TCLKDIV(sport, v)	bfin_write16(((sport)->port.membase + OFFSET_TCLKDIV), v)
-#define SPORT_PUT_TFSDIV(sport, v)	bfin_write16(((sport)->port.membase + OFFSET_TFSDIV), v)
-#define SPORT_PUT_TX(sport, v)		bfin_write16(((sport)->port.membase + OFFSET_TX), v)
-#define SPORT_PUT_RX(sport, v)		bfin_write16(((sport)->port.membase + OFFSET_RX), v)
-#define SPORT_PUT_RCR1(sport, v)	bfin_write16(((sport)->port.membase + OFFSET_RCR1), v)
-#define SPORT_PUT_RCR2(sport, v)	bfin_write16(((sport)->port.membase + OFFSET_RCR2), v)
-#define SPORT_PUT_RCLKDIV(sport, v)	bfin_write16(((sport)->port.membase + OFFSET_RCLKDIV), v)
-#define SPORT_PUT_RFSDIV(sport, v)	bfin_write16(((sport)->port.membase + OFFSET_RFSDIV), v)
-#define SPORT_PUT_STAT(sport, v)	bfin_write16(((sport)->port.membase + OFFSET_STAT), v)
-
-#define SPORT_TX_FIFO_SIZE	8
-
-#define SPORT_UART_GET_CTS(x)		gpio_get_value(x->cts_pin)
-#define SPORT_UART_DISABLE_RTS(x)	gpio_set_value(x->rts_pin, 1)
-#define SPORT_UART_ENABLE_RTS(x)	gpio_set_value(x->rts_pin, 0)
-
-#if defined(CONFIG_SERIAL_BFIN_SPORT0_UART_CTSRTS) \
-	|| defined(CONFIG_SERIAL_BFIN_SPORT1_UART_CTSRTS) \
-	|| defined(CONFIG_SERIAL_BFIN_SPORT2_UART_CTSRTS) \
-	|| defined(CONFIG_SERIAL_BFIN_SPORT3_UART_CTSRTS)
-# define CONFIG_SERIAL_BFIN_SPORT_CTSRTS
-#endif
-
-#endif /* _BFIN_SPORT_UART_H */