mmc: mxs: use mmc_gpio_get_ro for detecting read-only status

This also fixes that the read-only gpio was used without being
requested.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

drivers/mmc/host/mxs-mmc.c

@@ -38,6 +38,7 @@
 #include <linux/mmc/host.h>
 #include <linux/mmc/mmc.h>
 #include <linux/mmc/sdio.h>
+#include <linux/mmc/slot-gpio.h>
 #include <linux/gpio.h>
 #include <linux/regulator/consumer.h>
 #include <linux/module.h>
@@ -69,26 +70,8 @@ struct mxs_mmc_host {
 	unsigned char			bus_width;
 	spinlock_t			lock;
 	int				sdio_irq_en;
-	int				wp_gpio;
-	bool				wp_inverted;
 };
 
-static int mxs_mmc_get_ro(struct mmc_host *mmc)
-{
-	struct mxs_mmc_host *host = mmc_priv(mmc);
-	int ret;
-
-	if (!gpio_is_valid(host->wp_gpio))
-		return -EINVAL;
-
-	ret = gpio_get_value(host->wp_gpio);
-
-	if (host->wp_inverted)
-		ret = !ret;
-
-	return ret;
-}
-
 static int mxs_mmc_get_cd(struct mmc_host *mmc)
 {
 	struct mxs_mmc_host *host = mmc_priv(mmc);
@@ -551,7 +534,7 @@ static void mxs_mmc_enable_sdio_irq(struct mmc_host *mmc, int enable)
 
 static const struct mmc_host_ops mxs_mmc_ops = {
 	.request = mxs_mmc_request,
-	.get_ro = mxs_mmc_get_ro,
+	.get_ro = mmc_gpio_get_ro,
 	.get_cd = mxs_mmc_get_cd,
 	.set_ios = mxs_mmc_set_ios,
 	.enable_sdio_irq = mxs_mmc_enable_sdio_irq,
@@ -585,7 +568,7 @@ static int mxs_mmc_probe(struct platform_device *pdev)
 	struct mxs_mmc_host *host;
 	struct mmc_host *mmc;
 	struct resource *iores;
-	int ret = 0, irq_err;
+	int ret = 0, irq_err, gpio;
 	struct regulator *reg_vmmc;
 	enum of_gpio_flags flags;
 	struct mxs_ssp *ssp;
@@ -659,9 +642,14 @@ static int mxs_mmc_probe(struct platform_device *pdev)
 		mmc->caps |= MMC_CAP_NEEDS_POLL;
 	if (of_property_read_bool(np, "non-removable"))
 		mmc->caps |= MMC_CAP_NONREMOVABLE;
-	host->wp_gpio = of_get_named_gpio_flags(np, "wp-gpios", 0, &flags);
-	if (flags & OF_GPIO_ACTIVE_LOW)
-		host->wp_inverted = 1;
+	gpio = of_get_named_gpio_flags(np, "wp-gpios", 0, &flags);
+	if (gpio_is_valid(gpio)) {
+		ret = mmc_gpio_request_ro(mmc, gpio);
+		if (ret)
+			goto out_clk_disable;
+		if (!(flags & OF_GPIO_ACTIVE_LOW))
+			mmc->caps2 |= MMC_CAP2_RO_ACTIVE_HIGH;
+	}
 
 	if (of_property_read_bool(np, "cd-inverted"))
 		mmc->caps2 |= MMC_CAP2_CD_ACTIVE_HIGH;