Commit ac219bf3 authored by Linus Walleij's avatar Linus Walleij Committed by Pavel Machek

leds: lp55xx: Convert to use GPIO descriptors

The LP55xx driver is already using the of_gpio() functions to
pick a global GPIO number for "enable" from the device tree and
request the line. Simplify it by just using a GPIO descriptor.

Make sure to keep the enable GPIO line optional, change the
naming from "lp5523_enable" to "LP55xx enable" to reflect that
this is used on all LP55xx LED drivers.

Cc: Milo Kim <milo.kim@ti.com>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: default avatarPavel Machek <pavel@ucw.cz>
parent e190f57d
......@@ -17,8 +17,7 @@
#include <linux/module.h>
#include <linux/platform_data/leds-lp55xx.h>
#include <linux/slab.h>
#include <linux/gpio.h>
#include <linux/of_gpio.h>
#include <linux/gpio/consumer.h>
#include "leds-lp55xx-common.h"
......@@ -395,18 +394,11 @@ int lp55xx_init_device(struct lp55xx_chip *chip)
if (!pdata || !cfg)
return -EINVAL;
if (gpio_is_valid(pdata->enable_gpio)) {
ret = devm_gpio_request_one(dev, pdata->enable_gpio,
GPIOF_DIR_OUT, "lp5523_enable");
if (ret < 0) {
dev_err(dev, "could not acquire enable gpio (err=%d)\n",
ret);
goto err;
}
gpio_set_value(pdata->enable_gpio, 0);
if (pdata->enable_gpiod) {
gpiod_set_consumer_name(pdata->enable_gpiod, "LP55xx enable");
gpiod_set_value(pdata->enable_gpiod, 0);
usleep_range(1000, 2000); /* Keep enable down at least 1ms */
gpio_set_value(pdata->enable_gpio, 1);
gpiod_set_value(pdata->enable_gpiod, 1);
usleep_range(1000, 2000); /* 500us abs min. */
}
......@@ -447,8 +439,8 @@ void lp55xx_deinit_device(struct lp55xx_chip *chip)
if (chip->clk)
clk_disable_unprepare(chip->clk);
if (gpio_is_valid(pdata->enable_gpio))
gpio_set_value(pdata->enable_gpio, 0);
if (pdata->enable_gpiod)
gpiod_set_value(pdata->enable_gpiod, 0);
}
EXPORT_SYMBOL_GPL(lp55xx_deinit_device);
......@@ -579,7 +571,10 @@ struct lp55xx_platform_data *lp55xx_of_populate_pdata(struct device *dev,
of_property_read_string(np, "label", &pdata->label);
of_property_read_u8(np, "clock-mode", &pdata->clock_mode);
pdata->enable_gpio = of_get_named_gpio(np, "enable-gpio", 0);
pdata->enable_gpiod = devm_gpiod_get_optional(dev, "enable",
GPIOD_ASIS);
if (IS_ERR(pdata->enable_gpiod))
return ERR_CAST(pdata->enable_gpiod);
/* LP8501 specific */
of_property_read_u8(np, "pwr-sel", (u8 *)&pdata->pwr_sel);
......
......@@ -12,6 +12,8 @@
#ifndef _LEDS_LP55XX_H
#define _LEDS_LP55XX_H
#include <linux/gpio/consumer.h>
/* Clock configuration */
#define LP55XX_CLOCK_AUTO 0
#define LP55XX_CLOCK_INT 1
......@@ -49,7 +51,7 @@ enum lp8501_pwr_sel {
* @clock_mode : Input clock mode. LP55XX_CLOCK_AUTO or _INT or _EXT
* @setup_resources : Platform specific function before enabling the chip
* @release_resources : Platform specific function after disabling the chip
* @enable : EN pin control by platform side
* @enable_gpiod : enable GPIO descriptor
* @patterns : Predefined pattern data for RGB channels
* @num_patterns : Number of patterns
* @update_config : Value of CONFIG register
......@@ -65,7 +67,7 @@ struct lp55xx_platform_data {
u8 clock_mode;
/* optional enable GPIO */
int enable_gpio;
struct gpio_desc *enable_gpiod;
/* Predefined pattern data */
struct lp55xx_predef_pattern *patterns;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment