USB: pxa2xx_udc -- cleanups, mostly removing dma hooks

Cleanups to the pxa2xx_udc code:

  - Primarily removing unused DMA hooks.
  - One "sparse" warning removed
  - Remove some Lubbock-only LED hooks (for debugging)

That DMA code was never really completed.  It worked, mostly, for IN
transfers (to the host) if they were fortuitously aligned, but that
code was never fully tested.  And it was never coded for OUT transfers
(which is where DMA would really help) ... because of chip errata on
essentially every chip other than the pxa255, and because of design
botches (nothing automated data toggle).  So it's effectively been
dead code for several years now ... no point in keeping it around.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/usb/gadget/pxa2xx_udc.h

@@ -54,8 +54,6 @@ struct pxa2xx_ep {
 	const struct usb_endpoint_descriptor	*desc;
 	struct list_head			queue;
 	unsigned long				pio_irqs;
-	unsigned long				dma_irqs;
-	short					dma; 
 
 	unsigned short				fifo_size;
 	u8					bEndpointAddress;
@@ -63,7 +61,7 @@ struct pxa2xx_ep {
 
 	unsigned				stopped : 1;
 	unsigned				dma_fixup : 1;
-							 
+
 	/* UDCCS = UDC Control/Status for this EP
 	 * UBCR = UDC Byte Count Remaining (contents of OUT fifo)
 	 * UDDR = UDC Endpoint Data Register (the fifo)
@@ -72,12 +70,6 @@ struct pxa2xx_ep {
 	volatile u32				*reg_udccs;
 	volatile u32				*reg_ubcr;
 	volatile u32				*reg_uddr;
-#ifdef USE_DMA
-	volatile u32			*reg_drcmr;
-#define	drcmr(n)  .reg_drcmr = & DRCMR ## n ,
-#else
-#define	drcmr(n)  
-#endif
 };
 
 struct pxa2xx_request {
@@ -85,7 +77,7 @@ struct pxa2xx_request {
 	struct list_head			queue;
 };
 
-enum ep0_state { 
+enum ep0_state {
 	EP0_IDLE,
 	EP0_IN_DATA_PHASE,
 	EP0_OUT_DATA_PHASE,
@@ -108,7 +100,6 @@ struct udc_stats {
 
 #ifdef CONFIG_USB_PXA2XX_SMALL
 /* when memory's tight, SMALL config saves code+data.  */
-#undef	USE_DMA
 #define	PXA_UDC_NUM_ENDPOINTS	3
 #endif
 
@@ -144,37 +135,8 @@ struct pxa2xx_udc {
 #ifdef CONFIG_ARCH_LUBBOCK
 #include <asm/arch/lubbock.h>
 /* lubbock can also report usb connect/disconnect irqs */
-
-#ifdef DEBUG
-#define HEX_DISPLAY(n)	if (machine_is_lubbock()) { LUB_HEXLED = (n); }
 #endif
 
-#endif
-
-/*-------------------------------------------------------------------------*/
-
-/* LEDs are only for debug */
-#ifndef HEX_DISPLAY
-#define HEX_DISPLAY(n)		do {} while(0)
-#endif
-
-#ifdef DEBUG
-#include <asm/leds.h>
-
-#define LED_CONNECTED_ON	leds_event(led_green_on)
-#define LED_CONNECTED_OFF	do { \
-					leds_event(led_green_off); \
-					HEX_DISPLAY(0); \
-				} while(0)
-#endif
-
-#ifndef LED_CONNECTED_ON
-#define LED_CONNECTED_ON	do {} while(0)
-#define LED_CONNECTED_OFF	do {} while(0)
-#endif
-
-/*-------------------------------------------------------------------------*/
-
 static struct pxa2xx_udc *the_controller;
 
 /*-------------------------------------------------------------------------*/