Commit af1c2d81 authored by Benjamin Gaignard's avatar Benjamin Gaignard Committed by Rob Herring

dt-bindings: serial: Convert STM32 UART to json-schema

Convert STM32 UART bindings to json-schema.
Signed-off-by: default avatarBenjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: default avatarRob Herring <robh@kernel.org>
parent d50f974c
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/serial/st,stm32-uart.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
maintainers:
- Erwan Le Ray <erwan.leray@st.com>
title: STMicroelectronics STM32 USART bindings
allOf:
- $ref: rs485.yaml
properties:
compatible:
enum:
- st,stm32-uart
- st,stm32f7-uart
- st,stm32h7-uart
reg:
maxItems: 1
interrupts:
maxItems: 1
clocks:
maxItems: 1
resets:
maxItems: 1
label:
description: label associated with this uart
st,hw-flow-ctrl:
description: enable hardware flow control
$ref: /schemas/types.yaml#/definitions/flag
dmas:
minItems: 1
maxItems: 2
dma-names:
items:
enum: [ rx, tx ]
minItems: 1
maxItems: 2
wakeup-source: true
rs485-rts-delay: true
rs485-rts-active-low: true
linux,rs485-enabled-at-boot-time: true
rs485-rx-during-tx: true
required:
- compatible
- reg
- interrupts
- clocks
additionalProperties: false
examples:
- |
#include <dt-bindings/clock/stm32mp1-clks.h>
usart1: serial@40011000 {
compatible = "st,stm32-uart";
reg = <0x40011000 0x400>;
interrupts = <37>;
clocks = <&rcc 0 164>;
dmas = <&dma2 2 4 0x414 0x0>,
<&dma2 7 4 0x414 0x0>;
dma-names = "rx", "tx";
rs485-rts-active-low;
};
...
* STMicroelectronics STM32 USART
Required properties:
- compatible: can be either:
- "st,stm32-uart",
- "st,stm32f7-uart",
- "st,stm32h7-uart".
depending is compatible with stm32(f4), stm32f7 or stm32h7.
- reg: The address and length of the peripheral registers space
- interrupts:
- The interrupt line for the USART instance,
- An optional wake-up interrupt.
- clocks: The input clock of the USART instance
Optional properties:
- resets: Must contain the phandle to the reset controller.
- pinctrl: The reference on the pins configuration
- st,hw-flow-ctrl: bool flag to enable hardware flow control.
- rs485-rts-delay, rs485-rx-during-tx, rs485-rts-active-low,
linux,rs485-enabled-at-boot-time: see rs485.txt.
- dmas: phandle(s) to DMA controller node(s). Refer to stm32-dma.txt
- dma-names: "rx" and/or "tx"
- wakeup-source: bool flag to indicate this device has wakeup capabilities
- interrupt-names, if optional wake-up interrupt is used, should be:
- "event": the name for the interrupt line of the USART instance
- "wakeup" the name for the optional wake-up interrupt
Examples:
usart4: serial@40004c00 {
compatible = "st,stm32-uart";
reg = <0x40004c00 0x400>;
interrupts = <52>;
clocks = <&clk_pclk1>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart4>;
};
usart2: serial@40004400 {
compatible = "st,stm32-uart";
reg = <0x40004400 0x400>;
interrupts = <38>;
clocks = <&clk_pclk1>;
st,hw-flow-ctrl;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart2 &pinctrl_usart2_rtscts>;
};
usart1: serial@40011000 {
compatible = "st,stm32-uart";
reg = <0x40011000 0x400>;
interrupts = <37>;
clocks = <&rcc 0 164>;
dmas = <&dma2 2 4 0x414 0x0>,
<&dma2 7 4 0x414 0x0>;
dma-names = "rx", "tx";
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment