mmc: sdhci: Handle auto-command errors

If the host controller supports auto-commands then enable the auto-command
error interrupt and handle it. In the case of auto-CMD23, the error is
treated the same as manual CMD23 error. In the case of auto-CMD12,
commands-during-transfer are not permitted, so the error handling is
treated the same as a data error.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

drivers/mmc/host/sdhci.c

@@ -933,6 +933,11 @@ static void sdhci_set_transfer_irqs(struct sdhci_host *host)
 	else
 		host->ier = (host->ier & ~dma_irqs) | pio_irqs;
 
+	if (host->flags & (SDHCI_AUTO_CMD23 | SDHCI_AUTO_CMD12))
+		host->ier |= SDHCI_INT_AUTO_CMD_ERR;
+	else
+		host->ier &= ~SDHCI_INT_AUTO_CMD_ERR;
+
 	sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
 	sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
 }
@@ -2757,6 +2762,21 @@ static void sdhci_timeout_data_timer(struct timer_list *t)
 
 static void sdhci_cmd_irq(struct sdhci_host *host, u32 intmask, u32 *intmask_p)
 {
+	/* Handle auto-CMD12 error */
+	if (intmask & SDHCI_INT_AUTO_CMD_ERR && host->data_cmd) {
+		struct mmc_request *mrq = host->data_cmd->mrq;
+		u16 auto_cmd_status = sdhci_readw(host, SDHCI_AUTO_CMD_STATUS);
+		int data_err_bit = (auto_cmd_status & SDHCI_AUTO_CMD_TIMEOUT) ?
+				   SDHCI_INT_DATA_TIMEOUT :
+				   SDHCI_INT_DATA_CRC;
+
+		/* Treat auto-CMD12 error the same as data error */
+		if (!mrq->sbc && (host->flags & SDHCI_AUTO_CMD12)) {
+			*intmask_p |= data_err_bit;
+			return;
+		}
+	}
+
 	if (!host->cmd) {
 		/*
 		 * SDHCI recovers from errors by resetting the cmd and data
@@ -2791,6 +2811,21 @@ static void sdhci_cmd_irq(struct sdhci_host *host, u32 intmask, u32 *intmask_p)
 		return;
 	}
 
+	/* Handle auto-CMD23 error */
+	if (intmask & SDHCI_INT_AUTO_CMD_ERR) {
+		struct mmc_request *mrq = host->cmd->mrq;
+		u16 auto_cmd_status = sdhci_readw(host, SDHCI_AUTO_CMD_STATUS);
+		int err = (auto_cmd_status & SDHCI_AUTO_CMD_TIMEOUT) ?
+			  -ETIMEDOUT :
+			  -EILSEQ;
+
+		if (mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) {
+			mrq->sbc->error = err;
+			sdhci_finish_mrq(host, mrq);
+			return;
+		}
+	}
+
 	if (intmask & SDHCI_INT_RESPONSE)
 		sdhci_finish_command(host);
 }

drivers/mmc/host/sdhci.h

@@ -153,7 +153,8 @@
 #define  SDHCI_INT_ERROR_MASK	0xFFFF8000
 
 #define  SDHCI_INT_CMD_MASK	(SDHCI_INT_RESPONSE | SDHCI_INT_TIMEOUT | \
-		SDHCI_INT_CRC | SDHCI_INT_END_BIT | SDHCI_INT_INDEX)
+		SDHCI_INT_CRC | SDHCI_INT_END_BIT | SDHCI_INT_INDEX | \
+		SDHCI_INT_AUTO_CMD_ERR)
 #define  SDHCI_INT_DATA_MASK	(SDHCI_INT_DATA_END | SDHCI_INT_DMA_END | \
 		SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL | \
 		SDHCI_INT_DATA_TIMEOUT | SDHCI_INT_DATA_CRC | \
@@ -169,6 +170,10 @@
 #define SDHCI_CQE_INT_MASK (SDHCI_CQE_INT_ERR_MASK | SDHCI_INT_CQE)
 
 #define SDHCI_AUTO_CMD_STATUS	0x3C
+#define  SDHCI_AUTO_CMD_TIMEOUT	0x00000002
+#define  SDHCI_AUTO_CMD_CRC	0x00000004
+#define  SDHCI_AUTO_CMD_END_BIT	0x00000008
+#define  SDHCI_AUTO_CMD_INDEX	0x00000010
 
 #define SDHCI_HOST_CONTROL2		0x3E
 #define  SDHCI_CTRL_UHS_MASK		0x0007