Commit b1708b72 authored by Nicolas Ferre's avatar Nicolas Ferre

ARM: dts: at91: sama5d2: add dma properties to UART nodes

The dmas/dma-names properties are added to the UART nodes. Note that additional
properties are needed to enable them at the board level: check bindings for
details.
Signed-off-by: default avatarNicolas Ferre <nicolas.ferre@atmel.com>
parent 34ff2dc7
......@@ -880,6 +880,13 @@ uart0: serial@f801c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x100>;
interrupts = <24 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(35))>,
<&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(36))>;
dma-names = "tx", "rx";
clocks = <&uart0_clk>;
clock-names = "usart";
status = "disabled";
......@@ -889,6 +896,13 @@ uart1: serial@f8020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x100>;
interrupts = <25 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(37))>,
<&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(38))>;
dma-names = "tx", "rx";
clocks = <&uart1_clk>;
clock-names = "usart";
status = "disabled";
......@@ -898,6 +912,13 @@ uart2: serial@f8024000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x100>;
interrupts = <26 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(39))>,
<&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(40))>;
dma-names = "tx", "rx";
clocks = <&uart2_clk>;
clock-names = "usart";
status = "disabled";
......@@ -1016,6 +1037,13 @@ uart3: serial@fc008000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfc008000 0x100>;
interrupts = <27 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(41))>,
<&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(42))>;
dma-names = "tx", "rx";
clocks = <&uart3_clk>;
clock-names = "usart";
status = "disabled";
......@@ -1024,6 +1052,13 @@ uart3: serial@fc008000 {
uart4: serial@fc00c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfc00c000 0x100>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(43))>,
<&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(44))>;
dma-names = "tx", "rx";
interrupts = <28 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&uart4_clk>;
clock-names = "usart";
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment