Commit b6ef4c2c authored by Maxime Ripard's avatar Maxime Ripard

ARM: sun4i: ba10 tvbox: Convert to DT label based syntax

In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
parent 84bdea6e
...@@ -54,95 +54,93 @@ ...@@ -54,95 +54,93 @@
/ { / {
model = "BA10 tvbox"; model = "BA10 tvbox";
compatible = "allwinner,ba10-tvbox", "allwinner,sun4i-a10"; compatible = "allwinner,ba10-tvbox", "allwinner,sun4i-a10";
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
soc@01c00000 { &i2c0 {
emac: ethernet@01c0b000 { pinctrl-names = "default";
pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins_a>;
pinctrl-0 = <&emac_pins_a>; status = "okay";
phy = <&phy1>;
status = "okay"; axp209: pmic@34 {
}; compatible = "x-powers,axp209";
reg = <0x34>;
mdio@01c0b080 { interrupts = <0>;
status = "okay";
interrupt-controller;
phy1: ethernet-phy@1 { #interrupt-cells = <1>;
reg = <1>;
};
};
mmc0: mmc@01c0f000 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
cd-inverted;
status = "okay";
};
usbphy: phy@01c13400 {
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb2_vbus>;
status = "okay";
};
ehci0: usb@01c14000 {
status = "okay";
};
ohci0: usb@01c14400 {
status = "okay";
};
ehci1: usb@01c1c000 {
status = "okay";
};
ohci1: usb@01c1c400 {
status = "okay";
};
pinctrl@01c20800 {
usb2_vbus_pin_a: usb2_vbus_pin@0 {
allwinner,pins = "PH12";
};
};
ir0: ir@01c21800 {
pinctrl-names = "default";
pinctrl-0 = <&ir0_pins_a>;
status = "okay";
};
uart0: serial@01c28000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
i2c0: i2c@01c2ac00 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
compatible = "x-powers,axp209";
reg = <0x34>;
interrupts = <0>;
interrupt-controller;
#interrupt-cells = <1>;
};
};
}; };
};
reg_usb1_vbus: usb1-vbus { &ir0 {
status = "okay"; pinctrl-names = "default";
pinctrl-0 = <&ir0_pins_a>;
status = "okay";
};
&mdio {
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
}; };
};
reg_usb2_vbus: usb2-vbus { &mmc0 {
gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>; pinctrl-names = "default";
status = "okay"; pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
cd-inverted;
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&pio {
usb2_vbus_pin_a: usb2_vbus_pin@0 {
allwinner,pins = "PH12";
}; };
}; };
&reg_usb1_vbus {
status = "okay";
};
&reg_usb2_vbus {
gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&usbphy {
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb2_vbus>;
status = "okay";
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment