arm64: dts: rockchip: add mmc nodes for rk3328 evaluation board

Rockchip's rk3328 evaluation board has 3 mmc controllers for
sdio/sdmmc/emmc, let's enable them.
Signed-off-by: Liang Chen <cl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

arch/arm64/boot/dts/rockchip/rk3328-evb.dts

@@ -60,6 +60,31 @@ dc_12v: dc-12v {
 		regulator-max-microvolt = <12000000>;
 	};
 
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+
+		/*
+		 * On the module itself this is one of these (depending
+		 * on the actual card populated):
+		 * - SDIO_RESET_L_WL_REG_ON
+		 * - PDN (power down when low)
+		 */
+		reset-gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+	};
+
+	vcc_sd: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio0 30 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc0m1_gpio>;
+		regulator-name = "vcc_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_io>;
+	};
+
 	vcc_sys: vcc-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc_sys";
@@ -78,6 +103,15 @@ vcc_phy: vcc-phy-regulator {
 	};
 };
 
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+	status = "okay";
+};
+
 &gmac2phy {
 	phy-supply = <&vcc_phy>;
 	clock_in_out = "output";
@@ -85,7 +119,7 @@ &gmac2phy {
 	assigned-clock-rate = <50000000>;
 	assigned-clocks = <&cru SCLK_MAC2PHY>;
 	assigned-clock-parents = <&cru SCLK_MAC2PHY_SRC>;
-	status = "okay";
+
 };
 
 &i2c1 {
@@ -203,6 +237,38 @@ pmic_int_l: pmic-int-l {
 			rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+		rockchip,pins =
+			<1 18 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&sdio {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	max-frequency = <150000000>;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	disable-wp;
+	max-frequency = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
+	vmmc-supply = <&vcc_sd>;
+	status = "okay";
 };
 
 &tsadc {