at91: switch to CLKDEV_LOOKUP

we do not change the clock naming convention so does not need to switch
the AVR32 yet
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>

arch/arm/Kconfig

@@ -294,6 +294,7 @@ config ARCH_AT91
 	bool "Atmel AT91"
 	select ARCH_REQUIRE_GPIOLIB
 	select HAVE_CLK
+	select CLKDEV_LOOKUP
 	help
 	  This enables support for systems based on the Atmel AT91RM9200,
 	  AT91SAM9 and AT91CAP9 processors.

arch/arm/mach-at91/at572d940hf.c

@@ -205,6 +205,21 @@ static struct clk *periph_clocks[] __initdata = {
 	/* irq0 .. irq2 */
 };
 
+static struct clk_lookup periph_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
+	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
+	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
+	CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.0", &tc1_clk),
+	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk),
+};
+
+static struct clk_lookup usart_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
+};
+
 /*
  * The five programmable clocks.
  * You must configure pin multiplexing to bring these signals out.
@@ -262,6 +277,11 @@ static void __init at572d940hf_register_clocks(void)
 	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
 		clk_register(periph_clocks[i]);
 
+	clkdev_add_table(periph_clocks_lookups,
+			 ARRAY_SIZE(periph_clocks_lookups));
+	clkdev_add_table(usart_clocks_lookups,
+			 ARRAY_SIZE(usart_clocks_lookups));
+
 	clk_register(&pck0);
 	clk_register(&pck1);
 	clk_register(&pck2);
@@ -272,6 +292,18 @@ static void __init at572d940hf_register_clocks(void)
 	clk_register(&hck1);
 }
 
+static struct clk_lookup console_clock_lookup;
+
+void __init at572d940hf_set_console_clock(int id)
+{
+	if (id >= ARRAY_SIZE(usart_clocks_lookups))
+		return;
+
+	console_clock_lookup.con_id = "usart";
+	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
+	clkdev_add(&console_clock_lookup);
+}
+
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */

arch/arm/mach-at91/at572d940hf_devices.c

@@ -532,7 +532,6 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		at91_set_A_periph(AT91_PIN_PA1, 0);	/* SPI0_MOSI */
 		at91_set_A_periph(AT91_PIN_PA2, 0);	/* SPI0_SPCK */
 
-		at91_clock_associate("spi0_clk", &at572d940hf_spi0_device.dev, "spi_clk");
 		platform_device_register(&at572d940hf_spi0_device);
 	}
 	if (enable_spi1) {
@@ -540,7 +539,6 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		at91_set_A_periph(AT91_PIN_PC1, 0);	/* SPI1_MOSI */
 		at91_set_A_periph(AT91_PIN_PC2, 0);	/* SPI1_SPCK */
 
-		at91_clock_associate("spi1_clk", &at572d940hf_spi1_device.dev, "spi_clk");
 		platform_device_register(&at572d940hf_spi1_device);
 	}
 }
@@ -587,10 +585,6 @@ static struct platform_device at572d940hf_tcb_device = {
 
 static void __init at91_add_device_tc(void)
 {
-	/* this chip has a separate clock and irq for each TC channel */
-	at91_clock_associate("tc0_clk", &at572d940hf_tcb_device.dev, "t0_clk");
-	at91_clock_associate("tc1_clk", &at572d940hf_tcb_device.dev, "t1_clk");
-	at91_clock_associate("tc2_clk", &at572d940hf_tcb_device.dev, "t2_clk");
 	platform_device_register(&at572d940hf_tcb_device);
 }
 #else
@@ -828,22 +822,18 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 		case 0:		/* DBGU */
 			pdev = &at572d940hf_dbgu_device;
 			configure_dbgu_pins();
-			at91_clock_associate("mck", &pdev->dev, "usart");
 			break;
 		case AT572D940HF_ID_US0:
 			pdev = &at572d940hf_uart0_device;
 			configure_usart0_pins(pins);
-			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
 			break;
 		case AT572D940HF_ID_US1:
 			pdev = &at572d940hf_uart1_device;
 			configure_usart1_pins(pins);
-			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
 			break;
 		case AT572D940HF_ID_US2:
 			pdev = &at572d940hf_uart2_device;
 			configure_usart2_pins(pins);
-			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
 			break;
 		default:
 			return;
@@ -857,8 +847,10 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 
 void __init at91_set_serial_console(unsigned portnr)
 {
-	if (portnr < ATMEL_MAX_UART)
+	if (portnr < ATMEL_MAX_UART) {
 		atmel_default_console_device = at91_uarts[portnr];
+		at572d940hf_set_console_clock(portnr);
+	}
 }
 
 void __init at91_add_device_serial(void)

arch/arm/mach-at91/at91cap9.c

@@ -222,6 +222,25 @@ static struct clk *periph_clocks[] __initdata = {
 	// irq0 .. irq1
 };
 
+static struct clk_lookup periph_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("hclk", "atmel_usba_udc.0", &utmi_clk),
+	CLKDEV_CON_DEV_ID("pclk", "atmel_usba_udc.0", &udphs_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.1", &mmc1_clk),
+	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
+	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
+	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk),
+	CLKDEV_CON_DEV_ID("ssc", "ssc.0", &ssc0_clk),
+	CLKDEV_CON_DEV_ID("ssc", "ssc.1", &ssc1_clk),
+};
+
+static struct clk_lookup usart_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
+};
+
 /*
  * The four programmable clocks.
  * You must configure pin multiplexing to bring these signals out.
@@ -258,12 +277,29 @@ static void __init at91cap9_register_clocks(void)
 	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
 		clk_register(periph_clocks[i]);
 
+	clkdev_add_table(periph_clocks_lookups,
+			 ARRAY_SIZE(periph_clocks_lookups));
+	clkdev_add_table(usart_clocks_lookups,
+			 ARRAY_SIZE(usart_clocks_lookups));
+
 	clk_register(&pck0);
 	clk_register(&pck1);
 	clk_register(&pck2);
 	clk_register(&pck3);
 }
 
+static struct clk_lookup console_clock_lookup;
+
+void __init at91cap9_set_console_clock(int id)
+{
+	if (id >= ARRAY_SIZE(usart_clocks_lookups))
+		return;
+
+	console_clock_lookup.con_id = "usart";
+	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
+	clkdev_add(&console_clock_lookup);
+}
+
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */

arch/arm/mach-at91/at91cap9_devices.c

@@ -181,10 +181,6 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 
 	/* Pullup pin is handled internally by USB device peripheral */
 
-	/* Clocks */
-	at91_clock_associate("utmi_clk", &at91_usba_udc_device.dev, "hclk");
-	at91_clock_associate("udphs_clk", &at91_usba_udc_device.dev, "pclk");
-
 	platform_device_register(&at91_usba_udc_device);
 }
 #else
@@ -355,7 +351,6 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		}
 
 		mmc0_data = *data;
-		at91_clock_associate("mci0_clk", &at91cap9_mmc0_device.dev, "mci_clk");
 		platform_device_register(&at91cap9_mmc0_device);
 	} else {			/* MCI1 */
 		/* CLK */
@@ -373,7 +368,6 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		}
 
 		mmc1_data = *data;
-		at91_clock_associate("mci1_clk", &at91cap9_mmc1_device.dev, "mci_clk");
 		platform_device_register(&at91cap9_mmc1_device);
 	}
 }
@@ -614,7 +608,6 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		at91_set_B_periph(AT91_PIN_PA1, 0);	/* SPI0_MOSI */
 		at91_set_B_periph(AT91_PIN_PA2, 0);	/* SPI0_SPCK */
 
-		at91_clock_associate("spi0_clk", &at91cap9_spi0_device.dev, "spi_clk");
 		platform_device_register(&at91cap9_spi0_device);
 	}
 	if (enable_spi1) {
@@ -622,7 +615,6 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		at91_set_A_periph(AT91_PIN_PB13, 0);	/* SPI1_MOSI */
 		at91_set_A_periph(AT91_PIN_PB14, 0);	/* SPI1_SPCK */
 
-		at91_clock_associate("spi1_clk", &at91cap9_spi1_device.dev, "spi_clk");
 		platform_device_register(&at91cap9_spi1_device);
 	}
 }
@@ -659,8 +651,6 @@ static struct platform_device at91cap9_tcb_device = {
 
 static void __init at91_add_device_tc(void)
 {
-	/* this chip has one clock and irq for all three TC channels */
-	at91_clock_associate("tcb_clk", &at91cap9_tcb_device.dev, "t0_clk");
 	platform_device_register(&at91cap9_tcb_device);
 }
 #else
@@ -1001,12 +991,10 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins)
 	case AT91CAP9_ID_SSC0:
 		pdev = &at91cap9_ssc0_device;
 		configure_ssc0_pins(pins);
-		at91_clock_associate("ssc0_clk", &pdev->dev, "ssc");
 		break;
 	case AT91CAP9_ID_SSC1:
 		pdev = &at91cap9_ssc1_device;
 		configure_ssc1_pins(pins);
-		at91_clock_associate("ssc1_clk", &pdev->dev, "ssc");
 		break;
 	default:
 		return;
@@ -1205,22 +1193,18 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 		case 0:		/* DBGU */
 			pdev = &at91cap9_dbgu_device;
 			configure_dbgu_pins();
-			at91_clock_associate("mck", &pdev->dev, "usart");
 			break;
 		case AT91CAP9_ID_US0:
 			pdev = &at91cap9_uart0_device;
 			configure_usart0_pins(pins);
-			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
 			break;
 		case AT91CAP9_ID_US1:
 			pdev = &at91cap9_uart1_device;
 			configure_usart1_pins(pins);
-			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
 			break;
 		case AT91CAP9_ID_US2:
 			pdev = &at91cap9_uart2_device;
 			configure_usart2_pins(pins);
-			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
 			break;
 		default:
 			return;
@@ -1234,8 +1218,10 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 
 void __init at91_set_serial_console(unsigned portnr)
 {
-	if (portnr < ATMEL_MAX_UART)
+	if (portnr < ATMEL_MAX_UART) {
 		atmel_default_console_device = at91_uarts[portnr];
+		at91cap9_set_console_clock(portnr);
+	}
 }
 
 void __init at91_add_device_serial(void)

arch/arm/mach-at91/at91rm9200.c

@@ -191,6 +191,26 @@ static struct clk *periph_clocks[] __initdata = {
 	// irq0 .. irq6
 };
 
+static struct clk_lookup periph_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
+	CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.0", &tc1_clk),
+	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk),
+	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.1", &tc3_clk),
+	CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.1", &tc4_clk),
+	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.1", &tc5_clk),
+	CLKDEV_CON_DEV_ID("ssc", "ssc.0", &ssc0_clk),
+	CLKDEV_CON_DEV_ID("ssc", "ssc.1", &ssc1_clk),
+	CLKDEV_CON_DEV_ID("ssc", "ssc.2", &ssc2_clk),
+};
+
+static struct clk_lookup usart_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.4", &usart3_clk),
+};
+
 /*
  * The four programmable clocks.
  * You must configure pin multiplexing to bring these signals out.
@@ -227,12 +247,29 @@ static void __init at91rm9200_register_clocks(void)
 	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
 		clk_register(periph_clocks[i]);
 
+	clkdev_add_table(periph_clocks_lookups,
+			 ARRAY_SIZE(periph_clocks_lookups));
+	clkdev_add_table(usart_clocks_lookups,
+			 ARRAY_SIZE(usart_clocks_lookups));
+
 	clk_register(&pck0);
 	clk_register(&pck1);
 	clk_register(&pck2);
 	clk_register(&pck3);
 }
 
+static struct clk_lookup console_clock_lookup;
+
+void __init at91rm9200_set_console_clock(int id)
+{
+	if (id >= ARRAY_SIZE(usart_clocks_lookups))
+		return;
+
+	console_clock_lookup.con_id = "usart";
+	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
+	clkdev_add(&console_clock_lookup);
+}
+
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */

arch/arm/mach-at91/at91rm9200_devices.c

@@ -644,15 +644,7 @@ static struct platform_device at91rm9200_tcb1_device = {
 
 static void __init at91_add_device_tc(void)
 {
-	/* this chip has a separate clock and irq for each TC channel */
-	at91_clock_associate("tc0_clk", &at91rm9200_tcb0_device.dev, "t0_clk");
-	at91_clock_associate("tc1_clk", &at91rm9200_tcb0_device.dev, "t1_clk");
-	at91_clock_associate("tc2_clk", &at91rm9200_tcb0_device.dev, "t2_clk");
 	platform_device_register(&at91rm9200_tcb0_device);
-
-	at91_clock_associate("tc3_clk", &at91rm9200_tcb1_device.dev, "t0_clk");
-	at91_clock_associate("tc4_clk", &at91rm9200_tcb1_device.dev, "t1_clk");
-	at91_clock_associate("tc5_clk", &at91rm9200_tcb1_device.dev, "t2_clk");
 	platform_device_register(&at91rm9200_tcb1_device);
 }
 #else
@@ -849,17 +841,14 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins)
 	case AT91RM9200_ID_SSC0:
 		pdev = &at91rm9200_ssc0_device;
 		configure_ssc0_pins(pins);
-		at91_clock_associate("ssc0_clk", &pdev->dev, "ssc");
 		break;
 	case AT91RM9200_ID_SSC1:
 		pdev = &at91rm9200_ssc1_device;
 		configure_ssc1_pins(pins);
-		at91_clock_associate("ssc1_clk", &pdev->dev, "ssc");
 		break;
 	case AT91RM9200_ID_SSC2:
 		pdev = &at91rm9200_ssc2_device;
 		configure_ssc2_pins(pins);
-		at91_clock_associate("ssc2_clk", &pdev->dev, "ssc");
 		break;
 	default:
 		return;
@@ -1115,27 +1104,22 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 		case 0:		/* DBGU */
 			pdev = &at91rm9200_dbgu_device;
 			configure_dbgu_pins();
-			at91_clock_associate("mck", &pdev->dev, "usart");
 			break;
 		case AT91RM9200_ID_US0:
 			pdev = &at91rm9200_uart0_device;
 			configure_usart0_pins(pins);
-			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
 			break;
 		case AT91RM9200_ID_US1:
 			pdev = &at91rm9200_uart1_device;
 			configure_usart1_pins(pins);
-			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
 			break;
 		case AT91RM9200_ID_US2:
 			pdev = &at91rm9200_uart2_device;
 			configure_usart2_pins(pins);
-			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
 			break;
 		case AT91RM9200_ID_US3:
 			pdev = &at91rm9200_uart3_device;
 			configure_usart3_pins(pins);
-			at91_clock_associate("usart3_clk", &pdev->dev, "usart");
 			break;
 		default:
 			return;
@@ -1149,8 +1133,10 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 
 void __init at91_set_serial_console(unsigned portnr)
 {
-	if (portnr < ATMEL_MAX_UART)
+	if (portnr < ATMEL_MAX_UART) {
 		atmel_default_console_device = at91_uarts[portnr];
+		at91rm9200_set_console_clock(portnr);
+	}
 }
 
 void __init at91_add_device_serial(void)

arch/arm/mach-at91/at91sam9260.c

@@ -231,6 +231,28 @@ static struct clk *periph_clocks[] __initdata = {
 	// irq0 .. irq2
 };
 
+static struct clk_lookup periph_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
+	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
+	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
+	CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.0", &tc1_clk),
+	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk),
+	CLKDEV_CON_DEV_ID("t3_clk", "atmel_tcb.1", &tc3_clk),
+	CLKDEV_CON_DEV_ID("t4_clk", "atmel_tcb.1", &tc4_clk),
+	CLKDEV_CON_DEV_ID("t5_clk", "atmel_tcb.1", &tc5_clk),
+	CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc_clk),
+};
+
+static struct clk_lookup usart_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.4", &usart3_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.5", &usart4_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.6", &usart5_clk),
+};
+
 /*
  * The two programmable clocks.
  * You must configure pin multiplexing to bring these signals out.
@@ -255,10 +277,27 @@ static void __init at91sam9260_register_clocks(void)
 	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
 		clk_register(periph_clocks[i]);
 
+	clkdev_add_table(periph_clocks_lookups,
+			 ARRAY_SIZE(periph_clocks_lookups));
+	clkdev_add_table(usart_clocks_lookups,
+			 ARRAY_SIZE(usart_clocks_lookups));
+
 	clk_register(&pck0);
 	clk_register(&pck1);
 }
 
+static struct clk_lookup console_clock_lookup;
+
+void __init at91sam9260_set_console_clock(int id)
+{
+	if (id >= ARRAY_SIZE(usart_clocks_lookups))
+		return;
+
+	console_clock_lookup.con_id = "usart";
+	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
+	clkdev_add(&console_clock_lookup);
+}
+
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */

arch/arm/mach-at91/at91sam9260_devices.c

@@ -609,7 +609,6 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		at91_set_A_periph(AT91_PIN_PA1, 0);	/* SPI0_MOSI */
 		at91_set_A_periph(AT91_PIN_PA2, 0);	/* SPI1_SPCK */
 
-		at91_clock_associate("spi0_clk", &at91sam9260_spi0_device.dev, "spi_clk");
 		platform_device_register(&at91sam9260_spi0_device);
 	}
 	if (enable_spi1) {
@@ -617,7 +616,6 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		at91_set_A_periph(AT91_PIN_PB1, 0);	/* SPI1_MOSI */
 		at91_set_A_periph(AT91_PIN_PB2, 0);	/* SPI1_SPCK */
 
-		at91_clock_associate("spi1_clk", &at91sam9260_spi1_device.dev, "spi_clk");
 		platform_device_register(&at91sam9260_spi1_device);
 	}
 }
@@ -694,15 +692,7 @@ static struct platform_device at91sam9260_tcb1_device = {
 
 static void __init at91_add_device_tc(void)
 {
-	/* this chip has a separate clock and irq for each TC channel */
-	at91_clock_associate("tc0_clk", &at91sam9260_tcb0_device.dev, "t0_clk");
-	at91_clock_associate("tc1_clk", &at91sam9260_tcb0_device.dev, "t1_clk");
-	at91_clock_associate("tc2_clk", &at91sam9260_tcb0_device.dev, "t2_clk");
 	platform_device_register(&at91sam9260_tcb0_device);
-
-	at91_clock_associate("tc3_clk", &at91sam9260_tcb1_device.dev, "t0_clk");
-	at91_clock_associate("tc4_clk", &at91sam9260_tcb1_device.dev, "t1_clk");
-	at91_clock_associate("tc5_clk", &at91sam9260_tcb1_device.dev, "t2_clk");
 	platform_device_register(&at91sam9260_tcb1_device);
 }
 #else
@@ -820,7 +810,6 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins)
 	case AT91SAM9260_ID_SSC:
 		pdev = &at91sam9260_ssc_device;
 		configure_ssc_pins(pins);
-		at91_clock_associate("ssc_clk", &pdev->dev, "pclk");
 		break;
 	default:
 		return;
@@ -1145,37 +1134,30 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 		case 0:		/* DBGU */
 			pdev = &at91sam9260_dbgu_device;
 			configure_dbgu_pins();
-			at91_clock_associate("mck", &pdev->dev, "usart");
 			break;
 		case AT91SAM9260_ID_US0:
 			pdev = &at91sam9260_uart0_device;
 			configure_usart0_pins(pins);
-			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9260_ID_US1:
 			pdev = &at91sam9260_uart1_device;
 			configure_usart1_pins(pins);
-			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9260_ID_US2:
 			pdev = &at91sam9260_uart2_device;
 			configure_usart2_pins(pins);
-			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9260_ID_US3:
 			pdev = &at91sam9260_uart3_device;
 			configure_usart3_pins(pins);
-			at91_clock_associate("usart3_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9260_ID_US4:
 			pdev = &at91sam9260_uart4_device;
 			configure_usart4_pins();
-			at91_clock_associate("usart4_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9260_ID_US5:
 			pdev = &at91sam9260_uart5_device;
 			configure_usart5_pins();
-			at91_clock_associate("usart5_clk", &pdev->dev, "usart");
 			break;
 		default:
 			return;
@@ -1189,8 +1171,10 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 
 void __init at91_set_serial_console(unsigned portnr)
 {
-	if (portnr < ATMEL_MAX_UART)
+	if (portnr < ATMEL_MAX_UART) {
 		atmel_default_console_device = at91_uarts[portnr];
+		at91sam9260_set_console_clock(portnr);
+	}
 }
 
 void __init at91_add_device_serial(void)

arch/arm/mach-at91/at91sam9261.c

@@ -178,6 +178,24 @@ static struct clk *periph_clocks[] __initdata = {
 	// irq0 .. irq2
 };
 
+static struct clk_lookup periph_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
+	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
+	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
+	CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.0", &tc1_clk),
+	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc1_clk),
+	CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
+	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
+	CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk),
+};
+
+static struct clk_lookup usart_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
+};
+
 /*
  * The four programmable clocks.
  * You must configure pin multiplexing to bring these signals out.
@@ -228,6 +246,11 @@ static void __init at91sam9261_register_clocks(void)
 	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
 		clk_register(periph_clocks[i]);
 
+	clkdev_add_table(periph_clocks_lookups,
+			 ARRAY_SIZE(periph_clocks_lookups));
+	clkdev_add_table(usart_clocks_lookups,
+			 ARRAY_SIZE(usart_clocks_lookups));
+
 	clk_register(&pck0);
 	clk_register(&pck1);
 	clk_register(&pck2);
@@ -237,6 +260,18 @@ static void __init at91sam9261_register_clocks(void)
 	clk_register(&hck1);
 }
 
+static struct clk_lookup console_clock_lookup;
+
+void __init at91sam9261_set_console_clock(int id)
+{
+	if (id >= ARRAY_SIZE(usart_clocks_lookups))
+		return;
+
+	console_clock_lookup.con_id = "usart";
+	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
+	clkdev_add(&console_clock_lookup);
+}
+
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */

arch/arm/mach-at91/at91sam9261_devices.c

@@ -426,7 +426,6 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		at91_set_A_periph(AT91_PIN_PA1, 0);	/* SPI0_MOSI */
 		at91_set_A_periph(AT91_PIN_PA2, 0);	/* SPI0_SPCK */
 
-		at91_clock_associate("spi0_clk", &at91sam9261_spi0_device.dev, "spi_clk");
 		platform_device_register(&at91sam9261_spi0_device);
 	}
 	if (enable_spi1) {
@@ -434,7 +433,6 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		at91_set_A_periph(AT91_PIN_PB31, 0);	/* SPI1_MOSI */
 		at91_set_A_periph(AT91_PIN_PB29, 0);	/* SPI1_SPCK */
 
-		at91_clock_associate("spi1_clk", &at91sam9261_spi1_device.dev, "spi_clk");
 		platform_device_register(&at91sam9261_spi1_device);
 	}
 }
@@ -581,10 +579,6 @@ static struct platform_device at91sam9261_tcb_device = {
 
 static void __init at91_add_device_tc(void)
 {
-	/* this chip has a separate clock and irq for each TC channel */
-	at91_clock_associate("tc0_clk", &at91sam9261_tcb_device.dev, "t0_clk");
-	at91_clock_associate("tc1_clk", &at91sam9261_tcb_device.dev, "t1_clk");
-	at91_clock_associate("tc2_clk", &at91sam9261_tcb_device.dev, "t2_clk");
 	platform_device_register(&at91sam9261_tcb_device);
 }
 #else
@@ -786,17 +780,14 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins)
 	case AT91SAM9261_ID_SSC0:
 		pdev = &at91sam9261_ssc0_device;
 		configure_ssc0_pins(pins);
-		at91_clock_associate("ssc0_clk", &pdev->dev, "pclk");
 		break;
 	case AT91SAM9261_ID_SSC1:
 		pdev = &at91sam9261_ssc1_device;
 		configure_ssc1_pins(pins);
-		at91_clock_associate("ssc1_clk", &pdev->dev, "pclk");
 		break;
 	case AT91SAM9261_ID_SSC2:
 		pdev = &at91sam9261_ssc2_device;
 		configure_ssc2_pins(pins);
-		at91_clock_associate("ssc2_clk", &pdev->dev, "pclk");
 		break;
 	default:
 		return;
@@ -995,22 +986,18 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 		case 0:		/* DBGU */
 			pdev = &at91sam9261_dbgu_device;
 			configure_dbgu_pins();
-			at91_clock_associate("mck", &pdev->dev, "usart");
 			break;
 		case AT91SAM9261_ID_US0:
 			pdev = &at91sam9261_uart0_device;
 			configure_usart0_pins(pins);
-			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9261_ID_US1:
 			pdev = &at91sam9261_uart1_device;
 			configure_usart1_pins(pins);
-			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9261_ID_US2:
 			pdev = &at91sam9261_uart2_device;
 			configure_usart2_pins(pins);
-			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
 			break;
 		default:
 			return;
@@ -1024,8 +1011,10 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 
 void __init at91_set_serial_console(unsigned portnr)
 {
-	if (portnr < ATMEL_MAX_UART)
+	if (portnr < ATMEL_MAX_UART) {
 		atmel_default_console_device = at91_uarts[portnr];
+		at91sam9261_set_console_clock(portnr);
+	}
 }
 
 void __init at91_add_device_serial(void)

arch/arm/mach-at91/at91sam9263.c

@@ -199,6 +199,23 @@ static struct clk *periph_clocks[] __initdata = {
 	// irq0 .. irq1
 };
 
+static struct clk_lookup periph_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
+	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.1", &mmc1_clk),
+	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
+	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
+	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk),
+};
+
+static struct clk_lookup usart_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
+};
+
 /*
  * The four programmable clocks.
  * You must configure pin multiplexing to bring these signals out.
@@ -235,12 +252,29 @@ static void __init at91sam9263_register_clocks(void)
 	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
 		clk_register(periph_clocks[i]);
 
+	clkdev_add_table(periph_clocks_lookups,
+			 ARRAY_SIZE(periph_clocks_lookups));
+	clkdev_add_table(usart_clocks_lookups,
+			 ARRAY_SIZE(usart_clocks_lookups));
+
 	clk_register(&pck0);
 	clk_register(&pck1);
 	clk_register(&pck2);
 	clk_register(&pck3);
 }
 
+static struct clk_lookup console_clock_lookup;
+
+void __init at91sam9263_set_console_clock(int id)
+{
+	if (id >= ARRAY_SIZE(usart_clocks_lookups))
+		return;
+
+	console_clock_lookup.con_id = "usart";
+	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
+	clkdev_add(&console_clock_lookup);
+}
+
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */

arch/arm/mach-at91/at91sam9263_devices.c

@@ -308,7 +308,6 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		}
 
 		mmc0_data = *data;
-		at91_clock_associate("mci0_clk", &at91sam9263_mmc0_device.dev, "mci_clk");
 		platform_device_register(&at91sam9263_mmc0_device);
 	} else {			/* MCI1 */
 		/* CLK */
@@ -339,7 +338,6 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		}
 
 		mmc1_data = *data;
-		at91_clock_associate("mci1_clk", &at91sam9263_mmc1_device.dev, "mci_clk");
 		platform_device_register(&at91sam9263_mmc1_device);
 	}
 }
@@ -686,7 +684,6 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		at91_set_B_periph(AT91_PIN_PA1, 0);	/* SPI0_MOSI */
 		at91_set_B_periph(AT91_PIN_PA2, 0);	/* SPI0_SPCK */
 
-		at91_clock_associate("spi0_clk", &at91sam9263_spi0_device.dev, "spi_clk");
 		platform_device_register(&at91sam9263_spi0_device);
 	}
 	if (enable_spi1) {
@@ -694,7 +691,6 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		at91_set_A_periph(AT91_PIN_PB13, 0);	/* SPI1_MOSI */
 		at91_set_A_periph(AT91_PIN_PB14, 0);	/* SPI1_SPCK */
 
-		at91_clock_associate("spi1_clk", &at91sam9263_spi1_device.dev, "spi_clk");
 		platform_device_register(&at91sam9263_spi1_device);
 	}
 }
@@ -941,8 +937,6 @@ static struct platform_device at91sam9263_tcb_device = {
 
 static void __init at91_add_device_tc(void)
 {
-	/* this chip has one clock and irq for all three TC channels */
-	at91_clock_associate("tcb_clk", &at91sam9263_tcb_device.dev, "t0_clk");
 	platform_device_register(&at91sam9263_tcb_device);
 }
 #else
@@ -1171,12 +1165,10 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins)
 	case AT91SAM9263_ID_SSC0:
 		pdev = &at91sam9263_ssc0_device;
 		configure_ssc0_pins(pins);
-		at91_clock_associate("ssc0_clk", &pdev->dev, "pclk");
 		break;
 	case AT91SAM9263_ID_SSC1:
 		pdev = &at91sam9263_ssc1_device;
 		configure_ssc1_pins(pins);
-		at91_clock_associate("ssc1_clk", &pdev->dev, "pclk");
 		break;
 	default:
 		return;
@@ -1376,22 +1368,18 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 		case 0:		/* DBGU */
 			pdev = &at91sam9263_dbgu_device;
 			configure_dbgu_pins();
-			at91_clock_associate("mck", &pdev->dev, "usart");
 			break;
 		case AT91SAM9263_ID_US0:
 			pdev = &at91sam9263_uart0_device;
 			configure_usart0_pins(pins);
-			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9263_ID_US1:
 			pdev = &at91sam9263_uart1_device;
 			configure_usart1_pins(pins);
-			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9263_ID_US2:
 			pdev = &at91sam9263_uart2_device;
 			configure_usart2_pins(pins);
-			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
 			break;
 		default:
 			return;
@@ -1405,8 +1393,10 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 
 void __init at91_set_serial_console(unsigned portnr)
 {
-	if (portnr < ATMEL_MAX_UART)
+	if (portnr < ATMEL_MAX_UART) {
 		atmel_default_console_device = at91_uarts[portnr];
+		at91sam9263_set_console_clock(portnr);
+	}
 }
 
 void __init at91_add_device_serial(void)

arch/arm/mach-at91/at91sam9g45.c

@@ -184,22 +184,6 @@ static struct clk vdec_clk = {
 	.type		= CLK_TYPE_PERIPHERAL,
 };
 
-/* One additional fake clock for ohci */
-static struct clk ohci_clk = {
-	.name		= "ohci_clk",
-	.pmc_mask	= 0,
-	.type		= CLK_TYPE_PERIPHERAL,
-	.parent		= &uhphs_clk,
-};
-
-/* One additional fake clock for second TC block */
-static struct clk tcb1_clk = {
-	.name		= "tcb1_clk",
-	.pmc_mask	= 0,
-	.type		= CLK_TYPE_PERIPHERAL,
-	.parent		= &tcb0_clk,
-};
-
 static struct clk *periph_clocks[] __initdata = {
 	&pioA_clk,
 	&pioB_clk,
@@ -228,8 +212,30 @@ static struct clk *periph_clocks[] __initdata = {
 	&udphs_clk,
 	&mmc1_clk,
 	// irq0
-	&ohci_clk,
-	&tcb1_clk,
+};
+
+static struct clk_lookup periph_clocks_lookups[] = {
+	/* One additional fake clock for ohci */
+	CLKDEV_CON_ID("ohci_clk", &uhphs_clk),
+	CLKDEV_CON_DEV_ID("ehci_clk", "atmel-ehci.0", &uhphs_clk),
+	CLKDEV_CON_DEV_ID("hclk", "atmel_usba_udc.0", &utmi_clk),
+	CLKDEV_CON_DEV_ID("pclk", "atmel_usba_udc.0", &udphs_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.1", &mmc1_clk),
+	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
+	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
+	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb0_clk),
+	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.1", &tcb0_clk),
+	CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
+	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
+};
+
+static struct clk_lookup usart_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.4", &usart3_clk),
 };
 
 /*
@@ -256,6 +262,11 @@ static void __init at91sam9g45_register_clocks(void)
 	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
 		clk_register(periph_clocks[i]);
 
+	clkdev_add_table(periph_clocks_lookups,
+			 ARRAY_SIZE(periph_clocks_lookups));
+	clkdev_add_table(usart_clocks_lookups,
+			 ARRAY_SIZE(usart_clocks_lookups));
+
 	if (cpu_is_at91sam9m10() || cpu_is_at91sam9m11())
 		clk_register(&vdec_clk);
 
@@ -263,6 +274,18 @@ static void __init at91sam9g45_register_clocks(void)
 	clk_register(&pck1);
 }
 
+static struct clk_lookup console_clock_lookup;
+
+void __init at91sam9g45_set_console_clock(int id)
+{
+	if (id >= ARRAY_SIZE(usart_clocks_lookups))
+		return;
+
+	console_clock_lookup.con_id = "usart";
+	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
+	clkdev_add(&console_clock_lookup);
+}
+
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */

arch/arm/mach-at91/at91sam9g45_devices.c

@@ -180,7 +180,6 @@ void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data)
 	}
 
 	usbh_ehci_data = *data;
-	at91_clock_associate("uhphs_clk", &at91_usbh_ehci_device.dev, "ehci_clk");
 	platform_device_register(&at91_usbh_ehci_device);
 }
 #else
@@ -266,10 +265,6 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 
 	/* Pullup pin is handled internally by USB device peripheral */
 
-	/* Clocks */
-	at91_clock_associate("utmi_clk", &at91_usba_udc_device.dev, "hclk");
-	at91_clock_associate("udphs_clk", &at91_usba_udc_device.dev, "pclk");
-
 	platform_device_register(&at91_usba_udc_device);
 }
 #else
@@ -478,7 +473,6 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 		}
 
 		mmc0_data = *data;
-		at91_clock_associate("mci0_clk", &at91sam9g45_mmc0_device.dev, "mci_clk");
 		platform_device_register(&at91sam9g45_mmc0_device);
 
 	} else {			/* MCI1 */
@@ -504,7 +498,6 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 		}
 
 		mmc1_data = *data;
-		at91_clock_associate("mci1_clk", &at91sam9g45_mmc1_device.dev, "mci_clk");
 		platform_device_register(&at91sam9g45_mmc1_device);
 
 	}
@@ -801,7 +794,6 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		at91_set_A_periph(AT91_PIN_PB1, 0);	/* SPI0_MOSI */
 		at91_set_A_periph(AT91_PIN_PB2, 0);	/* SPI0_SPCK */
 
-		at91_clock_associate("spi0_clk", &at91sam9g45_spi0_device.dev, "spi_clk");
 		platform_device_register(&at91sam9g45_spi0_device);
 	}
 	if (enable_spi1) {
@@ -809,7 +801,6 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 		at91_set_A_periph(AT91_PIN_PB15, 0);	/* SPI1_MOSI */
 		at91_set_A_periph(AT91_PIN_PB16, 0);	/* SPI1_SPCK */
 
-		at91_clock_associate("spi1_clk", &at91sam9g45_spi1_device.dev, "spi_clk");
 		platform_device_register(&at91sam9g45_spi1_device);
 	}
 }
@@ -999,10 +990,7 @@ static struct platform_device at91sam9g45_tcb1_device = {
 
 static void __init at91_add_device_tc(void)
 {
-	/* this chip has one clock and irq for all six TC channels */
-	at91_clock_associate("tcb0_clk", &at91sam9g45_tcb0_device.dev, "t0_clk");
 	platform_device_register(&at91sam9g45_tcb0_device);
-	at91_clock_associate("tcb1_clk", &at91sam9g45_tcb1_device.dev, "t0_clk");
 	platform_device_register(&at91sam9g45_tcb1_device);
 }
 #else
@@ -1286,12 +1274,10 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins)
 	case AT91SAM9G45_ID_SSC0:
 		pdev = &at91sam9g45_ssc0_device;
 		configure_ssc0_pins(pins);
-		at91_clock_associate("ssc0_clk", &pdev->dev, "pclk");
 		break;
 	case AT91SAM9G45_ID_SSC1:
 		pdev = &at91sam9g45_ssc1_device;
 		configure_ssc1_pins(pins);
-		at91_clock_associate("ssc1_clk", &pdev->dev, "pclk");
 		break;
 	default:
 		return;
@@ -1533,27 +1519,22 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 		case 0:		/* DBGU */
 			pdev = &at91sam9g45_dbgu_device;
 			configure_dbgu_pins();
-			at91_clock_associate("mck", &pdev->dev, "usart");
 			break;
 		case AT91SAM9G45_ID_US0:
 			pdev = &at91sam9g45_uart0_device;
 			configure_usart0_pins(pins);
-			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9G45_ID_US1:
 			pdev = &at91sam9g45_uart1_device;
 			configure_usart1_pins(pins);
-			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9G45_ID_US2:
 			pdev = &at91sam9g45_uart2_device;
 			configure_usart2_pins(pins);
-			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9G45_ID_US3:
 			pdev = &at91sam9g45_uart3_device;
 			configure_usart3_pins(pins);
-			at91_clock_associate("usart3_clk", &pdev->dev, "usart");
 			break;
 		default:
 			return;
@@ -1567,8 +1548,10 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 
 void __init at91_set_serial_console(unsigned portnr)
 {
-	if (portnr < ATMEL_MAX_UART)
+	if (portnr < ATMEL_MAX_UART) {
 		atmel_default_console_device = at91_uarts[portnr];
+		at91sam9g45_set_console_clock(portnr);
+	}
 }
 
 void __init at91_add_device_serial(void)

arch/arm/mach-at91/at91sam9rl.c

@@ -190,6 +190,24 @@ static struct clk *periph_clocks[] __initdata = {
 	// irq0
 };
 
+static struct clk_lookup periph_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("hclk", "atmel_usba_udc.0", &utmi_clk),
+	CLKDEV_CON_DEV_ID("pclk", "atmel_usba_udc.0", &udphs_clk),
+	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
+	CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.0", &tc1_clk),
+	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk),
+	CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
+	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
+};
+
+static struct clk_lookup usart_clocks_lookups[] = {
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
+	CLKDEV_CON_DEV_ID("usart", "atmel_usart.4", &usart3_clk),
+};
+
 /*
  * The two programmable clocks.
  * You must configure pin multiplexing to bring these signals out.
@@ -214,10 +232,27 @@ static void __init at91sam9rl_register_clocks(void)
 	for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
 		clk_register(periph_clocks[i]);
 
+	clkdev_add_table(periph_clocks_lookups,
+			 ARRAY_SIZE(periph_clocks_lookups));
+	clkdev_add_table(usart_clocks_lookups,
+			 ARRAY_SIZE(usart_clocks_lookups));
+
 	clk_register(&pck0);
 	clk_register(&pck1);
 }
 
+static struct clk_lookup console_clock_lookup;
+
+void __init at91sam9rl_set_console_clock(int id)
+{
+	if (id >= ARRAY_SIZE(usart_clocks_lookups))
+		return;
+
+	console_clock_lookup.con_id = "usart";
+	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
+	clkdev_add(&console_clock_lookup);
+}
+
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -155,10 +155,6 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 
 	/* Pullup pin is handled internally by USB device peripheral */
 
-	/* Clocks */
-	at91_clock_associate("utmi_clk", &at91_usba_udc_device.dev, "hclk");
-	at91_clock_associate("udphs_clk", &at91_usba_udc_device.dev, "pclk");
-
 	platform_device_register(&at91_usba_udc_device);
 }
 #else
@@ -605,10 +601,6 @@ static struct platform_device at91sam9rl_tcb_device = {
 
 static void __init at91_add_device_tc(void)
 {
-	/* this chip has a separate clock and irq for each TC channel */
-	at91_clock_associate("tc0_clk", &at91sam9rl_tcb_device.dev, "t0_clk");
-	at91_clock_associate("tc1_clk", &at91sam9rl_tcb_device.dev, "t1_clk");
-	at91_clock_associate("tc2_clk", &at91sam9rl_tcb_device.dev, "t2_clk");
 	platform_device_register(&at91sam9rl_tcb_device);
 }
 #else
@@ -892,12 +884,10 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins)
 	case AT91SAM9RL_ID_SSC0:
 		pdev = &at91sam9rl_ssc0_device;
 		configure_ssc0_pins(pins);
-		at91_clock_associate("ssc0_clk", &pdev->dev, "pclk");
 		break;
 	case AT91SAM9RL_ID_SSC1:
 		pdev = &at91sam9rl_ssc1_device;
 		configure_ssc1_pins(pins);
-		at91_clock_associate("ssc1_clk", &pdev->dev, "pclk");
 		break;
 	default:
 		return;
@@ -1147,27 +1137,22 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 		case 0:		/* DBGU */
 			pdev = &at91sam9rl_dbgu_device;
 			configure_dbgu_pins();
-			at91_clock_associate("mck", &pdev->dev, "usart");
 			break;
 		case AT91SAM9RL_ID_US0:
 			pdev = &at91sam9rl_uart0_device;
 			configure_usart0_pins(pins);
-			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9RL_ID_US1:
 			pdev = &at91sam9rl_uart1_device;
 			configure_usart1_pins(pins);
-			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9RL_ID_US2:
 			pdev = &at91sam9rl_uart2_device;
 			configure_usart2_pins(pins);
-			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
 			break;
 		case AT91SAM9RL_ID_US3:
 			pdev = &at91sam9rl_uart3_device;
 			configure_usart3_pins(pins);
-			at91_clock_associate("usart3_clk", &pdev->dev, "usart");
 			break;
 		default:
 			return;
@@ -1181,8 +1166,10 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 
 void __init at91_set_serial_console(unsigned portnr)
 {
-	if (portnr < ATMEL_MAX_UART)
+	if (portnr < ATMEL_MAX_UART) {
 		atmel_default_console_device = at91_uarts[portnr];
+		at91sam9rl_set_console_clock(portnr);
+	}
 }
 
 void __init at91_add_device_serial(void)

arch/arm/mach-at91/at91x40.c

@@ -37,11 +37,6 @@ unsigned long clk_get_rate(struct clk *clk)
 	return AT91X40_MASTER_CLOCK;
 }
 
-struct clk *clk_get(struct device *dev, const char *id)
-{
-	return NULL;
-}
-
 void __init at91x40_initialize(unsigned long main_clock)
 {
 	at91_extern_irq = (1 << AT91X40_ID_IRQ0) | (1 << AT91X40_ID_IRQ1)

arch/arm/mach-at91/clock.c

@@ -163,7 +163,7 @@ static struct clk udpck = {
 	.parent		= &pllb,
 	.mode		= pmc_sys_mode,
 };
-static struct clk utmi_clk = {
+struct clk utmi_clk = {
 	.name		= "utmi_clk",
 	.parent		= &main_clk,
 	.pmc_mask	= AT91_PMC_UPLLEN,	/* in CKGR_UCKR */
@@ -182,7 +182,7 @@ static struct clk uhpck = {
  * memory, interfaces to on-chip peripherals, the AIC, and sometimes more
  * (e.g baud rate generation).  It's sourced from one of the primary clocks.
  */
-static struct clk mck = {
+struct clk mck = {
 	.name		= "mck",
 	.pmc_mask	= AT91_PMC_MCKRDY,	/* in PMC_SR */
 };
@@ -215,43 +215,6 @@ static struct clk __init *at91_css_to_clk(unsigned long css)
 	return NULL;
 }
 
-/*
- * Associate a particular clock with a function (eg, "uart") and device.
- * The drivers can then request the same 'function' with several different
- * devices and not care about which clock name to use.
- */
-void __init at91_clock_associate(const char *id, struct device *dev, const char *func)
-{
-	struct clk *clk = clk_get(NULL, id);
-
-	if (!dev || !clk || !IS_ERR(clk_get(dev, func)))
-		return;
-
-	clk->function = func;
-	clk->dev = dev;
-}
-
-/* clocks cannot be de-registered no refcounting necessary */
-struct clk *clk_get(struct device *dev, const char *id)
-{
-	struct clk *clk;
-
-	list_for_each_entry(clk, &clocks, node) {
-		if (strcmp(id, clk->name) == 0)
-			return clk;
-		if (clk->function && (dev == clk->dev) && strcmp(id, clk->function) == 0)
-			return clk;
-	}
-
-	return ERR_PTR(-ENOENT);
-}
-EXPORT_SYMBOL(clk_get);
-
-void clk_put(struct clk *clk)
-{
-}
-EXPORT_SYMBOL(clk_put);
-
 static void __clk_enable(struct clk *clk)
 {
 	if (clk->parent)
@@ -498,32 +461,38 @@ postcore_initcall(at91_clk_debugfs_init);
 /*------------------------------------------------------------------------*/
 
 /* Register a new clock */
+static void __init at91_clk_add(struct clk *clk)
+{
+	list_add_tail(&clk->node, &clocks);
+
+	clk->cl.con_id = clk->name;
+	clk->cl.clk = clk;
+	clkdev_add(&clk->cl);
+}
+
 int __init clk_register(struct clk *clk)
 {
 	if (clk_is_peripheral(clk)) {
 		if (!clk->parent)
 			clk->parent = &mck;
 		clk->mode = pmc_periph_mode;
-		list_add_tail(&clk->node, &clocks);
 	}
 	else if (clk_is_sys(clk)) {
 		clk->parent = &mck;
 		clk->mode = pmc_sys_mode;
-
-		list_add_tail(&clk->node, &clocks);
 	}
 #ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS
 	else if (clk_is_programmable(clk)) {
 		clk->mode = pmc_sys_mode;
 		init_programmable_clock(clk);
-		list_add_tail(&clk->node, &clocks);
 	}
 #endif
 
+	at91_clk_add(clk);
+
 	return 0;
 }
 
-
 /*------------------------------------------------------------------------*/
 
 static u32 __init at91_pll_rate(struct clk *pll, u32 freq, u32 reg)
@@ -754,19 +723,19 @@ int __init at91_clock_init(unsigned long main_clock)
 
 	/* Register the PMC's standard clocks */
 	for (i = 0; i < ARRAY_SIZE(standard_pmc_clocks); i++)
-		list_add_tail(&standard_pmc_clocks[i]->node, &clocks);
+		at91_clk_add(standard_pmc_clocks[i]);
 
 	if (cpu_has_pllb())
-		list_add_tail(&pllb.node, &clocks);
+		at91_clk_add(&pllb);
 
 	if (cpu_has_uhp())
-		list_add_tail(&uhpck.node, &clocks);
+		at91_clk_add(&uhpck);
 
 	if (cpu_has_udpfs())
-		list_add_tail(&udpck.node, &clocks);
+		at91_clk_add(&udpck);
 
 	if (cpu_has_utmi())
-		list_add_tail(&utmi_clk.node, &clocks);
+		at91_clk_add(&utmi_clk);
 
 	/* MCK and CPU clock are "always on" */
 	clk_enable(&mck);

arch/arm/mach-at91/clock.h

@@ -6,6 +6,8 @@
  * published by the Free Software Foundation.
  */
 
+#include <linux/clkdev.h>
+
 #define CLK_TYPE_PRIMARY	0x1
 #define CLK_TYPE_PLL		0x2
 #define CLK_TYPE_PROGRAMMABLE	0x4
@@ -16,8 +18,7 @@
 struct clk {
 	struct list_head node;
 	const char	*name;		/* unique clock name */
-	const char	*function;	/* function of the clock */
-	struct device	*dev;		/* device associated with function */
+	struct clk_lookup cl;
 	unsigned long	rate_hz;
 	struct clk	*parent;
 	u32		pmc_mask;
@@ -29,3 +30,18 @@ struct clk {
 
 
 extern int __init clk_register(struct clk *clk);
+extern struct clk mck;
+extern struct clk utmi_clk;
+
+#define CLKDEV_CON_ID(_id, _clk)			\
+	{						\
+		.con_id = _id,				\
+		.clk = _clk,				\
+	}
+
+#define CLKDEV_CON_DEV_ID(_con_id, _dev_id, _clk)	\
+	{						\
+		.con_id = _con_id,			\
+		.dev_id = _dev_id,			\
+		.clk = _clk,				\
+	}

arch/arm/mach-at91/generic.h

@@ -8,6 +8,8 @@
  * published by the Free Software Foundation.
  */
 
+#include <linux/clkdev.h>
+
  /* Map io */
 extern void __init at91rm9200_map_io(void);
 extern void __init at91sam9260_map_io(void);
@@ -50,8 +52,20 @@ extern struct sys_timer at91x40_timer;
 
  /* Clocks */
 extern int __init at91_clock_init(unsigned long main_clock);
+/*
+ * function to specify the clock of the default console. As we do not
+ * use the device/driver bus, the dev_name is not intialize. So we need
+ * to link the clock to a specific con_id only "usart"
+ */
+extern void __init at91rm9200_set_console_clock(int id);
+extern void __init at91sam9260_set_console_clock(int id);
+extern void __init at91sam9261_set_console_clock(int id);
+extern void __init at91sam9263_set_console_clock(int id);
+extern void __init at91sam9rl_set_console_clock(int id);
+extern void __init at91sam9g45_set_console_clock(int id);
+extern void __init at91cap9_set_console_clock(int id);
+extern void __init at572d940hf_set_console_clock(int id);
 struct device;
-extern void __init at91_clock_associate(const char *id, struct device *dev, const char *func);
 
  /* Power Management */
 extern void at91_irq_suspend(void);

arch/arm/mach-at91/include/mach/clkdev.h

+#ifndef __ASM_MACH_CLKDEV_H
+#define __ASM_MACH_CLKDEV_H
+
+#define __clk_get(clk) ({ 1; })
+#define __clk_put(clk) do { } while (0)
+
+#endif