Merge commit 'gcl/gcl-next'

Documentation/powerpc/booting-without-of.txt

@@ -59,6 +59,7 @@ Table of Contents
       p) Freescale Synchronous Serial Interface
 	  q) USB EHCI controllers
       r) MDIO on GPIOs
+      s) SPI busses
 
   VII - Marvell Discovery mv64[345]6x System Controller chips
     1) The /system-controller node
@@ -1883,6 +1884,62 @@ platforms are moved over to use the flattened-device-tree model.
 			 &qe_pio_c 6>;
 	};
 
+    s) SPI (Serial Peripheral Interface) busses
+
+    SPI busses can be described with a node for the SPI master device
+    and a set of child nodes for each SPI slave on the bus.  For this
+    discussion, it is assumed that the system's SPI controller is in
+    SPI master mode.  This binding does not describe SPI controllers
+    in slave mode.
+
+    The SPI master node requires the following properties:
+    - #address-cells  - number of cells required to define a chip select
+			address on the SPI bus.
+    - #size-cells     - should be zero.
+    - compatible      - name of SPI bus controller following generic names
+			recommended practice.
+    No other properties are required in the SPI bus node.  It is assumed
+    that a driver for an SPI bus device will understand that it is an SPI bus.
+    However, the binding does not attempt to define the specific method for
+    assigning chip select numbers.  Since SPI chip select configuration is
+    flexible and non-standardized, it is left out of this binding with the
+    assumption that board specific platform code will be used to manage
+    chip selects.  Individual drivers can define additional properties to
+    support describing the chip select layout.
+
+    SPI slave nodes must be children of the SPI master node and can
+    contain the following properties.
+    - reg             - (required) chip select address of device.
+    - compatible      - (required) name of SPI device following generic names
+			recommended practice
+    - spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz
+    - spi-cpol        - (optional) Empty property indicating device requires
+			inverse clock polarity (CPOL) mode
+    - spi-cpha        - (optional) Empty property indicating device requires
+			shifted clock phase (CPHA) mode
+
+    SPI example for an MPC5200 SPI bus:
+		spi@f00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
+			reg = <0xf00 0x20>;
+			interrupts = <2 13 0 2 14 0>;
+			interrupt-parent = <&mpc5200_pic>;
+
+			ethernet-switch@0 {
+				compatible = "micrel,ks8995m";
+				spi-max-frequency = <1000000>;
+				reg = <0>;
+			};
+
+			codec@1 {
+				compatible = "ti,tlv320aic26";
+				spi-max-frequency = <100000>;
+				reg = <1>;
+			};
+		};
+
 VII - Marvell Discovery mv64[345]6x System Controller chips
 ===========================================================
 

arch/powerpc/platforms/52xx/Kconfig

 config PPC_MPC52xx
 	bool "52xx-based boards"
 	depends on PPC_MULTIPLATFORM && PPC32
-	select FSL_SOC
 	select PPC_CLOCK
 	select PPC_PCI_CHOICE
 
@@ -48,6 +47,7 @@ config PPC_MPC5200_BUGFIX
 config PPC_MPC5200_GPIO
 	bool "MPC5200 GPIO support"
 	depends on PPC_MPC52xx
+	select GENERIC_GPIO
 	select HAVE_GPIO_LIB
 	help
 	  Enable gpiolib support for mpc5200 based boards

drivers/of/of_i2c.c

@@ -91,8 +91,6 @@ void of_register_i2c_devices(struct i2c_adapter *adap,
 		}
 
 		info.irq = irq_of_parse_and_map(node, 0);
-		if (info.irq == NO_IRQ)
-			info.irq = -1;
 
 		if (of_find_i2c_driver(node, &info) < 0) {
 			irq_dispose_mapping(info.irq);

include/asm-powerpc/mpc52xx_psc.h

@@ -60,10 +60,12 @@
 #define MPC52xx_PSC_RXTX_FIFO_ALARM	0x0002
 #define MPC52xx_PSC_RXTX_FIFO_EMPTY	0x0001
 
-/* PSC interrupt mask bits */
+/* PSC interrupt status/mask bits */
 #define MPC52xx_PSC_IMR_TXRDY		0x0100
 #define MPC52xx_PSC_IMR_RXRDY		0x0200
 #define MPC52xx_PSC_IMR_DB		0x0400
+#define MPC52xx_PSC_IMR_TXEMP		0x0800
+#define MPC52xx_PSC_IMR_ORERR		0x1000
 #define MPC52xx_PSC_IMR_IPC		0x8000
 
 /* PSC input port change bit */
@@ -92,6 +94,34 @@
 
 #define MPC52xx_PSC_RFNUM_MASK	0x01ff
 
+#define MPC52xx_PSC_SICR_DTS1			(1 << 29)
+#define MPC52xx_PSC_SICR_SHDR			(1 << 28)
+#define MPC52xx_PSC_SICR_SIM_MASK		(0xf << 24)
+#define MPC52xx_PSC_SICR_SIM_UART		(0x0 << 24)
+#define MPC52xx_PSC_SICR_SIM_UART_DCD		(0x8 << 24)
+#define MPC52xx_PSC_SICR_SIM_CODEC_8		(0x1 << 24)
+#define MPC52xx_PSC_SICR_SIM_CODEC_16		(0x2 << 24)
+#define MPC52xx_PSC_SICR_SIM_AC97		(0x3 << 24)
+#define MPC52xx_PSC_SICR_SIM_SIR		(0x8 << 24)
+#define MPC52xx_PSC_SICR_SIM_SIR_DCD		(0xc << 24)
+#define MPC52xx_PSC_SICR_SIM_MIR		(0x5 << 24)
+#define MPC52xx_PSC_SICR_SIM_FIR		(0x6 << 24)
+#define MPC52xx_PSC_SICR_SIM_CODEC_24		(0x7 << 24)
+#define MPC52xx_PSC_SICR_SIM_CODEC_32		(0xf << 24)
+#define MPC52xx_PSC_SICR_GENCLK			(1 << 23)
+#define MPC52xx_PSC_SICR_I2S			(1 << 22)
+#define MPC52xx_PSC_SICR_CLKPOL			(1 << 21)
+#define MPC52xx_PSC_SICR_SYNCPOL		(1 << 20)
+#define MPC52xx_PSC_SICR_CELLSLAVE		(1 << 19)
+#define MPC52xx_PSC_SICR_CELL2XCLK		(1 << 18)
+#define MPC52xx_PSC_SICR_ESAI			(1 << 17)
+#define MPC52xx_PSC_SICR_ENAC97			(1 << 16)
+#define MPC52xx_PSC_SICR_SPI			(1 << 15)
+#define MPC52xx_PSC_SICR_MSTR			(1 << 14)
+#define MPC52xx_PSC_SICR_CPOL			(1 << 13)
+#define MPC52xx_PSC_SICR_CPHA			(1 << 12)
+#define MPC52xx_PSC_SICR_USEEOF			(1 << 11)
+#define MPC52xx_PSC_SICR_DISABLEEOF		(1 << 10)
 
 /* Structure of the hardware registers */
 struct mpc52xx_psc {
@@ -132,8 +162,12 @@ struct mpc52xx_psc {
 	u8		reserved5[3];
 	u8		ctlr;		/* PSC + 0x1c */
 	u8		reserved6[3];
-	u16		ccr;		/* PSC + 0x20 */
-	u8		reserved7[14];
+	/* BitClkDiv field of CCR is byte swapped in
+	 * the hardware for mpc5200/b compatibility */
+	u32		ccr;		/* PSC + 0x20 */
+	u32		ac97_slots;	/* PSC + 0x24 */
+	u32		ac97_cmd;	/* PSC + 0x28 */
+	u32		ac97_data;	/* PSC + 0x2c */
 	u8		ivr;		/* PSC + 0x30 */
 	u8		reserved8[3];
 	u8		ip;		/* PSC + 0x34 */