Commit c2a653de authored by Masahiro Yamada's avatar Masahiro Yamada Committed by Wolfram Sang

i2c: uniphier-f: fix timeout error after reading 8 bytes

I was totally screwed up in commit eaba6878 ("i2c: uniphier-f:
fix race condition when IRQ is cleared"). Since that commit, if the
number of read bytes is multiple of the FIFO size (8, 16, 24... bytes),
the STOP condition could be issued twice, depending on the timing.
If this happens, the controller will go wrong, resulting in the timeout
error.

It was more than 3 years ago when I wrote this driver, so my memory
about this hardware was vague. Please let me correct the description
in the commit log of eaba6878.

Clearing the IRQ status on exiting the IRQ handler is absolutely
fine. This controller makes a pause while any IRQ status is asserted.
If the IRQ status is cleared first, the hardware may start the next
transaction before the IRQ handler finishes what it supposed to do.

This partially reverts the bad commit with clear comments so that I
will never repeat this mistake.

I also investigated what is happening at the last moment of the read
mode. The UNIPHIER_FI2C_INT_RF interrupt is asserted a bit earlier
(by half a period of the clock cycle) than UNIPHIER_FI2C_INT_RB.

I consulted a hardware engineer, and I got the following information:

UNIPHIER_FI2C_INT_RF
    asserted at the falling edge of SCL at the 8th bit.

UNIPHIER_FI2C_INT_RB
    asserted at the rising edge of SCL at the 9th (ACK) bit.

In order to avoid calling uniphier_fi2c_stop() twice, check the latter
interrupt. I also commented this because it is obscure hardware internal.

Fixes: eaba6878 ("i2c: uniphier-f: fix race condition when IRQ is cleared")
Signed-off-by: default avatarMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: default avatarWolfram Sang <wsa@the-dreams.de>
parent 0544ee4b
......@@ -173,8 +173,6 @@ static irqreturn_t uniphier_fi2c_interrupt(int irq, void *dev_id)
"interrupt: enabled_irqs=%04x, irq_status=%04x\n",
priv->enabled_irqs, irq_status);
uniphier_fi2c_clear_irqs(priv, irq_status);
if (irq_status & UNIPHIER_FI2C_INT_STOP)
goto complete;
......@@ -214,7 +212,13 @@ static irqreturn_t uniphier_fi2c_interrupt(int irq, void *dev_id)
if (irq_status & (UNIPHIER_FI2C_INT_RF | UNIPHIER_FI2C_INT_RB)) {
uniphier_fi2c_drain_rxfifo(priv);
if (!priv->len)
/*
* If the number of bytes to read is multiple of the FIFO size
* (msg->len == 8, 16, 24, ...), the INT_RF bit is set a little
* earlier than INT_RB. We wait for INT_RB to confirm the
* completion of the current message.
*/
if (!priv->len && (irq_status & UNIPHIER_FI2C_INT_RB))
goto data_done;
if (unlikely(priv->flags & UNIPHIER_FI2C_MANUAL_NACK)) {
......@@ -253,6 +257,13 @@ static irqreturn_t uniphier_fi2c_interrupt(int irq, void *dev_id)
}
handled:
/*
* This controller makes a pause while any bit of the IRQ status is
* asserted. Clear the asserted bit to kick the controller just before
* exiting the handler.
*/
uniphier_fi2c_clear_irqs(priv, irq_status);
spin_unlock(&priv->lock);
return IRQ_HANDLED;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment